Handling Note SHARP COB ZENIGATA LED SERIES
|
|
- Derek Sims
- 6 years ago
- Views:
Transcription
1 Handling Note SHARP COB ZENIGATA LED SERIES
2 This note applies to Sharp's ZENIGATA series of LEDs. Petit ZENIGATA LED Mini ZENIGATA LED Mega ZENIGATA LED Tiger ZENIGATA LED
3 2 Storage Conditions LED device are kept in trays which are piled on top of one another. These trays are packed in moisture-proof bag. Please use the LEDs as early as possible after opening the moisture-proof bag. Please keep unused LEDs in the bag with some moisture absorbent material(silica gel) or in a desiccator with controlled temperature and humidity. in this case, refer to the storage conditions mentioned in the specification, and store accordingly. The solder pad material of standard ZENIGATA LEDs is made of silver. After opening the aluminum packing bag, if the LEDs are left open for long time, it is possible that the solder pad will oxidize or react with corrosive gases (like Cl2,H2S,NH3, SO2,NOx). This could lead to difficulties during the soldering process and potentially cause damage to the pad. Therefore, please refrain from keeping the LEDs open for long time, and do not store the LEDs in an environment that contains above stated corrosive gases. The following images indicate the change in visual appearance of the pad after oxidation damage:
4 3 Thermal Considerations When using an LED device, use highly thermal conductive material or adhesive sheet and mount on appropriate heat sink. If forward current ( IF ) is applied to LED device alone, without fixing the device to heat sink, temperature of the device will increase beyond the maximum allowed values, and may lead to smoke emission, and other LED device defects. If the device is not mounted properly on the heat sink, heat dissipation does not occur propely, potentially leading to over-heating, which may result in substrate cracking, and failure of the LED. Therefore,careful study should be done when designing a thermal solution before use. 3-1 Heat sink surface The surface of heat sink on which the LED device will be mounted must be flat and free from scratches and debris. If the surface of the heat sink is not flat ( e.g.convex,concave), heat dissipation does not occur properly,potentially increasing the case temperature as well as junction temperature, and ultimately leading to failure of LED device. Any scratches on the surface of heat sink could decrease the thermal conductivity. Therefore please check the surface of heat sink before use. Any deformation or damage to the heat sink surface will increase thermal resistance and decrease heat dissipation, potentially leading to over-heating and ultimately failure of the LED. If the surface of the heat sink is not flat(e.g.convex) it may induce cracking of the ceramic substrate which will result in failure of the device.
5 3-2 Mounting on Heat sink When mounting LED device on heat sink, use highly thermal conductive adhesive material or adhesive sheet. In case of holder also,please mount in the similar way. In either case, use effective heat dissipation material in between heat sink and ceramic substrate as shown in below figure, and also take careful note of the reliability of heat dissipation and adhesion. Make sure the device will not detach from the heat sink even when used for long time, and the case temperature does not exceed maximum rating value. Increase in the temperature of LED device beyond the maximum allowed values may lead to device deterioration, lead wire detachments, smoke emission, and other LED device defects. LED device Adhesive Material Heat Sink Closely contact
6 3-3 Thermal adhesive selection If opting to use a thermal adhesive to attach the LED to heat sink, please select a product with high thermal conductivity. Reliability tests should be performed before entering mass production,especially for high wattage LEDs such as the Mega-ZENIGATA series. Example products with suitable thermal characteristics:(data provided by adhesive suppliers) ST0903 (Silanex Technology) 30 W/m K TIA600R ( Performance Materials) 6 W/m K To ensure good heat dissipation, check that the mating surface of the LED device and heat sink are clean without any foreign materials on the surface, and that the thickness of the adhesive is controlled to be less than 100um. The adhesive should be spread uniformly across the entire back surface of the LED ceramic substrate. It is recommended that adhesive material is pushed out from every side of the substrate by pressing ZENIGATA LED on the heat sink during the mounting process. 1)Adhesive uniformity If adhesive is not spread uniformly across the back side of the ceramic substrate, LED may be damaged by local heat build-up, even if Tc is controlled with in specification. In such cases, local variations in thermal expansion may cause the ceramic substrate to crack. 2)Thermal grease selection If opting to use a thermal grease to make contact between LED and heat sink, please select a product with high thermal conductivity. Considerations on thickness and uniformity are the same as for thermal adhesives. Please check lifetime performance of heat dissipation as this may be affected by solidification or other forms of degradation after long periods of use.
7 3) Thermal sheet selection Please use highly adhesive thermal sheet to make contact between LED device and heat sink. For better adhesive performance, thermal sheet which is soft is recommended to use. Please use the thermal sheet which has thermal conductivity more than 3 W/m K Example: FSL-B (DENKI KAGAKU KOGYO) (data provided by the supplier) 3W/m K If the thermal sheet which doesnʼt have good adhesive property is used, gap may arise between LED device and thermal interface material, which may affect the heat dissipation of the device. If the LED device detaches from the thermal sheet, LED may get damage due to overheat. Therefore fix the LED device using holder. Please select a product which has good adhesive performance on both sides, and thickness<0.3mm. Moreover, the long-time reliability of the thermal sheet on the lighting fixtures should also be studied carefully before use. 4) Reliability of adhesive, grease, thermal sheets The performance of the adhesive, grease, thermal sheets may change due to the effect of heat and light when used for long time. The long-time reliability of thermal interface materials should be studied very carefully before mass production. ZENIGATA LEDs do exhibit some light leakage through the ceramic substrate. Please carefully study the effect of heat and light on these materials. Please take note of the effect of materials such as low molecular weight silicone compounds that may emit from the grease or other materials used between heat sink and the LED device. 5) Effect of heat sink and other heat dissipation materials on LED deviceʼs light output The light reflectivity efficiency of heat sink and other thermal interface materials may affect the light-output of LED device. Therefore it is very important to verify the following factors while designing thermal solutions: 1. Whether the initial reflectivity efficiency values of the above mentioned materials are stable or not. 2. Whether any color change that occurs due to long term use has an effect on light output.
8 Handling Note 3-4 COB Holder usage When using a holder to fix the LED device with heat sink, please use a thermal interface material (E.g.grease or thermal sheet) on the back side of the device. LEDs with solder-less connection pad material are not compatible with soldering processes. In case a solder-less electrical connector will be used, a different pad material is available and should be considered depending on the application. We recommend that electrical contact between LED and holder is made using spring connectors to regulate the pressure applied to the LED. If excessive pressure is applied it may result in damage to the LED contact pad or even cracking of the ceramic substrate. The performance of the holder may change due to the effect of heat and light when used for long time. The long-time reliability of holders should be studied very carefully before use. 3-5 Positioning of the LED device When searching for the fixing-point for LED device or for the holder fixing design,please avoid using the corners for position fixing, as there may be salient areas on the corners (edges) of LED device. Any excessive or uneven stress on the ceramic substrate could break the substrate. Please design such that, proper/uniform stress is applied on the substrate, when fixing the LED device using a holder. In case of using an impact driver to fasten screw to fix the holder and the LED device, make sure that the vibration created by the driver does not have any effect on the quality issues of the LED device. When fixing the LED device with a holder, please take note of any excessive or uneven stress is applied when pressing the substrate with holder. Due to this reason,gap may arise between LED device and thermal interface material,which may affect the heat dissipation of the device.
9 Handling Note Contents in this technical document be changed without any notice due to the product modification. ④ LED Handling When mounting ZENIGATA LEDs, please handle by side part of substrate or the specified area shown below. Do not touch the colored resin area of the LED or the white dam ring that surrounds it, as there are wire connections underneath. Additional components(holder, lens) should be designed to avoid this area. Holding section TIGER-ZENI, MEGA-ZENIGATA, MINI-ZENIGATA, PETIT-ZENIGATA > Use anti static gloves or tweezers that are not sharp, and handle at the specified handling area. > Do not handle at the solder pads > Do not handle on the resin area (including white resin) > Do not handle with bare hands 8
10 Handling Note White Resin area Coloured resin area (light emitting area) There are wire connections beneath white resin area and light emitting area. Any external pressure on this area could bend or cut-off the wires, which may result in device failure. If any external pressure is applied on the resin area, damage may occur to the wires underneath the resin as shown in below figure. (X-ray inspection) Wire deformation Wire cut Wire cut Wire deformation It is recommended to avoid using pointed tools for handling ZENIGATA LEDs, as they may damage the resin area on the LED device.
11 Handling Note The temperature of LED devices should be maintained as per the Tc (case temperature) measured at the measuring point mentioned in the specification, and always use it inside the range of de-rating curve. While measuring Tc, please take care of the following things: The LED device mounting surface should be flat/plain surface. The substrate surface temperature should be uniform. Refer to section6 for regulations related to soldering temperature and reliabilities. The de-rating curve in the specification does not guarantee solder connection. In case of solder connection, use the LED device that is designed with soldered electrical connections. An example for solder connection: Soldering Duration: 3 seconds (Keep the device on the material that has less conductivity while soldering) Soldering iron: HAKKO FX-591(Main Body), FM-2028(solder iron), T12-B2(solder iron tip) Soldering iron tip temperature: 380 degrees Soldering Material: Wire solder Senju Metal Industry M mm Temperature controlled soldering iron is recommended to use. However, solder may not melt properly or contaminate electrodes, depending on the material properties of soldering iron, solder, and also heat dissipation performance of the material on which soldering is done. Therefore, please check the conditions carefully before soldering. If soldering is done after the LED is mounted on heat sink, it may be difficult to reach a high enough temperature to melt the solder. In that case, increase the temperature of the soldering tip to ensure a high quality soldered connection. If pre-soldering is possible before mounting on heat sink, it is recommended to do pre-soldering on electrodes of the LED device. The ceramic substrate has a very high thermal conductivity. Due to this reason, when soldering, do not keep the LED device on a high thermal conductive object, as this may prevent the solder pad reaching a sufficiently high temperature. We recommend using hotplate with preset temperature. (preset condition:100 deg. to 150 deg: under 60 seconds) A soldering material with good reliability at elevated temperatures is essential because the LED will go through many temperature cycles during its lifetime. Lower quality materials may experience cracking or creep. The soldering iron should not touch the resin(circular) area of the LED. To avoid damage to this area, you are advised to do the soldering process such that the soldering tool approaches the pad from the outside of the LED, as depicted in the diagram below.
12 Solder iron Solder iron Solder iron does not touch the resin. Solder iron may touch the resin. LEDs with Solder connection pad material are not compatible for solder-less connection. Others: Please do not attempt to re-solder a detached wire as this may result in a connection with reduced strength. Soldering should be performed on a stable stand. Avoid soldering ZENIGATA LED devices on vibrating or moving objects. Please ensure that the entire pad is covered in solder. Please prevent flux and other soldering particles from touching the resin. Flow/reflow soldering techniques are not applicable for ZENIGATA LED devices. Please refrain from using soldering paste. Please arrange wire to not cause mechanical stress to the solder pad. Secure the solder wettability on whole solder pad and leads. In case of using at high temperatures, use the soldering material that can withstand creep failures. LED devices that are designed for soldered connections, should not be connected with other solder-less electrical connectors. Solder-less connections are prone to oxidation and sulphurization, which could cause defects in electrical connectivity. In case a solder-less electrical connector will be used, a different pad material is available and should be considered depending on the application. LEDs with solder-less connection pad material are not compatible with soldering processes.
13 7 Operating Environment This product is not designed for use under any of following conditions: A high moisture environment. In briny air or corrosive gas (Cl, H2S, NH3, SO2, NOx, etc.) Under direct sunlight (due to photo voltaic effect). Outdoor exposure. Dust. Water, oil, medical fluid or organic solvent. Careful attention should be made to the nature of compounds out gassed by materials and components within an LED lighting fixture - specifically their compatibility with the LED device. If such compounds are prone to photo-degradation the degradation the degradation products must also be considered. The closed nature of many lighting fixtures means that such compounds can become trapped, potentially resulting in high concentrations close to the LED. Some compounds known to be detrimental to the LED include silicones, volatile organic solvents(vocs), strong acids and alcohols. If a customer intends to use a ZENIGATA LED under any of these conditions they will need to confirm performance and reliability for themselves. The chemicals listed in below table have potential risks to react with chip, silicone resin or other materials in LED device and may cause quality problems for LED device. Therefore, the materials which contain or generate these chemicals should not be used in the vicinity of LED device. If they are necessary to use around LED device, please evaluate and check the effect of these chemicals on LED device performance and reliability
14 Handling Note
15 Handling Note <Effect of LED light on surrounding materials> The light from LED could change the color or shape of surrounding materials. Please check the reliability of these materials with LED device before use. <Under sunlight> When an LED is illuminated under sunlight the photoelectric effect can induce a reverse voltage and damage the device. Please prevent direct and indirect illumination of ZENIGATA LEDs by sunlight The photo-voltaic effect is dependent on the properties of the light illuminating a chip and the characteristics of the chip itself. ZENIGATA LEDs are connected in series, meaning the LED chip with the lowest electromotive force(e.m.f) will be affected by the reverse voltage of all LED chips in the series. Current [na] I-V Behavior Light intensity Voltage[V]
16 8 Driver Design LED chips are connected in both series and parallel in ZENIGATA LED. With increase in temperature, the voltage of LEDs will decline. Therefore, do not use constant voltage power supplies as current may increase beyond safe limits. It is recommended to use the constant current power supply (Avoid using Constant Voltage Power Supply). When multiple ZENIGATA LEDs are used, connect the LED devices in series only. If the ZENIGATA LEDs are connected in parallel, there is a danger that high currents may pass through those LEDs with the lowest voltages. Therefore avoid connecting ZENIGATA LEDs in parallel. Power Source Do not connect the ZENIGATA LEDs in parallel Please use a driver with built-in surge protection. Do not apply reverse polarity to the LED. Furthermore, when the LED is not in operation avoid applying any voltage(forward or reverse voltage). Design the driver to avoid spikes in current as inrush currents may cause gold contact wires to melt. If the LED device is switched(on/off) excessively, the resin surface on the device will expand and shrink several times due to the temperature difference. This could damage the wires in between LED dies, and may lead to device failure. Therefore, before using the LED device, please do the tests considering usage environment.
17 9 Other Considerations To protect from electrostatic damage, please use an anti static wrist band when handling. Do not use tools and processes which create a large amount of vibration as this may damage the LED. The light and heat released from LED device may change the properties of materials of LED lighting fixtures(lens, reflectors, holders) that are used around the LED. Therefore, the material properties of fixtures should be considered carefully before designing. If the LED lighting fixtures are designed in such a way, that the light from the LED device is concentrated narrowly, or when high power LED devices like MEGA ZENIGATA are used, it is important to check the light energy from the LEDs do not cause any abnormal heat generation or smoke emission due to light observation or color degradation of the fixtures. Avoid cleaning, since silicone resin may be eroded by cleaning. 10 Safety Precautions Looking directly at LEDs for a long time may result in hurting your eyes. In the event of excess current(over ratings) being supplied to the device, hazardous Phenomena including abnormal heat generation, smoke emission, or fire can be caused. Take appropriate measures to avoid excess current and voltage. Please confirm the safety standards or regulations of application devices. Please be careful with substrate edges, which may injure your hands.
18
Metal, ceramic, plastic package products
Precautions Metal, ceramic, plastic package products This document describes general precautions for using Hamamatsu opto-semiconductors of metal, ceramic, and plastic packages (hereafter called the product
More informationSpecific Lighting Product Data Sheet M08 CoB Product Series Data Sheet Spec No.: DS Effective Date: 12/15/2016 LITE-ON DCC RELEASE
Specific Lighting Product Data Sheet Data Sheet Spec No.: DS23-2016-0114 Effective Date: 12/15/2016 Revision: - LITE-ON DCC RELEASE BNS-OD-FC001/A4 LITE-ON Technology Corp. / Optoelectronics No.90,Chien
More informationHigh Power COB LED. Features. Applications. ① Product line code: COB10W-C & COB10W-W. ② Product code base plate. ③ Chip code. ④ Emitting light colours
High Power COB LED ① Product line code: COB10W-C & COB10W-W ② Product code base plate ③ Chip code ④ Emitting light colours ⑤ ecommend the minimum Power ⑥ The number of parallel Circuit ⑦ The number of
More informationPreliminary specification
Deep UV LED - 340nm UV CA3535 series (CUD4GF1A) CUD4GF1A RoHS Product Brief Description CUD4GF1A is a deep ultraviolet light emitting diode with peak emission wavelengths from 340nm to 345nm. It incorporates
More informationPRODUCT SPECIFICATION
PRODUCT SPECIFICATION Features: High-Power LED Type Size (mm):φ6*5.1 Emitting Color:ULTRAVIOLET SMT package RoHS Compliant Decorative lighting Architectural lighting Chemical Testing Material Identification
More informationApplication note. LCD Module. Precautions for LCM handling. LCM handling V 1.1
LCD Module Precautions for LCM handling Application note LCM handling V 1.1 admatec GmbH Wendenstrasse 29, 20097 Hamburg, Germany Tel.: +49-40-238533-0, Fax: +49-40-238533-11 Internet: www.admatec.de,
More informationAPPLICATION NOTES for LED DISPLAYs
THROUGH HOLE DISPLAY MOUNTING METHOD LEAD FORMING Do not bend the component leads by hand without proper tools. The leads should be bent by clinching the upper part of the lead firmly such that the bending
More informationApplication Notes For LED Displays
Through Hole Display Mounting Method Lead Forming Do not bend the component leads by hand without proper tools. The leads should be bent by clinching the upper part of the lead firmly such that the bending
More informationPRODUCT SPECIFICATION
PRODUCT SPECIFICATION High-Power LED Type Size (mm):φ6*5.1 Emitting Color:Warm White SMT package RoHS Compliant Features: Decorative lighting Architectural lighting Interior automotive Illuminations Applications:
More informationPRODUCT SPECIFICATION
PRODUCT SPECIFICATION 1W WHITE LED MODULE Features: High-Power LED Type Size (mm):φ6*7.1 Emitting Color: Warm White SMT package RoHS Compliant Decorative lighting Architectural lighting Interior automotive
More informationTOCOS. Guidelines & Precautions. For Using Trimmer Potentiometers. Guidelines for Circuit Design. Guidelines for Production Processes
TOCOS Trimmer Potentiometers are designed and manufactured with emphasis on dependability and costeffectiveness. For reliable performance and general safety, follow these guidelines and precautions for
More informationSpecification MBT801-S
Specification MBT801-S Drawn SSC Approval 고객명 Approval www. MBT801-S 1. Features 2. Absolute Maximum Ratings 3. Electro Characteristics 4. Optical characteristics 5. Outline Dimension 6. Packing 7. Soldering
More informationRoHS. Specification SAWW9H0A. 서식번호 : SSC-QP (Rev.00)
Specification RoHS SAWW9H0A 1 Description SAWW9H0A SAWW9H0A Features Super high flux output and high luminance Designed for high current operation SMT solderable Lead free product RoHS compliant The Acrich
More informationML562G84 APPLICATION. Display system. Symbol Parameter Conditions Ratings Unit. Pulse (Duty 40%)
TYPE NAME DESCRIPTION Mitsubishi is a high-power, highly efficient semiconductor laser diode which provides emission wavelength of 638 nm and standard light output of 2.5W (pulse). This LD has broad-stripe
More informationMINI PARALLEL REMOVER. Iron holder with a sleep mode. Instruction Manual CAUTION
MINI PARALLEL REMOVER Iron holder with a sleep mode Instruction Manual l Thank you for purchasing the FM-2023 mini parallel remover. Please read this manual before operating the FM-2023. Keep this manual
More informationTSLC 6 UV LED 24v Strips
TSLC 6 UV LED 24v Strips ILS-XC06-####-SD111. Product Overview At the heart of each UV 6 product are 6 compact, high quality and reliable TSLC C3535 1-chip UV LED, with a primary 125 degree lens, featuring
More informationML60171C FEATURES. φ5.6mm TO-CAN PKG (with monitor PD) APPLICATION Motion sensor Printing. Reverse voltage (PD)
TYPE NAME DESCRIPTION Mitsubishi ML6xx71 is a highpower, highefficient semiconductor laser diode which provides emission wavelength of 827 nm and standard light output of 260mW. This LD has narrowstripe
More informationML520G55 FEATURES. Package: φ5.6mm TO-CAN PKG APPLICATION. Reverse voltage
TYPE NAME DESCRIPTION Mitsubishi ML5xx55 is a high-power, high-efficient semiconductor laser diode which provides emission wavelength of 638 nm and standard light output of 150mW. This LD has narrow-stripe
More informationWood pellet and biomass system ceramic igniter
Wood pellet and biomass system ceramic igniter Specification Data Product name: Ceramic Igniter PSx-6-240-B Drawing number: IBA-HH008A Revised on: 2015.12.20 1. Application This engineering specification
More informationML501P73 TYPE NAME. FEATURES High Output Power: 1.0W (Pulse) 0.5W (CW) High Efficiency: 1.0mW/mA (typ.) Visible Light: 638nm (typ.) 5.
LASER DIODES TYPE NAME ML501P73 DESCRIPTION Mitsubishi ML501P73 is a high-power, highly efficient semiconductor laser diode which provides emission wavelength of 638 nm and standard light output of 1.0W
More informationToshiba Memory Corporation Semiconductor Handling Precautions and Requests
Toshiba Memory Corporation Semiconductor Handling Precautions and Requests Ver.2 July 2018 Table of contents Handling Precautions and Requests Chapter 1 Usage Notes for Semiconductor Products... 4 Chapter
More informationCree XLamp CM Family LEDs
soldering & handling CLD-AP240 Rev 1 Cree XLamp CM Family LEDs Introduction Table of Contents www.cree.com/xlamp This application note applies to XLamp CM family LEDs, which have order codes in the following
More informationPRODUCT SPECIFICATION
FYLP-5W-UBL- PRODUCT SPECIFICTION High-Power LED Type Size (mm):φ6*8.0 Emitting Color:Blue SMT package RoHS Compliant Features: Decorative lighting rchitectural lighting Interior automotive Illuminations
More informationEN , EN , DALI 102/207, SELV Output, KS C 7655 Safety Certification Approved RoHS Compliant. Dim. Method
PIFE-W037D Flat 35W LED Driver 24V - 34V / 1.04A / 35W Features Dimmable Method: DALI Dimming Constant Current Control Active Power Factor Correction Protection : OVP, SCP and OTP Mechanical Outline (Metal
More informationProduct Brief. specification. UV Module Solution. Description. Features and Benefits. Key Applications CMW-PS-C01. Table 1.
UV Module Solution specification Product Brief Description is disinfection Module with UV LED mounted on the Metal PCB. It can be easily connected electrically by putting in the connector. UV module is
More information2. Contact form 6: 1c (SPDT) Load voltage (peak value) quantity Fully Sealed 1c (SPDT) 5 VDC 5 VDC 60 V 400 ma 130 ma G3VM-66M 50 pcs/tube
MOS FET Relay in module package with SPDT (1C) This model of operated by voltage (Rated input voltage is 5 VDC.) Contribute to reduce the mounting space on the print circuit board by small package Contact
More informationSPECIFICATIONS. US0603YG LED Chip 0603 Yellow Green SWISSDIS. Swissdis AG Grasweg 7 CH-4911 Schwarzhäusern
SWISSDIS Swissdis AG Grasweg 7 CH-4911 Schwarzhäusern Tel.: +41 62 919 44 00 Fax: +41 62 919 44 01 info@swissdis.ch www.swissdis.ch SPECIFICATIONS US0603YG LED Chip 0603 Yellow Green Version December 2015
More informationTechnical Data Sheet. Pb Free. Specification NB104 SSC. Customer. Rev. 03 July 서식번호 : SSC- QP (Rev.0.
Specification NB104 Pb Free Drawn SSC Approval Customer Approval [ Contents ] 1. Description 2. Absolute maximum ratings 3. Electro-Optical characteristics 4. Characteristic diagrams 5. Reliability result
More informationInstruction Manual. gray Mounted Detectors. for. greenteg AG Technoparkstrasse Zürich, Switzerland T: F:
gray Instruction Manual for gray Mounted Detectors F: +41 44 633 13 68 2 / 12 gray Mounted Detectors: Instruction Manual CONTENT 1. SHORT USER GUIDE... 4 2. THERMAL INTEGRATION OF THE DETECTOR... 5 2.1.
More informationHandling or using the product improperly and in disregard of the instructions with this mark might result in serious bodily injury or death.
Please Read: Safety Precautions DC AC In order to ensure that this product is used safely, be sure that you read and understand the following precautions fully and use the product only as directed. Be
More informationThe Basics of Package/Device Cooling
The Basics of Package/Device Cooling Various cooling methods are available for keeping electronic devices within their operating temperature specifications. Cooling Consumer Products In the case of consumer
More informationELIMINOSTAT DC-ESR-CL-S2
Static Clean Instruction Manual DC Voltage Application Method Static Eliminators Static Eliminator with Integral Power Supply ELIMINOSTAT DC-ESR-CL-S2 Thank you for purchasing the Static Eliminator ELMINOATAT
More informationA214B/SUG/S400-X6 LAMP. Features. Description. Applications. Revision 1. Expired Period: Forever. LifecyclePhase: Low power consumption
Features Low power consumption High efficiency and low cost Good control and free combinations on the colors of LED lamps Good lock and easy to assembly. Stackable and easy to assembly Stackable vertically
More informationOPERATING INSTRUCTIONS WPSI12. Portable Soldering Station & TCP12. Soldering Tool. Weller Tech Sheet Product Code: Issue A 24/05/05
OPERATING INSTRUCTIONS WPSI12 Portable Soldering Station & TCP12 Soldering Tool WELLER WPSI12 PORTABLE SOLDERING STATION AND TCP12 SOLDERING TOOL DESCRIPTION The Weller WPSI12 Portable soldering station
More informationFollowing this guideline enables proper treatment of the relays during the critical phase in the relay life.
Electromechanical relays are one of the most robust and most reliable electronic components. In order to achieve and guarantee the excellent performance of AXICOM relays, some precautions must be taken
More informationUsed as indicators of indicating the Degree, Functions, Positions etc, in electronic instruments
Features Low power consumption High efficiency and low cost Good control and free combinations on the colors of LED lamps Good lock and easy to assembly. Stackable and easy to assembly Stackable vertically
More informationan ISO9001 company TECHNICAL INFORMATION FOR TGS813 Technical Information for Combustible Gas Sensors
TECHNICAL INFORMATION FOR TGS83 Technical Information for Combustible Gas Sensors an ISO900 company Figaro TGS 8-series sensors are a type of sintered bulk metal oxide semiconductor which offer low cost,
More informationSMD 2121 Black Frame MC-S2121BHA
SMD 2121 Black Frame MC-S2121BHA 1. SPECIFICATIONS 1.1 Absolute Maximum Ratings (Ta=25 C) Item Symbol Absolute Maximum Rating Red Green Blue Unit Forward Current I F 30 30 30 ma Pulse Forward Current I
More informationInt2930. Soldering Station. Instruction Manual
Int2930 Soldering Station Instruction Manual Thank you for purchasing the Aoyue Int2930 Soldering Station. Please read the manual before using the unit. Keep manual in accessible place for future reference.
More information474A+ TIP CARE AND USE INSTRUCTION MANUAL DESOLDERING STATION
TIP CARE AND USE. Tip Temperature High soldering temperatures can degrade the tip. Use the lowest possible soldering temperature. The excellent thermal recovery characteristics ensure efficient and effective
More informationInt 937. Soldering Station. Instruction Manual. Correct Disposal of this product
Int 937 Soldering Station Instruction Manual Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible
More informationSERVICING INFORMATION
SERVICING INFORMATION OPTIKINETICS SOLAR 250 (Early Type) M.Ginda 06/03/08 1 Servicing the Solar 250 effects projector. This is a short guide on how to service the main component parts of the projector.
More informationHere Comes the Sun!!!
Technical Article Here Comes the Sun!!! Construction of solar photovoltaic (PV) power supply systems!! What calls the standard DIN VDE 0100-712 for the construction of solar photovoltaic (PV) power supply
More informationPiezo-electric Devices Precaution Usage
Version: January 16, 2017 Piezo-electric Devices Precaution Usage Token Electronics Industry Co., Ltd. Web: www.token.com.tw Email: rfq@token.com.tw Taiwan: No.137, Sec. 1, Zhongxing Rd., Wugu District,
More informationAUBREY with MAJOLICA PORTO Operation / Installation manual
AUBREY with MAJOLICA PORTO Operation / Installation manual Contents Preparation before Installation (Specification Drawings) Usage condition Parts List / Accessory Parts Installation Procedure Safety Precautions
More informationG155PU001S. Pigtailed 14-PIN DIL Laser Diode with TEC. FLMS Min. Typ. Max.
G155PU001S TECHNICAL DATA Pigtailed 14-PIN DIL Laser Diode with TEC Features 1 mw 1550 nm MQW Laser Diode Module with cooler 14pin DIL package with single mode fiber output Applications Optical Communication
More informationFagronLab NP-1 UV. Negative pressure workbench. User Manual
Negative pressure workbench User Manual Table of contents 1. Introduction... 3 2. Service... 3 3. Warranty... 3 4. Application range... 4 5. Main technical parameters... 4 6. Performance index... 5 Vibration
More informationContents. Introduction... A Note About Heatsinks... Precautions...
Contents Introduction... A Note About Heatsinks... Precautions... Application Instructions... Heatsink Preparation... CPU Preparation... Tinting the Heatsink and Metal cap... Applying Thermal Compound...
More informationELLA ID. High CRI, High lm/w OptoDrive LED-module
ELLA ID ELLA ID High CRI, High lm/w OptoDrive LED-module Page 2 of 24 Pages for reference: Pages for reference:... 2 Introduction... 3 Short form Characteristics... 4 Wiring diagram:... 6 Accessories to
More informationAOYUE 968A+ INT. Deluxe Repairing System INSTRUCTION MANUAL
AOYUE INT 968A+ Deluxe Repairing System INSTRUCTION MANUAL Thank you for purchasing Aoyue INT 968A+ Repairing System. It is important to read the manual before using the equipment. Please keep manual in
More informationInstruction Manual. gray Housed Detectors. for. greenteg AG Technoparkstrasse Zürich, Switzerland T: F:
gray Instruction Manual for gray Housed Detectors F: +41 44 633 13 68 info@ 2 / 10 gray Housed Detectors: Instruction Manual CONTENT 1. SHORT USER GUIDE... 4 2. THERMAL INTEGRATION OF THE DETECTOR... 5
More informationSoldering Station INSTRUCTION MANUAL
2 9 0 0 Soldering Station INSTRUCTION MANUAL Thank you for purchasing model 2900 Soldering station. Please read manual before using the unit. Keep manual in an accessible place for future reference. Manufacturer:
More informationData Sheet Sensor: IRA-S210ST01 Lens: IML-0685 / IML Sensor : IRA-S210ST01 Lens : IML-0685/0688. Pyro Electric Infrared Sensor Fresnel Lens
Sensor : IRA-S210ST01 Lens : IML-0685/0688 Pyro Electric Infrared Sensor Fresnel Lens Features Excellent S/N Low voltage operation available Applications Intrusion Detectors Lighting Automation Please
More informationComposite Sinks Installation, Use and Maintenance
Composite Sinks Installation, Use and Maintenance Customer Care Department The Group Ltd. Harby Road Langar Nottinghamshire NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu
More informationOPERATIONS MANUAL. Hotplate Stirrer/Hotplate/Magnetic Stirrer Model HTS-1003/HTP-1002/MGS Certified
OPERATIONS MANUAL Hotplate Stirrer/Hotplate/Magnetic Stirrer Model HTS-1003/HTP-1002/MGS-1001 Certified Contents 1. Safety 3 2. Introduction 7 3. Package Contents 7 4. Specifications 7 5. Features 8 6.
More informationE Specifications. Ver.1.2. Page: EKMC Product Name. Model Number. 3.Dimensions. Approved by. Checked by.
(0.177) (0.079) (0.181) (0.311) (0.677) E645 Specifications 1. VZ series Standard motion / Slight motion detection type (170μA / Digital output) 1 2.Model Number Lens Color White Black Pearl White 3.Dimensions
More informationHeated tools. Semiconductor equipment
Heated tools Semiconductor equipment Ceramic heating elements made of silicon nitride and aluminum nitride can be manufactured as tools in various shapes. The heating function can be integrated in complex
More informationAOYUE INT. Advanced Repairing System NT 701A++ INSTRUCTION MANUAL. Correct Disposal of this product
This appliance can be used by children aged form 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision
More informationCATALYTIC EMITTER - An old idea in new clothes
Page: 1 CATALYTIC EMITTER - An old idea in new clothes 1. Physical Basis There are three kinds to transfer heat: conduction, convection and radiation. In case of conduction the heat is transferred from
More informationIAQ_100 C Package
15x15 Indoor Air Quality Sensor 100 ppm C Package 110-802 DESCRIPTION SPEC Sensors IAQ_100 is a Screen Printed ElectroChemical sensor component specifically designed for the broad detection of gases associated
More informationInstruction Manual. for. Intelligent Temperature Controlled Soldering Station LF-2000 (U)
Instruction Manual for Intelligent Temperature Controlled Soldering Station LF-2000 (U) For Lead-free soldering application and rework on professional SMD electronics. 1 INTRODUCTION Thank you for purchasing
More informationQuartzone. Infrared Quartz Tube & Metal Sheathed Electric Heaters. Owner s Manual. File E COMFORT HEATERS for INDOOR* and OUTDOOR** USE
Quartzone Infrared Quartz Tube & Metal Sheathed Electric Heaters Owner s Manual File E97759 COMFORT S for INDOOR* and OUTDOOR** USE *Excluding Residences ** With Quartz Elements and when mounted Underneath
More informationThe True Value of Connector Inspection: New Challenges and Best Practices
The True Value of Connector Inspection: New Challenges and Best Practices Vincent Racine Product Line Manager August 2011 1 Table of contents 1 Best Practices 2 Connector Inspection Tools 3 Connector Inspection
More informationG Specifications. Ver.1.1. Page: EKMC K. 1.Product Name. Model Number. 3.Dimensions. Approved by. Checked by. ,2018 Mar.
1. 2.Model Number VZ series Long distance detection type (170μA / Digital output / High Sensitivity) Lens Color White Black Pearl White Model Number EKMC4603111K EKMC4603112K EKMC4603113K Marking 1 3.Dimensions
More information(PT-A1-AC ) Surface Mount Ambient Visible Light Sensor. Electronics Tech. Direct Electronics Industry Co., Ltd. Version: July 31, 2017
Version: July 31, 2017 Electronics Tech. (PT-A1-AC-3528-850) Surface Mount Ambient Visible Light Sensor Web: www.direct-token.com Email: rfq@direct-token.com Direct Electronics Industry Co., Ltd. China:
More informationSensor : IRA-S210ST01 Lens : IML-0685/0688 Pyro Electric Infrared Sensor Fresnel Lens Features Applications Excellent S/N Intrusion Detectors
Sensor : IRA-S210ST01 Lens : IML-0685/0688 Pyro Electric Infrared Sensor Fresnel Lens Features Excellent S/N Low voltage operation available Applications Intrusion Detectors Lighting Automation Please
More informationRead this Safety Guide first.
LCD Projector User's Manual - Safety Guide Thank you for purchasing this projector. About The Symbols Read this Safety Guide first. Before using, read the user manuals for this projector to ensure correct
More informationSMT450. High Performance TOP LED
High Performance TOP LED Outer Dimension (Unit:mm) - Chip Material: InGaN - Number of Chips: 1pcs - Chip Dimension: 350um x 350um - Peak Wavelength: 450nm typ. - Lead Frame Die: Siliver
More informationANLAGENBAU HEAT EXCHANGER w w w. a nla g enba u-b oehm er. d e Version 05/2015
ANLAGENBAU HEAT EXCHANGER Table of Contents 1.0 General Information 1.2 User Instructions 1.3 Proper Use 1.4 General Safety Rules 2.0 Design and Function 3.0 Installation 3.1 Setting up the Plate Heat
More informationAGC Sputter Coating Glass Processing Guidelines
TECHNICAL SERVICES DOCUMENT TSD-217 AGC Sputter Coating Glass Processing Guidelines Introduction Comfort Select and Energy Select are Low-Emissivity glasses manufactured by AGC Glass Company North America.
More informationG Specifications. Ver.1.1. Page: EKMC K. 1.Product Name. Model Number. 3.Dimensions. Approved by. Checked by. ,2018 Mar.
1 1. VZ series Slight motion detection type (170μA / Analog output) 2.Model Number Lens Color White Black Pearl White Model Number EKMC2691111K EKMC2691112K EKMC2691113K Marking 3.Dimensions Top VIEW G745
More information474 DESOLDERING STATION
474 DESOLDERING STATION INSTRUCTION MANUAL Thank you for purchasing 474 Desoldering Station. Please read the manual before using the unit. Keep manual in accessible place for future reference. Manufacturer:
More informationChecking the components Safety information Operating the product Other information
1 Feature of your product Always provide powerful elimination performance 2/4 Samsung SPi device has been applied on the left/right side of the product for quick and powerful elimination performace. Luxurious
More informationHG-2000E HEAT GUN WATTS
HG-2000E HEAT GUN 2.000 WATTS EN - INSTRUCTIONS Carefully read the instructions for use before you start using the machine. drivenbycare www.orfit.com 1 2 6 8 7 2 8 450 C 300 C 6 A E FE 550 C PVC (hard)
More informationWood pellet and biomass system ceramic igniter
Wood pellet and biomass system ceramic igniter Specification Data Product name: Ceramic Igniter PSx-6-120-W Drawing number: IBA-HH024A Revised on: 2017.11.08 1. Application This engineering specification
More informationDehumidifier. Instruction Manual. Model DH-320/A
Dehumidifier Instruction Manual Model DH-320/A CONTENTS Safety Warnings 2 Operation consideration 5 Construction & controls 6 Function selection 8 Preparation for use 10 Operation 12 Maintenance 14 Continuous
More informationHOT BAR REFLOW SOLDERING FUNDAMENTALS by Amada Miyachi Europe A high quality Selective Soldering Technology
HOT BAR REFLOW SOLDERING FUNDAMENTALS by Amada Miyachi Europe A high quality Selective Soldering Technology Content 1. Hot Bar Reflow Soldering Introduction 2. Application Range 3. Process Descriptions
More informationAOYUE AOYUE. Soldering Station. Soldering Station. Instruction Manual. Instruction Manual
AOYUE 69 Soldering Station Instruction Manual AOYUE INTERNATIONAL LIMITED Jishui Industrial Zone, Nantou, Zhongshan City, Guangdong Province, P.R.China http://www.aoyue.com Thank you for purchasing the
More informationRegular Corona Surface Treater Maintenance Cuts Scrap, Reduces Downtime, Boosts Productivity By Mark Spaulding with Tom Gilbertson and Matt Rajala
Regular Corona Surface Treater Maintenance Cuts Scrap, Reduces Downtime, Boosts Productivity By Mark Spaulding with Tom Gilbertson and Matt Rajala Live Long and Prosper isn t just a saying from Star Trek.
More informationDisposal Manual. m{zd{ 6. Capacitor( -ELOOP ) October 2012 Mazda Motor Corporation
Capacitor( -ELOOP ) Disposal Manual m{zd{ 6 Vehicle type in VIN : JM* GJ ****** 100001~ JM* GL ****** 100001~ RUM GJ ****** 100001~ October 2012 Mazda Motor Corporation 1 Capacitor disposal manual_gj_eng161128.xlsx
More informationPD100MF0MPx. Surface Mount Type, Opaque Resin Photodiode. PD100MF0MPx. Agency Approvals/Compliance. Features. Model Line-up.
PD100MF0MPx Surface Mount Type, Opaque Resin Photodiode Features 1. Compact and thin SMD package 2. Top view and side view mountable 3. Plastic mold with visible light cut-off black resin lens 4. Peak
More informationSP2000. Solder Pot. Environment Friendly. Instruction Manual
SP2000 Environment Friendly Solder Pot Instruction Manual Thank you for purchasing the Aoyue SP2000 Solder Pot. Please read the manual before using the unit. Keep manual in accessible place for future
More informationInstruction Manual TABLE OF CONTENTS
Instruction Manual Thank you for purchasing the HAKKO FM-2029 Hot Air Handpiece. Please read this manual before operating the HAKKO FM-2029. Keep this manual readily accessible for reference. CAUTION HAKKO
More informationInstruction Manual. For All Corning Hot Plates, Stirrers, Stirrer/Hot Plates with Digital Displays, and External Temperature Controller (6795PR)
Instruction Manual For All Corning Hot Plates, Stirrers, Stirrer/Hot Plates with Digital Displays, and External Temperature Controller (6795PR) Corning Cat. No. 230V 230V Model No. Product Top Plate Size
More informationC 46 K a d. Specifications EKMC K. Ver.1.1. Page: EKMC K. 1.Product Name. 2.Model Number. 3.Dimensions. Approved by.
1. VZ series Without lens type (170μA / Digital Output / High Sensitivity) 1 2.Model Number Element size 3.Dimensions 0.6 0.4 0.6 Top VIEW 0.6 0.6 0.4 Marking C46K 170101 Side VIEW 1 st Row 2 nd Row C
More informationPyroelectric Infrared Sensors
Pyroelectric Infrared Sensors Cat.No.S1E-8 for EU RoHS Compliant All the products on this catalog are complied with EU RoHS. EU RoHS is "the European Directive 011/65/EU on the Restriction of the Use of
More information1. Table of Contents VisiJet Materials Overview Disclaimer Ispropyl Alcohol (IPA) and Polypropylene Glycol
1. Table of Contents............................................................................................ 2 1.1 0.1 VisiJet Materials Overview............................................................................
More informationCooker Hood LA-72-CAN.
Cooker Hood LA-72-CAN EN www.luxairhoods.com WARNINGS Safety This equipment can be used by children aged 8 or more, people with physical, mental and sensory disabilities or inexperienced users it they
More informationPyroelectric Infrared Sensors
Pyroelectric Infrared Sensors Cat.No.S21E-7 for EU RoHS Compliant All the products on this catalog are complied with EU RoHS. EU RoHS is "the European Directive 2002/95/EC on the Restriction of the Use
More informationApplications PL- N Series Lens Type Sensor Type Serial Number
Proximity Sensors PL Pyroelectric Infrared Sensors Overview KEMET s Pyroelectric Infrared Sensors use the pyroelectric effect of ceramic by absorbing infrared rays emitted from the human body. This detects
More informationCLARA AC Crystal CLARA AC 50. LED-modules for downlight. A qualified solution to replace and exceed Halogen solutions in Downlights.
CLARA AC CLARA AC Crystal CLARA AC 50 LED-modules for downlight A qualified solution to replace and exceed Halogen solutions in Downlights. No Driver is required! Page 2 of 24 Designed for downlight and
More informationINSTRUCTION MANUALColours
3D SUBLIMATION VACUUM HEAT PRESS MACHINE 3D SUBLIMATION VACUUM HEAT PRESS MACHINE 3D SUBLIMATION VACUUM HEAT PRESS MACHINE A new generation of sublimation printing technology. These machines are multi-functional.
More informationThermal Devices, Inc. Mount Airy, Maryland USA C D E F. Typical Maxiband Clamping
Maxiband Heaters The Most Sought After Band Heater A B Maxiband General purpose terminal box offers excellent protection to the exposed terminals. To simplify electrical wiring, the box has two 1/2" trade
More informationEVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet Full Color Top View LEDs Features P-LCC-4 package. White package. Optical indicator. Colorless clear window. Pb-free The product itself will remain within RoHS compliant version. Descriptions
More informationReference Specification
Specification No. JELF243A-0040D Issued Date: Feb. 18, 2005 Reference Specification Part Description: CHIP COIL MURATA Part No: LQH32CN 33L RoHS regulation conformity parts. Technical Dept. Prepared by
More informationSECTION AUXILIARY HEATER
14-301.03/ 1 2010MR12 SECTION 14-301.03 GENERAL DESCRIPTION The Thermo 300 auxiliary heating system is used in conjunction with the vehicle s heating system, in order to heat the passenger compartment
More informationIonizer (Static Remover) STABLO-EX Instruction Manual
321-56879-21E Jan. 2009 For Electronic Balances Ionizer (Static Remover) STABLO-EX Instruction Manual Read the instruction manual thoroughly before you use the product. Retain this instruction manual for
More informationNo.THD51E To prevent accidents arising from the use of this product, please ensure the operator using it receives this manual.
Instruction manual Hygrothermo transmitter THD-500 Series No.THD51E1 2001.11 To prevent accidents arising from the use of this product, please ensure the operator using it receives this manual. Notes This
More informationA Specifications. Ver.1.1. Page: EKMC Product Name. Model Number. 3.Dimensions. Approved by. Checked by.
A745 Specifications 1 1. VZ series Horizontally wide detection type (170μA / Digital output ) 2.Model Number Lens Color White Black Pearl White Model Number 1 2 3 Marking 3.Dimensions Top VIEW Side VIEW
More informationVT-DESOL2 DESOLDERING STATION DESOLDEERSTATION STATION DE DESSOUDAGE ENTLÖTSTATION USER MANUAL GEBRUIKERSHANDLEIDING MANUEL D'UTILISATION
DESOLDERING STATION DESOLDEERSTATION STATION DE DESSOUDAGE ENTLÖTSTATION USER MANUAL GEBRUIKERSHANDLEIDING MANUEL D'UTILISATION GEBRAUCHSANLEITUNG : DESOLDERING STATION 1. Introduction Congratulations!
More information