VTCS evaporator block design and prototyping. Status report July 2004
|
|
- Elizabeth Welch
- 6 years ago
- Views:
Transcription
1 VTCS evaporator block design and prototyping Bart Verlaat, Luc van Diepen & Martin Doets (NIKHEF) Frans Mul (VU) 30-Jul-04 1
2 VTCS evaporator block design (1) Detail of cooling block mounted onto the VELO module Evaporator block is 30-Jul-04 situated underneath the module cables 2
3 VTCS evaporator block design (2) Evaporator header Ø6x1 pipe Orbital TIG weld Laser weld Ø1.5x0.25 pipe Aluminum cooling block 30-Jul-04 3
4 VTCS evaporator block design (3) 1. A NIKHEF/VU developed aluminum casting method allows embedded piping to be of any shape, with a full thermal contact over the entire pipe area. 2. Casting under vacuum (<10-4 mbar) gives that the aluminum is floating perfectly in the mould and sticks itself to the stainless steel pipes, by the formation of intermetallic phases. 3. A good thermal contact of the cooling block to the pipe is expected due to the following properties: The CTE difference of aluminum and stainless steel gives a strong crimping force of the block around the pipe No intermediate filing material with low thermal conductivity is needed (glue, solder, etc) around the pipe The aluminum tends to stick to the stainless steel pipes when melted under vacuum (See note 2). 30-Jul-04 bverlaat@nikhef.nl 4
5 30-Jul-04 5
6 Cooling block connection detail Aluminum potting in the paddle base top area makes the laminate symmetric to minimize bi-metal forces. 30-Jul-04 6
7 VTCS evaporator block prototyping Optimal process parameters (So far known): Evacuate the vacuum chamber before heating Setting the oven to be 700 C for 1 hour After sensor in casting mould has reached 700 C the Argon is inserted (oven time is approx. 30 minutes) Solidifying is obtained with a closed oven Melting under vacuum and solidifying under Argon gives the best results Perfect floating of the aluminum in the mould Aluminum / Stainless steel sticking Magnesium containing alloys seemed unusable due the vaporizing of the magnesium under vacuum conditions, but applying pressure after the melting eliminates most of the vapor bubbles. The bottom part (Which is the final part) shows the best results. Optimal material (so far) is AL99.5 or AlMg4.5Mn. 30-Jul-04 bverlaat@nikhef.nl 7
8 Oven Vacuum vessel Vacuum/Argon Inlet Control Casting mould with cooling pipes Casting set-up in vacuum vessel Vacuum pump 30-Jul st Prototype cooling block casting set-up
9 1 st Prototype casted aluminum cooling block Cooling block is machined after casting process 1 st prototype is melted and solidified under vacuum Magnesium vapor bubbles 30-Jul-04 bverlaat@nikhef.nl 9
10 2 nd Prototype casting block mounted on a prototype module Cooling block 2 nd prototype is melted under vacuum and solidified under 1 bar Argon In & outlet tube 30-Jul-04 bverlaat@nikhef.nl 10
11 Detail of the casted evaporator block. The shown side is the molded side, which needed no post machining. 30-Jul-04 11
12 Due to the possibility of free forming the embedded tube, a new cooling block is under investigation. This block has 5 separate cooling blocks casted to the pipe in 1 casting cycle. The separation shall eliminate the forces in the module occurred by the differences in CTE. The production of a prototype of this cooling block is ongoing. The mounting interface is the same for both designs. The disadvantage of this cooling block is worse thermal performance as the strait version. Also handling seems less practical. 30-Jul-04 bverlaat@nikhef.nl 12
DESIGN, MANUFACTURE AND TEST RESULTS OF THE VTCS CO 2 EVAPORATOR FOR THE LHCB EXPERIMENT AT CERN.
HEFAT2010 7 th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics 19-21 July 2010 Antalya, Turkey DESIGN, MANUFACTURE AND TEST RESULTS OF THE VTCS CO 2 EVAPORATOR FOR THE LHCB
More informationCO 2 COOLING FOR THE LHCB-VELO EXPERIMENT AT CERN.
GL2008 8 th IIF/IIR Gustav Lorentzen Conference on Natural Working Fluids 7-10 September 2008 Copenhagen, Denmark Paper number: xxx CO 2 COOLING FOR THE LHCB-VELO EXPERIMENT AT CERN. B. Verlaat*, A. Van
More informationCooling test results C-side replacement detector
Cooling test results C-side replacement detector Nikhef number: Item number: Date: 2/10/2011 Page: 1 of 36 39300-MT-00003 AA2232 Status: In Work Revision: A.5 Project: LHCb VELO Department: Mechanical
More informationPoS(Vertex 2007)009. CO 2 cooling experience (LHCb) Martin van Beuzekom, Ann Van Lysebetten 1, Bart Verlaat
CO 2 cooling experience (LHCb) Martin van Beuzekom,, Bart Verlaat Nikhef Kruislaan 409, 09 SJ Amsterdam, The Nerlands E-mail: Ann.Van.Lysebetten@cern.ch The rmal control system of LHCb Vertex LOcator (VELO)
More informationHandling units for. Technobis Mechatronics has developed and manufactured three mechatronic handling units
Mechatronic design for high-temperature operation Handling units for Technobis Mechatronics has developed and manufactured three mechatronic handling units for harsh environments. These units are part
More informationTRACI, A MULTIPURPOSE CO 2 COOLING SYSTEM FOR R&D
Paper No: GL-208 RACI, A MULIPURPOSE CO 2 COOLING SYSEM FOR R&D B. Verlaat(a,b), L. Zwalinski(b), R. Dumps(b), M. Ostrega(b,c), P. Petagna(b) and. Szwarc(b,c) (a) National Institute for Subatomic Physics
More informationHIGH QUALITY VAPOR PHASE REFLOW SOLDERING. SMTA Arizona-Sonora December 4th 2012
HIGH QUALITY VAPOR PHASE REFLOW SOLDERING THE ADVANCED SOFT SOLDERING TECHNOLOGY SMTA Arizona-Sonora December 4th 2012 IBL Reflow soldering is a complex physical and chemical process. The demand of lead
More informationLeading Safety Standards Superior Ease of Use Reduced Cost of Ownership. Intelligent. Evaporation
Leading Safety Standards Superior Ease of Use Reduced Cost of Ownership Intelligent Evaporation Leading Safety Standards Two independent safety circuits avoid an overheat situation of your heating bath:
More informationMechanical Vacuum Systems for Secondary Metallurgy Steel Degassing
Mechanical Vacuum Systems for Secondary Metallurgy Steel Degassing 173.13.02 Utmost Efficiency VD / VOD processes Vacuum Degassing (VD) for low alloy steels; Vacuum Oxygen Decarburising (VOD) for stainless
More informationAdapted Systems for Zinc and Magnesium
Frech Gating System in Application 65,39 30 Zn Zink 7,14 24,31 12 Mg 1,74 Magnesium Adapted Systems for Zinc and Magnesium 1 FGS-Systems For Magnesium Reduction of high remelting costs for magnesium! Shortest
More informationHow To Make Lando Water Chillers? Leading the way of innovation. Here is the instruction to know more us how to
How To Make Lando Water Chillers? Leading the way of innovation Here is the instruction to know more us how to make hydroponic water chillers, aquarium water chillers, industrial water chillers. 2014/1/8
More informationCO 2 Cooling Seminar Desy Hamburg
bverlaat@nikhef.nl bverlaat@nikhef.nl CO 2 Cooling Seminar Desy Hamburg Bart Verlaat (Nikhef/CERN) 18 February 211 1 CO 2 Cooling Seminar The benefits of using CO 2 cooling. History of CO 2 cooling. Introduction
More informationLoop Heat Pipe Wick Fabrication via Additive Manufacturing
47th 16-20 July 2017, Charleston, South Carolina ICES-2017-12 Loop Heat Pipe Wick Fabrication via Additive Manufacturing Bradley Richard 1, Devin Pellicone 2, and Bill Anderson 3 Advanced Cooling Technologies,
More informationEBAC MODEL K100 DEHUMIDIFIER OWNER S MANUAL
EBAC MODEL K100 DEHUMIDIFIER OWNER S MANUAL Ebac Industrial Products 700 Thimble Shoals Boulevard Newport News VA 23606-2575 Telephone (757) 873-6800 Fax (757) 873-3632 Website: www.ebacusa.com INTRODUCTION
More informationSystem Level Design Review. P16420: Lip Balm and Hand Salve Process Improvement
System Level Design Review P16420: Lip Balm and Hand Salve Process Improvement Agenda Team Introduction Problem Definition Review Benchmarking Functional Decomposition Product Architecture Concept Generation
More informationVACUUM & PRESSURE PRODUCTS. Plastics Industry
VACUUM & PRESSURE PRODUCTS Plastics Industry Conveying & Drying Pellet Conveying Pellets are conveyed through extensive pipe networks Conveyed under vacuum (dense phase) or pressure (dilute phase) G-Series
More informationThermal Devices, Inc. Mount Airy, Maryland USA
Developing Solutions Through Product Innovation Tempco is a name synonymous with state-of-the-art technology and a strong commitment to providing practical, cost effective, quality thermal component solutions.
More informationSection N. Application Information. Thermal Manufacturing Solutions. Extrusion N-1. Injection Moulding N-2 N-3. Other N-4
Thermal Manufacturing Solutions Section N Application Information Extrusion Injection Moulding Other Electrical Heating Of Plastic Injection Molds Heating And Cooling Of Cores Electrically Heated Platens
More informationTHE NEW GENERATION VACUUM PUMP SYSTEM SC
THE NEW GENERATION VACUUM PUMP SYSTEM SC 920 with wireless remote control Fast and precise from afar: Vacuum pump system with wireless remote control The new vacuum pump system SC 920 now supports remote
More informationOperational aspects of the VELO cooling system of LHCb
Operational aspects of the VELO cooling system of LHCb Eddy Jans (Nikhef) on behalf of the LHCb VELO group Introduction Main components and operation principle of the system Issues: how to prevent and
More information上海久信机电设备制造有限公司 Shanghai Joysun Machinery & Electric Equipment Manufacture Co., Ltd
www.joysun-machinery.com 上海久信机电设备制造有限公司 Shanghai Joysun Machinery & Electric Equipment Manufacture Co., Ltd Sino-foreign joint venture Shanghai Joysun Machinery & Electric Equipment Manufacture Co., Ltd
More informationSIGMAWIG ALL WELDED PLATE HEAT EXCHANGERS
SIGMAWIG ALL WELDED PLATE HEAT EXCHANGERS 313 SIGMAWIG opens up new fields of application SIGMA plate heat exchangers are recognized worldwide for quality and reliability in thermal processes such as cooling,
More informationFlexibility Plus Power: The New Large-Area Vacuum Gripping System FMP/FXP
World of Vacuum Technology Flexibility Plus Power: The New Large-Area Vacuum Gripping System FMP/FXP Product Presentation 05/2013 Agenda Schmalz Area Grippers: A Look Back State of the Art: Area Gripper
More informationHeated tools. Semiconductor equipment
Heated tools Semiconductor equipment Ceramic heating elements made of silicon nitride and aluminum nitride can be manufactured as tools in various shapes. The heating function can be integrated in complex
More informationIn-class disassembly exercise
In-class disassembly exercise Students dismantle obsolete computer keyboards, telephones or like-size objects, preferably of different makes and dates (such as IBM and Apple). Instructor and students bring
More informationOerlikon Ebeam Evaporator SOP short. UNT Cleanroom
Oerlikon Ebeam Evaporator SOP short UNT Cleanroom 1. Transfer sample holder into process chambers: Log in FOM to access the software Go to the software and log in with user1 and password user1 Go to transport
More informationStrip/Clamp-On Heaters
Max. Operating Typical Max. Temperatures Watt Densities Strip/Clamp-On Heaters Sheath Materials F C W/in 2 W/cm 2 Page Mineral Insulated (MI) 304 stainless steel 1400 760 140 21.7 477 375 High-Temperature
More informationVACUUM FOR HIGHER QUALITY. In pressure die casting
VACUUM FOR HIGHER QUALITY In pressure die casting VACUUM THE EVACUATION GENIUS Our principle Research & Development 500 In pressure die casting since lling a ca ity ith an alloy takes a short time, vacuum
More informationReflow Soldering Guidelines
Reflow Soldering Guidelines for Surface-Mount Devices January 1998, ver. 2 Application Note 81 Introduction Altera s surface-mount products include quad flat pack (QFP), ceramic and plastic J-lead chip
More informationLeading Safety Standards Superior Ease of Use Reduced Cost of Ownership. Intelligent. Evaporation
Leading Safety Standards Superior Ease of Use Reduced Cost of Ownership Intelligent Evaporation Leading Safety Standards Newly designed EASY LOCK flask attachment allows for safe flask change An emergency
More informationIntelligent. Evaporation.... no task too big
Intelligent Evaporation... no task too big While you concentrate on research, we ll look after your support needs As we want you to have more time to thoroughly concentrate on research, the whole Heidolph
More informationHEAT PIPES
HEAT PIPES * Shaikh Naushad, Design Engineer PTC, Communication Concept, Saudi Arabia INTRODUCTION A heat pipe is a device that efficiently transports thermal energy from its one point to the other. It
More informationTechnical specifications cryoair cryotherapy chamber
Technical specifications cryoair cryotherapy chamber 3 chamber system 110 C Elite Médicale ZI NORD 22 rue André Durouchez 80080 AMIENS Tél: 03 22 67 54 54 Fax: 03 22 67 54 55 Email: accueil@elitemedicale.fr
More informationISO INTERNATIONAL STANDARD. Liquid hydrogen Land vehicle fuel tanks. Hydrogène liquide Réservoirs de carburant pour véhicules terrestres
INTERNATIONAL STANDARD ISO 13985 First edition 2006-11-01 Liquid hydrogen Land vehicle fuel tanks Hydrogène liquide Réservoirs de carburant pour véhicules terrestres Reference number ISO 13985:2006(E)
More informationProtecting small-scale herbarium collections from attack by insects and moulds
Protecting small-scale herbarium collections from attack by insects and moulds Jerry A. Cooper Fungal Network of New Zealand January 2012 The work of non-professional mycologists is an important global
More informationAdditional Cooling Stage (FT174-43) Adds the location points and plumbing for a fourth heat exchanger.
Modules, Options and Accessories Options (to be defined at time of order) Flowmeter Option (FT174-40) The standard unit displays an estimated flow rate calculated from the feed pump speed. This is accurate
More informationIntroduction to Pharmaceutical Freeze Drying
Introduction to Pharmaceutical Freeze Drying David Debo, PE Date 1 Agenda Introduction Stages of the process System components 2 Introduction What is lyophilization? What is sublimation? Why freeze dry?
More informationIntelligent. Evaporation. Premium Safety Standards Superior Ease of Use Reduced Cost of Ownership
Intelligent Evaporation Premium Safety Standards Superior Ease of Use Reduced Cost of Ownership Premium Safety Standards Protect yourself reliably with safety models: a guard hood consisting of a metal
More informationLoop Heat Pipe Radiator Trade Study for the K Temperature Range
Loop Heat Pipe Radiator Trade Study for the 300-550 K Temperature Range William G. Anderson 1 and Walter Bienert 2 1 Advanced Cooling Technologies, 1046 New Holland Ave., Lancaster, PA 17601 2 Consultant,
More informationSMT Quick-Tips: selecting a reflow oven. Robert Voigt, DDM Novastar
SMT Quick-Tips: selecting a reflow oven Robert Voigt, DDM Novastar Selecting A Reflow Oven There are several different reflow methods to liquefy solder in a controlled way and not all of them can literally
More informationHG DI
Sample Preparations 1. Leica CM1950 Cryostat 2. Hirayama HV-85 Autoclave 3. Hirayama HG-80 Autoclave 4. Freeze Dryer 5. Vacuum Oven 6. Sputtering Machine 7. Ultracentrifuge 8. Deep Freezer 9. DI & Ultra
More informationAlpha 355S / Alpha 356. Multifunctional automatic crimping machines
Alpha 355S / Multifunctional automatic crimping machines THE WAY TO MAKE IT FLEXIBLE With their open architecture, the Alpha 355S and have a wide variety of applications. Besides Komax standard processing
More informationMODULAR COOKING EVO900
MODULAR COOKING EVO900 GREAT MODULARITY ACCORDING TO ZANUSSI Evo900 is the great Zanussi Professional modular choice. Top performance, excellent reliability and highly robust: all designed for a kitchen
More informationHeat sinks for electronic cooling applications
Heat sinks for electronic cooling applications Shubhash V. Jadhav Department of Mechanical Engineering, SVERI s College of Engineering Pandharpur, Introduction The previous century brought the miniaturization
More informationBuehler Cast N Vac 1000 Embedding System
Buehler Cast N Vac 1000 Embedding System Standard Operating Procedure Revision: 1.0 Last Updated: Nov 17 2016, Revised by Matt Bilton Overview This document will provide a detailed operation procedure
More informationReliable processes with and without vacuum
Reliable processes with and without vacuum Reflow Condensation Soldering with unique technology benefits CondensoXC Condensation Soldering Condensation Soldering Innovative solution from Rehm CondensoXC
More informationVacuum furnaces with gas cooling/ gas quenching
Vacuum furnaces with gas cooling/ gas quenching Vacuum furnaces for hardening, brazing, tempering, annealing Your application defines the furnace design Your application defines how the furnace should
More informationExtrusion Walkthrough
Extrusion Walkthrough Our experiences with the extrusion of polyethylene terephthalate (PET). Contents The Extrusion of PET... 2 Shredding PET... 2 Shredding PET... 3 Starting up... 3 Cleaning the extruder...
More informationEgg handling. Picking up and opening bags. Vacuum molding of plastic products. Instrument control for aircraft and vehicles
Egg handling With suction cups and a vacuum, eggs and other easily damaged products can be handled without risk, simply and conveniently. Picking up and opening bags Bellows suction cups are ideal for
More informationSoldering of Lead Free Solders in Vapour Phase
Soldering of Lead Free Solders in Vapour Phase Heat Transfer Heat Transfer Coefficient Free Convection Gas 3 30 Water 100 1000 IR Reflow 50 100 Forced Convection 30 120 Vapour Phase reflow 400 700 Formation
More informationLeading Safety Standards Superior Ease of Use Reduced Cost of Ownership. Intelligent. Evaporation
Leading Safety Standards Superior Ease of Use Reduced Cost of Ownership Intelligent Evaporation Leading Safety Standards Newly designed EASY LOCK flask attachment allows for safe flask change An emergency
More informationREFLOW OVEN FT01 Version REFLOW OVEN FT01. (Article number F31105) User s Manual
www.cif.fr REFLOW OVEN FT01 (Article number F31105) User s Manual This document contains manufacturer s information which is protected by copyright. All rights reserved. This document cannot be copied,
More informationGeneral. Applications and Accessories for Oil Diffusion Pumps. leybold. Application. Accessories LEYBOJET 630 DIP DIP DIP DIP 30000
General Applications and Accessories for Oil Diffusion Pumps Pumps Application DIP 3000 DIP 8000 DIP 12000 DIP 20000 DIP 30000 DIP 50000 Vacuum coating Research and development Metallurgy/furnaces Mechanical
More informationFORCED AIR CONVECTION THERMAL SWITCH CONCEPT FOR RESPONSIVE SPACE MISSIONS
FORCED AIR CONVECTION THERMAL SWITCH CONCEPT FOR RESPONSIVE SPACE MISSIONS 6 August 26 2 th AIAA/USU Small Sat Conference Andrew D. Williams Air Force Research Laboratory, Space Vehicles Directorate Kirtland
More informationCeramic Fiber Heaters
Introduction High Temperature Ceramic Fiber Heaters Design Features Standard Heaters to 1100 C (2012 F) High Temperature Version to 1200 C (2192 F) Low Thermally Conductive Built-In Insulation Standard
More informationD r ying printed circuit boards
D r ying printed circuit boards G. Schuber t, Th. Schönfeld, A. Friedrich, SMT & HYBRID GmbH 1. Introduction printed circuit boards as moisture-sensitive components The following aims lie behind the investigations
More informationNRF PDMS Processing SOP 2/12/18 Rev 2 Page 1 of 9. NRF PDMS Processing SOP
Rev 2 Page 1 of 9 NRF PDMS Processing SOP Table of Contents 1. PDMS Processing Tools available at the NRF 2. Fabrication of Master Molds 3. Mixing and Preparing the PDMS 4. PDMS Master Surface Preparation
More informationSafety Analysis of the 3 main parts in the CO2 system
Safety Analysis of the 3 main parts in the CO2 system Nikhef number: Item number: Date: 11/11/2010 Page: 1 of 38 39300-MT-00001 AA1578 Status: In Work Revision: A.3 Project: Department: Mechanical Technology
More informationTubular Heaters Series
Tubular Heaters Series Immersion Heaters, Tubular Heaters, Ribbed Tubular Heaters Screw-in Immersion Heater Standard sizes for application in water Power (W) 2000 000 4500 6000 7500 Input Voltage (V) 20
More informationStable High Vacuum. Oil diffusion pumps Oil vapor jet pumps
Stable High Vacuum Oil diffusion pumps Oil vapor jet pumps 174.11.02 High vacuum with The oil diffusion pumps and oil vapor jet pumps from Leybold are rugged, provide a long service life and excel through
More informationLaser Damage Measurements
Laser Damage Measurements Mathias Hüther Max-Planck-Institute for Physics, Munich huether@mpp.mpg.de April 08, 2016 Workshop Laser plasma generation for particle acceleration at Wigner Research Center
More informationFuel Cell Stack CVM Chip Solder Joint Structural Analysis with ANSYS Sub-Modeling Technique
Fuel Cell Stack CVM Chip Solder Joint Structural Analysis with ANSYS Sub-Modeling Technique Kemal Ozgur, Ph.D., P.Eng. Senior Engineer Ballard Power Sysems John Kenna Manager, Product Development Ballard
More informationHot Reservoir Stainless-Methanol Variable Conductance Heat Pipes for Constant Evaporator Temperature in Varying Ambient Conditions
Joint 18th IHPC and 12th IHPS, Jeju, Korea, June 12-16, 2016 Hot Reservoir Stainless-Methanol Variable Conductance Heat Pipes for Constant Evaporator Temperature in Varying Ambient Conditions Jens Weyant
More informationVACUUM FOR HIGHER QUALITY. In plastic injection molding
VACUUM FOR HIGHER QUALITY In plastic injection molding A FASCINATION FOR VACUUM Pioneering spirit Founded in 1946 in Switzerland, Fondarex is the inventor of the vacuum technology for pressure die casting
More informationHeat Exchanger- Lockheed Martin
1 Heat Exchanger- Lockheed Martin Engineering Design 100, Section 22, Dr. Ritter Team 4, MODZ Zeping (Calvin) Cheng (zbc5056@psu.edu), Olivia Connors (ojc5027@psu.edu), Madison Powers (mlp5514@psu.edu),
More informationESD, SPECIAL AND VERTICAL MACHINES
2 ESD, SPECIAL AND VERTICAL MACHINES ESD-MACHINES MAX 42 VA 420 410 internal chamber dimensions 450 x x 230 mm* seal length 420 mm vacuum pump 21 m 3 /h external dimensions 0,54 x 0,65 x 0,41 m* weight
More informationCondensing Unit Installation and Operating Instructions
Bulletin ACU_O&I 02 August 2016 Condensing Unit Installation and Operating Instructions ACU Air Cooled Condensers Table of Contents Section 1. General Information... 2 Section 2. Refrigeration Piping...
More informationwith control panel Hobs + Hobs The A Z of Gaggenau hobs and hobs with control panels
29 The A Z of Gaggenau hobs and hobs with control panels Appliance depth 4 cm A not insignificant factor in kitchen design, the minimal depth of many Gaggenau hobs saves space and simplifies installation
More informationHEATING SOLUTIONS PACKAGING MACHINES
HEATING SOLUTIONS PACKAGING MACHINES CARTRIDGE FOIL THICK FILM WE MAKE IT HAPPEN Heating solutions Backer Calesco has the experience, knowledge and capabilities to help you develop and manufacture heating
More informationWELCH INDUSTRIES - PAGE 1 OF 5
MCI 9, 96A & 102 RE-2 Auxiliary Installation Look over all components in order to familiarize yourself with the complete system. The compressor mounts over the gear-box between radiators, driven by the
More informationPouch Cell Li-ion Batteries Pilot Line
Battery Type: 1. M Type and Z Fashion Stacking Pouch Cell Battery 2. M Type Battery Pack Overview: Standard M Type Electrodes and Separator Dimensions: 1. Battery Cell: T 6 mm x W 85 mm x H 120 mm; 2.
More informationLeak testing in the HVACR Industry
Leak testing in the HVACR Industry Applications for Component Manufacturing and Final Testing QUALITY ASSURANCE IN THE AUTOMOTIVE INDUSTRY Reliable, accurate tools for any of your leak detection tasks
More informationSINGLE COMPACT DISC METALLIZATION TYPE SINGULUS III / 3
Revision Date: 10. March 1999 TECHNICAL SPECIFICATION SINGULUS III / 3 SPECIFICATION NO. 010696 PRODUCTION SYSTEM PREPARED FOR SINGLE COMPACT DISC METALLIZATION TYPE SINGULUS III / 3 SINGULUS TECHNOLOGIES
More informationHERMS (Heat Exchanger Recirculating Mash System) Controller
HERMS (Heat Exchanger Recirculating Mash System) Controller Your new HERMS controller Thanks for buying your controller from us!!! Your controller is based on two MYPIN TA4 series PID controllers. Unlike
More informationExperiences and Challenges in Pumping the 200m3 vacuum chamber at JET
Experiences and Challenges in Pumping the 200m3 vacuum chamber at JET T. Coyne 1*, N. Balshaw 1,S. Davies 2 1 JET-EFDA. Culham Science Centre, Abingdon, OX14 3DB. UK. 2 Hiden Analytical Ltd. 420 Europa
More informationInternal chamber dimensions 285 x 350 x 105 / 150 mm* Seal length 260 mm Vacuum pump 4 m 3 /h 8 m 3 /h
1 1 VACUUM PACKING MACHINES TABLETOP MACHINES MINI MINI MAX 260 300 Internal chamber dimensions 285 x 350 x 105 / 150 mm* Seal length 260 mm Vacuum pump 4 m 3 /h 8 m 3 /h External dimensions 0,36 x 0,49
More informationVACUUM FOR HIGHER QUALITY. In plastic injection molding
VACUUM FOR HIGHER QUALITY In plastic injection molding CONTENT COMPANY PIONEERING SPIRIT / HISTORY 3 TECHNOLOGY OUR PRINCIPLE / RESEARCH & DEVELOPMENT 6-7 OUR PERFORMANCES / YOUR ADVANTAGES 8-9 PRODUCTS
More informationMink MV. Claw Vacuum Pumps for Rough Vacuum Industrial Applications. Claw Vacuum Technology by Busch
for Rough Vacuum Industrial Applications Dry Vacuum Quiet, Efficient and Compact Product Overview Series Type Latest Claw Vacuum Technology Quiet: lowest noise level due to a state-of-the-art acoustic
More informationTrial decision T.RAD CO. LTD. KUBOTA, Takubi DENSO CORPORATION
Trial decision Invalidation No. 2014-800124 Tokyo, Japan Demandant T.RAD CO. LTD. Tokyo, Japan Patent Attorney KUBOTA, Takubi Aichi, Japan Demandee DENSO CORPORATION The case of trial regarding the invalidation
More informationAir-Cooling Evaporators
Air-Cooling Evaporators Types of construction Circuit Configurations Methods of Refrigerant Feed Methods of Air Circulation Methods of Defrost Type of Construction Bare tube Finned Tube Plate-surface Bare
More informationManual Physical Vapour Deposition System
Manual Physical Vapour Deposition System Wilhelmus Geerts, Debbie Koeck. 1.0 Content: Manual explaining how to operate the system. Background explaining the deposition technology. Trouble-shooting / FAQ.
More informationManufacturing Notes for RFPA2016
Manufacturing Notes for RFPA2016 The information in this publication is believed to be accurate and reliable. However, no responsibility is assumed by RF Micro Devices, Inc. ( RFMD ) for its use, nor for
More informationInduction cooking has been used in Europe for decades
HIGH CLEAR O OFF Planning Information Available October 2007 Five induction elements Melt setting Electronic touch controls Countdown timer Universal OFF key Model CT36I/S SIM HIGH OFF ON MELT OFF ON HIGH
More informationAdvantages / Characteristics
Air to Air 50 W 30 W cooling capacity 163x104x144mm (LxBxH) 1,9 kg Air to Air 70 W 36 W cooling capacity 163x104x144mm (LxBxH) 1,9 kg Air to Air 75 W 30 W cooling capacity 130x109x163mm (LxBxH) 1,5 kg
More informationSECTION (15530) - REFRIGERANT PIPING
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Tubes. 2. Fittings. SECTION 23 23 00 (15530) - REFRIGERANT PIPING 3. Joining Materials. 4. Specialties. B. Related Sections: 1.02 REFERENCES 1. Section
More informationBINDER Scientific Product Catalog
BINDER Scientific Product Catalog 36 Vacuum drying ovens Vacuum drying ovens 37 VD VDL VDL EX-Zone 2 Absolutely reliable drying Drying with no residues, no danger of incrustation, no oxidation all under
More information.2 Section Waste Management and Disposal.
Issued 2005/06/01 Section 15624 Packaged Rotary Screw Water Chillers Page 1 of 5 PART 1 General 1.1 RELATED SECTIONS.1 Section 01330 Submittal Procedures..2 Section 01355 Waste Management and Disposal..3
More informationVacuum and Pressure Solutions for the Plastics Industry
Vacuum and Pressure Solutions for the Plastics Industry Elmo Rietschle. Leading the Field. Why Elmo Rietschle? From our point of view, of course, we see many reasons why you should work with our company
More informationEVALUATING LOOP HEAT PIPE PERFORMANCE IMPROVEMENT USING CIRCUMFERENTIAL GROOVES. Nadjara dos Santos, Roger R. Riehl
Abstract EVALUATING LOOP HEAT PIPE PERFORMANCE IMPROVEMENT USING CIRCUMFERENTIAL GROOVES Nadjara dos Santos, Roger R. Riehl National Institute for Space Research INPE - Space Mechanics and Control Division-DMC
More informationRotavapor R-220 SE Technical data sheet
otavapor Technical data sheet The otavapor is designed to fulfill a wide range of distillation applications in the industrial environment. Safety, robustness and easy handling are the key benefits of this
More informationRFFM6403. Manufacturing Notes. Table of Contents
RFFM6403 Manufacturing Notes Table of Contents The information in this publication is believed to be accurate and reliable. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for
More informationThermal Performance of a Loop Thermosyphon
Tamkang Journal of Science and Engineering, Vol. 13, No. 3, pp. 281 288 (2010) 281 Thermal Performance of a Loop Thermosyphon Shung-Wen Kang*, Meng-Chang Tsai, Chih-Sheng Hsieh and Jian-You Chen Department
More informationRotary Evaporators, Heidolph
Rotary Evaporators, Heidolph General properties of the Laborate 4000 series Safety Control panel is below the handles for the heating bath, for protection from vapour and splashes All heating baths have
More informationManufacturing Notes for RFDA0025
Manufacturing Notes for RFDA0025 The information in this publication is believed to be accurate and reliable. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for
More informationCO 2 cooling for HEP experiments
CO cooling for HEP experiments B. Verlaat, M. Van Beuzekom, A. Van ysebetten Nikhef, Kruislaan 49, 198 SJ Amsterdam, The Netherlands bverlaat@nikhef.nl Abstract The new generation silicon detectors require
More informationINSTALLATION INSTRUCTIONS PT-A HEAT/AC STANDARD KIT FORD E-SERIES VANS
INSTALLATION INSTRUCTIONS PT-A-402 - HEAT/AC STANDARD KIT 2007-2014 FORD E-SERIES VANS with Gas engine (To be used with 2007 and newer Prisoner Transport Inserts ONLY) Warning do not attempt to install
More information(12) United States Patent (10) Patent No.: US 7,654,310 B2. Li (45) Date of Patent: Feb. 2, 2010
USOO765431 OB2 (12) United States Patent (10) Patent No.: Li (45) Date of Patent: Feb. 2, 2010 (54) LOOP HEAT PIPE 6,840,304 B1* 1/2005 Kobayashi et al.... 165,111 7,231,961 B2 * 6/2007 Alex et al....
More informationHelium Leak Detection Systems
Helium Leak Detection Systems Best-in-class Technology for your Quality Assurance. Custom. Cost-effective. Efficient. Helium Leak Detection Systems The efficient system for your application Are you looking
More informationKurt J. Lesker in the Cryogenic Community. Dr. Glynn Dyson Cryogenics Cluster Day 19 th September 2014
Kurt J. Lesker in the Cryogenic Community Dr. Glynn Dyson 19 th September 2014 Overview Introduction to the Kurt J. Lesker Company (KJLC) KJLC in the Cryogenic Community Deposition Methods Axxis Coating
More informationFlammable Liquid: A liquid whose flashpoint is greaterless than 100 F when tested by closed-cup test methods.
ANSI/IIAR 2-2014 Addendum A Standard for Safe Design of Closed-Circuit Ammonia Refrigeration Systems Public Review Draft #3 Reviewers of Addendum A are welcome to comment on the changes in the standard,
More information