Parts checklist. e f g. How to operate FRONT VIEW REAR VIEW

Transcription

1 Parts checklist n b c d 2 a m l j i g h e f REAR VIEW k FRONT VIEW a b c d e f g Handle Clean solution tank latch On/Off switch Power cord Dirty water tank latch Drain cap Vacuum/Scrub selector h i j k l m n Dirty water tank Rotating scrub brush Vacuum nozzle Spray nozzle Cord wrap Spray trigger Clean solution reservoir How to operate Grasp solution tank handle and press the clean solution tank latch. Slide the solution tank away from the cleaner until the tabs on the tank are disengaged from the slots on the cleaner. Lift the clean solution tank to remove.

2 How to operate cont Unscrew the cap from the back of the clean solution tank. Fill the solution tank with 15ml of Vax AAA carpet cleaner. Slowly fill the remainder of the clean solution tank with warm (max 40ºC) water. How to operate cont Correct Incorrect Replace the cap. Line up the tabs on the clean solution tank with the slots on the the cleaner and slide the tank toward the cleaner. Make sure the clean solution tank is aligned properly. Note: Failure to install the clean solution tank correctly will result in poor dirty water pick-up.

3 Carpet/upholstery cleaning Plug cord into an electrical socket. Turn the power switch ON. Turn the Vacuum/Scrub selector knob towards Vacuum and remove as much liquid as possible from the spill or spot. Carpet/upholstery cleaning cont Depress the spray trigger to spray solution onto the area. Allow the cleaning solution to penetrate stain for 2 minutes. Turn the Vacuum/Scrub selector to Scrub and use the rotating scrub brush on the area in a forward and backward motion, using steady strokes. Turn the Vacuum/Scrub selector back to Vacuum to pick-up the remaining moisture.

4 Emptying & cleaning the dirty water tank 8 Note: Do NOT remove the dirty water tank with the unit in the upright position. You should empty the tank when the dirty water in the tank reaches the Full line on the dirty water tank, or, when the float shuts off airflow, this will be indicated by a change in the pitch of the motor and reduced suction. Finally, you should also empty the dirty water tank after use and rinse clean, before storage With one hand hold the cleaner by the handle, with the other grasp the sides of the dirty water tanks and push the latch to release. Grasp and pull the cleaner UP and AWAY from the dirty water tank. Unscrew the dirty water tank drain cap. Emptying & cleaning the dirty water tank cont. 4 Cleaning the dirty water tank Cleaning the filter 9 Empty the dirty water tank into the sink and replace the cap. 1. Rinse the dirty water tank with warm (max 40ºC) tap water. 2. Dry thoroughly before storing to prevent mildew from forming. Check the filter located on top of the dirty water tank periodically and clean by rinsing with water when dirty. Note: Make sure to replace the filter after cleaning.

5 Returning the dirty water tank to the base of the cleaner How to store the cleaner Cord Wrap Grasp the handle and hook the front of the dirty water tank securely into the base of the cleaner. The dirty water tank has 2 tabs on the underside, which MUST latch into the underside of the base of the cleaner. While making sure the front of the dirty water tank is hooked on the base, push the rear of the tank into the base of the cleaner and push down until it latches. The dirty water tank will need to be emptied once or twice per fill up of the clean solution tank. Note: Failure to install the dirty water tank correctly will result in poor dirty water pickup. Lift up the cord wrap and use it to secure the cord as it wraps around the cleaner. Troubleshooting Problem Cleaner won t run Possible Cause Power cord not firmly pushed into a mains socket. Blown fuse or tripped circuit breaker. Needs service. Possible solution Plug cord in firmly. Check fuse/breaker. Replace fuse or reset breaker. Call Vax Care Cleaner won t pick up or low suction Dirty water tank is not installed correctly. Dirty water tank is full. Review dirty water tank removal and replacement. Empty the dirty water tank. 11 Water escaping from the Cleaner Cleaner won t dispense solution Dirty water tank is full. Dirty water tank is not installed correctly. Solution tank not installed correctly. Spray nozzle clogged Solution tank not installed properly Empty the dirty water tank. Review dirty water tank removal and replacement. Review solution tank installation. Clean thoroughly. Review solution tank installation.

6 Safety 12 Do not leave the appliance when plugged in. Unplug it from socket when not in use. Not to be used outdoors. Not to be used as a toy. Close supervision is necessary when used by or near children or the infirm. Use only as described in this easy guide. Do not use with a damaged cord or plug. If the supply cord/plug is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard. Do not pull or carry by the cord, use the cord as a handle, allow the cord to come into contact with hot or sharp surfaces or close a door on the cord. Do not unplug by pulling on the cord. Do not handle the plug or appliance with wet hands. Do not put any objects into openings or operate with openings blocked, keep them free of anything that may reduce airflow. Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts. Do not vacuum any glowing, burning or smoking particles. Turn off all controls before unplugging. Do not use to pick up flammable or combustible liquids such as petrol, or use in areas where they may be present. Do not use an extension cord with this handheld vacuum cleaner. Do not attempt to remove blockages with sharp objects as they may cause damage. Store the handheld carpet washer indoors. Put the handheld carpet washer away after use to prevent tripping accidents. Do not place small objects or body parts in or around the rotating scrub-brush. Use only Vax AAA carpet cleaner. This handheld carpet washer is intended for domestic use only. For further information in the UK, call the VAX HELPLINE : This page has been left intentionally blank

7 EEC STATEMENT OF COMPLIANCE Manufacturer/EEC importer: VAX Limited, hereby on our own responsibility declare that the product: V-035 Spot Scrubber is manufactured in compliance with the following; Safety: 73/23/EEC Low Voltage Directive as modified by 93/68/EEC EMC: 89/336/EEC Electromagnetic compatibility Directive as modified by 93/68/EEC Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK. - website: Version 1 V-035 Easy Guide Handheld Carpet Washer UK SERVICE & HELP - VAX CARE Mon-Fri. 9.00am to 5.00pm. An answer phone is available out of these hours. If you have queries or concerns about using your VAX, call the HELPLINE. Calls are charged at the UK national rate. Please make a note of the serial number and model number of your VAX before calling. There are over 400 approved VAX Service Agents in the UK. For your nearest Service Agent please call VAX Care.