Chapter 5 Heat-transfer Equipment
|
|
- Samson Powell
- 5 years ago
- Views:
Transcription
1 Chapter 5 Heat-transfer Equipment
2 1. Condenser Four condenser configurations are possible: 1. Horizontal, with condensation in the shell, and the cooling medium in the tubes. 2. Horizontal, with condensation in the tubes. 3. Vertical, with condensation in the shell. 4. Vertical, with condensation in the tubes. Horizontal shell-side and vertical tube-side are the most commonly used types of condenser. A horizontal exchanger with condensation in the tubes is rarely used as a process condenser, but is the usual arrangement for heaters and vaporizers using condensing steam as the heating medium.
3 1. Condensation outside horizontal tubes
4 1. Condensation outside horizontal tubes In a bank of tubes the condensate from the upper rows of tubes will add to that condensing on the lower tubes. If there are N r tubes in a vertical row and the condensate is assumed to flow smoothly from row to row, Figure 12.42a, and if the flow remains laminar, the mean coefficient predicted by the Nusselt model is related to that for the top tube by: In practice, the condensate will not flow smoothly from tube to tube, Figure 12.42b, and the factor of Nr -1/4 applied to the single tube coefficient in equation is considered to be too conservative. Based on results from commercial exchangers, Kern (1950) suggests using an index of 1/6. Frank (1978) suggests multiplying single tube coefficient by a factor of 0.75.
5 1. Condensation outside horizontal tubes
6 1. Condensation outside horizontal tubes Using Kern s method, the mean coefficient for a tube bundle is given by: For low-viscosity condensates the correction for the number of tube rows is generally ignored. A procedure for estimating the shell-side heat transfer in horizontal condensers is given in the Engineering Sciences Data Unit Design Guide, ESDU
7 2. Condensation inside and outside vertical tubes For condensation inside and outside vertical tubes the Nusselt model gives: For a tube bundle: Equation will apply up to a Reynolds number of 30; above this value waves on the condensate film become important. The Reynolds number for the condensate film is given by:
8 2. Condensation inside and outside vertical tubes Above a Reynolds number of around 2000, the condensate film becomes turbulent. The effect of turbulence in the condensate film was investigated by Colburn (1934) and Colburn s results are generally used for condenser design, Figure Equation is also shown on Figure The Prandtl number for the condensate film is given by:
9 Figure can be used to estimate condensate film coefficients in the absence of appreciable vapor shear. Horizontal and downward vertical vapor flow will increase the rate of heat transfer, and the use of Figure will give conservative values for most practical condenser designs. Boyko and Kruzhilin (1967) developed a correlation for shear-controlled condensation in tubes which is simple to use. Their correlation gives the mean coefficient between two points at which the vapor quality is known. The vapor quality x is the mass fraction of the vapor present. It is convenient to represent the Boyko-Kruzhilin correlation as: Where: and the suffixes 1 and 2 refer to the inlet and outlet conditions respectively. h' i is the tubeside coefficient evaluated for single-phase flow of the total condensate (the condensate at point 2).
10 Boyko and Kruzhilin used the correlation: In a condenser the inlet stream will normally be saturated vapor and the vapor will be totally condensed. For these conditions equation becomes: For the design of condensers with condensation inside the tubes and downward vapor flow, the coefficient should be evaluated using Figure and equation 12.52, and the higher value selected.
11 Example Estimate the heat-transfer coefficient for steam condensing on the outside, and on the inside, of a 25 mm o.d., 21 mm i.d. vertical tube 3.66 m long. The steam condensate rate is kg/s per tube and condensation takes place at 3 bar. The steam will flow down the tube. Solution Physical properties, from steam tables:
12 vertical tube loading
13
14
15 Example It is proposed to use an existing distillation column, which is fitted with a dephlegmator (reflux condenser) which has 200 vertical, 50 mm i.d., tubes, for separating benzene from a mixture of chlorobenzenes. The top product will be 2500 kg/h benzene and the column will operate with a reflux ratio of 3. Check if the tubes are likely to flood. The condenser pressure will be 1 bar. Solution The vapor will flow up and the liquid down the tubes. The maximum flow rates of both will occur at the base of the tube.
16 Tubes should not flood, but there is little margin of safety.
17 Example Design a condenser for the following duty: 45,000 kg/h of mixed light hydrocarbon vapors to be condensed. The condenser to operate at 10 bar. The vapor will enter the condenser saturated at 60 C and the condensation will be complete at 45 C. The average molecular weight of the vapors is 52. The enthalpy of the vapor is kj/kg and the condensate kj/kg. Cooling water is available at 30 C and the temperature rise is to be limited to 10 C. Plant standards require tubes of 20 mm o.d., 16.8 mm i.d., 4.88 m (16 ft) long, of admiralty. The vapors are to be totally condensed and no sub-cooling is required. Solution Only the thermal design will be done. The physical properties of the mixture will be taken as the mean of those for n-propane (MW = 44) and n-butane (MW = 58), at the average temperature.
18 Assumed overall coefficient (Table 12.1) = 900 W/m 2 C Mean temperature difference: the condensation range is small and the change in saturation temperature will be linear, so the corrected logarithmic mean temperature difference can be used.
19 Try a horizontal exchanger, condensation in the shell, four tube passes. For one shell pass, four tube passes, from Figure 12.19, F t = 0.92.
20
21
22
23 Significantly lower than the assumed value of 900 W/m 2 C. Repeat calculation using new trial value of 750 W/m 2 C.
24 Close enough to estimate, firm up design.
25 Shell-side pressure drop Use pull-through floating head, no need for close clearance. Select baffle spacing = shell diameter, 45 per cent cut. From Figure 12.10, clearance =95 mm.
26
27 Shell-side pressure drop Negligible; more sophisticated method of calculation not justified.
28 Tube-side pressure drop acceptable.
Evaporation System: Types and Design Aspects
Evaporation System: Types and Design Aspects Dr. Pankaj Kumar, Er. Dhritiman Saha and Er. Chandan Solanki Food Grains and Oil Seeds Processing Division, ICAR-CIPHET, Ludhiana Evaporation is an important
More information2. HEAT EXCHANGERS MESA
1. INTRODUCTION Multiport minichannel and microchannel aluminium tubes are becoming more popular as components in heat exchangers. These heat exchangers are used in various industrial applications and
More informationHeat Exchangers. Heat Exchangers 1
Heat Exchangers Heat Exchangers 1 How is the heat transfer? Mechanism of Convection Applications. Mean fluid Velocity and Boundary and their effect on the rate of heat transfer. Fundamental equation of
More information2. PROCESS DESIGN OF SHELL AND TUBE EXCHANGER FOR TWO PHASE HEAT TRANSFER
he required heat transfer area (where, n t =335): A 1 d L n = π 24 335=2105 ft 2 12 reqd o t t % Overdesign =9.8% which is within the acceptable limit. Refer module # 2 for the mechanical design of shell
More informationGandhinagar Institute of Technology Mechanical Engineering (Thermal Engineering) Semester II. Design of Heat Exchange Equipments [ ]
Experiment 1 Study of fundamentals of Fluid Flow and Heat Transfer associated with Heat Exchangers Review questions (1) Significance of dimensionless numbers. (2) Define overall heat transfer coefficient.
More informationScientific Principals and Analytical Model. Charcoal Cooler. Lisa Crofoot MECH 425, Queens University
Scientific Principals and Analytical Model Charcoal Cooler Lisa Crofoot MECH 425, Queens University 1.0 Scientific Principles Evaporative cooling is based on the principle that water requires heat energy
More informationAll rights reserved, Armando B. Corripio, PhD, PE, Solid Dryer Design Introduction Continuous Dryer Design...
Solid Dryer Design All rights reserved, Armando B. Corripio, PhD, PE, 2014 Contents Solid Dryer Design... 1 Introduction... 2 1. Continuous Dryer Design... 3 1.1 Mass Balances... 4 1.2 Temperature Profiles...
More informationMechanical Engineering Department Sheet (1)
Benha University Heat and Mass Transfer Faculty of Engineering at Shoubra 3 rd Year (Power) Mechanical Engineering Department Sheet (1) (1) What is heat exchanger? Mention with brief description and sketches
More informationHeat Transfer Equipments
Heat Transfer Equipments The transfer of heat to and from process fluid is an essential part of most chemical processes. The word exchanger really applies to all types of equipments in which heat is exchanged.
More informationHeat exchangers are devices that facilitate the exchange of heat between
cen58933_ch3.qxd 9/9/2002 9:57 AM Page 667 HEAT EXCHANGERS CHAPTER 3 Heat exchangers are devices that facilitate the exchange of heat between two fluids that are at different temperatures while keeping
More informationExperimental Investigation of Tube Configuration for a Surface Condenser
Experimental Investigation of Tube Configuration for a Surface Condenser Shrikant Subhash Chaudhari 1, T Mahender 2, Subramanyam Pavuluri 3 PG Student, Department of Mechanical Engineering, MLR Institute
More informationHow is the heat transfer?
How is the heat transfer? As we discussed early in the first chapter that heat can transfer through materials and the surrounding medium whenever temperature gradient exists until thermal equilibrium is
More informationFS 231: Final Exam (5-6-05) Part A (Closed Book): 60 points
Name: Start time: End time: FS 231: Final Exam (5-6-05) Part A (Closed Book): 60 points 1. What are the units of the following quantities? (10 points) a. Enthalpy of a refrigerant b. Dryness fraction of
More informationChapter 10. Refrigeration and Heat Pump Systems
Chapter 10 Refrigeration and Heat Pump Systems Learning Outcomes Demonstrate understanding of basic vaporcompression refrigeration and heat pump systems. Develop and analyze thermodynamic models of vapor-compression
More informationijcrr Vol 04 issue 07 Category: Research Received on:06/02/12 Revised on:17/02/12 Accepted on:02/03/12
EXPERIMENTAL ANALYSIS OF THE EFFECT OF FIN GEOMETRY ON HEAT TRANSFER RATE THROUGH THE REFRIGERATOR CONDENSER ijcrr Vol 04 issue 07 Category: Research Received on:06/02/12 Revised on:17/02/12 Accepted on:02/03/12
More informationFalling Film Heat Exchangers for Solar Water Heaters
Y.C., G.L. Morrison and M. Behnia School of Mechanical and Manufacturing Engineering University of New South Wales Sydney 2052 AUSTRALIA E-mail: yens@student.unsw.edu.au Abstract The characteristics of
More informationThe Condensate Water Systems
The Condensate Water Systems Condenser: A closed vessel in which steam is condensed by abstracting the heat and where the pressure is maintained below atmospheric pressure is known as a condenser. The
More informationThermal Design of Condenser Using Ecofriendly Refrigerants R404A-R508B for Cascade Refrigeration System
Thermal Design of Condenser Using Ecofriendly Refrigerants R404A-R508B for Cascade Refrigeration System A D Parekh, and P R Tailor Abstract Because of damaging effect of CFC refrigerants on stratospheric
More informationDesign Based Comparative Study of Several Condensers Komal B. Dabhi 1, Prof. S. B. Thakore 2 1 Chemical Engg. Dept., L. D. College of Engineering, Ahmedabad 380015 2 Chemical Engg. Dept., L. D. College
More informationAs we discussed early in the first chapter that heat can transfer through materials and the surrounding medium whenever temperature gradient exists
As we discussed early in the first chapter that heat can transfer through materials and the surrounding medium whenever temperature gradient exists until thermal equilibrium is reached. Heat transfer by:
More informationRefinery Vacuum Towers. State of the Art. (Extended Abstract)
Paper 357b Refinery Vacuum Towers State of the Art (Extended Abstract) Andrew W. Sloley CH2M HILL 21 Bellwether Way, Unit 111 Bellingham, WA 98225 Prepared for Presentation at the American Institute of
More informationHEFAT th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics Sun City, South Africa Paper number:pp1
HEFAT27 5 th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics Sun City, South Africa Paper number:pp PERFORMANCE ANALYSIS OF AIR-COOLED CONDENSER USING MICRO-FIN TUBES P.A.Patil
More informationCHAPTER 8 EVAPORATION. The basic factors that affect the rate of evaporation are the:
CHAPTER 8 EVAPORATION Frequently in the food industry a raw material or a processed food contains more water than is required in the final product. When the foodstuff is a liquid, the easiest method of
More informationIn the name of God. Jami Institute of Jami - Mehdi Rasti
In the name of God 1 Heat Transfer Jami Institute of Technology Heat Exchangers part 2 Mehdi Rasti 2 The Counter-Flow Heat Exchanger In contrast to the parallel-flow exchanger, this configuration provides
More informationHomework Chapter2. Homework Chapter3
Homework Chapter2 2/1 A storage tank holds methane at 120 K, with a quality of 25 %, and it warms up by 5 C per hour due to a failure in the refrigeration system. How long time will it take before the
More informationTechniques of Heat Transfer Enhancement and their Application. Chapter 4. Performance Evaluation Criteria for Two-Phase Heat Exchangers
Chapter 4 Performance Evaluation Criteria for Two-Phase Heat Exchangers Prof. Min Zeng 1/50 1. Introduction 2. Operating Characteristics of Two-phase Heat Exchangers 3. Enhancement in Two-Phase Heat Exchange
More informationSome Heat Transfer Problems. A hydrocarbon oil (mean heat capacity = 0.50 BTU/(lb m
CM0 Transport I Part II: Heat Transfer Exam Review: Some Heat Transfer Problems Professor Faith Morrison Department of Chemical Engineering Michigan Technological University Example : A hydrocarbon oil
More informationDue to its low temperature glide about 1.5 approx. (75% less than R-407C and R-427A), it is suitable for a wide range of applications.
TECHNICAL DATA SHEET R434A () Features and uses of R-434A () is a non-flammable HFC mixture. ODP = 0, compatible with traditional mineral lubricants, alkyl benzene and also with synthetic POE, so there
More informationSteam Power Cycles Part II
Steam Power Cycles Part II Regenerative Cycles - Open and Closed Feedwater Heaters One approach to increasing the efficiency of steam power cycle is by extracting some of the steam from various stages
More informationCHAPTER 7 COMPARISON OF HEAT EXCHANGERS
168 CHAPTER 7 COMPARISON OF HEAT EXCHANGERS Heat exchangers may be classified according to their flow arrangement. In parallel flow heat exchangers, the two fluids enter the exchanger at the same end,
More informationJurnal UMP Social Sciences and Technology Management Vol. 3, Issue. 3,2015
The Design of a Heat Exchanger Shell - Tube as Evaporator an Absorption Chiller Cycle to Reduce the Temperature of the Air Entering Diesel Engine Heavy Loads 75% And 50% of the Engine Part Seyyede Sepideh
More informationFor an ideal gas mixture, Dalton s law states that the sum of the partial pressures of the individual components is equal to the total pressure.
1 PSYCHROMETICS Psychrometry is the study of the characteristics of moist air. We will see soon that evaporation of moisture from the skin can have a significant impact on thermal comfort. The rate of
More informationExperimental Investigation Of A New Low- Approach Evaporator With Reduced Refrigerant Charge
Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2018 Experimental Investigation Of A New Low- Approach Evaporator With Reduced
More informationPhysical Mechanism of Convection. Conduction and convection are similar in that both mechanisms require the presence of a material medium.
Convection 1 Physical Mechanism of Convection Conduction and convection are similar in that both mechanisms require the presence of a material medium. But they are different in that convection requires
More informationTHE GATE COACH All Rights Reserved 28, Jia Sarai N.Delhi-16, ,-9998
1 P a g e 1 BASIC CONCEPTS IN HEAT TRANSFER Introduction 3 Thermodynamics vs Heat transfer 4 Essential conditions for heat transfer 4 Heat transfer mechanism 4 Thermal conductivity 7 2 CONDUCTION Steady
More informationSeyedeh Sepideh Ghaffari 1 & Seyed Ali Jazayeri 2
Modern Applied Science; Vol. 9, No. 13; 2015 ISSN 1913-1844 E-ISSN 1913-1852 Published by Canadian Center of Science and Education The Design of a Shell-Tube Heat Exchanger as Evaporator an Absorption
More informationChapter 14, Problem 27.
Chapter 14, Problem 27. A house contains air at 25 C and 65 percent relative humidity. Will any moisture condense on the inner surfaces of the windows when the temperature of the window drops to 10 C?
More informationThermodynamics: Homework A Set 7 Jennifer West (2004)
Thermodynamics: Homework A Set 7 Jennifer West (2004) Problem 1 Water is the working fluid in a Carnot vapor power cycle. Saturated liquid enters the boiler at a pressure of 18 MPa, and saturated vapor
More information[Vali*, 5(2): February, 2016] ISSN: (I2OR), Publication Impact Factor: 3.785
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY PERFORMANCE ANALYSIS OF VCR SYSTEM WITH VARYING THE DIAMETERS OF HELICAL CONDENSER COIL BY USING R-134A REFRIGERANT R.Hussain
More informationHomework #4 (group) Tuesday, 27 by 4:00 pm 5290 exercises (individual) Tuesday, 27 by 4:00 pm extra credit (individual) Tuesday, 27 by 4:00 pm
Homework #4 (group) Tuesday, 27 by 4:00 pm 5290 exercises (individual) Tuesday, 27 by 4:00 pm extra credit (individual) Tuesday, 27 by 4:00 pm Readings for this homework assignment and upcoming lectures
More informationA STUDY ON COMPACT HEAT EXCHANGERS AND PERFORMANCE ANALYSIS
A STUDY ON COMPACT HEAT EXCHANGERS AND PERFORMANCE ANALYSIS V. BHOGESWARA RAO Research Scholar Email:pallivayala@gmail.com Dr. S. CHAKRADHAR GOUD Principal, Sri Sarada Institute of Science and Technology
More informationENSC 388: Engineering Thermodynamics and Heat Transfer
ENSC 388: Engineering Thermodynamics and Heat Transfer Experiment 3: Free and Forced Convection Objective Determination of heat transfer coefficient for free and forced convection for different geometries.
More informationME Mechanical Engineering Systems Laboratory. Experiment 3 - Mass and Energy Balances in Psychrometric Processes
ME 410 - Mechanical Engineering Systems Laboratory Experiment 3 - Mass and Energy Balances in Psychrometric Processes Assist.Prof.Dr. Özgür BAYER, A-123 AIR-CONDITIONING (A/C) Goal: Control temperature
More informationExperimental study on heat transfer characteristics of horizontal concentric tube using twisted wire brush inserts
International Journal of Current Engineering and Technology E-ISSN 2277 416, P-ISSN 2347 5161 216 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Experimental
More informationModelling of divided wall column
CHEMICAL ENGINEERING TRANSACTIONS Volume 21, 2010 Editor J. J. Klemeš, H. L. Lam, P. S. Varbanov Copyright 2010, AIDIC Servizi S.r.l., ISBN 978-88-95608-05-1 ISSN 1974-9791 DOI: 10.3303/CET1021012 67 Modelling
More informationIntegral effects 567 Iron oxide deposition 462. Kettle Reboiler Modelling 732
1093 Index Acceleration pressure drop 575, 578 Access lanes 844 Accuracy ofpost-chf correlations 558 Actual stearn quality 558 Additives for liquids 344 Aging offouling deposits 418 Air Cooled Heat Exchangers
More informationLecture # 5: SOLVED PROBLEM
Lecture # 5: SOLVED PROBLEM Example.3: (Mechanical Design) The drier has a uniform temperature of around 150 o C at any point of time (working pressure in the drier is 0.1013 N/mm ). So the material used
More informationRS-70 is suitable as a direct replacement for R-22 in low, medium and high temperatures in a great number of applications:
TECHNICAL DATA SHEET Features and uses of is a non-azeotropic blend of HFC with zero Ozone Depletion Potential et low Global Warming Potential (GWP), formulated to meet the requirements of the F-Gas Regulation
More informationHEAT EXCHANGER FORMULAS & EXAMPLE
Formulas for Heat Exchanger System using a Modulating Control Valve Definition of Terms and Units: E = Mean Heat Transfer Rate or Heat Load (Btu/hr) E D = Design Heat Load (Btu/hr) U = Overall Heat Transfer
More informationModeling of a regenerative indirect evaporative cooler for a desiccant cooling system
Downloaded from orbit.dtu.dk on: Jun 29, 2018 Modeling of a regenerative indirect evaporative cooler for a desiccant cooling system Bellemo, Lorenzo; Elmegaard, Brian; Reinholdt, Lars O. ; Kærn, Martin
More informationSubscripts 1-4 States of the given system Comp Compressor Cond Condenser E Evaporator vol Volumetric G Gas L Liquid
Simulation Analysis of Compression Refrigeration Cycle with Different Refrigerants P.Thangavel, Dr.P.Somasundaram, T.Sivakumar, C.Selva Kumar, G.Vetriselvan Abstract --- In this analysis, the performance
More informationHeat transfer property of refrigerant-oil mixture in a flooded evaporator: The role of bubble formation and oil retention
Korean J. Chem. Eng., 30(5), 1029-1033 (2013) DOI: 10.1007/s11814-013-0024-9 INVITED REVIEW PAPER Heat transfer property of refrigerant-oil mixture in a flooded evaporator: The role of bubble formation
More informationTROUBLESHOOT PACKING MALDISTRIBUTION UPSET PART 2: BOILING AND FLASHING IN PACKED TOWER DISTRIBUTORS
TROUBLESHOOT PACKING MALDISTRIBUTION UPSET PART 2: BOILING AND FLASHING IN PACKED TOWER DISTRIBUTORS Henry Z. Kister, Walter J. Stupin and Jelle Ernst Oude Lenferink Fluor Corp., 3 Polaris Way, Aliso Viejo,
More informationExperimental Investigation of Elliptical Tube Bank Cross Flow Heat Exchanger with Inline Arrangement & 45 Angle of Attack
Experimental Investigation of Elliptical Tube Bank Cross Flow Heat Exchanger with Inline Arrangement & 45 Angle of Attack #1 Digvijay A. Shelar, #2 N.S. Gohel, #3 R. S. Jha #1 Mechanical Engineering Department,
More informations. Properties for R134a are as follows : Saturated R-134a Superheated R-134a
CHAPTER 9 REFRIGERATION & AIR-CONDITIONING YEAR 2012 ONE MARK Common Data For Q. 1 and Q.2 A refrigerator operates between 120 kpa and 800 kpa in an ideal vapour compression cycle with R-134a as the refrigerant.
More informationFig.: macroscopic kinetic energy is an organized form of energy and is much more useful
Harnessing Energy Fig.: macroscopic kinetic energy is an organized form of energy and is much more useful Vapor Power Cycle The vast majority of electrical generating plants are variations of vapor power
More informationEfficiency of Application the Condensing Heat Utilizers in the Existing Boiler's Unit in Heat Power Station
Efficiency of Application the Condensing Heat Utilizers in the Existing Boiler's Unit in Heat Power Station Normuminov J.A. Assistant, Dean of Heat Power Engineering, Tashkent State Technical University,
More informationPressure Enthalpy Charts
Pressure Enthalpy Charts What is a p-h Diagram? A p-h diagram is a diagram with a vertical axis of absolute pressure and a horizontal axis of specific enthalpy. "Enthalpy is the amount of energy in a substance
More informationShalaby Institute of Fire Protection Heyrothsberge, Germany.
International Water Mist Conference November 3-4, 2010, Prague, Czech Republic The Influence of Droplet Size of Water Mist on Extinguishment Fire Plume Dr.Hemdan Shalaby Institute of Fire Protection Heyrothsberge,
More informationExperimental Measurement of Water Evaporation Rates Into Air and Superheated Steam
M. Haji Dept. of Mechanical Engineering, Washington State University, Pullman, WA 99164 L. C. Chow Dept. of Mechanical Engineering, University of Kentucky, Lexington, KY 40506 Experimental Measurement
More informationJ. LINES, Graham Corp., Batavia, New York
Originally appeared in: January 2017, pgs 77-81. Used with permission. Process Engineering J. LINES, Graham Corp., Batavia, New York Key design considerations for vacuum process condensers The crude oil
More informationRole of Nano-technology for improving of thermal performances of vapour compression refrigeration system (VCRS): An Overview
International Journal of Research in Engineering and Innovation Vol-2, Issue-1 (2018), 21-28 International Journal of Research in Engineering and Innovation (IJREI) journal home page: http://www.ijrei.com
More informationIntroduction to Material and Energy Balance
Subject Name Paper Name Module Name/Title Module Id Pre-requisites Objectives Keywords Description of Module Food Technology Unit Operations in Food Processing Introduction to material and energy balance
More informationThere are a number of factors in a process which may result in liquid entrainment. Some of the commonly observed causes are discussed below.
MIST ELIMINATORS MIST ELIMINATION In the chemical process industry there are a number of processes where gases and liquids come into contact with each other and whenever this happens the gas will entrain
More informationEXPERIMENTAL INVESTIGATIONS ON AUTOMOBILE AIR CONDITIONERS WORKING WITH R134a AND R290/R600a AS AN ALTERNATIVE
Karthikeyan, K. et al.: Experimental Investigations on Automobile Air S515 EXPERIMENTAL INVESTIGATIONS ON AUTOMOBILE AIR CONDITIONERS WORKING WITH R134a AND R290/R600a AS AN ALTERNATIVE by Karthikeyan
More informationPerformance Enhancement of Refrigeration Cycle by Employing a Heat Exchanger
Performance Enhancement of Refrigeration Cycle by Employing a Heat Exchanger Abstract Shoeb J. Inamdar 1 H.S. Farkade 2 M. Tech student. (Thermal Engineering) 1, Asst. Professor 2 Department of Mechanical
More informationSIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road AUTONOMOUS QUESTION BANK (DESCRIPTIVE) UNIT I
SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 AUTONOMOUS QUESTION BANK (DESCRIPTIVE) Subject with Code : Refrigeration and Air Conditioning (16ME8806) Course & Branch:
More informationMECHANICAL ENGINEERING ME.2017 FUNDAMENTAL OF REFRIGERATION AND AIR CONDITIONING. Sample Questions and Answers
MECHANICAL ENGINEERING ME.2017 FUNDAMENTAL OF REFRIGERATION AND AIR CONDITIONING Sample Questions and Answers CHAPTER 5 EVAPORATORS 1. What is Evaporator? Classify the various types of evaporator. Evaporator
More informationEXPERIMENTAL EVALUATION OF CONDENSATION HEAT TRANSFER COEFFICIENT OF R-417A IN HORIZONTAL TUBES
112 Military Technical College Kobry El-Kobbah, Cairo, Egypt. 17 th International Conference on Applied Mechanics and Mechanical Engineering. EXPERIMENTAL EVALUATION OF CONDENSATION HEAT TRANSFER COEFFICIENT
More informationHeat Exchanger. The purpose may be either to remove heat from a fluid or to add heat to a fluid.
HEAT EXCHANGERS Heat Exchanger Heat exchanger is an apparatus or an equipment in which the process of heating or cooling occurs. The heat is transferred from one fluid being heated to another fluid being
More informationYogesh B Desale, J. H. Bhangale. Abstract
International Engineering Research Journal Experimental & Investigation of Atmospheric Water Generation by using Vapour Compression system with Subcooling Yogesh B Desale, J. H. Bhangale MechanicalDepartment,
More informationInternational Association of Certified Practicing Engineers
www.iacpe.com Knowledge, Certification, Networking Page: 1 51 IACPE No 19, Jalan Bilal Mahmood 80100 Johor Bahru Malaysia The International is providing the introduction to the Training Module for your
More informationSteam Site Guide. Steam Site Guide. Heat Exchange Applications - SI Units
Steam Site Guide Steam Site Guide Heat Exchange Applications - SI Units Steam Site Guide Content Introduction... 03 01. Estimating Steam Loads... 04 02. Steam Table SI... 07 03. Sizing a Steam Pipe...
More informationInvestigation of Multiple Effect Evaporator Design
2017 Published in 5th International Symposium on Innovative Technologies in Engineering and Science 29-30 September 2017 (ISITES2017 Baku - Azerbaijan) Investigation of Multiple Evaporator Design * 1 Kemal
More informationEliminating Condensation and Resulting Corrosion. Sulphur Tail Gas and De-Gas Lines
Eliminating Condensation and Resulting Corrosion In Sulphur Tail Gas and De-Gas Lines By David R. Hornbaker, Controls Southeast, Inc. and Graham M. MacPherson, P.Eng., Millenia Resource Consulting Abstract
More informationINTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY
INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY A PATH FOR HORIZING YOUR INNOVATIVE WORK SPECIAL ISSUE FOR NATIONAL LEVEL CONFERENCE "RENEWABLE ENERGY RESOURCES & IT S
More informationA Comparison Between Refrigerants Used In Air Conditioning
A Comparison Between Refrigerants Used In Air Conditioning Derya Özkan, Özden Agra and Özlem Çetin University of Yildiz Technical University, Turkey Corresponding email: tumer@yildiz.edu.tr SUMMARY It
More informationSant Gadge Baba Amravati University. Amravati, Maharashtra, India, Maharashtra 2
2018 IJSRST Volume 4 Issue 8 Print ISSN: 2395-6011 Online ISSN: 2395-602X Themed Section: Science and Technology Heat Transfer Characteristic of Spiral Heat Exchanger: Effect of Reynolds Number on Heat
More informationShortcut Model for Predicting Refrigeration Cycle Performance
17 A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 5, 15 Guest Editors: Petar Sabev Varbanov, Jiří Jaromír Klemeš, Sharifah Rafidah Wan Alwi, Jun Yow Yong, Xia Liu Copyright 15, AIDIC Servizi S.r.l.,
More informationWater Cooled Condenser Using Nano Fluids
Water Cooled Condenser Using Nano Fluids Vishal Vilas Khade Research Scholar, Department of Mechanical Engineering, Ashokrao Mane Group of Institutions, Vathar tarf Vadgaon, Kolhapur, India. Rahul A. Patil
More informationAgitation and Mixing
Agitation and Mixing Agitation: Agitation refers to the induced motion of a material in a specified way, usually in a circulatory pattern inside some sort of container. Purpose is to make homogeneous phase.
More informationThe theory behind heat transfer
Alfa Laval in brief Alfa Laval is a leading global provider of specialized products and engineered solutions. Our equipment, systems and services are dedicated to helping customers to optimize the performance
More informationFeasibility Study of Condensation Heat Exchanger with Helical Tubes for a Passive Auxiliary Feedwater System
Feasibility Study of Condensation Heat Exchanger with Helical Tubes for a Passive Auxiliary Feedwater System Kwanghee Seo 1) and Taewan Kim 2)* 1) KEPCO Engineering & Construction Company. INC., 269 Hyeoksin-ro,
More informationA Thermal Assessment for Vertical Helical Immersion Coil Evaporator in a Water Chiller
American Journal of Energy and Power Engineering 2015; 2(5): 62-73 Published online September 10, 2015 (http://www.aascit.org/journal/ajepe) ISSN: 2375-3897 A Thermal Assessment for Vertical Helical Immersion
More informationExperimental correlation of falling film condensation on enhanced tubes with HFC134a; low-fin and Turbo-C tubes
International Journal of Refrigeration 30 (2007) 805e811 www.elsevier.com/locate/ijrefrig Experimental correlation of falling film condensation on enhanced tubes with HFC134a; low-fin and Turbo-C tubes
More informationHeat Transfer Equipment Overview Core COPYRIGHT. Types of Heat Exchangers and Their Common Applications in Oil and Gas Processing Facilities
Learning Objectives Heat Transfer Equipment Overview Core Types of Heat Exchangers and Their Common Applications in Oil and Gas Processing Facilities By the end of this lesson, you will be able to: By
More information9. ENERGY PERFORMANCE ASSESSMENT OF HVAC SYSTEMS
9. ENERGY PERFORMANCE ASSESSMENT OF HVAC SYSTEMS 9.1 Introduction Air conditioning and refrigeration consume significant amount of energy in buildings and in process industries. The energy consumed in
More informationModule 3: Liquid Fossil Fuel (Petroleum) Lecture 25: Refinery Equipments
1 P age Module 3: Liquid Fossil Fuel (Petroleum) Lecture 25: Refinery Equipments 2 P age Keywords: Pipe still heater, heat exchangers, distillation tower, pumps Refinery equipments Introduction In refinery,
More informationEvaporators. Direct Expansion Flooded Recirculated Over Feed
Evaporators Purpose: Liquid Refrigerant is Boiled from a Low Pressure Liquid to a Low Pressure Gas by Absorbing Heat from the Medium that is being Cooled Types: Direct Expansion Flooded Recirculated Over
More informationDesign of Flat-Plate Dehumidifiers for Humidification Dehumidification Desalination Systems
Design of Flat-Plate Dehumidifiers for Humidification Dehumidification Desalination Systems The MIT Faculty has made this article openly available. Please share how this access benefits you. Your story
More informationAnalysis of Constant Pressure and Constant Area Mixing Ejector Expansion Refrigeration System using R-1270 as Refrigerant
Analysis of Constant Pressure and Constant Area Mixing Ejector Expansion Refrigeration System using R-1270 as Refrigerant Ravi Verma 1, Sharad Chaudhary 2 1, 2 Department of Mechanical Engineering, IET
More informationIntroduction to Heat Exchangers
HEAT EXCHANGERS Introduction to Heat Exchangers What Are Heat Exchangers? Heat exchangers are units designed to transfer heat from a hot flowing stream to a cold flowing stream. Why Use Heat Exchangers?
More informationPaper No. : 04 Paper Title: Unit Operations in Food Processing Module- 14:Evaporation
Paper No. : 04 Paper Title: Unit Operations in Food Processing Module- 14:Evaporation 14.1 Introduction Evaporation is a common unit operation in food processing industries in which partial removal of
More informationChapter 9. Refrigeration and Liquefaction
Chapter 9 Refrigeration and Liquefaction Refrigeration is best known for its use in the air conditioning of buildings and in the treatment, transportation, and preservation of foods and beverages. It also
More informationProcess Simulation and Optimization of Cryogenic Operations Using Multi-Stream Brazed Aluminum Exchangers
Page 1 of 12 Process Simulation and Optimization of Cryogenic Operations Using Multi-Stream Brazed Aluminum Exchangers JOHN C. POLASEK, Bryan Research & Engineering, Inc., Bryan, Texas STEPHEN T. DONNELLY,
More informationExhaust. a) For an arbitrary ambient temperature develop an expression for Q chiller in terms of M amb and M total.
1. State 2 75 o F Exhaust M amb T amb State 3 Room Q chiller State 1 60 o F M total A room at steady state has a supply air stream of cool air entering at 60 o F. The lights, office appliances and people
More informationSHELL AND TUBE HEAT EXCHANGER (STHE) - part b
BEST PRACTICE NO. 47 SHELL AND TUBE HEAT EXCHANGER (STHE) - part b A shell and tube heat exchanger (STHE) consist of several different components and each component needs to be evaluated in the selection
More informationAPPLICATION OF HYDROCARBON REFRIGERANTS IN LOW TEMPERATURE CASCADE SYSTEMS
APPLICATION OF HYDROCARBON REFRIGERANTS IN LOW TEMPERATURE CASCADE SYSTEMS B. M. ADAMSON Refrigeration Engineering Pty Ltd PO Box 1197 Unanderra NSW 2526 Australia Fax +61 2 4262 3001; Email: ben_adamson@refeng.com.au
More informationPaper No. : 04 Paper Title : Unit Operations in Food processing Module 11 : Principles of Refrigeration
Paper No. : 04 Paper Title : Unit Operations in Food processing Module 11 : Principles of Refrigeration 11.1 Introduction Preservation of foods is a vital processing step in food processing. There are
More informationPostprint.
http://www.diva-portal.org Postprint This is the accepted version of a paper presented at 11thIEA Heat Pump Conference 2014, May 12-16 2014, Montréal (Québec) Canada. Citation for the original published
More information