Chapter 2 Roof Downspout Controls

Size: px
Start display at page:

Download "Chapter 2 Roof Downspout Controls"

Transcription

1 Chapter 2 Roof Downspout Controls 2.1 Description This section presents the criteria for design and implementation of roof downspout controls. Roof downspout controls are simple pre-engineered designs for infiltrating and/or dispersing runoff from roof areas for the purposes of increasing opportunities for groundwater recharge and reduction of runoff volumes from new development or redevelopment. This chapter may also be applicable for onsite management of other impervious surfaces, as allowed by Environmental Services. This chapter provides guidance for roof downspout controls for meeting the intent of Minimum Requirement #5, Onsite Stormwater Management. It may be possible to use this guidance for meeting the intent of Minimum Requirement #7 as well. Environmental Services may require additional soils or site information for larger projects when using the guidance in this chapter. Roof downspout controls are used in conjunction with, and in addition to, any additional flow control facilities that may be necessary to mitigate stormwater impacts from the overall development. Implementation of roof downspout controls may reduce the total effective impervious area and result in less runoff from these surfaces. Flow credits for implementing infiltration and dispersion for controls are available as follows: If all the roof runoff is infiltrated according to the requirements of this section, the roof area may be discounted from the total project area used for determining flow control thresholds and sizing stormwater facilities. If roof runoff is dispersed according to the requirements of this section on lots greater than 22,000 square feet and the vegetative flow path 1 is 50 feet or longer through undisturbed native landscape or lawn/landscape area that meets BMP L613, the roof area may be modeled as grassed surface. Additional information on flow credits is available in Volume 6, Chapter 2. NOTE: Flow credits only apply to flow control thresholds. Flow credits do not apply to water quality thresholds. 2.2 Selection of Roof Downspout Controls Per Minimum Requirement #5, Onsite Stormwater Management, all projects shall employ roof downspout controls to infiltrate, disperse and retain stormwater onsite to the maximum extent practicable. The applicant is required to control downspouts in the following order of preference: Rain gardens (Section 2.4) Downspout infiltration systems (Section 2.6) Downspout dispersion systems (Section 2.7) - only allowed if it can be demonstrated that infiltration is not feasible. Collect and convey to the City system (Section 2.8) - only allowed if it can be demonstrated that infiltration and dispersion are not feasible. 1.Vegetative flow path is measured from the downspout or dispersion system discharge point to the downstream property line, stream, wetland, or other impervious surface. Volume Chapter 2

2 City of Tacoma 2012 SWMM Drywells are generally prohibited within the City of Tacoma. Contact Environmental Services if a drywell is proposed. 2.3 Roof Downspout Infiltration Setbacks and Site Controls Setback requirements are generally required by the City, uniform building code requirements, the Tacoma-Pierce County Health Department, or other state regulation. Where a conflict between setbacks occurs, the City shall require compliance with the most stringent of the setback requirements from the various codes/regulations. The following are the minimum setbacks required per this manual. At least 100 feet from drinking water wells and springs used for public water supplies. Infiltration facilities upgradient of drinking water wells and within 1, 5 and 10-year time of travel zones must comply with the Health Department requirements (Washington Wellhead Protection Program, DOH, Publication # ). At least 10 feet from any building structure and at least 5 feet from any other structure or property line unless approved in writing by Environmental Services. Rain gardens designed for infiltration shall not be built on slopes steeper than 20%. A geotechnical analysis and report shall be required on slopes over 15% or if located within 200 feet of the top of steep slopes (40% or greater) or a landslide hazard area. More stringent setbacks may be required based upon Tacoma Municipal Code. At least 10 feet from septic tank and septic drainfields. Additional setbacks from DOH Publication # , Onsite Sewage Systems, Chapter A WAC may apply. Shall not be located upstream of residential septic systems unless topography or a hydrology analysis clearly indicates that subsurface flows will not impact the drainfield. Environmental Services may require additional setbacks or analysis for infiltration facilities proposed to be sited within the influence of known contaminated sites or abandoned landfills. 2.4 Procedure for Evaluating Feasibility of Downspout Infiltration Downspout infiltration is considered feasible if a rain garden or infiltration trench designed to meet the minimum design criteria specified in Section 2.5 or 2.6 can fit within the proposed project site and meet the setback site constraint requirements described in Section 2.3. To determine if downspout infiltration is feasible, a site-specific soils report may be required. To determine if a soils report is required, evaluate if the minimum rain garden size from Table 3-4 or the minimum trench length from Table 3-5 can fit on the project site while maintaining the design criteria of Section or Section If the rain garden or infiltration trench can fit on the site and maintain the design criteria, a site-specific soils report is required. For single lots the soils report must, at a minimum: Be prepared by a professional soils scientist certified by the Soil Science Society of America (or an equivalent national program), a locally licensed onsite sewage designer, other suitably-trained professional engineer, geologist, hydrogeologist, or engineering geologist registered in the State of Washington, or persons working under the supervision of one of the soils professionals listed here; Contain at least one soils log a minimum of 4 feet deep (from proposed grade) taken at the location of the proposed infiltration system; Chapter Volume 3

3 Identify the SCS series of the soil and the USDA textural class of the soil horizon through the depth of the log; Note any evidence of high groundwater level, such as mottling; and Note the depth to groundwater. The design of the rain garden or infiltration trench shall be based upon the soil located at the proposed bottom of the rain garden or infiltration facility. If multiple soils logs are conducted, the least infiltrative soil found at the proposed bottom of the infiltration facility shall be used for design. NOTE: On sites where soils are insufficient for infiltration based on the soils report and available land to construct facilities and meet setback requirements, a downspot dispersion system per Section 2.7 may be feasible in lieu of infiltration. 2.5 Roof Downspout Rain Gardens Purpose and Definition Bioretention areas are shallow stormwater retention facilities designed to mimic forested systems by controlling stormwater through detention, infiltration, and evapotranspiration Design Criteria Groundwater Separation A minimum of 18 inches of separation is required between the lowest elevation of the bioretention soil or any underlying gravel infiltration layer and the seasonal high groundwater elevation or other impermeable layer Flow Entrance/Presetting Flow velocity entering the facility shall be less than 1 ft/sec for the 100-year, 24-hour storm event. If 1 ft/sec cannot be obtained, Environmental Services may approve the discharge with the addition of a designed flow dispersion or energy dissipation device. Use one of the following types of flow entrances (other alternatives may be considered on a case-by-case basis): Dispersed, low velocity flow across a grade or landscape area. A minimum 2-inch grade change between the edge of the contributing area and flow entrance is required. Pipe flow entrance. The inlet pipe invert elevation shall be higher than the overflow elevation. Place rock or other erosion protection material at the facility entrance to dissipate energy and/or provide flow dispersion. Environmental Services may require flow dispersion for rain gardens depending upon type of inlet design and size of the facility. Do not place plants directly in the entrance flow path as they can restrict or concentrate flows. Install flow diversion and erosion control measures to protect the bioretention area from sedimentation until the upstream area is stabilized. Volume Chapter 2

4 City of Tacoma 2012 SWMM Based upon project site constraints, Environmental Services may require a presettling facility Cell Ponding Area The ponding depth shall be 12 inches. The surface pool drawdown time shall be less than 24 hours. If the rain garden is sized per Table 3-4, this requirement is met. Bioretention sizing is based on bottom area. Once bottom area is determined, top area shall be based upon side slopes and total depth of facility. The minimum freeboard measured from the maximum ponding water surface elevation to the top of the facility shall be 2 for drainage areas less than 1,000 square feet and 6 for drainage areas 1,000 square feet or greater. If berming is used to achieve the minimum top elevation, maximum slope on berm shall be 3H:1V, and minimum top width of design berm shall be 1 foot. Soil for berming shall be imported bioretention soil or amended native soil compacted to a minimum of 90% dry density Overflow Unless designed for full infiltration of the entire runoff volume, bioretention systems must include an overflow. Rain gardens sized using Table 3-4 are designed for full infiltration and are not required to have an overflow. An emergency overflow pathway shall be provided for all facilities to ensure that all potential overflows are directed into the downstream conveyance system or the public right of way Bioretention Soil Mix The bioretention soil mix (BSM) shall: Have a 60% aggregate component as represented in Table 3-2 below and a 40% compost component as represented in Table 3-3 below. Table 3-2: Bioretention Soil Mix Aggregate Component Gradation Aggregate Component (60% by Volume) Sieve Size Percent Passing 3/8 100 # # # # # The compost component shall be stable, mature, and derived from organic waste materials including yard debris, wood wastes or other organic matter. Compost must meet the Washington State compost regulations in WAC , which is available at and meet the the following: Chapter Volume 3

5 Have a compost component meeting the size requirements in Table 3-3 Table 3-3: Bioretention Soil Mix Compost Component Gradation Sieve Size Have a ph between 5.5 and 8.0 Compost Component Percent Passing / / Have a manufactured inert material (plastic, concrete, ceramics, metal, etc.) less than 1.0% by weight Have a organic matter content between 45 and 65 percent dry weight bases as determined by TMECC 05.07A, Loss-On-Ignition Organic Matter Method. Have a soluble salt content less than 6.0 mmhos/cm tested in accordance with TMECC A, 1.5 Slurry Method, Mass Basis. Have a maturity greater than 80% in accordance with TMECC A, Germination and Vigor. Have a stability at 7 or below in accordance with TMECC B, Carbon Dioxide Evolution Rate. Have a compost product that contains a minimum of 65% and up to 100% by volume recycled plant waste as defined in WAC as Type 1 Feedstocks. A maximum of 35% by volume of other approved organic waste as defined in WAC as Type III, including post-consumer food waste but not including biosolids, may be substituted for recycled plant waste. Have a carbon to nitrogen ratio of less than 25:1 as determined using TMECC Total Carbon and TMECC 04.02D Total Kjeldhal Nitrogen. A ratio up to 35:1 can be used if all plants are native species. The Washington State Department of Ecology keeps a list of approved composting facilities in Washington at: Minimum depth of bioretention soil mix must be 18 inches. Contact Environmental Services for assistance in verifying bioretention soil mix suitability Planting Plants must be tolerant of summer drought, ponding fluctuations, and saturated soil conditions. Consider rooting depth when choosing plants. Roots must not damage underground infrastructure. Consider adjacent plant communities and avoid potential invasive species. Consider aesthetics, rain gardens should blend into surrounding landscapes. Low Impact Development: Technical Guidance Manual for Puget Sound is a good tool for selecting proper bioretention plants. Volume Chapter 2

6 City of Tacoma 2012 SWMM Submit a planting plan showing the type, location and size of each plant. Irrigation may be required until plants are fully established and in the summer months Mulch Layer Bioretention facilities should be designed with a mulch layer. Properly selected mulch material reduces weed establishment, regulates soil temperatures and moisture, and adds organic matter to the soil. Mulch should be free of weed seeds, soil, roots, and other material that is not trunk or branch wood and bark. Mulch shall not include grass clippings, mineral aggregate or pure bark. Mulch shall be: Compost in the bottom of the facilities, depth 3 inches Wood chip mulch composed of shredded or chipped hardwood or softwood on side slopes, depth 4 inches. A dense groundcover can be used as an alternative to mulch although mulch shall be required until the dense groundcover is established Sizing Table 3-4 shall be used for sizing facilities managing roof runoff to meet Minimum Requirement #5, Onsite Stormwater Management only. See Volume 6, BMP L630 for sizing facilities for projects that must comply with Minimum Requirement #6, Runoff Treatment and/or Minimum Requirement #7, Flow Control. Table 3-4 gives the square footage of the bottom of the rain garden per 1000 square feet of roof area. Table 3-4: Sizing Table for Rain Gardens Soil Type Rain Garden Bottom (square feet) Coarse sands and cobbles 50 Medium sands 50 Fine sands, loamy sands 50 Sandy loam 50 Loam 150 For sites with soils other than given in Table 3-4 or sites proposing an underdrain, an engineered design will be required. Refer to Volume 6, BMP L630 for sizing guidance Flow Credit If roof runoff is infiltrated according to the requirements of this section, the roof area may be deducted from the project area used for determining flow control thresholds and sizing stormwater facilities for flow control only. The deduction cannot be applied to pollutantgenerating surfaces that require water quality treatment. If the thresholds for water quality treatment are met, water quality is required. A Stormwater Site Plan and Construction Stormwater Pollution Prevention Plan are still required. Chapter Volume 3

7 2.5.4 General Construction Criteria Do not install or excavate during soil saturation periods. Excavation and soil placement should be done from equipment operating adjacent to the facility no heavy equipment should be operated in the facility if possible. If equipment must be operated within the facility, use lightweight, low ground pressure equipment and scarify the base to reduce compaction upon completion. Do not use fully excavated bioretention facilities for erosion and sedimentation control during construction; Consider partial excavation of bioretention cells prior to construction (to within 12 inches above finished bottom grade) for use as temporary stormwater detention, if necessary. Clogged soil and silt shall be removed during excavation to finished bottom grade prior to installing bioretention cell profile. Scarify sides and bottom to roughen where heavy equipment may have compacted soil. Ensure the bioretention facility is protected from erosion and sedimentation until all contributory areas are fully stabilized. If sedimentation occurs within the bioretention facility, excavate the area a minimum of 12 inches below final grade to remove sediment Maintenance Criteria Per Minimum Requirement #10, an operation and maintenance plan shall be prepared for all stormwater management facilities. See Volume 1, Appendix D, Maintenance Checklist #22 for specific maintenance requirements for rain gardens. Maintenance shall be a basic consideration in design and cost-determination of the stormwater management facility. Any standing water removed during the maintenance operation must be disposed of in a City approved manner. See the dewatering requirements in Volume 4 of this manual. Pretreatment may be necessary. Solids must be disposed of in accordance with state and local waste regulations. Facilities shall be constructed such that the facility can be easily inspected by one person. This may require the construction of additional inspection ports or access manholes. 2.6 Downspout Infiltration Systems Downspout infiltration systems are trenches designed for flow control and/or complying with Minimum Requirement #5 and are intended only for use in infiltrating runoff from roof downspout drains. They are not designed to directly infiltrate runoff from pollutant-generating impervious surfaces. Volume 5, Chapter 5 contains a discussion of infiltration trenches for water quality treatment Flow Credit for Roof Downspout Infiltration If roof runoff is infiltrated according to the requirements of this section, the roof area may be discounted from the project area used for determining flow control thresholds and sizing flow control facilities. The deduction cannot be applied to pollutant-generating surfaces. If the thresholds for water quality treatment are met, water quality treatment is required. A Stormwater Site Plan and Construction Stormwater Pollution Prevention Plan are still required. Volume Chapter 2

8 City of Tacoma 2012 SWMM Design Criteria for Infiltration Trenches Figure 3-1 shows a typical downspout infiltration trench system, and Figure 3-2 presents an alternative infiltration trench system for sites with coarse sand and cobble soils. Applicants may use either of these designs in conjunction with the soils table below or may model the site separately. Modeling must be conducted by a licensed engineer in the State of Washington. General 1. The following minimum lengths (in linear feet [LF]) per 1,000 square feet of roof area based on soil type may be used for sizing downspout infiltration trenches. For soil types other than those presented in Table 3-5, additional geotechnical information and/or engineering analysis may be required by Environmental Services. Table 3-5: Downspout Infiltration Length for USDA Soil Type USDA Soil Type Trench Length (linear feet) Coarser 20 Sand 85 Loamy Sand 90 Sandy Loam 115 Loam 270 Silt Loam Maximum length of trench must not exceed 100 feet from the inlet sump. 3. Minimum spacing between trenches shall be 4 feet measured from the edge of trench. 4. Non-woven geotextile fabric shall be placed around the walls, bottom and top of the trench aggregate. A 6-inch minimum layer of sand may be used as a filter media at the bottom of the trench instead of the geotextile. Volume 5, Appendix C contains specifications for geotextile fabric. 5. A minimum of three feet of separation is required from the proposed final grade to the seasonal high groundwater table. 6. A minimum of 1 foot of separation is required from the bottom of the infiltration trench to the seasonal high groundwater table. 7. Infiltration trenches may be placed in fill material if the fill is placed and compacted under the direct supervision of a geotechnical engineer or professional civil engineer with geotechnical expertise, and if the measured infiltration rate is at least 8 inches per hour. Trench length in fill must be 60 linear feet per 1,000 square feet of roof area. Infiltration rates can be tested using the methods described in Section Trenches may be located under pavement if a small yard drain or catch basin with grate cover is placed at the end of the trench pipe such that overflow would occur out of the catch basin at an elevation at least one foot below that of the pavement, and in a location which can accommodate the overflow without creating a significant adverse impact to downhill properties or drainage systems. This is intended to prevent saturation of the pavement in the event of system failure. Chapter Volume 3

9 Maintenance Criteria Per Minimum Requirement #10, an operation and maintenance plan shall be prepared for all stormwater management facilities. See Volume 1, Appendix D, Maintenance Checklist #3 for specific maintenance requirements for infiltration trenches. Maintenance shall be a basic consideration in design and cost-determination of the stormwater management facility. Any standing water removed during the maintenance operation must be disposed of in a City approved manner. See the dewatering requirements in Volume 4 of this manual. Pretreatment may be necessary. Solids must be disposed of in accordance with state and local waste regulations. Facilities shall be constructed such that the facility can be easily inspected by one person. This may require the construction of additional inspection ports or access manholes. Volume Chapter 2

10 City of Tacoma 2012 SWMM 10' MINIMUM ¾ TO 1-½ WASHED ROCK Figure 3-1. Typical Downspout Infiltration Trench Chapter Volume 3

11 Figure 3-2. Alternative Infiltration Trench System for Coarse Sand and Gravel Volume Chapter 2

12 City of Tacoma 2012 SWMM Simple 10-foot trench per Trench X-Section above Maximum 50-foot trench w/notch board per Figure 3-4 Figure 3-3. Typical Downspout Dispersion Trench Chapter Volume 3

13 Figure 3-4. Standard Dispersion Trench with Notched Grade Board 2.7 Downspout Dispersion Systems Downspout dispersion systems are splash blocks or dispersion facilities that spread roof runoff over vegetated pervious areas. Dispersion attenuates peak flows by slowing entry of the runoff into the conveyance system, allowing for some infiltration, and providing some water quality benefits. Volume Chapter 2

14 City of Tacoma 2012 SWMM Application Downspout dispersion may be used on all sites that cannot infiltrate roof runoff and that meet the feasibility and setback requirements provided in the general design criteria below Flow Credit for Roof Downspout Dispersion If roof runoff is dispersed according to the requirements of this section, and the vegetative flow path 1 of the roof runoff is 25 feet or greater through undisturbed native landscape or lawn/ landscape area that meets BMP L613, the roof area may be modeled as a grassed surface for determining thresholds and sizing flow control devices. The deduction cannot be applied to pollutant-generating surfaces. If the thresholds for water quality treatment are met, water quality treatment is required General Design Criteria No erosion or flooding of downstream properties shall result. Downspout dispersion trenches designed as shown in Figure 3-3 or Figure 3-4 should be used for all downspout dispersion applications except where splash blocks are allowed. Perforated stub-out connections shall not be used. For sites with septic systems, the discharge point of all dispersion systems must be downgradient of the drainfield. This requirement may be waived if site topography clearly prohibits flows from intersecting the drainfield. For sites with septic systems, the discharge point must be downslope of the primary and reserve drainfield areas. This requirement may be waived if site topography clearly prohibits flows from intersecting the drainfield or where site conditions (soil permeability, distance between systems, etc) indicate that this is unnecessary. Place all dispersion systems at least 5 feet from any property line. If necessary, setbacks shall be increased from the minimum 5 feet in order to maintain a 1:1 side slope for future excavation and maintenance. Setback dispersion systems from sensitive areas, steep slopes, landslide hazard areas, and erosion hazard areas as goverened by the Tacoma Municipal Code. All dispersions systems shall be at least 10 feet from any structure. If necessary, setbacks shall be increased from the minimum 10 feet in order to maintain a 1H:1V side slope for future excavation and maintenance. For sites with multiple dispersion systems, a minimum separation of 10 feet is required between flowpaths. Environmental Services may require a larger separation based upon site conditions such as slope, soil type and total contributing area. Runoff discharged towards landslide hazard areas must be evaluated by a geotechnical engineer or a licensed geologist, hydrogeologist, or engineering geologist. The discharge point shall not be placed on or above slopes greater than 20% (5H:1V) or above erosion hazard areas without evaluation by a geotechnical engineer or qualified geologist and City approval. 1.Vegetative flow path is measured from the downspout or dispersion system discharge point to the downstream property line, stream, wetland, or other impervious surface. Chapter Volume 3

15 Design Criteria for Dispersion Trenches Design dispersion trenches as shown in Figure 3-3 and Figure 3-4. A vegetated flowpath of at least 25 feet in length must be maintained between the outlet of the trench and any property line, structure, stream, wetland, or impervious surface. A vegetated flowpath of at least 50 feet in length must be maintained between the outlet of the trench and any slope, 20% or greater. Sensitive area buffers may count towards flowpath lengths if approved by the City of Tacoma. Trenches serving up to 700 square feet of roof area may be simple 10-foot-long by 2-foot wide gravel filled trenches as shown in Figure 3-3. For roof areas larger than 700 square feet, a dispersion trench with notched grade board may be used as approved by the City. The total length of this design must not exceed 50 feet and must provide at least 10 feet of trench per 700 square feet of roof area. Design Criteria for Splashblocks A typical downspout splashblock is shown in Figure 3-5. In general, if the ground is sloped away from the foundation and there is adequate vegetation and area for effective dispersion, splashblocks will adequately disperse storm runoff. If the ground is fairly level, if the structure includes a basement, or if foundation drains are proposed, splashblocks with downspout extensions may be a better choice because the discharge point is moved away from the foundation. Downspout extensions can include piping to a splashblock/discharge point a considerable distance from the downspout, as long as the runoff can travel through a wellvegetated area as described below. A vegetated flow path of at least 50 feet shall be maintained between the discharge point and any property line, structure, steep slope, stream, wetland, lake, or other impervious surface. Sensitive area buffers may count toward flow path lengths. Flows shall not be directed onto sidewalks. A maximum of 700 square feet of roof area may drain to each splashblock. A splashblock or a pad of crushed rock (2 feet wide by 3 feet long by 6 inches deep) shall be placed at each downspout discharge point. Volume Chapter 2

16 City of Tacoma 2012 SWMM 2.8 Collect and Convey Figure 3-5. Typical Downspout Splashblock Dispersion Where it can be demonstrated that infiltration and dispersion are not feasible for roof downspout controls, it may be allowable to collect and convey to the City stormwater system. This may be either the curb, if present, or the actual pipe and structure conveyance system. Conveyance to the curb will only be allowed if a catch basin is located within 350 feet downstream of the discharge point. If a catch basin is not located within 350 feet of the discharge location, a storm main extension shall be required. Minimum pipe size for conveyance to the curb shall be 3 inches in diameter. Where capacity greater than a 3 inch diameter pipe is required, Environmental Services shall review the proposal and may require a storm main extension. NOTE: Environmental Services will only approve on a case-by-case basis those facilities that would require more than one through-curb discharge point. Chapter Volume 3

17 For total roof areas 2,000 to 5,000 sf, roof runoff may be allowed to be collected and conveyed to either the curb or directly connected to a structure. The runoff shall not be conveyed over driveways, sidewalks or other areas reserved for pedestrian traffic. A detail for the discharge shall be submitted to Environmental Services for review and approval. For roof areas between 5,001 sf and 9,999 sf, roof runoff may be allowed to be collected and conveyed to the curb or stormwater structure unless Minimum Requirement #7 applies and requires alternative mitigation. Capacity analysis of the road gutter, conveyance piping and catch basin leads will be required to ensure that adequate capacity exists (see Section 9.6). Environmental Services may require more than one through curb outlet for discharge to the curb. For roof areas 10,000 sf and greater, please refer to Minimum Requirement #7. No flow credits will be allowed for the collect and convey option. Volume Chapter 2

2.1.4 Roof Downspout Rain Gardens

2.1.4 Roof Downspout Rain Gardens 2008 SWMM, 2010 Revision City of Tacoma 2.1.4 Roof Downspout Rain Gardens Purpose and Definition Bioretention areas are shallow stormwater retention facilities designed to mimic forested systems by controlling

More information

2008 SWMM, 2010 Revision City of Tacoma

2008 SWMM, 2010 Revision City of Tacoma 2008 SWMM, 2010 Revision City of Tacoma 2.2.3.1 BMP L630 Rain Gardens Purpose and Definition Bioretention areas are shallow stormwater retention facilities designed to mimic forested systems by controlling

More information

Volume 6 - Low Impact Development. Table of Contents

Volume 6 - Low Impact Development. Table of Contents City of Tacoma Volume 6 - Low Impact Development Table of Contents Purpose of this Volume............................................................6-1 Content and Organization of this Volume..............................................6-1

More information

Public Works Department 104 W. Magnolia Street, Suite 109 Bellingham, WA (360)

Public Works Department 104 W. Magnolia Street, Suite 109 Bellingham, WA (360) Public Works Department 104 W. Magnolia Street, Suite 109 Bellingham, WA 98225 (360) 778-7900 STORMWATER PERMIT SUBMITTAL REQUIREMENTS Most development within the City of Bellingham that involves disruption

More information

5. LOW IMPACT DEVELOPMENT DESIGN STANDARDS

5. LOW IMPACT DEVELOPMENT DESIGN STANDARDS 5. LOW IMPACT DEVELOPMENT DESIGN STANDARDS Low Impact Development (LID) requires a shift in stormwater management away from conveying runoff to a small number of downstream points through hydraulically

More information

THE FOLLOWING IS AN EXCERPT FROM THE 2011 CITY OF SEATTLE STANDARD SPECIFICATIONS WITH MINOR CORRECTIONS MADE TO SECTION 9-03.SEATTLE.

THE FOLLOWING IS AN EXCERPT FROM THE 2011 CITY OF SEATTLE STANDARD SPECIFICATIONS WITH MINOR CORRECTIONS MADE TO SECTION 9-03.SEATTLE. THE FOLLOWING IS AN EXCERPT FROM THE 2011 CITY OF SEATTLE STANDARD SPECIFICATIONS WITH MINOR CORRECTIONS MADE TO SECTION 9-03.2 THE COMPLETE 2011 EDITION MAY BE FOUND AT: HTTP://WWW.SEATTLE.GOV/UTIL/ENGINEERING/STANDARD_PLANS_&_SPECS/INDEX.ASP

More information

The following general requirements will be met for all planter box installations:

The following general requirements will be met for all planter box installations: Greenville County Technical Specification for: WQ-25 PLANTER BOX 1.0 Planter Box 1.1 Description Planter boxes are designed to capture and temporarily store stormwater runoff. Planter Boxes are intended

More information

Chapter 5 - On-Site Storm Water Management

Chapter 5 - On-Site Storm Water Management Chapter 5 - On-Site Storm Water Management Note: Figures 5.1 through 5.5 are courtesy of King County, Figures 5.6 and 5.7 are from Ecology s 1992 Manual, and Figures 5.8 through 5.14 are courtesy of Washington

More information

Appendices: Glossary. General Terms. Specific Terms. Low Impact Development Approaches Handbook

Appendices: Glossary. General Terms. Specific Terms. Low Impact Development Approaches Handbook 67 67 General Terms Specific Terms 66 Low Impact Development Approaches Handbook The vocabulary of low impact development is evolving, and many terms are used interchangeably and to describe the same or

More information

COMMUNITY DEVELOPMENT DEPARTMENT POLICY DRAINAGE FOR RESIDENTIAL PROJECTS WITH ONE OR TWO UNITS REVISED JANUARY 4, 2018

COMMUNITY DEVELOPMENT DEPARTMENT POLICY DRAINAGE FOR RESIDENTIAL PROJECTS WITH ONE OR TWO UNITS REVISED JANUARY 4, 2018 COMMUNITY DEVELOPMENT DEPARTMENT POLICY DRAINAGE FOR RESIDENTIAL PROJECTS WITH ONE OR TWO UNITS REVISED JANUARY 4, 2018 A. California Residential Code Requirement - Construction plans shall indicate how

More information

Structural Stormwater Best Management Practices

Structural Stormwater Best Management Practices Structural Stormwater Best Management Practices for Small Commercial and Residential Applications Timothy Bruno Watershed Manager PA Department of Environmental Protection What are STRUCTURAL BMPs? Physical

More information

4. CONCEPT PLAN DEVELOPMENT

4. CONCEPT PLAN DEVELOPMENT 4. CONCEPT PLAN DEVELOPMENT Concept Plan Step 1: Identify Site Constraints and Opportunities Review the existing site to identify constraints and opportunities for GI Practices to meet the RRv. Constraints

More information

6.1 Bioretention Areas

6.1 Bioretention Areas SAN MATEO COUNTYWIDE WATER POLLUTION PREVENTION PROGRAM 6.1 Bioretention Areas Figure 6-1. Bioretention Area. Source: City of Brisbane Bioretention areas 1, or rain gardens, are concave landscaped areas

More information

SUPPORTING DOCUMENT STORMWATER POLLUTION PREVENTION PLAN (SWPPP) NARRATIVE

SUPPORTING DOCUMENT STORMWATER POLLUTION PREVENTION PLAN (SWPPP) NARRATIVE SUPPORTING DOCUMENT STORMWATER POLLUTION PREVENTION PLAN (SWPPP) NARRATIVE Please complete this narrative form and submit with your SWPPP drawings. Refer to Kitsap County Stormwater Design Manual Vol.

More information

4.5 City of Indianapolis Stormwater Green Infrastructure Guidance: Bioretention (rain gardens) Bioretention Fact Sheet Bioretention Technical Design

4.5 City of Indianapolis Stormwater Green Infrastructure Guidance: Bioretention (rain gardens) Bioretention Fact Sheet Bioretention Technical Design 4.5 City of Indianapolis Stormwater Green Infrastructure Guidance: Bioretention (rain gardens) Bioretention Fact Sheet Bioretention Technical Design Specification Bioretention O & M Manual Draft Green

More information

RAIN GARDEN ILLINOIS URBAN MANUAL PRACTICE STANDARD. (feet) CODE 897 DEFINITION

RAIN GARDEN ILLINOIS URBAN MANUAL PRACTICE STANDARD. (feet) CODE 897 DEFINITION ILLINOIS URBAN MANUAL PRACTICE STANDARD RAIN GARDEN (feet) CODE 897 Source: Kendall County Soil and Water Conservation District DEFINITION Rain gardens are small, shallow, flat bottomed depressions constructed

More information

BIORETENTION FACILITY

BIORETENTION FACILITY ILLINOIS URBAN MANUAL PRACTICE STANDARD BIORETENTION FACILITY (feet) CODE 800 Source: Jessica Cocroft, Winnebago Soil and Water Conservation District DEFINITION Facility that utilizes a soil media, mulch,

More information

Stormwater Management Techniques WMPF LAND USE TRAINING INSTITUTE MARCH 14, 2018

Stormwater Management Techniques WMPF LAND USE TRAINING INSTITUTE MARCH 14, 2018 Stormwater Management Techniques WMPF LAND USE TRAINING INSTITUTE MARCH 14, 2018 Potential Impacts of New Development Urban development can significantly increase stormwater runoff Water quality considerations

More information

Directors Rules for Seattle Municipal Code, Chapters Stormwater Code

Directors Rules for Seattle Municipal Code, Chapters Stormwater Code Directors Rules for Seattle Municipal Code, Chapters 22.800 22.808 Stormwater Code Requirements for Green Stormwater Infrastructure to the Maximum Extent Feasible for Single-Family Residential and Parcel-Based

More information

Key elements : Filter Strips must be designed within parameters required by the Fort Wayne s Development Standards/Criteria Manual.

Key elements : Filter Strips must be designed within parameters required by the Fort Wayne s Development Standards/Criteria Manual. 4.4. Filter Strips Filter Strips are densely vegetated lands that treat sheet flow storm water from adjacent pervious and impervious areas. They function by slowing runoff, trapping sediment and pollutants,

More information

6.2 Flow-Through Planter

6.2 Flow-Through Planter SAN MATEO COUNTYWIDE WATER POLLUTION PREVENTION PROGRAM 6.2 Flow-Through Planter Figure 6-8: At-grade flow-through planter. Source: City of Emeryville Best uses Treating roof runoff Next to buildings Dense

More information

4.6. Low Impact and Retentive Grading

4.6. Low Impact and Retentive Grading 4.6. Low Impact and Retentive Grading Low Impact Grading techniques focus on utilizing existing topography during Site layout to minimize cost. Proposing structures, roads, and other impervious surfaces

More information

ABBREVIATIONS: TABLE OF CONTENTS: REFERENCE MATERIALS: CITY OF SEATTLE COMBINED SEWER OVERFLOW GALLONS PER MINUTE POLYVINYL CHLORIDE SQUARE FEET

ABBREVIATIONS: TABLE OF CONTENTS: REFERENCE MATERIALS: CITY OF SEATTLE COMBINED SEWER OVERFLOW GALLONS PER MINUTE POLYVINYL CHLORIDE SQUARE FEET TABLE OF CONTENTS: ABBREVIATIONS: SHEET NO. A SHEET DESCRIPTION REFERENCE SHEETS TITLE SHEET COS CSO GPM PVC SF CITY OF SEATTLE COMBINED SEWER OVERFLOW GALLONS PER MINUTE POLYVINYL CHLORIDE SQUARE FEET

More information

Table 4.7.1: Swales Potential Application and Storm Water Regulation

Table 4.7.1: Swales Potential Application and Storm Water Regulation 4.7. Swales A swale is a vegetated open channel, planted with a combination of grasses and other herbaceous plants, shrubs, or trees. A traditional swale reduces peak flow at the discharge point by increasing

More information

1. Which of the five checklists in the Municipal Construction Stormwater Site Inspection Toolkit will you use to document this inspection?

1. Which of the five checklists in the Municipal Construction Stormwater Site Inspection Toolkit will you use to document this inspection? GROUP ACTIVITY 2 Municipal Construction Stormwater Site Inspection Toolkit Overview You are a municipal stormwater inspector (Inspector) heading out to inspect a building development site where construction

More information

STORMWATER PERMIT SUBMITTAL REQUIREMENTS

STORMWATER PERMIT SUBMITTAL REQUIREMENTS STORMWATER PERMIT SUBMITTAL REQUIREMENTS Most development within the City of Bellingham that involves disruption of soils, or construction of buildings, streets, parking lots, etc. requires a Stormwater

More information

J. Paul Guyer, P.E., R.A.

J. Paul Guyer, P.E., R.A. J. Paul Guyer, P.E., R.A. Paul Guyer is a registered civil engineer, mechanical engineer, fire protection engineer, and architect with over 35 years experience in the design of buildings and related infrastructure.

More information

PLANNING & DEVELOPMENT SERVICES 1800 Continental Place Mount Vernon, WA Inspections Office Fax

PLANNING & DEVELOPMENT SERVICES 1800 Continental Place Mount Vernon, WA Inspections Office Fax PLANNING & DEVELOPMENT SERVICES 1800 Continental Place Mount Vernon, WA 98273 Inspections 360.336.9306 Office 360.336.9410 Fax 360.336.9416 Application will expire 6 mo from this date: Floodplain Development

More information

State of Rhode Island Stormwater Management Guidance for Individual Single-Family Residential Lot Development

State of Rhode Island Stormwater Management Guidance for Individual Single-Family Residential Lot Development State of Rhode Island Stormwater Management Guidance for Individual Single-Family Residential Lot Development Section 300.6 of the RI Coastal Resources Management Program (RICRMP) and Rule 7.12 of the

More information

Appendix D - Technical Design Criteria for BMPs

Appendix D - Technical Design Criteria for BMPs Appendix D - Technical Design Criteria for BMPs City of Wayzata Page 3 On-site infiltration features Definitions and Scope: Infiltration facilities are constructed basins or depressions located in permeable

More information

Bioretention cell schematic key

Bioretention cell schematic key Bioretention Cells Bioretention cell schematic key 1 3 Hardwood mulch 2 Curb cut 3 18-30 Modified soil 4 Stone aggregate choker layer 5 Stone aggregate base layer 6 Subdrain 7 Undisturbed soil 8 Overflow/Cleanout

More information

County of Prince Edward. Stormwater Management Plan. Agreement in lieu of a Stormwater Management Plan

County of Prince Edward. Stormwater Management Plan. Agreement in lieu of a Stormwater Management Plan County of Prince Edward Stormwater Management Program Date: E-Permitting Number: This stormwater management plan (Agreement) is hereby submitted by the Owner to specify the methods that will be implemented

More information

Technical Guidance for Stormwater Treatment and Site Design Measures

Technical Guidance for Stormwater Treatment and Site Design Measures Chapter 6 Technical Guidance for Stormwater Treatment and Site Design Measures In this Chapter, technical guidance is provided for the stormwater treatment measures allowed by permit requirements as well

More information

Draft Rhode Island Stormwater Design and Installation Standards Manual

Draft Rhode Island Stormwater Design and Installation Standards Manual Draft Rhode Island Stormwater Design and Installation Standards Manual Summary The May 2009 Public Review Draft version of the RI Stormwater Design and Installation Standards Manual consists of approximately

More information

Homeowners Guide to Stormwater BMP Maintenance

Homeowners Guide to Stormwater BMP Maintenance Homeowners Guide to Stormwater BMP Maintenance What You Need to Know to Take Care of Your Property Rain Barrel Dry Well Rain Garden Pervious Asphalt Porous Pavers City of El Monte Stormwater BMP Management

More information

New Development Stormwater Guidelines

New Development Stormwater Guidelines New Development Stormwater Guidelines CITY OF MOUNTLAKE TERRACE Table of Contents Introduction... 2 Ecology s Minimum Requirements for stormwater management... 2 Description of the 9 Minimum Requirements...

More information

Insert Community Name. Homeowner Guide for On-Site Stormwater BMP Maintenance and Care

Insert Community Name. Homeowner Guide for On-Site Stormwater BMP Maintenance and Care Insert Community Name Homeowner Guide for On-Site Stormwater BMP Maintenance and Care Insert Community Name Homeowner Guide for On-Site Stormwater BMP Maintenance and Care Hello! Welcome to the neighborhood.

More information

ABBREVIATIONS. Dwg LID of 1. Abbreviations

ABBREVIATIONS. Dwg LID of 1. Abbreviations ABBREVIATIONS DIA DIAMETER EL ELEVATION FT2 SQUARE FOOT GAL/MIN GALLONS PER MINUTE H HORIZONTAL HDPE HIGH DENSITY POLYETHYLENE HMAC HOT MIX ASPHALT CONCRETE IE INVERT ELEVATION MAX MAXIMUM NO. NUMBER ODEQ

More information

DRAFT DESIGN CRITERIA STORMWATER TREATMENT STANDARDS CITY OF OVERLAND PARK

DRAFT DESIGN CRITERIA STORMWATER TREATMENT STANDARDS CITY OF OVERLAND PARK DRAFT DESIGN CRITERIA STORMWATER TREATMENT STANDARDS CITY OF OVERLAND PARK A. Authority As set forth in the Overland Park Municipal Code (OPMC), Chapter 16.210, the Director of Planning and Development

More information

Attachment 2: Permeable Pavement Design Guidelines

Attachment 2: Permeable Pavement Design Guidelines Attachment 2: Permeable Pavement Design Guidelines Design of permeable pavement systems is critical if they are to function properly and efficiently. The area and shape are dependent on the site design,

More information

Stormwater Control Plan: Small (Tier 1) Land Development Project

Stormwater Control Plan: Small (Tier 1) Land Development Project Stormwater Control Plan: Small (Tier 1) Land Development Project Project ID for Tracking (for City Staff only): The California Regional Water Quality Control Board for the Central Coast Region (Water Board)

More information

Urban Water Management and Soils (ESRM 311 & SEFS 507)

Urban Water Management and Soils (ESRM 311 & SEFS 507) Urban Water Management and Soils (ESRM 311 & SEFS 507) Cougar Mtn Regional Wildland Park & Lakemont Blvd, Bellevue WA Lecture Today Some Urban Water management terms Examples of water management in urban

More information

Appendix I. Checklists

Appendix I. Checklists Appendix I Checklists Town of Greenwich Drainage Manual Department of Public Works - Engineering Division Town Hall - 101 Field Point Road, Greenwich, CT 06836-2540 Phone 203-622-7767 - Fax 203-622-7747

More information

Low Impact Development Practices

Low Impact Development Practices Low Impact Development Practices Michael Dietz, Ph.D. CT Nonpoint Education for Municipal Officials (NEMO) Center for Land Use Education and Research May 8, 2013 Town of Bolton Planning and Zoning Commission

More information

APPENDIX A SIMPLIFIED APPROACH TO STORMWATER MANAGEMENT FOR SMALL PROJECTS. In West Sadsbury Township, Chester County, Pennsylvania

APPENDIX A SIMPLIFIED APPROACH TO STORMWATER MANAGEMENT FOR SMALL PROJECTS. In West Sadsbury Township, Chester County, Pennsylvania APPENDIX A SIMPLIFIED APPROACH TO STORMWATER MANAGEMENT FOR SMALL PROJECTS In West Sadsbury Township, Chester County, Pennsylvania TABLE OF CONTENTS I. Introduction 3 II. Importance of Stormwater Management

More information

Inspection and Maintenance of Stormwater Best Management Practices

Inspection and Maintenance of Stormwater Best Management Practices FAC T S H E E T Inspection and Maintenance of Stormwater Best Management Practices is a general term that refers to vegetated stormwater best management practices (BMPs) that temporarily store rainwater

More information

STORMWATER SITE PLAN INSTRUCTIONS AND SUBMITTAL TEMPLATE Medium and Large Projects

STORMWATER SITE PLAN INSTRUCTIONS AND SUBMITTAL TEMPLATE Medium and Large Projects DEPARTMENT OF COMMUNITY DEVELOPMENT 621 Sheridan Street, Port Townsend, WA 98368 Tel: 360.379.4450 Fax: 360.379.4451 Web: www.co.jefferson.wa.us/communitydevelopment E-mail: dcd@co.jefferson.wa.us STORMWATER

More information

Clallam County Small Project Drainage Requirements And Technical Guidance Manual DRAFT

Clallam County Small Project Drainage Requirements And Technical Guidance Manual DRAFT Clallam County Small Project Drainage Requirements And Technical Guidance Manual DRAFT 2 Small Project Drainage Requirements and Technical Guidance Manual Table of Contents Section I. Section II. Section

More information

A. Install all temporary erosion control measures (in accordance with MNDOT General Conditions 2573) prior to site disturbance.

A. Install all temporary erosion control measures (in accordance with MNDOT General Conditions 2573) prior to site disturbance. The language provided in these specifications is meant to serve as a reminder and provide a generic example of the type of language that should be provided in final construction documents. This language

More information

Post Construction BMPs

Post Construction BMPs Post Construction BMPs Why are Post Construction BMPs important? With increased development brings the increase of impervious cover Parking lots, rooftops, driveways Storm water runoff volume increases

More information

CITY OF TUMWATER 555 ISRAEL RD. SW, TUMWATER, WA (360) (360) (FAX)

CITY OF TUMWATER 555 ISRAEL RD. SW, TUMWATER, WA (360) (360) (FAX) CITY OF TUMWATER 555 ISRAEL RD. SW, TUMWATER, WA 98501 (360) 754-4180 (360) 754-4126 (FAX) Email: cdd@ci.tumwater.wa.us APPENDIX II-C SHORT FORM CONSTRUCTION STORMWATER POLLUTION PREVENTION PLAN (SWPPP)

More information

CHAPTER 9 STORM DRAINAGE. Minimum Requirements for New Development and Redevelopment

CHAPTER 9 STORM DRAINAGE. Minimum Requirements for New Development and Redevelopment CHAPTER 9 STORM DRAINAGE 9.01 General The standards established by this chapter are intended to represent the minimum standards for the design and construction of storm drainage facilities. 9.02 Design

More information

12/31/2014 County of Mendocino s Low Impact Design Standards Manual v1.0 A P P E N D I X 8. Site Design Measures. 32 P a g e

12/31/2014 County of Mendocino s Low Impact Design Standards Manual v1.0 A P P E N D I X 8. Site Design Measures. 32 P a g e 12/31/2014 County of Mendocino s Low Impact Design Standards Manual v1.0 A P P E N D I X 8 Site Design Measures 32 P a g e Rooftop and Impervious Area Disconnection (Self-retaining areas) Description Disconnection

More information

Bioretention. Matt Scharver Northeast Ohio Regional Sewer District. #ProjectCleanLake

Bioretention. Matt Scharver Northeast Ohio Regional Sewer District. #ProjectCleanLake Bioretention Matt Scharver Northeast Ohio Regional Sewer District Stormwater Management Training for MS4 Municipal Employees Training Session Agenda Pre-Training Survey Presentation & Site Visit Post-Training

More information

Development of LID Design Guide in Edmonton

Development of LID Design Guide in Edmonton Development of LID Design Guide in Edmonton Xiangfei Li and Fayi Zhou, the City of Edmonton Dan Healy, AMEC Earth and Environmental Philadelphia LID Symposium September 26, 2011 Outline Why LID Why develop

More information

SUPPORTING DOCUMENT POST-CONSTRUCTION SOIL QUALITY AND DEPTH WORKSHEET

SUPPORTING DOCUMENT POST-CONSTRUCTION SOIL QUALITY AND DEPTH WORKSHEET SUPPTING DOCUMENT POST-CONSTRUCTION SOIL QUALITY AND DEPTH WKSHEET For Department of Ecology Stormwater BMP T5.13 This submittal worksheet will help determine what soil amendments are needed to meet the

More information

Appendix G. Detailed Design

Appendix G. Detailed Design Appendix G Detailed Design G1: Construction details Construction detail drawings usually include important details and specifications for required project design elements. This section provides information

More information

High Point Community: Site Drainage Technical Standards. High Point Community Site Drainage Technical Standards

High Point Community: Site Drainage Technical Standards. High Point Community Site Drainage Technical Standards High Point Community Site Drainage Technical Standards Prepared by SvR Design Company for High Point Community Seattle, Washington 5/2004 Revised 12/2006 101 Acknowledgements: for innovative development

More information

SEATTLE PUBLIC UTILITIES Drainage Design Options for street right of ways.

SEATTLE PUBLIC UTILITIES Drainage Design Options for street right of ways. SEATTLE PUBLIC UTILITIES Drainage Design Options for street right of ways. Numerous ecosystem-based functional stormwater quantity and quality design alternatives are possible within the street ROW. Several

More information

Beyond Rain Gardens Advancing the Use of Compost for Green Infrastructure, Low Impact Development, & Stormwater Management

Beyond Rain Gardens Advancing the Use of Compost for Green Infrastructure, Low Impact Development, & Stormwater Management Beyond Rain Gardens Advancing the Use of Compost for Green Infrastructure, Low Impact Development, & Stormwater Management VORS 2018 Stormwater Management Session 2 Stormwater Management, Green Infrastructure,

More information

SIMPLIFIED APPROACH TO STORMWATER MANAGEMENT FOR SMALL PROJECTS

SIMPLIFIED APPROACH TO STORMWATER MANAGEMENT FOR SMALL PROJECTS SIMPLIFIED APPROACH TO STORMWATER MANAGEMENT FOR SMALL PROJECTS Introduction As required by federal and state law, the Borough of Swarthmore has adopted regulations that affect stormwater runoff and surface

More information

Preparing a Stormwater Control Plan for a Small Land Development Project

Preparing a Stormwater Control Plan for a Small Land Development Project Preparing a Stormwater Control Plan for a Small Land Development Project Addendum to the Stormwater C.3 Guidebook December 1, 2012 Introduction As of December 1, 2012, development projects that create

More information

STORM WATER MANAGEMENT PLAN APPLICATION Manheim Borough

STORM WATER MANAGEMENT PLAN APPLICATION Manheim Borough STORM WATER MANAGEMENT PLAN APPLICATION Manheim Borough DATE Application is hereby made to Manheim Borough for the issuance of a Storm Water Management Plan approval pursuant to the Manheim Borough Storm

More information

Selecting Appropriate Stormwater Control Measures for Your Development Project

Selecting Appropriate Stormwater Control Measures for Your Development Project Phase II Post-Construction Stormwater Requirements Workshop - February 10, 2014 Selecting Appropriate Stormwater Control Measures for Your Development Project Jill Bicknell, P.E., EOA, Inc. Outline of

More information

n1. Design 5.4.6a Urban Bioretention 5.4.6a Urban Bioretention Variations: Planter box, Extended tree pits, Stormwater curb extensions.

n1. Design 5.4.6a Urban Bioretention 5.4.6a Urban Bioretention Variations: Planter box, Extended tree pits, Stormwater curb extensions. 5.4.6a Urban Bioretention Variations: Planter box, Extended tree pits, Stormwater curb extensions. Description: Urban bioretention SCM are similar in function to regular bioretention practices except they

More information

Standard Specifications for Lot-Scale Measures for Small Projects

Standard Specifications for Lot-Scale Measures for Small Projects Appendix K Standard Specifications for Lot-Scale Measures for Small Projects Table of Contents Section K.1 Permit Requirements for Small Projects... K-2 Section K.2 Regional Guidance for Site Design Measures...

More information

Huntington Stormwater Utility

Huntington Stormwater Utility Huntington Stormwater Utility Stormwater Management & Sediment and Erosion Control Requirements for Construction Sites Authorized by Huntington City Code Articles: 971, 970, 930, 935, 955, Revised April

More information

Stormwater Technical Guide

Stormwater Technical Guide Stormwater Technical Guide Compliance with Stormwater Post-Construction Requirements in Santa Barbara County Dan Cloak, Principal Dan Cloak Environmental Consulting January 9, 2014 Introduce yourself Name

More information

FACT SHEET: Pervious Pavement with Infiltration

FACT SHEET: Pervious Pavement with Infiltration FACT SHEET: Pervious Pavement with Infiltration DESCRIPTION Pervious pavement is a Green Infrastructure (GI) technique that combines stormwater infiltration, storage, and structural pavement consisting

More information

INFILTRATION TRENCH - LEAKY PIPE

INFILTRATION TRENCH - LEAKY PIPE INFILTRATION TRENCH - LEAKY PIPE FLOW PERFORATED CMP OR RCP WITH PULLED JOINTS OVERSIZED PIPE (INLINE DETENTION) PERFORATED CMP OR RCP WITH PULLED JOINTS EXFILTRATE TRENCH VOLUME EXFILTRATE SEDIMENT SUMP

More information

West Norriton Township

West Norriton Township West Norriton Township Earth Disturbance and Drainage Permit Application 1630 W. Marshall Street Norristown, PA 19403 Phone: (610) 631-0450 Fax: (610) 630-0304 www.westnorritontwp.org A stormwater permit

More information

Urban Water Management (ESRM 311 & SEFS 507) Cougar Mtn Regional Wildland Park & Lakemont Blvd, Bellevue WA

Urban Water Management (ESRM 311 & SEFS 507) Cougar Mtn Regional Wildland Park & Lakemont Blvd, Bellevue WA Urban Water Management (ESRM 311 & SEFS 507) Cougar Mtn Regional Wildland Park & Lakemont Blvd, Bellevue WA Lecture Today Urban Water management terms Examples of water management in urban areas Field

More information

DEALING WITH STORM WATER MANAGEMENT

DEALING WITH STORM WATER MANAGEMENT December 2012 DEALING WITH STORM WATER MANAGEMENT This fact sheet provides information on the guiding principles of storm water management practices, explains the difference between structural and non-structural

More information

Subsurface Infiltration Bed

Subsurface Infiltration Bed Subsurface Infiltration Bed The Subsurface Infiltration Bed BMP consists of a storage bed underlying either a vegetated or hardscaped surface for the purpose of temporary storage and infiltration of stormwater

More information

BIORETENTION CELLS. Green Infrastructure For Stormwater Management WHAT ARE BIORETENTION CELLS? WHERE ARE BIOCELLS INSTALLED?

BIORETENTION CELLS. Green Infrastructure For Stormwater Management WHAT ARE BIORETENTION CELLS? WHERE ARE BIOCELLS INSTALLED? BIORETENTION CELLS Green Infrastructure For Stormwater Management WHAT ARE BIORETENTION CELLS? Bioretention cells (or biocells) are one of the most widely used green infrastructure practices for managing

More information

Rainwater Management an issue for the 21 st Century. Hydrological Cycle

Rainwater Management an issue for the 21 st Century. Hydrological Cycle Canadian Society of Landscape Architects CONGRESS 2014 Rainwater Management an issue for the 21 st Century Don Crockett, BCSLA, CSLA Principal, Golder Associates Ltd. May 2014 Hydrological Cycle PRE- URBAN

More information

Chapter 14. Stormwater Quality Introduction

Chapter 14. Stormwater Quality Introduction 14.0 Introduction This chapter addresses requirements and design criteria related to post-construction stormwater best management practices (requirements for construction erosion and sediment control are

More information

CHAPTER 11 SITE DESIGN AND LOW IMPACT DEVELOPMENT

CHAPTER 11 SITE DESIGN AND LOW IMPACT DEVELOPMENT CHAPTER 11 SITE DESIGN AND LOW IMPACT DEVELOPMENT Source: City of Bend Chapter Organization 11.1 Purpose... 11-1 11.2 Applicability... 11-1 11.3 Low Impact Development Overview... 11-2 11.3.1 Key Strategies...

More information

SITING CONSIDERATIONS

SITING CONSIDERATIONS Bioretention: Siting and Applications Presentation Overview Siting Considerations Native Soil Characterization Lessons Leaned Feasibility & Performance Applications ALICE LANCASTER, PE alancaster@herrerainc.com

More information

Types and Basic Design of Post-Construction BMPs

Types and Basic Design of Post-Construction BMPs Types and Basic Design of Post-Construction BMPs F O R R E S I D E N T I A L L A N D S C A P E R S D A N B O G O E V S K I O H I O E P A N O R T H E A S T D I S T R I C T O F F I C E J U L Y 9, 2 0 1 3

More information

Kittson Parkway / Watershed Park Parking Lot

Kittson Parkway / Watershed Park Parking Lot Kittson Parkway / Watershed Park Parking Lot Date Constructed: Summer 2005 Site Location / Description: Kittson Parkway, North Delta, British Columbia. Permeable parking lot adjacent to Watershed Park;

More information

SMALL PROJECTS SIMPLIFIED APPROACH

SMALL PROJECTS SIMPLIFIED APPROACH SMALL PROJECT APPLICATION AND STORMWATER MANAGEMENT DESIGN ASSISTANCE MANUAL FOR SMALL PROJECTS IN FULTON TOWNSHIP LANCASTER COUNTY, PENNSYLVANIA SMALL PROJECTS SIMPLIFIED APPROACH Prepared By: Light-Heigel

More information

Best Development Practices

Best Development Practices Town of Winchendon E. Himlan, Mass. Watershed Coalition Berkshire Design Group Best Development Practices Version 1, March 2010 Guidebook Table of Contents INTRODUCTION... 1 I. CHECKLIST FOR DESIGNERS...

More information

BMP Suitability Matrix

BMP Suitability Matrix Green Infrastructure Across the Urban to Rural Spectrum Guidance document for how to use the BMP Suitability Matrix. BMP Suitability Matrix A User s Guide to Green Infrastructure Best Management Practices

More information

Placement of the soil should be in lifts of mm and loosely compacted (tamped lightly with a backhoe bucket).

Placement of the soil should be in lifts of mm and loosely compacted (tamped lightly with a backhoe bucket). 6 Rain Gardens Rain Gardens 6.1 Introduction A rain garden is used to attenuate peak flows and to provide stormwater treatment. Rain gardens use the concept of bioretention, a water quality practice in

More information

Before you build: Locating and Planning

Before you build: Locating and Planning Before you build: Locating and Planning a Rain Garden David McDonald, Seattle Public Utilities Installing Rain Gardens & Cisterns Trainings for contractors 11/3/2011 www.seattle.gov/util/rainwise Runoff

More information

Chapter 1 Introduction

Chapter 1 Introduction Chapter 1 Introduction Bioretention systems, also known as biofiltration systems, biofilter or rain gardens, is a common stormwater mitigation measure. It utilises a low energy consumption treatment technology

More information

Urban Watershed Mentors

Urban Watershed Mentors Urban Watershed Mentors Bureau of Environmental Services Josh Robben Urban Stormwater background Stormwater retrofits Site assessment Design considerations Maintenance considerations Resources/programs

More information

Structural Storm Water Best Management Practices (BMPs)

Structural Storm Water Best Management Practices (BMPs) Structural Storm Water Best Management Practices (BMPs) Storm Water Permitting: The SWPPP Revealed By Deron Austin, PE January 11, 2006 3:30-5:00 PM Orlando, Florida Presentation Outline Preface About

More information

Green City, Clean Waters

Green City, Clean Waters Green City, Clean Waters Green Infrastructure Maintenance Manual Consent Order & Agreement Deliverable VIII City of Philadelphia Combined Sewer Overflow Long Term Control Plan Update Submitted to The Commonwealth

More information

Table of Contents. Preface... xv

Table of Contents. Preface... xv Table of Contents Preface... xv Objective... xv Organization of this Manual...xvi How to Use this Manual...xvii Development of Best Management Practices (BMPs) for Stormwater Management...xviii Best Management

More information

Stormwater Drainage Assessment For Single Family Residence

Stormwater Drainage Assessment For Single Family Residence Stormwater Drainage Assessment For Single Family Residence Project Name: SEADER SFD Project Address: 2301 NE Perkins Way, Lake Forest Park, King County WA. Parcel Number(s): Tax Parcel No. 86659-00181

More information

WQ-07 INFILTRATION TRENCH

WQ-07 INFILTRATION TRENCH Greenville County Technical Specification for: WQ-07 INFILTRATION TRENCH 1.0 Infiltration Trench 1.1 Description Infiltration Trenches are excavations filled with stone to create an underground reservoir

More information

Urban Conservation Practice Physical Effects ESTABLISHMENT, GROWTH, AND HARVEST NUTRIENT MANAGEMENT

Urban Conservation Practice Physical Effects ESTABLISHMENT, GROWTH, AND HARVEST NUTRIENT MANAGEMENT NOT WELL 800 - Urban Stormwater Wetlands A constructed system of shallow pools that create growing conditions for wetland plants to lessen the impacts of stormwater quality and quantity in urban areas.

More information

PAVING PARKING AREAS AND ROADS DESCRIPTION. Alternate Names: Pavement Practices, Impervious Paving

PAVING PARKING AREAS AND ROADS DESCRIPTION. Alternate Names: Pavement Practices, Impervious Paving 4.2-i PAVING PARKING AREAS AND ROADS Alternate Names: Pavement Practices, Impervious Paving DESCRIPTION All roads, driveways, and parking lots proposed for year-round use shall be paved with a hard plowable

More information

Use of Best Management Practices

Use of Best Management Practices Use of Best Management Practices Presented at the ANJEC Flood Hazard Workshop Bordentown, NJ March 13, 2008 Stormwater BMPs "a technique, measure or structural control that is used for a given set of conditions

More information

Small Project Guidance Document

Small Project Guidance Document Small Project Guidance Document Introduction If you are considering a relatively small construction project on your property that creates new impervious area and you need to manage the stormwater that

More information

Lesson 2: Stormwater Best Management Practices (BMPs)

Lesson 2: Stormwater Best Management Practices (BMPs) Lesson 2: Stormwater Best Management Practices (BMPs) Environmental Stewards Class Christopher C. Obropta, Ph.D., P.E. Extension Specialist in Water Resources 732-932-9800 ext. 6209 obropta@envsci.rutgers.edu

More information

MANUAL OF DESIGN, INSTALLATION, AND MAINTENANCE REQUIREMENTS FOR STORMWATER MANAGEMENT PLANS

MANUAL OF DESIGN, INSTALLATION, AND MAINTENANCE REQUIREMENTS FOR STORMWATER MANAGEMENT PLANS MANUAL OF DESIGN, INSTALLATION, AND MAINTENANCE REQUIREMENTS FOR STORMWATER MANAGEMENT PLANS May 2007 SECTION 1 Responsibility of Applicant TABLE OF CONTENTS A. Stormwater Management Plan Required Information

More information

WQ-23 MOUNTAINOUS AND STEEP SLOPE SITES

WQ-23 MOUNTAINOUS AND STEEP SLOPE SITES Greenville County Technical Specification for: WQ-23 MOUNTAINOUS AND STEEP SLOPE SITES 1.0 Mountainous and Steep Slope Sites 1.1 Description The geographic locations of portions of Greenville County are

More information