Once the device has been physically installed and tested, follow the below steps to connect/pair it to your Rogers Smart Home Monitoring Touchpad.

Transcription

1 Set-Up Guide In-Wall Switch or Dimmer Jasco Package Contents: 1 In-Wall Switch or Dimmer device 2 Manufacturer s Installation Guide for installing the device 3 Rogers Set-Up Guide for pairing the device to your Rogers Smart Home Monitoring system Device Installation Please refer to the enclosed Manufacturer s Installation Guide. To avoid injury, read all set-up and safety information included in your package before setting up and using your device. Please follow all provincial and/or municipal regulations when installing your device. If you encounter a problem setting up your in-wall light switch or dimmer, please call Rogers Technical Support at Once the device has been physically installed and tested, follow the below steps to connect/pair it to your Rogers Smart Home Monitoring Touchpad. In-Wall Auxiliary Switch Note: If you are installing the In-wall Switch or Dimmer to control a light or electrical device that is also controlled from a 2nd or 3rd location (i.e. a 3-way or 4-way switch set-up), installation of the In-wall Auxiliary Switch is required at these additional locations for integration with your Smart Home Monitoring System. For installation of the In-Wall Auxiliary Switch, please refer to the Manufacturer s Installation Guide provided with that device. Note: the Auxiliary Switch does not need to be paired to your Smart Home Monitoring system. 1 In-Wall Switch or Dimmer Jasco

2 Prepare the Device for Pairing Please pair one device at a time. Once the device has been physically installed and the electrical power is turned on to the device, the LED on the front of the device should begin to blink for approximately 2 minutes. While the LED is blinking, the device is ready to be paired with the Smart Home Monitoring System. Proceed to the Connecting the Device to Your System section of this guide. If the LED is not blinking (or stops blinking), the device needs to be reset to factory default settings before it can be connected to your system. Proceed as follows to reset the device to factory default settings: Resetting the In-Wall Switch Device 1 Press the top of the rocker (ON switch) 10 times. The LED should start blinking. 2 Proceed to the Connecting the Device to Your System section of this guide. Resetting the In-Wall Dimmer Device Circle indicates top of rocker. 1 Pull out the air gap switch. 2 Press and hold the top of the rocker (ON switch). 3 Push the air gap switch back to its original position while holding the top of the rocker. After 2 seconds the LED will start to blink. 4 Release the top of the rocker once the LED starts blinking. 5 Proceed to the Connecting the Device to Your System section of this guide. Circle indicates air gap switch. 2 In-Wall Switch or Dimmer Jasco

3 g Connecting the Device to your System 1 Ensure system is disarmed. 2 On the Touchpad, select the Settings app from the Home Screen. 3 Enter your Master Access Code (4-digit code). Your Master Access Code is the same code that you use to manage your system. 4 Select Home Devices under the Categories list. 5 Scroll down and select Lighting, then select Add Lights. 3 In-Wall Switch or Dimmer Jasco g

4 Connecting the Device to your System 6 On the Locating Door Lock Devices screen press Next, and the system will take up to 30 seconds to find the device. 7 On the SHM Touchpad a pairing icon: will appear and change to an On/Off Light or Dimmable Light icon once pairing is complete. Please note this may take 2 to 5 minutes. 8 Click Done once the icon appears and hit Next to confirm. 9 The icon will be shown again. Tap on the icon to customize its name (e.g. Living Room Light). If you have a dimmable light, ensure that Dimmable is set to Yes 10 Click Next when done. 11 Click Return to Menu to complete the pairing of the device. 4 In-Wall Switch or Dimmer Jasco

5 g Congratulations! Your In-wall Switch or In-wall Dimmer is now part of your Smart Home Monitoring system. You will now be able to remotely control your lights with your Touchpad, your smartphone app and through the Web Conrol Centre. In-Wall Light Switch Features Automate your In-Wall Light Switch using Rules on the Web Control Centre at smarthome.rogers.com. Rule Creation Set-up rules such as: Automatically turn on lights when the front door is opened. Turn lights on or off at scheduled times when you re away from home. Set an SHM motion sensor to turn on lights when you walk through your house in the middle of the night. Rules are not impacted by changing the name of the light as they follow the serial number of the device SHM-JSCWS In-Wall Switch or Dimmer Jasco g