IMPORTANT SAFETY INSTRUCTIONS

Transcription

1 BAS8 SUBWOOFER

2 IMPORTANT SAFETY INSTRUCTIONS 1

3 CONGRATULATIONS ON SELECTING A CARVER SUBWOOFER CARVER is one of the most highly-regarded brands of speakers available today. We appreciate your business and we stand committed to providing our customers with the highest degree of quality and service in the industry. The CARVER BAS8 subwoofers are superb choices for bass reinforcement of almost every type of audio system. They have been designed with advanced technology components that accurately reproduce low frequencies in all types of music. CARVER speakers provide the best value and quality possible for your home audio needs. CARVER SUBWOOFER FEATURES >>FULL PERFORMANCE CONTROL Your CARVER subwoofer also features a rear-mounted, low-pass crossover adjustment and a switchable phase control (0 or 180 degrees) to ensure optimal system integration, providing a seamless blend of low frequency in any audio system. >>MUSIC SENSE CIRCUITRY FOR AUTOMATIC POWER CONTROL There are two choices for power modes with an CARVER powered subwoofer; On, and Auto. When the Auto On position is selected, your subwoofer is in standby mode until an input signal is detected. Power will turn on whenever a minimal amount of signal is detected on the RCA jacks and off again when no signal is present for approximately 8 minutes. >>NICKEL-PLATED STEREO RCA LINE-LEVEL AND LOUDSPEAKER-LEVEL INPUTS All CARVER powered subwoofers feature stereo RCA line-level inputs as well for a direct connection from the receiver or processor. Each model is also equipped with nickel-plated high level five-way binding-post inputs and outputs. >> HIGH EFFICIENCY CLASS D AMPLIFIER CIRCUIT WHICH SAVED LARGER HEAT SINK. >> STANDBY POWER CONSUMPTION 0.5 W IS IN ACCORDANCE WITH UP-DATED ERP STANDARDS. 2

4 INSTALLATION - FIRST STEPS PLACING YOUR CARVER SUBWOOFER CARVER powered subwoofers are designed to make your music come alive. However, where you place the subwoofer can have an effect on the performance that you receive. All rooms are different, but the strongest output will likely occur if you place your subwoofer in a corner of the room on the same wall as your front channel speakers. This is known as the boundary effect and will emphasize certain bass frequencies while canceling others. Some listeners will find this to be the best sounding result, while others may find it overly boomy or muddy Experiment with the placement options available to you and use the tuning instructions that follow in the set up section of this manual. CONNECTING YOUR CARVER SUBWOOFER For line level connections, use high quality RCA cables that feature low impedance, shielding and high quality connectors. Use two-conductor loudspeaker wire for high level connections to your subwoofer and to any satellite loudspeakers that may be connected as well. DO NOT connect wiring to both sets of inputs simultaneously. Example If you are using loudspeaker level inputs, DO NOT connect an RCA cable to the subwoofer at the same time. Recommended placement of subwoofer in one of the front corners of the room. INSTALLATION CONTROLS CONTROLS Your CARVER Subwoofer s controls and connectors are on the rear panel as shown here PHASE: Use this control to set the subwoofer s phase response to or AUTO: Auto turn on mode ON: Amplifier ON 3 POWER INDICATOR GREEN: The subwoofer is on RED: The subwoofer is standby or protect ORANGE: The subwoofer is clipping 4 FREQ: Use this control to set subwoofer s low-pass crossover frequency from 30 to 100 Hz. In the by pass position, the crossover control has no effect. You should set this to bypass if your processor provides it's own subwoofer crossover frequency control LEVEL: Adjusts the output (Volume) Level of the Subwoofer. 3 13

5 6 LOW LEVEL INPUT: These connect with RCA type cables from the Line-level outputs of your receiver or preamp. 7 LOW LEVEL OUTPUT: Line level RCA outputs provide a line level full range output for the connection of additional subwoofers or other audio devices. This output is only available when a signal is present at the low level input. 8 HIGH LEVEL IN: Connect the speaker level outputs from your full range amplifier to these input terminals marked "FROM AMPLIFIER". 9 HIGH LEVEL OUT: Connect the high level output terminals marked "TO SPEAKERS" to your passive satellite speakers. 10 POWER SWITCH: Press the switch to turn on/off the subwoofer. 11 AC LINE FUSE: The subwoofer is supplied with a conservative slow-blow type fuse to protect the electronics. If this fuse fails, replace it with the exact same type and current rating for your local AC voltage. 12 IEC POWER CONNECTOR: The subwoofer comes with a detachable line cord that attaches here. Make sure it is firmly pushed into place. Connect the other end to an AC outlet that is properly configured for the type of plug and has the correct Voltage for your model. 13 VOLTAGE SELECTOR SWITCH: 115/230 Voltage select or switch. RECORD YOUR FAVORITE SETTINGS HERE: FREQ. LEVEL REV NOR PHASE Note: Some Home Theater processors and receivers have an internal crossover adjustment which allows you to verify how much of the bass frequency range is sent to the subwoofer. 4

6 Stereo amplifier POWER MENU MUTE GREEN: ON RED: STANDBY/PRT ORANGE: CLIP INPUT In these systems, it is recommended that you set your subwoofer s own crossover control to maximum frequency, or Bypass. You can then make any crossover frequency adjustments using your Home Theater processor or receiver controls. If the subwoofer s internal crossover is set to a frequency lower than the one on your Home Theater processor or receiver, there would be a hole in the mid-bass, and bass information would be missing. INSTALLATION - GETTING CONNECTED CARVER powered subwoofers are among the most flexible on the market today and can be configured for use in many different applications, as shown in the figures below. CARVER POWERED SUBWOOFER INSTALLATION USING LOW- LEVEL INPUTS AUTO ON FREQ. ON AUTO POWER REV NOR PHASE LEVEL LOW LEVEL OUTPUT L R HIGH LEVEL IN/OUT FROM AMPLIFIER TO SPEAKERS + + L R L R - - Loop to an Optional Second Subwoofer Left & Right Line Level Output (Optional) POWER BAS8 Do Not Use These When Using the Low Level Inputs OFF ON Code: High Level / Speaker Level Output 5

7 Stereo amplifier POWER MENU MUTE CARVER POWERED SUBWOOFER INSTALLATION USING HIGH-LEVEL INPUTS High Level/ Speaker Level Output Do Not Use These When Using the High Level Inputs SPECIFICATIONS Power Rating Frequency Response Signal to Noise Ratio Distortion(THD) Input Impedance Driver Dimensions(W x D x H) Weight 8 Ohms +/-3 db 250Watt RMS 30 Hz-100Hz 90 db A-weighted <0.1% 12K ohms 8 8 ohm 400 W 290 x 265 x 270 mm 14.0 kg 6

8 C ARVER HOLDINGS GROUP LTD.