ICP Plumbing Exam. Name: Carefully read each question and then circle the letter of the best answer.
|
|
- Shawn Higgins
- 5 years ago
- Views:
Transcription
1 ICP Plumbing Exam Name: Date: Score: Carefully read each question and then circle the letter of the best answer. 1. A 1 inch diameter faucet, where the inside edge of the spout opening is 2.5 inches away from a single wall is. a. close to the wall b. away from the wall c. exactly where it should be d. too short to be used 2. An 800 gallon water tank shall have a drain pipe at least in diameter. a. 1 inch b. 1-1/2 inches c. 2 inches d. 2-1/2 inches 3. The minimum allowed size of a 1/16" sloped building drain is inches. a. 1-1/4 b. 2 c. 3 d The minimum air gap for a fixture with an effective open of 3/4", located close to a wall is inch(s). a. 1/2 b. 2
2 c. 1-1/2 d. 2-1/2 5. A water closet shall not be set any closer than inches from its center to a wall. a. 12 b. 16 c. 15 d A water heater relief valve shall not. a. discharge on a floor b. discharge into an indirect waste receptor c. have an air cap in the discharge piuping d. have a trap in the discharge piping 7. Bedpan washers and clinical sinks shall connect to the drainage and vent system in accordance with the requirements of a. a. lavatory b. water closet c. bidet d. service sink 8. The diameter of hole bored in joists shall not exceed the depth of the joist. a. 1/3 b. 1/2 c. 1/4 d. 1/8 9. Grab bars with a circular cross section shall have an outside diameter of inch (32 mm) minimum and 2 inches (51 mm) maximum. a. 1 b. 1-1/4
3 c. 1-1/2 d. 1-3/4 10. Sheet copper used for general applications shall not weigh less than. a. six ounces per square foot. b. twelve ounces per square foot c. four pounds per square foot d. four ounces per square foot 11. A drainage stack of two branch intervals receiving the discharge of 30 dfu s, shall be a minimum of inches diameter. a. 2 b. 2.5 c. 3 d A 4 inch copper pipe, passing through a fire-resistance-rated wall may be protected. a. by filling the annular space with concrete b. by an approved firestop system c. by either a or b d. by neither a or b 13. The strainer openings of a shower waste strainer shall be a minimum of inches. a. 1/8 b. 1/4 c. 3/8 d. 1/2 14. CPVC solvent cement shall be in color and conforming to ASTM F 493 when primer is used. a. orange b. red
4 c. purple d. green 15. A circuit vented branch serving four or more water closets and connecting to a drainage stack that receives the discharge from upper horizontal branches shall be provided a vent. a. individual b. relief c. common d. yoke 16. A pipe that is located inside a building and conveys storm water from the roof to the sewer is a? a. Leader b. Conductor c. roof drain d. Storm drain 17. At a velocity of 8 feet per second, a manifold serving a demand of 12 gpm must have a minimum diameter of inches. a. 1/2 b. 3/4 c. 1 d. 1-1/4 18. A pipe that makes an angle of 45 degrees is considered pipe by the code. a. horizontal b. vertical c. obtuse d. angled 19. A yoke vent must be used to vent horizontal offsets of drainage stacks when there are or more branch intervals above the offset. a. 10
5 b. 8 c. 6 d A factory requiring 5 drinking fountains may substitute with bottled water dispensers. a. 1 b. 2 c. 3 d For water service pipe, a standard for galvanized steel pipe is. a. ASTM B43 b. ASTM B 75 c. ASTM A 53 d. ASTM F A factory bathroom with 3 water closets (1.6 gpf), 6 urinals (1gpf), five lavatories and a floor drain has how many drainage fixture units. a. 25 b. 27 c. 30 d Each fixture drain shall connect to the horizontal branch drain being circuit vented. a. horizontally b. vertical to horizontal c. on top of the horizontal drain d. any of the above 24. The minimum capacity of a sewage pump connected to a 2 inch discharge pipe shall be gpm. a. 21
6 b. 30 c. 46 d The minimum air gap for a fixture with an effective open of 1/2", located away from a wall is inch(s). a. 1/2 b. 2 c. 1-1/2 d Building sewers 8 inches and larger must be provided with manholes located not more than feet apart. a. 100 b. 200 c. 75 d According to Table the required flow rate for a bathtub is gpm. a. 4 b. 8 c. 3 d The maximum discharge to a relief vent shall be dfu. a. 2 b. 4 c. 12 d A fixture with a 1-1/4 inch drain has drainage fixture units. a. 2
7 b. 4 c. 1 d A vent terminal shall not be located closer than feet above the top of an openable window. a. 2 b. 4 c. 6 d Hand operated metering faucets shall remain open for seconds minimum. a. 10 b. 15 c. 20 d A 1-1/2 inch "P" trap with slip joints may be used as a cleanout for a maximum inch drain pipe. a b. 1-1/2 c. 2 d. 2-1/2 33. A fixture with a 2 inch drain has drainage fixture units. a. 2 b. 4 c. 3 d Waste stacks serving more than 10 branch intervals must be provided with a relief vent, with which the upper end shall be connected to the vent stack through a wye not less than feet above the floor.
8 a. 1.5 b. 2 c. 3 d Grease interceptors shall conform to any of the following except. a. PDI G101 b. ASME A c. ASME A d. NSF A cast iron mechanical joint coupling for hubless pipe and fittings shall comply with. a. CISP 310 or ASTM C1277 b. ASTM C564 or CAN/CSA B602 c. ASTM C 310 d. ASME A A hose connection vacuum breaker may be used as a backflow preventer for liquids. a. low hazard b. high hazard c. either a or b d. neither a or b 38. Plastic water service pipe shall terminate within feet inside of the point where the pipe penetrates an exterior wall or slab on grade. a. 2 b. 5 c. 8 d PVC primer must be in color. a. red
9 b. green c. purple d. yellow 40. Pipe applied vacuum breakers shall be installed not less than inches above the flood level rim of the fixture served. a. 2 b. 4 c. 6 d Floor drains are not require in. a. commercial kitchens b. public restrooms c. second floor condominiums units d. public coin operated laundries 42. The maximum flow rate for a hand held shower is 80 psi. a. 1.5 b. 2.5 c. 2.2 d Condensate piping of condensing appliances shall maintain a minimum horizontal slope of not less than unit vertical in twelve units horizontal. a. 1/8 b. 1/6 c. 1/4 d. 1/2 44. Shower and tub-shower combination valves and master thermostatic mixing valves shall be equipped with a means to limit the maximum setting of the valve to degrees F. a. 110
10 b. 115 c. 120 d Commercial food grinders shall conform to. a. ASSE 1009 b. ASSE 1008 c. ASTM 502 d. ASTM 502-A 46. A gravity sewer test must maintain 10 foot of head for minutes. a. 10 b. 5 c. 15 d When a bathtub outlet is not used with a shower, the shower waste outlet strainer must have a minimum diameter of inches. a. 1-1/2 b. 2 c. 2-1/2 d The space between the wall and the grab bar shall be inches. a. 1-1/2 b. 1-3/4 c. 2 d. 2-1/4 49. The minimum size fixture water supply pipe for an flush valve urinal is. a. 1/2" b. 3/4"
11 c. 1" d. 1-1/4" 50. Vents exceeding feet shall be increased by one nominal pipe size for the entire developed length of the vent pipe. a. 10 b. 20 c. 30 d A shower compartment with one side 30 inches shall not be less than inches on the adjacent side. a. 24 b. 36 c. 32 d The front of accessible lavatories and sinks shall be inches (865 mm) maximum above the floor, measured to the higher of the rim or counter surface. a. 30 b. 31 c. 32 d According to Table the required water pressure for a temperature controlled shower is psi. a. 25 b. 8 c. 15 d The maximum allowable temperature of wastewater discharged into a sewer is. a. 100
12 b. 120 c. 140 d Solvent cement for PVC plastic pipe shall conform to the following except. a. is permitted to be used both, above and below ground b. must be used with a primer that conforms to ASTM F 656 c. must be applied only to the male portion of the connection d. shall not be purple 56. A clearance in front of accessible bathtubs extending the length of the bathtub and inches (760 mm) minimum in depth shall be provided. a. 56 b. 59 c. 30 d A stack vent handling 125 dfu s with a developed length of 35 feet shall be inches minimum diameter. a. 2 b. 2.5 c. 3 d The water supply connection to a beverage dispenser must be protected by a/an. a. backflow preventer conforming to ASSE 1022 b. an air gap c. either a or b d. beverage dispensers do not require backflow prevention 59. A branch vent, 50 feet in developed length, serving a 3" drain, must be at least inches in diameter. a. 1-1/2
13 b. 2 c. 2-1/2 d Where a vent stack connects to a 4" building drain, the connection shall be located downstream of the drainage stack and within a distance of of the drainage stack. a. 3 feet b. 40 inches c. 4 feet d. 24 inches 61. Plumbing fixtures are. a. required to be third party certified b. required to be third party tested c. not required to be third party certified d. not required to be third party tested 62. A circuit vent shall vent a maximum of traps. a. 2 b. 4 c. 6 d Shower linings shall turn up on all sides at least inches above the finished threshold. a. 1 b. 1.5 c. 2 d The minimum size fixture supply pipe, 40 feet from a 40 psi, for a single shower head is. a. 3/8"
14 b. 1/2" c. 3/4" d. 5/8" 65. The minimum vent size of a sewage pump sump with a pump capacity of 10 gpm is inches. a. 1-1/4 b. 1-1/2 c. 2 d. 2-1/2 66. Solder used on copper shall conform to. a. ASTM F 80 b. ASTM S 75 c. ASTM B 32 d. ASTM M Outdoor enclosures for backflow prevention devices shall comply with. a. ASSE 1056 b. ASSE 1045 c. ASSE 1055 d. ASSE An indirect waste pipe that exceeds feet in total developed length must be trapped. a. 1.5 b. 2 c. 3 d Subsoil drainage components are. a. required to be third party certified b. required to be third party tested c. not required to be third party certified
15 d. not required to be third party tested 70. A 20 ft. length of pipe with slope per foot of 1/4" will produce a drop of inches. a. 3 b. 4 c. 5 d Copper and brass pipe shall not be used if it contains more than an average of grains of hydrogen sulfide per 110 standard cubic feet of gas. a..3 b..03 c. 3 d Except for decorative appliances, an equipment shutoff valve shall be located within feet of the appliance. a. 2 b. 4 c. 6 d Unless otherwise approved, threaded fitting larger than inches shall not be used for gas piping. a. 4 b. 3 c. 5 d Adding height to a vent. a. increases the vent capacity b. decreases the vent capacity c. does not affect the vent capacity
16 d. will cause the appliance to back draft 75. A 1 inch diameter iron gas pipe shall be threaded with approximately threads. a. 8 b. 9 c. 10 d Using CSST, 2 psi natural gas, 1.0 pressure drop,.60 specific gravity, what is the minimum pipe size for a 199,000 gas water heater located 100 away from the meter. a. 13 b. 15 c. 18 d A category I appliance cannot be connected to vent whose effective area is times or greater than the appliance draft hood outlet area. a. 3 b. 5 c. 7 d The maximum design operating pressure for gas piping systems located inside a residence shall nor exceed psi unless the piping system is welded or in a ventilated chase. a. 1/2 b. 2 c. 5 d A 2 inch diameter iron gas pipe shall have approximately inche(s) threaded. a. 3/4 b. 7/8 c. 1
17 d. 1-1/2 80. The slope of a vent connector shall be upward at least inch per foot. a. 1/16 b. 1/8 c. 1/4 d. 1/2 81. The minimum test pressure for a specific gas piping system is times the working pressure a. 1-1/2 b. 2 c. 2-1/2 d A 3/4 steel gas pipe shall be supported at intervals not exceeding feet. a. 4 b. 5 c. 6 d /2 gas tubing shall be supported at intervals not exceeding feet. a. 4 b. 5 c. 6 d Screens over combustion air openings shall have a mesh size not less than inch. a. 1/8 b. 1/16 c. 1/4 d. 1/2
18 85. A btu equals the amount of heat required to raise the temperature of one lb. of water one degree F, therefore btu s are required to raise 10 lbs. water 60 degrees F. a. 60 b. 6 c. 600 d An employee must complete a form to claim federal income tax withholding allowances. a. 941 b c. I-9 d. W A water heater costs $400, tax is 8%, labor is $180 and overhead is 15%. What is the sales price needed to make 30% profit? a. $1113 b. $887 c. $841 d. $ The minimum age for hazardous occupations is. a. 16 b. 17 c. 18 d Which of the following is not a current asset? a. prepaid insurance b. cash c. building d. accounts receivable
19 90. An employee works 46 hours for the week, his straight time pay is $12.50/hour. What is his gross pay? a. $ b. $ c. $ d. $ The employee must pay 6.2% Social Security Tax, therefore the amount of SS tax withheld on a gross pay of $ would be $ a. $41.66 b. $4.17 c. $ d. $ Employers are required by law to. a. pay overtime for time worked over 40 hour per week b. provide lunch breaks c. limit the number of hours worked d. provide rest periods 93. How much is saved when a 1.5% discount is taken on a $23,678 invoice? a. $3.55 b. $35.17 c. $ d. $ If the yearly fuel cost to operate a water heater with an overall efficiency of 60% is $500 what would the savings be using an 80% efficient water heater? a. $125 b. $100 c. $80 d. $75
20 95. protects your business against loss due to fire, theft or weather related incidents. a. Property insurance b. Comprehensive insurance c. Life insurance d. vehicle insurance 96. Disabilities covered by the Americans with Disabilities Act include all the disabilities below except. a. hearing b. seeing c. breathing d. broken bones 97. A company has annual sales of $850,000 with $230,000 overhead. What is the percent overhead? a. 27% b. 32% c. 37% d. 18% 98. In order to cover employee bonuses totaling $45,000, how much more revenue is needed if your company is earning an average 20% gross profit? a. $90,000 b. $ c. $ d. $225, A water heater costs $475, tax is 8%, labor is $180 and overhead is 15%. What is the sales price needed to make 30% profit? a. $1113 b. $1260 c. $841 d. $796
21 100. A federal ID number (EIN) is required by al businesses except. a. a sole proprietor ship with no employees b. a partnership with no employees c. an S corporation d. a corporation with no employees
22 Answer Sheet 1. a. Table footnote a 2. b. Table d. Table 710.1(10 4. d. Table c d b a b ICC/ANSI 10. b c. Table 710.1(2) 12. c , exception 1 and b a b b. 202 definition of conductor 17. c. Table b. def horizontal pipe "less than" 19. d b c. Table d. Table a a. Table d. Table d a. Table b c. Table a
23 31. a ICC/ANSI 32. c exception c. Table c d a c. Table b c c c b. Table see footnote a 43. a c a c d a ICC/ANSI 49. b. Table d d d ICC/ANSI 53. d. Table c c c ICC/ANSI 57. b. Table c b. Add 1/2 pipe size when over 40 feet 60. b b. Table 303.4
24 62. d. 202 definition of circuit vent 63. c a. Table footnote a 65. a. Table c c d b. Table c. 71. a c a a. study vent Tables 75. c. Table b. Table 402.4(17) 77. c c. 79. c. Table c a d. Table a. Table c c. 86. d. 87. a. Profit and overhead are expressed as percentages of cost (15%+30%= 45%, Total cost = $612, sales price = total cost/(100%-% needed to cover profit and overhead) 88. c. 89. c. 90. b. 91. a
25 92. a. 93. c. 94. a. (60/80) x 500 = 375, = a. 96. d. 97. a /850000= d. 45,000/.20=225, a. Profit and overhead are expressed as percentages of cost (15%+30%= 45%, Total cost = $693, sales price = total cost/(100%- Minus % needed to cover profit and overhead),693/.55= a
IPC Plumbing Exam. Name: Carefully read each question and then circle the letter of the best answer.
IPC Plumbing Exam Name: Date: Score: Carefully read each question and then circle the letter of the best answer. 1. A vent stack handling 25 dfu s with a developed length of 35 feet shall be inches minimum
More informationIPC Plumbing Exam. Name: Carefully read each question and then circle the letter of the best answer.
IPC Plumbing Exam Name: Date: Score: Carefully read each question and then circle the letter of the best answer. 1. The minimum air gap for a fixture with an effective open of 1/2", located away from a
More informationLevel I Chapter 1 Worksheet
Chapter 1 Worksheet 1. For applicability requirements of the Plumbing Code, refer to: a. Building Code b. Administration and Enforcement Code c. Plumbing Code d. Residential Code 2. The provisions of the
More informationRead Only Document Not For Distribution
Chapter 5 Traps, Cleanouts and Backwater Valves 5.1 SEPARATE TRAPS FOR EACH FIXTURE a. Plumbing fixtures shall be separately trapped by a water seal trap placed as close as possible to the fixture outlet.
More informationSTACKS AND STACK VENTS
CHAPTER 9 VENTS SECTION 901 GENERAL 901.1 Scope. The provisions of this chapter shall govern the materials, design, construction and installation of vent systems. 901.2 Trap seal protection. The plumbing
More informationSanitary Drainage Systems
11.1 MATERIALS See Section 3.1. Sanitary Drainage Systems 11.2 BUILDING SEWERS AND BUILDING DRAINS 11.2.1 Sewer or Drain in Filled Ground Chapter 11 Building sewers or building drains that are installed
More informationPLUMBING REQUIREMENTS
PLUMBING REQUIREMENTS This handout is a compilation of the standard requirements based on the State Plumbing Code and City Ordinance for projects of this type. This information sheet does not contain all
More informationSummary of BBS Proposed Ohio Plumbing Code Rule Changes October 2016
Summary of BBS Proposed Ohio Plumbing Code Rule Changes October 2016 Ohio Administrative Code Rule Number OPC Section IPC origin Reason for proposed 4101:3-2-01 Alternate on-site 2015 Added definition
More informationCHAPTER 31. VENTS Reserved 2003 INTERNATIONAL RESIDENTIAL CODE 425R
CHAPTER 31 VENTS Reserved 2003 INTERNATIONAL RESIDENTIAL CODE 425R This page left intentionally blank. 426R 2003 INTERNATIONAL RESIDENTIAL CODE For SI: PIPE SIZE (inches) TABLE P3107.3 COMMON VENT SIZES
More information2016 Plumbing Supplemental Plan Review List
Building Division 555 Santa Clara Street Vallejo CA 94590 707.648.4374 2016 Plumbing Supplemental Plan Review List POTABLE WATER SYSTEM P1. Specify which fixtures are for private use and which are for
More informationCHAPTER 9 VENTS SECTION
CHAPTER 9 VENTS SECTION 901 GENERAL 901.1 Scope. The provisions of this chapter shall govern the materials, design, construction and installation of vent systems. 901.2 Trap seal protection. The plumbing
More informationMATERIALS Traps TRAPS. No. IPC IRC Description
MATERIALS Traps TRAPS MAX " MAX 0" No. IPC IRC Description 00. P0.6 00. P0.6 00. P0. 00. () P0.6 Exc. Vertical distance from fixture to the trap weir can not exceed ". Horizontal distance from the fixture
More information1 Exam Prep Plumbing State Contractors Practice Exam 2
1 Exam Prep Plumbing State Contractors Practice Exam 2 1 According to Chapter 64E-6, when sizing a grease interceptor used in a restaurant, the correct formula is. A. (S) x (EW 12) x (LF) B. (S) x (GS)
More informationPLUMBING FIXTURES Reserved
CHAPTER 27 PLUMBING FIXTURES Reserved 2003 INTERNATIONAL RESIDENTIAL CODE 395R This page left intentionally blank. 396R 2003 INTERNATIONAL RESIDENTIAL CODE SECTION P2708 SHOWERS P2708.1 General. Shower
More informationSCHOOL DISTRICT PALM BEACH COUNTY BUILDING DEPARTMENT PLAN REVIEW CHECK LIST -- PLUMBING
SCHOOL DISTRICT PALM BEACH COUNTY BUILDING DEPARTMENT PLAN REVIEW CHECK LIST -- PLUMBING 3300 SUMMIT BOULEVARD WEST PALM BEACH, FLORIDA 33406 TEL (561) 688-7687 FAX (561) 688-7654 http://www.palmbeach.k12.fl.us/fm/bd/index.htm
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 22 40 00 - PLUMBING FIXTURES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Faucets for lavatories, bathtubs, bathtub/showers, showers and sinks. 2. Flushometers. 3. Toilet
More informationCHAPTER 9 VENTS. run undiminished in size and as directly as possible from the building drain through to the open air above the roof.
CHAPTER 9 VENTS SECTION 90 GENERAL run undiminished in size and as directly as possible from the building drain through to the open air above the roof. 90. Scope. The provisions of this chapter shall govern
More informationMatrix of changes for the National Standard Plumbing Code July 2013
Matrix of changes for the National Standard Plumbing Code July 2013 Item # Section Number Person Submitting Change Committee Action 10-77 10.20.8 and Table 3.1.3 XI Certification 10-82 12.16 Size and Lengths
More informationA GUIDE TO PASSING THE PLUMBING EXAM
A GUIDE TO PASSING THE PLUMBING EXAM BASED ON THE INTERNATIONAL PLUMBING AND FUEL GAS CODES WRITTEN BY JOHN WHITE REVISED 2014 2007-2014 This manual is the sole property of Energy Marketing Services. No
More information1 Exam Prep Plumber s Handbook Tabs and Highlights
1 Exam Prep Plumber s Handbook Tabs and Highlights These 1 Exam Prep Tabs are based on the Plumber s Handbook Revised 2006. Each Tabs sheet has five rows of tabs. Start with the first tab at the first
More informationPLUMBING FIXTURES CHAPTER 27
CHAPTER 27 PLUMBING FIXTURES SECTION P2701 FIXTURES, FAUCETS AND FIXTURE FITTINGS P2701.1 Quality of fixtures. Plumbing fixtures, faucets and fixture fittings shall be constructed of approved materials,
More informationRead Only Document Not For Distribution
Chapter 9 Indirect Waste Piping and Special Wastes 9.1 INDIRECT WASTES 9.1.1 General Drains from fixtures, fixture compartments, equipment, appliances, appurtenances, and other devices requiring protection
More informationENERGY MARKETING SERVICES
1 IMPORTANT STUFF This manual has been designed as a supplemental aid for students preparing to take the Plumbing Exam based on the international codes. It is not intended to replace any manuals or material
More informationCHAPTER 10 TRAPS AND INTERCEPTORS
CHAPTER 10 TRAPS AND INTERCEPTORS 1001.0 Traps Required. 1001.1 Each plumbing fixture, excepting those having integral traps or as permitted in Section 1001.2, shall be separately trapped by an approved
More informationSpecial Requirements For Health Care Facilities
Chapter 14 Special Requirements For Health Care Facilities 14.1 GENERAL This Chapter applies to special fixtures and systems that occur in health care facilities and to the special plumbing requirements
More informationAPPENDIX J ILLUSTRATIONS
The following figures have been included in the 1994 edition of the Standard Plumbing Code to aid in interpreting this code. The figures are not to be construed as superseding the written text, but merely
More informationTABLE OF CONTENTS Limitations of Authority...6 Table Plumbing Permit Fees...7
TABLE OF CONTENTS CHAPTER 1 ADMINISTRATION.............1 101.0 General.......................1 101.1 Title..........................1 101.2 Scope........................1 101.3 Purpose......................1
More informationTABLE OF CONTENTS. CHAPTER 2 DEFINITIONS General Applicability Definition of Terms General...
TABLE OF CONTENTS CHAPTER 1 ADMINISTRATION..............1 101.0 General.......................1 101.1 Title..........................1 101.2 Scope........................1 101.3 Purpose......................1
More informationCHAPTER 10 TRAPS AND INTERCEPTORS TABLE 10-1 HORIZONTAL LENGTHS OF TRAP ARMS (EXCEPT FOR WATER CLOSETS AND SIMILAR FIXTURES) 1, 2
CHAPTER 10 TRAPS AND INTERCEPTORS < 1001.0 Traps Required. Each plumbing fixture, excepting those having integral traps or as permitted in Section 1001.1, shall be separately trapped by an approved type
More informationGARCIA GALUSKA DESOUSA Consulting Engineers
L#58619/Page 1/November 1, 2017 PLUMBING Executive Summary: Presently, the Plumbing Systems serving the building are cold water, hot water, sanitary, waste and vent system, storm drain piping, and natural
More information2015 UPC Chapter 8 Indirect Wastes RV
PLEASE DO NOT BOOKMARK ANY ANYTIMECE WEBPAGES! Our system will remember the last page you viewed when logging out and back in but please DO NOT exit out when taking a test. Your place will NOT be saved.
More informationPro Vent TM. Provent Systems Inc Capital Circle Lawrenceville Georgia
Pro Vent TM Guide to Design and Usage Provent Single System Handling Installation Corrosion Ease Simplicity Resistance IPMO Copyright (c) 2014, Pro Vent Systems Inc., plus *2016 Revisions ll Rights Reserved
More informationRead Only Document Not For Distribution
Chapter 14 Special Requirements For Health Care Facilities 14.1 GENERAL This Chapter applies to special fixtures and systems that occur in health care facilities and to the special plumbing requirements
More informationBuilding Utilities 1 Plumbing and Sanitary Systems
Building Utilities 1 Plumbing and Sanitary Systems Taken from UST Architecture exams by Arch. Rafael Alli Recommended review material for UST Preboard Exam Prepared by: arkireviewph.multiply.com Types
More informationAPPENDIX L ALTERNATE PLUMBING SYSTEMS
ALTERNATE PLUMBING SYSTEMS L 1.0 General. L 1.1 Applicability. The intent of this appendix is to provide clarification of procedures for the design and approval of engineered plumbing systems, alternate
More informationTABLE OF CONTENTS. CHAPTER 2 DEFINITIONS General Applicability Definition of Terms General...
TABLE OF CONTENTS CHAPTER 1 ADMINISTRATION................1 101.0 Title, Scope, and General...........1 101.1 Title............................1 101.2 Purpose.........................1 101.3 Plans Required...................1
More informationPERFORMANCE TECHNICAL SPECIFICATION *************************************************************************** SECTION D20 PLUMBING 02/18
NAVFAC PTS-D20 (February 2018) ------------------------------ Preparing Activity: NAVFAC SUPERSEDING PTS-D20 (September 2016) PERFORMANCE TECHNICAL SPECIFICATION SECTION D20 PLUMBING 02/18 NOTE: This section
More informationTABLE OF CONTENTS Limitations of Authority...6 Table Swimming Pool, Spa, and Hot Tub Permit Fees...7
TABLE OF CONTENTS CHAPTER 1 ADMINISTRATION..............1 101.0 General.......................1 101.1 Title..........................1 101.2 Scope........................1 101.3 Purpose......................1
More informationplumbing for greywater
plumbing for greywater october 2015 christina bertea ~union trained journeywoman plumber (1978) ~plumbing contractor (1996) ~greywater action singingwater@jps.net plumbing for greywater basic parts of
More informationCHAPTER VI BUILDING PLUMBING
CHAPTER VI BUILDING PLUMBING 6.1. INTRODUCTION The chapter covers questions related to water demand, distribution and drainage. The basic principles for planning and installing common plumbing systems
More informationPLAN REVIEW SUBMITTAL GUIDE
PLAN REVIEW SUBMITTAL GUIDE Plans, specifications and other construction documentation for the initial plan review should be as complete as possible at the time of submittal. Use this convenient guide
More informationCUSTOMIZED TEACHER ASSESSMENT BLUEPRINT PLUMBING. Test Code: 5924 Version: 01
CUSTOMIZED TEACHER ASSESSMENT BLUEPRINT PLUMBING Test Code: 5924 Version: 01 Specific competencies and skills tested in this assessment: Safety Follow rules for fire safety Follow rules for housekeeping
More information2015 UPC CODE - CHAPTER 8 INDIRECT WASTES
801.0 General. 2015 UPC CODE - CHAPTER 8 INDIRECT WASTES 801.1 Applicability. This chapter shall govern the materials, design, and installation of indirect waste piping, receptors, and connections; and
More informationSECTION PLUMBING
SECTION 22 10 00 PLUMBING PART 1 GENERAL 1.1 WORK INCLUDED A. Furnish all labor, material and equipment necessary for the complete installation of the sanitary sewer system (including soil and vent piping),
More informationTRUMAN STATE UNIVERSITY PRESIDENT S RESIDENCE RENOVATION
SECTION 224100 - RESIDENTIAL PLUMBING FIXTURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationWATER HAMMER ARRESTORS & MISC. SPECIALTIES
TABLE OF CONTENTS Pictorial Index Water Hammer Arrestors Certification Sizing & Placement Backwater Valves Typical Installations Trap Seal Primers Compliance Pressure & Flow Characteristics Typical Installations
More informationDOMESTIC WATER PACKAGED BOOSTER PUMPS
DIVISION 22 PLUMBING 22 11 16 DOMESTIC WATER PIPING 22 11 19 DOMESTIC WATER PIPING SPECIALTIES 1. To facilitate landscape and other maintenance operations, exterior hose bibs shall be provided at 150 foot
More informationCHAPTER 10 TRAPS AND INTERCEPTORS The vent pipe opening from a soil or waste No more than one (1) approved slip joint
CHAPTER 10 TRAPS AND INTERCEPTORS 1001.0 Traps Required. 1001.1 Each plumbing fixture, excepting those having integral traps or as permitted in Section 1001.2, shall be separately trapped by an approved
More informationTest Code: 8117 / Version 1
Pennsylvania Customized Assessment Blueprint Plumbing Technology/Plumber PA Test Code: 8117 / Version 1 Copyright 2012. All Rights Reserved. General Assessment Information Plumbing Technology/Plumber PA
More informationDenotes a new question! Denotes a revised/revisited question. September 2009 General:
General: 1) (Q) What does a contractor/permit holder have to supply for an inspection? (A) Section 107.2 of the NC Administrative Code states that it is the duty of the permit holder to provide access
More informationFIXTURES, FAUCETS AND FIXTURE FITTINGS
CHAPTER 4 FIXTURES, FAUCETS AND FIXTURE FITTINGS SECTION 401 GENERAL 401.1 Scope. This chapter shall govern the materials, design and installation of plumbing fixtures, faucets and fixture fittings in
More informationPlumbing Guidelines 2012 IBC/ANSI A
Plumbing Guidelines 2012 IBC/ANSI A117.1-2009 This document provides basic and fundamental information for accessible plumbing fixtures, toilet rooms and bathing facilities. It is not intended to replace
More informationPLUMBING INSTALLATIONS
PLANNING, PROPERTY AND DEVELOPMENT DEPARTMENT PLUMBING INSTALLATIONS A homeowner guide to plumbing requirements for single-family dwellings November 2017 contents Permit Requirements... 3 Inspection Requirements...
More information2016 CALIFORNIA CODES KITCHEN, BATH & LAUNDRY REMODEL REQUIREMENTS
City of Redwood City Community Development Department Building and Inspection Department 1017 Middlefield Road Redwood City, CA 94063 Phone (650) 780-7350 2016 CALIFORNIA CODES KITCHEN, BATH & LAUNDRY
More informationMechanical Inspection Plumbing
0811 Fixtures Sinks, drinking fountains, water closets, showers, etc. Classroom Sinks. Classroom sinks (19) are enameled cast iron self rimming side ledge with gooseneck faucet trim with index handles,
More informationCHaPTeR 10. TRaPS and INTeRCePTORS. Table 10-1 Horizontal lengths of Trap arms (except for water closets and similar fixtures)*
CHaPTeR 10 TRaPS and INTeRCePTORS 1001.0 Traps Required. 1001.1 Each plumbing fixture, excepting those having integral traps or as permitted in Section 1001.2, shall be separately trapped by an approved
More information2012 Virginia Plumbing Code & VRC (Plumbing) Update Training
2012 Virginia Plumbing Code & VRC (Plumbing) Update Training ----------------------------- Henrico County Department of Building Construction and Inspections Introduction This presentation was prepared
More informationCONTINUING EDUCATION UPC Definitions Code Course. 4 hours Course # ID09143 (CODE) PO Box Spokane, WA
AMERICAN PLUMBING INSTITUTE 2015 33 CONTINUING EDUCATION PO Box 31131 Spokane, WA 99223-3018 www.apiceu.com 2009 UPC Definitions Code Course 4 hours Course # ID09143 (CODE) DISCLAIMER NOTE: This course
More informationSummary of Substantive Changes between the 2012 and 2018 editions of ASME A /CSA B125.1 Plumbing Supply Fittings
Summary of Substantive Changes between the 2012 and 2018 editions of ASME A112.18.1/CSA B125.1 Plumbing Supply Fittings Presented to the IAPMO Standards Review Committee on May 6, 2013 General: The changes
More informationDEFINITIONS CHAPTER 2
CHAPTER 2 DEFINITIONS SECTION 201 GENERAL 201.1 Scope. Unless otherwise expressly stated, the following words and terms shall, for the purposes of this code, have the meanings shown in this chapter. 201.2
More informationC. ASSE 1013: Performance Requirements for Reduced Pressure Principle Backflow Preventers.
SECTION 22 10 00 PLUMBING PIPING AND PUMPS PART 1 - GENERAL 1.1 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design.
More informationRead Only Copy Not For Distribution. Chapter 10. Water Supply and Distribution 10.1 QUALITY OF WATER SUPPLY 10.2 RESERVED 10.
Water Supply and Distribution 10.1 QUALITY OF WATER SUPPLY a. Only potable water shall be supplied to plumbing fixtures used for drinking, bathing, culinary use or the processing of food, medical or pharmaceutical
More informationINSPECTION OF COMMERCIAL KITCHEN PLUMBING
INSPECTION OF COMMERCIAL KITCHEN PLUMBING 801.1 SCOPE Food-handling establishments 2 - by John Williams, Jr. Plumbing Control Supervisor Onondaga County Water Environment Protection Commercial Kitchens
More informationDEFINITIONS CHAPTER 2
CHAPTER 2 DEFINITIONS SECTION PC 201 GENERAL 201.1 Scope. Unless otherwise expressly stated, the following words and terms shall, for the purposes of this code, have the meanings shown in this chapter.
More informationPERFORMANCE TECHNICAL SPECIFICATION *************************************************************************** SECTION D20 PLUMBING 02/18
NAVFAC PTS-D20 (February 2018) ------------------------------ Preparing Activity: NAVFAC SUPERSEDING PTS-D20 (September 2016) PERFORMANCE TECHNICAL SPECIFICATION SECTION D20 PLUMBING 02/18 NOTE: This section
More informationPlumbing Guidelines 2015 Minnesota Accessibility Code Based on the 2012 IBC and 2009 ANSI A117.1
Plumbing Guidelines 2015 Minnesota Accessibility Code Based on the 2012 IBC and 2009 ANSI A117.1 This document provides basic and fundamental information for accessible plumbing fixtures, toilet rooms
More informationDESIGN AND CONSTRUCTION STANDARDS GENERAL DESIGN GUIDELINES
2.05 PLUMBING GENERAL DESIGN AND CONSTRUCTION STANDARDS GENERAL DESIGN GUIDELINES - 2.05 It is expected that the plumbing design professional will conform to accepted good engineering design practices.
More informationAPPENDIX A. A 3.2 Determine the elevation of the highest. A 3.3 Subtract the sum of loss in static pressure
APPENDIX A RECOMMENDED RULES FOR SIZING THE WATER SUPPLY SYSTEM Because of the variable conditions encountered, it is impractical to lay down definite detailed rules of procedure for determining the sizes
More informationSECTION PLUMBING FIXTURES
CSUEB Pioneer Heights Phase r 15410 Page 1 SECTION 15410 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationDUKE UNIVERSITY CONSTRUCTION STANDARDS
1 22 40 00 Plumbing Fixtures 1. General A. Definitions 1. Section includes a. Water closets and urinals b. Lavatories, sinks, and service sinks c. Electric water coolers, drinking fountains, d. Showers
More informationDrain and Vent Systems 6 CE Hours
Drain and Vent Systems 6 CE Hours Wisconsin Contractors Institute N27 W23953 Paul Road, Suite 203 Pewaukee, WI 53072 www.wicontractorsinstitute.com 262-409-4282 What is the purpose of this course? The
More informationMethods of Venting Plumbing Fixtures and Traps in the 2018 IPC
People Helping People Build a Safer World Methods of Venting Plumbing Fixtures and Traps in the 2018 IPC Installation, Flexibility and Opportunity for Savings Lee Clifton, Senior Director of PMG Resources,
More informationDEFINITIONS CHAPTER 2
CHAPTER 2 DEFINITIONS SECTION 201 GENERAL 201.1 Scope. Unless otherwise expressly stated, the following words and terms shall, for the purposes of this code, have the meanings shown in this chapter. 201.2
More informationCHAPTER 8 CHIMNEYS AND VENTS
CHAPTER 8 CHIMNEYS AND VENTS SECTION 801 GENERAL 801.1 Scope. This chapter shall govern the installation, maintenance, repair and approval of factory-built chimneys, chimney liners, vents and connectors.
More informationPipe Sizing Table. Hydraulic Load Served (fixture units)
MODULE 1 INTRODUCTION Notes: A Pipe Type Horizontal branch Pipe Sizing Table Hydraulic Load Served (fixture units) Size (in.) Code Reference 2 + 1.5 = 3.5 2 7.4.9.1.(1) B Soil stack 13.5 + 13.5 = 27 3
More informationTABLE OF CONTENTS. Part I Administrative... 1
Part I Administrative............................ 1 CHAPTER 1 ADMINISTRATION............... 1 R101 Title, Scope and Purpose.................... 1 R102 Applicability.............................. 1 R103
More informationCALIFORNIA PLUMBING CODE MATRIX ADOPTION TABLE APPENDIX A - RECOMMENDED RULES FOR SIZING THE WATER SUPPLY SYSTEM 1 2 1/AC AC SS SS/CC
CALIFORNIA PLUMBING CODE MATRIX ADOPTION TABLE APPENDIX A - RECOMMENDED RULES FOR SIZING THE WATER SUPPLY SYSTEM Adopting Agency BSC SFM HCD DSA OSHPD CSA DPH AGR DWR CA 1 2 1/AC AC SS SS/CC 1 2 3 4 Adopt
More informationPlumbing. Definitions. Background Factors. Air Chambers. Air Gap (Drainage System) Air Gap (Water Distribution System) Air Lock.
Plumbing Plumbing may be defined as practice, materials, and fixtures used in the installation, maintenance, and alteration of all piping, fixtures, appliances, and appurtenances in connection with sanitary
More informationLand Use and Environmental Service Agency (Code Enforcement) Plumbing 2010
General: 1) (Q) Who enforces the cutting and notching requirements found in the plumbing code? (A) The plumbing inspector would question the contractor initially. A building inspector would either take
More informationC O D E S & A M M E N D M E N T S
SEVIER COUNTY UTILITY DISTRICT SEPTEMBER 2, 2014 Sevier County Utility District has adopted the 2009 International Fuel Gas Code for gas inspections. The following pages contain frequently used codes and
More informationPlumbing Technology/Plumber CIP Task Grid
1 Secondary Task List 100 DEMONSTRATE PERSONAL SAFETY IN THE TRAINING LABORATORY 101 Follow rules for fire safety. 102 Follow rules for housekeeping safety. 103 Follow shop rules. 104 Follow rules for
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 22 PLUMBING. A. This Section includes the following sanitary drainage piping specialties:
SECTION 221319 - SANITARY WASTE PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following sanitary drainage piping specialties: 1. Backwater valves. 2. Cleanouts. 3. Floor
More informationA. Section Joint Sealants: Seal fixtures to walls and floors.
SECTION 224000 - PLUMBING FIXTURES PART 1 GENERAL 1.1 SECTION INCLUDES A. Water closets. B. Urinals. C. Lavatories. D. Sinks. E. Service sinks. F. Showers. G. Wash fountains. H. Eye wash fountains. 1.2
More informationA. This Section includes the following domestic water piping specialties:
SECTION 221119 DOMESTIC WATER PIPING SPECIALTIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More information2009 IPC ,IMC Q &A ANDIFGC
2009 IPC,IMC ANDIFGC Q &A TABLE OF CONTENTS PREFACE.... ix ABOUT THE INTERNATIONAL CODE COUNCIL...x IPC CHAPTER 1 SCOPE AND ADMINISTRATION...1 Section 101 General... 1 Section 102 Applicability... 1 Section
More informationDefinitions UPC Code - Chapter 2 Definitions A-I
2015 UPC Code - Chapter 2 Definitions A-I Definitions 201.1 Applicability. For the purpose of this code, the following terms have the meanings indicated in this chapter. 202.0 Definition of Terms. 202.1
More informationB. Shop Drawings: Include diagrams for power, signal, and control wiring.
SECTION224213.13 -COMMERCIAL WATERCLOSETS PART 1- GENERAL 1.1 SUMMARY Section Includes: 1. Water closets. 2. Flushometer valves. 3. Toilet seats. 1.2 ACTION SUBMITTALS Product Data: For each type of product.
More informationPerkins Statewide Articulation Agreement. Documentation item: Secondary Competency Task List Coversheet
Perkins Statewide Articulation Agreement Documentation item: Secondary Task List Coversheet The Secondary School agrees to: A. Implement the approved PDE Program(s) of Study. B. Provide assessment of student
More informationGIANT. Little. Guidelines for Sizing. Pump Company. Sewage Pumps & Systems. Sewage Pumps & Systems
Sewage Pumps & Systems GIANT Little Pump Company Guidelines for Sizing Sewage Pumps & Systems These guidelines cover the steps that need to be taken to accurately select the correct sewage pump and applicable
More informationCHAPTER 10 TRAPS AND INTERCEPTORS
CAPTER 10 TRAPS AND INTERCEPTORS 1001.0 Traps Required. 1001.1 Each plumbing fixture, excepting those having integral traps or as permitted in Section 1001.2, shall be separately trapped by an approved
More information1. You are required to use a 20 foot ladder placed up against a building that is 40 high. At what
This practice exam will require you to have a calculator, pencil, scrap paper, a copy of the 2005 National Plumbing Code and will contain many similar questions as the current Plumbing Red Seal trade certification.
More information2012 INTERNATIONAL FUEL GAS CODE VENTS
2012 INTERNATIONAL FUEL GAS CODE SECTION 502 (IFGC) VENTS 502.1 General. All vents, except as provided in Section 503.7, shall be listed and labeled. Type B and BW vents shall be tested in accordance with
More informationc. Direct or indirect?
~ \ 1.) GENERAL a. Definitions: Chapter B Code References (1) Air-break Comm 81.01 (5) (2) Air-gap, drain system Comm 81.01 (6) (3) Flood level rim Comm 81.01(102) (4) sink Comm 81.01(105) (5) Indirect
More information2015 MPC, MMC and IFGC Significant Changes
2015 MPC, MMC and IFGC Significant Changes Based on the 2015 Michigan Plumbing Code, (MPC), the 2015 Michigan Mechanical Code (MMC) and the 2015 International Fuel GaS Code (IFGC) Purpose This program
More informationPLUMBING CURRICULA OUTLINE
PLUMBING CURRICULA OUTLINE CORE CURRICULUM 2015 Basic Safety (Construction Site Safety Orientation) (12.5 Hours) (Module ID 00101-15) Presents basic jobsite safety information to prepare workers for the
More informationASME STANDARDS IN MODEL CODES
STANDARDS IN MODEL CODES ASME Name Model Code With Year of Referenced IPC IRC UPC 2009 NSPC A112.1.2 Air Gaps in Plumbing 2004 2004 2004 2004 A112.1.3 Air Gap Fittings For Use With Plumbing, Appliances
More informationCHAPTER 4 FIXTURES WHAT FIXTURES ARE REQUIRED? SINGLE-FAMILY RESIDENCE
PlumbingCode06_ch04 5/29/06 8:11 AM Page 1 CHAPTER 4 FIXTURES There is much more to fixtures than meets the eye. Fixtures are a part of the final phase of plumbing. When you are planning a plumbing system,
More informationWastewater. Guidelines for Sizing mscdirect.com. Call MSC today to learn about the latest LittleGiant products.
Wastewater Guidelines for Sizing Features These guidelines cover the steps which need to be taken to accurately select the correct sewage pump and applicable systems to use in sewage ejectors. Work through
More informationStructural Guidelines. Food Service Establishments. Retail Food Stores
Structural Guidelines for Food Service Establishments and Retail Food Stores Jefferson County Department of Health Food & Lodging Protection Division 1 Before construction or remodeling of a food service
More informationPERFORMANCE TECHNICAL SPECIFICATION *************************************************************************** SECTION D20 PLUMBING 02/18
NAVFAC PTS-D20 (February 2018) ------------------------------ Preparing Activity: NAVFAC SUPERSEDING PTS-D20 (September 2016) PERFORMANCE TECHNICAL SPECIFICATION SECTION D20 PLUMBING 02/18 NOTE: This section
More information