W-750-IS Specifications
|
|
- Domenic Davis
- 5 years ago
- Views:
Transcription
1 Big Dipper IS Central Automatic W-750-IS Specifications MOTOR/TIMER ENCLOSURE 1 CLEARANCE FROM TOP OF TANK REQUIRED FOR STRAINER BASKET & LID REMOVAL EMPTY INTO COOKING OIL RECYCLING CONTAINER DAILY GC-7 GREASE COLLECTOR 8 QUART CAPACITY PIPE / 17.5 END VIEW FEATURES: 42. SIDE VIEW 45. Fully automatic self cleaning cycle. Removes collected grease & oils from tank without any operator assistance. Comes complete with 24- hour timer. Constructed of corrosion resistant materials suitable for installation in virtually any location. Attractive sanitary Stainless Steel exterior Integrated Motor/Grease Outlet/Heater/Lid enables a fast, do-it-yourself unit operation reversal. TOP VIEW Easy lift grease collector simplifies grease collection container emptying. Compact footprint. TECHNICAL DATA Materials: Exterior: 304 Stainless Steel, Bright Finish Interior: Rotationally Molded Polyethylene Electrical: 115 VAC, 60 Hz, 520 Watts (4.5 Amps) Maximum Inlet Flow Rate: 75 GPM Number of Skimming Wheels: 1 Skimming Rate: 20 Pounds Per Hour Grease Retention Capacity: 150+ Pounds Internal Solids Strainer Capacity: 3.70 Gallons 1/ Greensboro St. Asheboro, N. C Phone (336) North America: (800)
2 Big Dipper IS Central Automatic W-750-IS Specifications INSTALLATION INFORMATION Suggested Minimum Footprint Dimensions DO... Allow a minimum of 1 clearance from top of tank for removal of unit lid. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown GC-7 GREASE COLLECTOR Make sure the height above the Internal Strainer Access Cover is enough to remove the strainer. Make piping connections with rubber No Hub connectors. Keep outlet piping as straight as possible. Use only sweep connections. Install vent on outlet piping. Fill the tank with water before energizing the power to the motor and heater. Set Programmable Time Controller for proper operating times. DONʼT... Install P trap on outlet connection of tank. (Note: the unit already has an internal gas trap). Reduce pipe size on outlet piping. Note: Installations must comply with all applicable local, state, and national codes for your area. Job Specification: Grease and oils separator(s) shall be Thermaco Big Dipper automatic grease/oil recovery system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install Thermaco Big Dipper Model No. W-750-IS, bright finish type 304 stainless steel exterior, rotationally molded polyethylene interior automatic self-cleaning grease and oil recovery separator(s) for floor mounted or partially recessed installation, rated at 75 gallons per minute peak flow, 150 pounds of grease capacity and including as an integral part of the unit, 1 rotating gear hydrophobic wheel assembly for automatic grease/oil removal, an integral flow control device, self-regulating enclosed electric immersion heater, a vessel vent, an integral gas trap, an integral programmable 24-hour multi-event time control, a field reversible motor location, a field reversible grease/oil sump outlet, quick release stainless steel lid clamps, a gasketted and fully removable 304 stainless steel lid, lift-out strainer basket access, an internal stainless steel strainer basket for collection of coarse solids, and a separate grease and oils collection container. Electric assembly shall be tested to comply with pertinent sections of the Standards for Safety ANSI/UL 73 and/or ANSI/UL Electric motor shall be equipped with thermal overload protection with automatically resettable switch Greensboro St. Asheboro, N. C Phone (336) North America: (800) /06
3 MOTOR/TIMER ENCLOSURE 24.5 Big Dipper IS Central Automatic W-1250-IS Specifications 1 CLEARANCE FROM TOP OF TANK REQUIRED FOR STRAINER BASKET & LID REMOVAL PIPE / DUAL GC-6 GREASE 16.5 COLLECTORS QUART CAPACITY END VIEW FEATURES: SIDE VIEW 55. Fully automatic self cleaning cycle. Removes collected grease & oils from tank without any operator assistance. Comes complete with two 24-hour timers. Constructed of corrosion resistant materials suitable for installation in virtually any location. Attractive sanitary Stainless Steel exterior Integrated Motor/Grease Outlet/Heater/Lids enables fast, do-it-yourself unit operation reversal. TOP VIEW Easy lift grease collectors simplify grease collection container emptying. Compact footprint. TECHNICAL DATA Materials: Exterior: 304 Stainless Steel, Bright Finish Interior: Rotationally Molded Polyethylene Electrical: 115 VAC, 60 Hz, 1040 Watts (9.0 Amps) Maximum Inlet Flow Rate: 125 GPM Number of Skimming Wheels: 2 Skimming Rate: 40 Pounds Per Hour Grease Retention Capacity: 300+ Pounds Internal Solids Strainer Capacity: 3.70 Gallons 1/ Greensboro St. Asheboro, N. C Phone (336) North America: (800)
4 Big Dipper IS Central Automatic W-1250-IS Specifications INSTALLATION INFORMATION Suggested Minimum Footprint Dimensions DO... Allow a minimum of 1 clearance from top of tank for removal of unit lid. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown. 52. Make sure the height above the Internal Strainer Access Cover is enough to remove the strainer. Make piping connections with rubber No Hub connectors. Keep outlet piping as straight as possible. Use only sweep connections. Install vent on outlet piping. GC-6 GREASE COLLECTORS Fill the tank with water before energizing the power to the motor and heater. Set Programmable Time Controller for proper operating times. DONʼT... Install P trap on outlet connection of tank. (Note: the unit already has an internal gas trap). Reduce pipe size on outlet piping. Note: Installations must comply with all applicable local, state, and national codes for your area. Job Specification: Grease and oils separator(s) shall be Thermaco Big Dipper automatic grease/oil recovery system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install Thermaco Big Dipper Model No. W-1250-IS, bright finish type 304 stainless steel exterior, rotationally molded polyethylene interior automatic self-cleaning grease and oil recovery separator(s) for floor mounted or partially recessed installation, rated at 125 gallons per minute peak flow, 300 pounds of grease capacity and including as an integral part of the unit, two rotating gear hydrophobic wheel assemblies for automatic grease/ oil removal, an integral flow control device, two self-regulating enclosed electric immersion heaters, a vessel vent, an integral gas trap, two integral programmable 24-hour multi-event time controls, field reversible motor locations, field reversible grease/oil sump outlets, quick release stainless steel lid clamps, a gasketted and fully removable 304 stainless steel lid, lift-out strainer basket access, an internal stainless steel strainer basket for collection of coarse solids, and two separate grease and oils collection containers. Electric assembly shall be tested to comply with pertinent sections of the Standards for Safety ANSI/UL 73 and/or ANSI/UL Each electric motor shall be equipped with thermal overload protection with automatically resettable switch Greensboro St. Asheboro, N. C Phone (336) North America: (800) /06
5 MOTOR/TIMER ENCLOSURE Big Dipper AST Central Automatic W-750-AST Specifications 1 CLEARANCE FROM TOP OF TANK REQUIRED FOR STRAINER BASKET & LID REMOVAL EMPTY INTO COOKING OIL RECYCLING CONTAINER DAILY PIPE / GC-7 GREASE 16.5 COLLECTOR QUART CAPACITY /2 FEMALE NPT WATER SUPPLY CONNECTION FEATURES: END VIEW SIDE VIEW TO WATER SUPPLY 0.5" FEMALE CONNECTOR 45. Fully automatic self cleaning cycle. Removes collected grease, oils and solids from unit without any operator assistance. Comes complete with 24-hour timer Constructed of corrosion resistant materials suitable for installation in virtually any location. Attractive sanitary Stainless Steel exterior Integrated Motor/Grease Outlet/Heater/Lid enables a fast, do-it-yourself unit operation reversal. TOP VIEW Easy lift grease collector simplifies grease collection container emptying. Compact footprint. TECHNICAL DATA Materials: Exterior: 304 Stainless Steel, Bright Finish Interior: Rotationally Molded Polyethylene Electrical: 115 VAC, 60 Hz, 535 Watts (4.6 Amps) Maximum Inlet Flow Rate: 75 GPM Number of Skimming Wheels: 1 Skimming Rate: 20 Pounds Per Hour Grease Retention Capacity: 150+ Pounds Eductor Pump Operation Requirements: 50 PSI min., 12 GPM 1/ Greensboro St. Asheboro, N. C Phone (336) North America: (800)
6 Big Dipper AST Central Automatic W-750-AST Specifications INSTALLATION INFORMATION Suggested Minimum Footprint Dimensions DO... Allow a minimum of 1 clearance from top of tank for removal of unit lid. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown GC-7 GREASE COLLECTOR Provide a min. 50 PSI, 12 GPM Water Supply for solids pump operation Make sure the height above the Internal Strainer Access Cover is enough to remove the strainer. Make piping connections with rubber No Hub connectors. Keep outlet piping as straight as possible. Use only sweep connections. Install vent on outlet piping. Fill the tank with water before energizing the power to the motor and heater. DONʼT... Install P trap on outlet connection of tank. (Note: the unit already has an internal gas trap). Reduce pipe size on outlet piping. Set Programmable Time Controller for proper operating times. Note: Installations must comply with all applicable local, state, and national codes for your area. Job Specification: Grease and oils separator(s) shall be Thermaco Big Dipper automatic grease/oil recovery system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install Thermaco Big Dipper Model No. W-750-AST, bright finish type 304 stainless steel exterior, rotationally molded polyethylene interior automatic self-cleaning grease and oil recovery separator(s) for floor mounted or partially recessed installation, rated at 75 gallons per minute peak flow, 150 pounds of grease capacity and including as an integral part of the unit, 1 rotating gear hydrophobic wheel assembly for automatic grease/oil removal, an integral flow control device, self-regulating enclosed electric immersion heater, a vessel vent, an integral gas trap, an integral programmable 24-hour multi-event time control, a field reversible motor location, a field reversible grease/oil sump outlet, quick release stainless steel lid clamps, a gasketted and fully removable 304 stainless steel lid, lift-out filter basket access, an eductor transfer pump controlled by repeat cycle timer, and a separate grease and oils collection container. Eductor pump shall be supplied with a 0.5 female connector for attachment to facilitysupplied water supply. Eductor pump shall be supplied with an approved vacuum breaker. Electric assembly shall be tested to comply with pertinent sections of the Standards for Safety ANSI/UL 73 and/or ANSI/UL Electric motor shall be equipped with thermal overload protection with automatically resettable switch Greensboro St. Asheboro, N. C Phone (336) North America: (800) /06
7 MOTOR/TIMER ENCLOSURE 24.5 Big Dipper AST Central Automatic W-1250-AST Specifications 1 CLEARANCE FROM TOP OF TANK REQUIRED FOR STRAINER BASKET & LID REMOVAL PIPE / 16.5 DUAL GC-6 GREASE COLLECTORS 6 QUART CAPACITY EA /2 FEMALE NPT WATER SUPPLY CONNECTION FEATURES: END VIEW 5.5 TO WATER SUPPLY 0.5" FEMALE CONNECTOR 52. SIDE VIEW 55. Fully automatic self cleaning cycle. Removes collected grease, oils & solids from tank without any operator assistance. Comes complete with two 24-hour timers Constructed of corrosion resistant materials suitable for installation in virtually any location. Attractive sanitary Stainless Steel exterior. Integrated Motor/Grease Outlet/Heater/Lids enables fast, do-it-yourself unit operation reversal. TOP VIEW Easy lift grease collectors simplify grease collection container emptying. Compact footprint. TECHNICAL DATA Materials: Exterior: 304 Stainless Steel, Bright Finish Interior: Rotationally Molded Polyethylene Electrical: 115 VAC, 60 Hz, 1055 Watts (9.1 Amps) Maximum Inlet Flow Rate: 125 GPM Number of Skimming Wheels: 2 Skimming Rate: 40 Pounds Per Hour Grease Retention Capacity: 300+ Pounds Eductor Pump Operation Water Requirements: 50 PSI min., 12 GPM 1/ Greensboro St. Asheboro, N. C Phone (336) North America: (800)
8 Big Dipper AST Central Automatic W-1250-AST Specifications INSTALLATION INFORMATION Suggested Minimum Footprint Dimensions DO... Allow a minimum of 1 clearance from top of tank for removal of unit lid. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown GC-6 GREASE COLLECTORS Provide a min. 50 PSI, 12 GPM Water Supply for solids pump operation Make sure the height above the Internal Strainer Access Cover is enough to remove the strainer. Make piping connections with rubber No Hub connectors. Keep outlet piping as straight as possible. Use only sweep connections. Install vent on outlet piping. Fill the tank with water before energizing the power to the motor and heater. DONʼT... Job Specification: Install P trap on outlet connection of tank. (Note: the unit already has an internal gas trap). Reduce pipe size on outlet piping. Set Programmable Time Controller for proper operating times. Note: Installations must comply with all applicable local, state, and national codes for your area. Grease and oils separator(s) shall be Thermaco Big Dipper automatic grease/oil recovery system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install Thermaco Big Dipper Model No. W-1250-AST, bright finish type 304 stainless steel exterior, rotationally molded polyethylene interior automatic self-cleaning grease and oil recovery separator(s) for floor mounted or partially recessed installation, rated at 125 gallons per minute peak flow, 300 pounds of grease capacity and including as an integral part of the unit, two rotating gear hydrophobic wheel assemblies for automatic grease/ oil removal, an integral flow control device, two self-regulating enclosed electric immersion heaters, a vessel vent, an integral gas trap, two integral programmable 24-hour multi-event time controls, field reversible motor locations, field reversible grease/oil sump outlets, quick release stainless steel lid clamps, a gasketted and fully removable 304 stainless steel lid, lift-out filter basket access, an eductor transfer pump controlled by repeat cycle timer, and two separate grease and oils collection containers. Eductor pump shall be supplied with a 0.5 female connector for attachment to facility-supplied water supply. Eductor pump shall be supplied with an approved vacuum breaker. Electric assembly shall be tested to comply with pertinent sections of the Standards for Safety ANSI/UL 73 and/or ANSI/UL Each electric motor shall be equipped with thermal overload protection with automatically resettable switch Greensboro St. Asheboro, N. C Phone (336) North America: (800) /06
W-150-IS Specifications
W-150-IS Specifications MOTOR/TIMER ENCLOSURE 14 CLEARANCE FROM TOP OF TANK REQUIRED FOR STRAINER BASKET & LID REMOVAL 10.25 2 PIPE / EMPTY INTO COOKING OIL RECYCLING CONTAINER DAILY GC-7 GREASE 8 QUART
More informationWho Needs BIG DIPPER?
Who Needs BIG DIPPER? Here s how An affordable Big Dipper system solves tough free-floating drainwater problems by removing and recovering up to 98.6% of the grease, oils, fats 1 2 and incidental food
More informationHow To Size A Big Dipper Unit
Sizing Big Dipper Systems In Food Service Operations How To Size A Big Dipper Unit The purpose of this sizing procedure is to give a specifying engineer a simple method for determining the proper size
More information2006 Thermaco, Inc. All rights reserved Patented/Patents Pending Specifications subject to change without notice
One to Three Compartment Sink When planning a multiple fixture discharge into a single Big Dipper, establish the size unit required by following the method outlined in the sizing section of this manual.
More informationInstallation & Operation Instructions For Big Dipper Series Automatic Solids Transfer (AST) Units
Installation & Operation Instructions For Big Dipper 40000 Series Automatic Solids Transfer (AST) Units Models W-250-AST, W-750-AST and W-1250-AST (Including 230 VAC Units) A Big Dipper W-750-AST in a
More informationInnovative, Compact Design
Innovative, Compact Design Easy, Effective Compliance What in the world is? The Thermaco, Inc. Trapzilla Supercapacity Grease Trap collects free-floating (non-emulsifed) grease & oils contained in kitchen
More informationInstallation & Operation Instructions For Big Dipper Series Internal Strainer (IS) Units
Installation & Operation Instructions For Big Dipper 40000 Series Internal Strainer (IS) Units Models W-750-IS and W-1250-IS (Including 230 VAC Units) Big Dipper W-750-IS Installed in a Basement ADA Copyright
More informationAutomatic Solids Transfer System
Automatic Solids Transfer System Models W-300--E, W-500--E, W-750--E, and W-1000--E Automatic Grease/Oils Removal System with Automatic Solids Transfer INSTALLATION AND OPERATIONS MANUAL IPX1 LR110117-1
More informationTHE CLEAR CHOICE FOR CLEANING
THE CLEAR CHOICE FOR CLEANING The Safe, No-Solvent Solution to Cleaning Parts Automatically 509.535.1555 800.727.9128 northstardirect.com info@northstardirect.com 633 N Helena St. Spokane WA 99202 CUDA
More informationCL64T INDUSTRIAL TOTE WASHER
Item # Quantity C.S.I. Section 11400 STANDARD FEATURES Selectable Speed 4, 5, 6 feet/minute Opti-RinSe system Rapid return conveyor drive mechanism Insulated hinged double doors with door interlock switches
More informationProcess Water Heater For Industrial Applications All Voltages, Single or Three Phase Up To 88 KW
MODEL V Process Water Heater For Industrial Applications All Voltages, Single or Three Phase Up To 88 KW Features Industrial Grade Construction Stainless steel pressure vessel provides maximum service
More informationTramp Oil. Removal Equipment Equipment designed for removing oil from water based fluids ERIEZ. ...Only from Eriez. Tramp Oil. Removal Equipment:
...Only from Eriez FB-200B Tramp Oil Removal Equipment: Oil Skimmer Oil Skimmer Jr. Coalescer Tank-Side Coalescer Portable Coalescer Portable Jr. Centrifuge Portable ERIEZ Tramp Oil Removal Equipment Equipment
More information1 Exam Prep Plumber s Handbook Tabs and Highlights
1 Exam Prep Plumber s Handbook Tabs and Highlights These 1 Exam Prep Tabs are based on the Plumber s Handbook Revised 2006. Each Tabs sheet has five rows of tabs. Start with the first tab at the first
More informationOPERATION, INSTALLATION AND MAINTENANCE INSTRUCTIONS SERIES INTERCEPTORS
OPERATION, INSTALLATION AND MAINTENANCE INSTRUCTIONS 5400-5500 SERIES INTERCEPTORS 5401 75 4NH 5500 50 3IPS INSTALLATION Place the Wade interceptor downstream of the drain which will supply the oil laden
More informationCL44eR DISHWASHER STANDARD FEATURES MODEL OPTIONS AT EXTRA COST ACCESSORIES DIRECTION OF OPERATION VOLTAGE. Item # Quantity C.S.I.
Item # Quantity C.S.I. Section 11400 DISHWASHER STANDARD FEATURES Energy recovery 202 racks per hour Opti-RinSe system 30 KW electric booster heater Rapid return conveyor drive mechanism Insulated hinged
More informationFT1000 FLIGHT-TYPE DISHWASHER
Item # Quantity C.S.I. Section 11400 FLIGHT-TYPE DISHER STANDARD FEATURES Pumped rinse system (pressure gauge not required) Water usage 58 gph Digital controls with machine diagnostics Low temperature
More informationUsed Fluid Handling Portable Used Oil Gravity Drains
Portable Used Oil Gravity Drains Choose the fluid handling equipment that fits your needs. Traditional Drain: the traditional method for handling used fluids allows gravity to drain fluids from vehicle(s)
More informationModels. Options. Standard Features. LoH 2 O
LoH O Models LoH O Standard Features Uses 8 gallons (9. liters) of water per hour with sanitizing hot water rinse All tanks and hoods constructed from durable stainless steel with a No. finish and heliarced
More informationFT1000 ENERGY RECOVERY WITH BLOWER DRYER FLIGHT-TYPE DISHWASHER
701 S Ridge Avenue, Troy, OH 45374 Item # Quantity WITH BLOWER DRYER FLIGHT-TYPE DISHER C.S.I. Section 11400 STANDARD FEATURES Pumped rinse system (pressure gauge not required) Water usage 58 gph Digital
More informationAT SERIES C ELECTRIC BOILERS ABSOLUTE EFFICIENCY. TOTAL COMFORT! Save Money, Save Space, Save the Environment! RESIDENTIAL / LIGHT COMMERCIAL
RESIDENTIAL / LIGHT COMMERCIAL ELECTRIC BOILERS Save Money, Save Space, Save the Environment! 100% Efficient Compact Wall Hung Design Zero Emissions, Green Alternative (No Fossil Fuel, No Chimney, No Carbon
More informationUsed Fluid Handling Portable Used-Oil Gravity Drains
Portable Used-Oil Gravity Drains Choose the fluid handling equipment that fits your needs. Traditional Drain: the traditional method for handling used fluids allows gravity to drain fluids from vehicle(s)
More informationFT1000 ENERGY RECOVERY WITH BLOWER DRYER FLIGHT-TYPE DISHWASHER
701 S Ridge Avenue, Troy, OH 45374 Item # Quantity WITH BLOWER DRYER FLIGHT-TYPE DISHER C.S.I. Section 11400 STANDARD FEATURES Pumped rinse system (pressure gauge not required) Water usage 58 gph Digital
More informationJFT Flight Machine. JFT Flight Machine. Models. Options. Standard Features. JFT Flight Machine
JFT Flight Machine Models JFT Flight Machine Options Project Item Quantity CSI Section 00 Approval Date Blower dryer Additional wash section Additional load module Additional unload module (8m) wash down
More informationBOHEC R CRS86A DISHWASHER STANDARD FEATURES MODEL ACCESSORIES DIRECTION OF OPERATION VOLTAGE OPTIONS AT EXTRA COST
Item # Quantity C.S.I. Section 11400 DISHWASHER STANDARD FEATURES 244 racks per hour Opti-RinSe system Ball detent clutch conveyor drive mechanism Top mounted controls Stainless steel anti-clogging wash
More informationIMAGE V. Parts and Service Manual
IMAGE 0V Section II Parts and Service Manual (88B) CLARKE TECHNOLOGY Image Operator's Manual Page AUTHORIZED PERSONNEL MAINTENANCE To Access Pump Motor. Remove brush housing from machine. See "Brush Motor
More informationTitle: YALE OFFICE OF FACILITIES PROCEDURE MANUAL Chapter: 01 - Yale Design Standard Division: HVAC Standards
Date Description of Change Pages / Sections Modified ID 6/15/16 Entire document - mgl44 PART 1 - INTRODUCTION 1.1 PURPOSE A. This section is intended to define the general installation and minimum product
More informationFT1000S BASE FLIGHT-TYPE DISHWASHER
Item # Quantity C.S.I. Section 11400 FLIGHT-TYPE DISHER STANDARD FEATURES Pumped rinse system (pressure gauge not required) Water usage 58 gph Digital controls with machine diagnostics Low temperature
More information1 ESMA, Inc. P. O. BOX 734 * SOUTH HOLLAND, IL * (800) * FAX (708)
1 2 Instructions for Ultrasonic Washer E789 (U.L. Approved) 1. INTRODUCTION The E789 Automatic Ultrasonic Washer automatically performs a cleaning cycle, the major steps of which are: Ultrasonic cleaning
More informationCL64e DISHWASHER DISHWASHER STANDARD FEATURES MODEL OPTIONS AT EXTRA COST ACCESSORIES DIRECTION OF OPERATION VOLTAGE
Item # Quantity C.S.I. Section 11400 DISHWASHER STANDARD FEATURES 342 racks per hour Opti-RinSe system Rapid Return Conveyor Drive Mechanism Insulated hinged double doors with door interlock switches 19.5
More informationTITAN SERIES Complete Central Chiller & Pump Tank Package 20 to 70 Tons 20 F to 70 F
Temperature Control Units Water & Oil - F Portable Chillers Air & Water-Cooled - 7 F Central Chillers Air & Water-Cooled Packages & Modules - 7 F Pump Tank Stations Chilled or Tower Water - gallons Cooling
More informationCLPS66e DISHWASHER DISHWASHER STANDARD FEATURES MODEL OPTIONS AT EXTRA COST ACCESSORIES DIRECTION OF OPERATION VOLTAGE
Item # Quantity C.S.I. Section 11400 DISHWASHER STANDARD FEATURES 202 racks per hour Opti-RinSe system Rapid Return Conveyor Drive Mechanism Insulated hinged double doors with door interlock switches 19.5
More informationPortable CNA-Series - Large Industrial Heaters Tankless Water Heating Solutions
Portable CNA-Series - Large Industrial Heaters Heavy duty industrial cart options simplify moving heater to various locations 36-72 kw (122,800-245,600 BTUs) Certified Lead-Free Design New & Improved Pressure
More informationGLC/GW-100 MANUAL INSTALLATION SERVICE PARTS REV.1.01
Owner s Manual Keep with machine for reference GLC/GW-100 MANUAL INSTALLATION SERVICE PARTS REV.1.01 CMA DISHMACHINES 12700 KNOTT STREET GARDEN GROVE, CALIFORNIA 92841 800-854- 6417 FAX 714-895- 2141 www.cmadishmachines.com
More informationLubrication Tools and Equipment Portable Oil Drains
Portable Oil Drains Choose the fluid handling equipment that fits your needs. Traditional Drain: the traditional method for handling used fluids allows gravity to drain fluids from vehicle(s) into a portable
More informationMARK-COSTELLO WASTE STERILIZER SPECIFICATION SHEET
MARK-COSTELLO WASTE STERILIZER SPECIFICATION SHEET The Mark-Costello Waste Sterilzer is designed and manufactured in accordance with the following specifications: Vessel shall be built in accordance with
More information8070 Mytee Lite. Instructions for. Please read before use. Register your product at support/register.
Instructions for 8070 Mytee Lite Please read before use. Register your product at http://www.mytee.com/ support/register Model # Serial # Form # ADP-8070 06-16 1 GENERAL INFORMATION Dear Customer: Congratulations
More informationVENTLESS DOOR-TYPE DISHWASHER
Item # Quantity C.S.I. Section 11400 VENTLESS STANDARD FEATURES Internal condensing system minimizes water vapor Does not require a vent hood Energy recovery Sense-A-Temp 70 F rise electric booster heater.74
More informationAM SELECT DISHWASHER STANDARD FEATURES MODEL OPTIONS AT EXTRA COST ACCESSORIES VOLTAGE. Item # Quantity C.S.I. Section AM15
AM SELECT DISHWASHER Item # Quantity C.S.I. Section 11400 AM SELECT DISHWASHER STANDARD FEATURES.74 gallons per rack final rinse water 58 racks per hour hot water sanitizing 65 racks per hour chemical
More informationPosi-Drain. A non-clogging straight-through flow path design. Removes condensate, (oil and water) from compressed air systems.
Hydraulics Timer Drain Electric Operated Condensate Drain Posi-Drain A non-clogging straight-through flow path design. Removes condensate, (oil and water) from compressed air systems. Features Straight-through
More informationFT900SDBD DUAL RINSE FLIGHT-TYPE DISHWASHER
Item # Quantity C.S.I. Section 11400 FT900SDBD DUAL RINSE FLIGHT-TYPE DISHWASHER STANDARD FEATURES Opti-RinSe system with dual rinse Water usage 72 gph @ 20 psi Microprocessor controls Low temperature
More informationFreeze Dry Systems and Accessories
Freeze Dry Systems and Accessories Freeze Dry Systems AN OVERVIEW Table of Contents: Overview................................... 1 Selection Guide.............................. 4 FreeZone Freeze Dry Systems
More informationInstallation Instructions. For the 18 Built-In Dishwasher and Front Color Panels
Installation Instructions For the 18 Built-In Dishwasher and Front Color Panels Printed in USA 154232102 Before You Begin DO NOT INSTALL DISHWASHER UNTIL YOU HAVE READ ALL INSTRUCTIONS. FOR YOUR SAFETY,
More informationMODEL A18 SOLVENT RECOVERY SYSTEMS (EXPLOSION PROOF UNITS)
MODEL A18 SOLVENT RECOVERY SYSTEMS (EXPLOSION PROOF UNITS) FOR PROPER AND SAFE USE OF THIS CHEMCHAMP EQUIPMENT, PLEASE FOLLOW THIS DOCUMENT AND LOCAL AUTHORITY. KEEP THIS DOCUMENT FOR FUTURE REFERENCE.
More informationFreeze Dry Systems and Accessories
Freeze Dry Systems and Accessories FreeZone Freeze Dry Systems a n o v e r v i e w Table of Contents: Overview................................... 1 Selection Guide.............................. 4 FreeZone
More informationFT900 FLIGHT-TYPE DISHWASHER
Item # Quantity C.S.I. Section 11400 FT900 FLIGHT-TYPE DISHWASHER STANDARD FEATURES Opti-RinSe system Water usage 120 gph @ 20 psi Microprocessor controls Low temperature alert Single point vent connection
More informationConquest. Condensing Gas Water Heater. 199 to 300 MBH 100 Gallon Tank 15-year Warranty. PVI.com
Conquest Condensing Gas Water Heater E N GI N E E R E D D U P L E X A L L OY 199 to 300 MBH 100 Gallon Tank 15-year Warranty PVI.com Advanced Design with Longer Service Life Conquest is a compact, condensing,
More informationPROVIDES TEPID WATER FOR EMERGENCY SHOWER
PROVIDES TEPID WATER FOR EMERGENCY SHOWER Model EMV FEATURES Heavy Duty Construction Hydrastone cement lining provides tank longevity Copper-silicon alloy tappings cannot rust or corrode High impact composite
More informationGeneral Characteristics.3. S.M.A.R.T System Set-up...5. Start-up Procedures.6. Shut-down Procedures 8. General Maintenance..8
1-800-661-3842 1 TABLE OF CONTENTS General Characteristics.3 How the S.M.A.R.T System Works..3 S.M.A.R.T Technical Specifications..3 Erecting the S.M.A.R.T System..4 S.M.A.R.T System Set-up...5 Start-up
More informationAvailable from. M3 ULTRAf AST. Phone (502) Toll-free (800) Online
M3 ULTRAf AST S IMPLICITY Midmark M3 UltraFast Automatic Sterilizer Exhale...and relax. The Midmark M3 UltraFast Automatic Sterilizer is everything you need in an autoclave. Sterilize unwrapped instruments
More informationFUEL OIL DAY TANKS. SST Level Controller: UL 508 LISTED
FUEL OIL DAY TANKS SST Series - Engineering Submittal SST Series - Advanced Line Day Tanks Construction: UL 142 aboveground steel tank all seam welded, square, atmospheric tank of heavy gauge steel with
More informationCFFWA4P-16-1-U Chilled/Hot Water Universal Mount Fan Coil (4-Pipe) 4-Pipe Heat / Cool Fan Coil 48,000 BTUH
CFFWA4P-16-1-U Chilled/Hot Water Universal Mount Fan Coil (4-Pipe) 4-Pipe Heat / Cool Fan Coil 48,000 BTUH Rev. 1.3 HVAC Guide Specifications Chilled and Hot Water Universal Mount Fan Coil 4-Pipe Nominal
More informationA B A B4
TM TM SERVICE INSTRUCTIONS Thermo-Aire Heater Kits and Air-Heater Assemblies 383808-A4 383808-B4 383880-A4 383880-B4 DESCRIPTION The Thermo-Aire Heater is used in situations where oils of heavier viscosity
More informationCFFWA4P-12-1-U Chilled/Hot Water Universal Mount Fan Coil (4-Pipe) 4-Pipe Heat / Cool Fan Coil 36,000 BTUH
CFFWA4P-12-1-U Chilled/Hot Water Universal Mount Fan Coil (4-Pipe) 4-Pipe Heat / Cool Fan Coil 36,000 BTUH Rev. 1.3 HVAC Guide Specifications Chilled and Hot Water Universal Mount Fan Coil 4-Pipe Nominal
More informationTURBOWASH TM... Pot and Pan Sink
TURBOWASH TM... Pot and Pan Sink MODEL TW ML-110644 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 33800 Rev. A (4-98) Installation, Operation, and Care of TurboWash TM Pot and Pan Sink SAVE THESE INSTRUCTIS
More informationC44A/C44AW DISHWASHER
Item # Quantity C.S.I. Section 11400 C44A/C44AW DISHWASHER STANDARD FEATURES 202 racks per hour C44A 126 racks per hour C44AW Opti-RinSe system Ball detent clutch conveyor drive mechanism Top mounted controls
More informationCFFWA4P-08-1-U Chilled/Hot Water Universal Mount Fan Coil (4-Pipe) 4-Pipe Heat / Cool Fan Coil 24,000 BTUH
CFFWA4P-08-1-U Chilled/Hot Water Universal Mount Fan Coil (4-Pipe) 4-Pipe Heat / Cool Fan Coil 24,000 BTUH Rev. 1.3 HVAC Guide Specifications Chilled and Hot Water Universal Mount Fan Coil 4-Pipe Nominal
More informationTFC 400. OPERATOR MANUAL Clarke MODEL /09 Rev C Document Number
TFC 400 OPERATOR MANUAL Clarke MODEL 56380773 1 11/09 Rev C Document Number 56380889 IMPORTANT SAFETY INSTRUCTIONS This machine is only suitable for commercial use, for example, in hotels, schools, hospitals,
More informationFT900BD FLIGHT-TYPE DISHWASHER
Item # Quantity C.S.I. Section 11400 FT900BD FLIGHT-TYPE DISHWASHER STANDARD FEATURES Opti-RinSe system Water usage 120 gph @ 20 psi Microprocessor controls Low temperature alert Blower dryer with 2 H.P.
More informationFT900D DUAL RINSE FLIGHT-TYPE DISHWASHER
Item # Quantity C.S.I. Section 11400 FT900D DUAL RINSE FLIGHT-TYPE DISHWASHER STANDARD FEATURES Opti-RinSe system with dual rinse Water usage 90 gph @ 20 psi Microprocessor controls Low temperature alert
More informationBEFORE OPERATING THE MACHINE: WARNING
BEFORE OPERATING THE MACHINE: Read the manual carefully and completely before attempting to operate the unit. This manual has important information for the use and safe operation of the machine. Keep this
More informationResidential Fire Meter
Residential Fire Meter Features APPLICATIONS: The Hersey Residential Fire Meter (RFM) is specifically designed for use in residential fire protection systems or combination systems that supply domestic
More informationC. ASSE 1013: Performance Requirements for Reduced Pressure Principle Backflow Preventers.
SECTION 22 10 00 PLUMBING PIPING AND PUMPS PART 1 - GENERAL 1.1 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design.
More informationStandard Features. Performance/Capacities
TSC-66 Traditional Power/Connections Approximate Total Load AMPS 208V / 60HZ / 3PH 51.8 208V / 60HZ / 1PH 88.3 230V / 60HZ / 3PH 47.8 230V / 60HZ / 1PH 81.5 460V / 60HZ / 3PH 23.9 Booster Heater Options
More informationSERVICE MANUAL. Bradford White ElectriFLEX HD (Heavy Duty) Commercial Electric Water Heater CEHD SERIES Immersion Thermostat Models
Bradford White ElectriFLEX HD (Heavy Duty) Commercial Electric Water Heater CEHD SERIES Immersion Thermostat Models SERVICE MANUAL Troubleshooting Guide and Instructions for Service (To be performed ONLY
More informationTemptek Auxiliary Equipment
Temptek Auxiliary Equipment Mold Temperature Controllers - Water Units VT-275-LX VT Series Mold Temperature Controllers are used to process temperature control to 250 F. These units use an incoloy heater
More informationFiberPRO. 15 Series. High Pressure Carpet Extractors. Operator and Parts Manual E E E
E29977-00 E29979-00 E29978-00 FiberPRO 15 Series High Pressure Carpet Extractors Operator and Parts Manual 1001 Brown Avenue Toledo, Ohio 43607-0127 Customer Service: 888-GO-BETCO Fax: 800-445-5056 Technical
More information6-Gallon Carpet Extractor Series
Limited Warranty CleanFreak warrants new equipment against defects in material and workmanship under normal use and service to the original purchaser. Any statutory implied warranties, including any warranty
More informationPartswasher and Workshop Solutions COMMERCIAL
Partswasher and Workshop Solutions COMMERCIAL NEW ZEALAND S NATIONAL SUPPLIER OF COMPREHENSIVE PARTSWASHER AND WORKSHOP WASTE SOLUTIONS Partswashers Companies need assurance that their machinery, including
More informationEffectively clean rubber footwear with a BSX Boot Scrubber
Effectively clean rubber footwear with a BSX Boot Scrubber Each of the BSX Boot Scrubbers use an open, sanitary design which eliminates hidden and hard to reach areas that are difficult to clean and can
More informationGetz Equipment Innovators 450 lb Dual Portable Dry Chemical Fill System
Getz Equipment Innovators 450 lb Dual Portable Dry Chemical Fill System 1 Revised 11/18/10 2320 Lakecrest Drive, Pekin IL 61554 PH. (888) 747-4389 Fax (309) 495-0625 Website: www.getzequipment.com LIMITED
More informationConveyor. AJ-44 Vision Series. Standard Features. Power/Connections. Performance/Capacities
AJ-44 Vision Series Standard Features Power/Connections Approximate Total Load AMPS 208V / 60HZ / 3PH 48.4 208V / 60HZ / 1PH 82.3 230V / 60HZ / 3PH 44.4 230V / 60HZ / 1PH 75.5 460V / 60HZ / 3PH 22. 2 Booster
More informationDEMA SOLID PRODUCT LAUNDRY MASTER TM MODEL: 581L-1W and 581L-2W INSTALLATION INSTRUCTIONS
Included Parts: A. 581.1 Solid Bowl B. 58.1LA Vacuum Breaker C. 58.6 Stainless Steel Supply Tube D. 58.29 90º Compression Fitting E. 58.24 Straight Compression Fitting F. 58.7 Vinyl Discharge Tube G. 66.123
More information"ESDDR" Series Electric Humidifier
ESDDR-1 Deionized, Demineralized, or Reverse Osmosis Water "ESDDR" Series Electric Humidifier The Electric Humidifier from PURE Humidifier Co. is loaded with features and options. All you need is deionized,
More informationELECTRIC SPRAYER OWNER S MANUAL
ATOMIST ELECTRIC SPRAYER OWNER S MANUAL MODEL 1952B OPERATION: ATOMIST ELECTRIC SPRAYER IMPORTANT! Before operating your Atomist, read the following instructions carefully DO NOT operate this spryer in
More informationInstructions for Model E782 Betman Cleaning System (Cleaner/Rinser/Rinser/Dryer)
1 2 Esma Inc. PO Box 734 450 W. Taft Drive South Holland, IL 60473 708-331-1855 800-276-2466 FAX 708-331-8919 Introduction Instructions for Model E782 Betman Cleaning System (Cleaner/Rinser/Rinser/Dryer)
More informationFLOOD KING 120V. 2. Keep all filters clean. Do not operate the machine if the filters are clogged.
FLOOD KING 120V INFORMATION & OPERATING INSTRUCTIONS DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THESE INSTRUCTIONS. IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY 1. Always be sure
More informationWallace & Tiernan Gas Feed Systems V2000 Chlorinator
Wallace & Tiernan Gas Feed Systems V2000 Chlorinator Introduction Siemens Water Technologies chlorination equipment has the benefit of 100 years of experience in gas feed technology. V2000 chlorinators
More information3500 SERIES CONVECTION STEAM COOKER PARTS AND SERVICE MANUAL
3500 SERIES CONVECTION STEAM COOKER PARTS AND SERVICE MANUAL EFFECTIVE JULY 30, 2014 Superseding All Previous Parts Lists. The Company reserves the right to make substitution in the event that items specified
More informationEB-M*-** Midsize Electro-Boiler BL509. EB-S-**/EB-WX-**-2 TS Standard Electro-Boiler BL506. EB-CX-** TS Commercial Electro-Boiler BL508
Electro-HELPS IX Boiler, Submittal Data Sheets These provide the mechanical technical details often required for architects/design engineers, shop drawings, etc. They are also useful in providing additional
More informationSUPPORT EQUIPMENT MODULAR RAPIDLY DEPLOYABLE MOBILE RUGGED RELIABLE VERSATILE
SUPPORT EQUIPMENT MODULAR RAPIDLY DEPLOYABLE MOBILE RUGGED RELIABLE VERSATILE SUPPORT EQUIPMENT Deployable Rapid Assembly Shelter (DRASH) Support Equipment are shelter components that can be used to enhance
More informationTERMINATOR 120V CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THIS INSTRUCTION MANUAL
TERMINATOR 120V INFORMATION & OPERATING INSTRUCTIONS CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THIS INSTRUCTION MANUAL 56041962 IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY
More informationMYTEE PRODUCT GUIDE EXTRACTORS. Revised February FAX ORDERS: CALLS:
EXTRACTORS MYTEE PRODUCT GUIDE Revised February 2017 EXTRACTORS Speedster Speedster LTD Contractor s Special Special Breeze Model 1000DX-200 1001DX-200 1003DX 1005DX LTD3 LTD5 LTD12 2002CS BZ-104 10 gallon
More informationModel GW1020 Laboratory Glassware Washer General Specifications
Model GW1020 Laboratory Glassware Washer General Specifications 1.0 General Description The Model GW1020 Laboratory Glassware Washer is a high capacity spray cabinet washer specifically designed to clean
More informationIndirect Fired Water Heater
Indirect Fired Water Heater 35-119 Gallon Capacities Features Heavy Duty Construction Hydrastone cement lining provides long tank life Copper-silicon tappings cannot rust or corrode High impact composite
More informationRaffaello From serial number Group
Group 1 C199900260 Solenoid valve V.230/50-60 1 C199900261 Solenoid valve, V. 115/60 2 C449900786 O-Ring 3 C229900553 Nut 4 C449900079 O-Ring 5 C619900554 Metal filter 6 C229900549 Gigleur 7 C229900674
More informationINTEGRATED CLEANING SYSTEM TOUCHLESS CLEANING SOLUTIONS
improve appearance & sanitary standards, motivate employees & increase productivity in: 4 easy steps 1 Select 2 Spray 3 Rinse and 4 Squeege it s as simple as that! Fast, simple set up allows you to quickly
More informationVacuum Oil Purifier (VOP) (5 Pages. June 2017)
Vacuum Oil Purifier (VOP) (5 Pages. June 2017) The best designed Vacuum Oil Purifier made, combining simple operation with higher performance, creating more value for your investment. 1. 304 Stainless
More informationCommercial Hot Water Maker
Boiler Mate Series Commercial Hot Water Maker Indirect-Fired Water Heaters Models WH-7C and WH-10C 1 INNOVATIVE DESIGN FOR REAL WORLD APPLICATIONS The Boiler Mate Series commercial Hot Water Maker design
More informationTM Series. Induced Draft, Counter Flow Optional Accessories
ANTIFREEZE PACKAGE / RESISTANCE HEATING OPTION The antifreeze package is supplied to provide protection against freezing of standing water in the cooling tower sump due to shutdown during winter operation.
More informationONQUEST. Featuring... Condensing Water Heater. Requires no tank linings or heat exchanger linings. Requires no anodes of any type. 10- year warranty.
R C ONQUEST TM Condensing Water Heater UP TO 97% THERMAL EFFICIENCY AT FULL RATE FROM 40 F TO 140 F TANK AND HEAT EXCHANGER MADE FROM AquaPLEX ENGINEERED DUPLEX STAINLESS STEEL ALLOY Featuring... SEAMLESS
More informationParagon. Induced Draft, Counter Flow Optional Accessories
ANTIFREEZE PACKAGE / RESISTANCE HEATING OPTION The antifreeze package is supplied to provide protection against freezing of standing water in the cooling tower sump due to shutdown during winter operation.
More informationMODEL 6430T, 6460 & 6460T POTATO PEELER
MODEL 6430T, 6460 & 6460T POTATO PEELER MODEL ML-137602 6430T ML-19630 6460 ML-137604 6460T ML-104562 6460C ML-137606 6460CT 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 37005 (Apr. 2006) Installation,
More informationFT1000S ENERGY RECOVERY STEAM Flight-Type Dishwashing Machine FT SERIES FT1000S ENERGY RECOVERY STEAM STANDARD FEATURES SPECIFIER STATEMENT
Project AIA # SIS # Item # Quantity C.S.I. Section 114000 COMMERCIAL DISHERS FT1000S ENERGY RECOVERY STEAM LA Research Report M660004 Complies with EPA Reduction of Lead in Drinking Water Act 2014 Meets
More informationVACUUM EXTRACTOR MODEL NO: CWVE1 OPERATING & MAINTENANCE INSTRUCTIONS PART NO: GC0916
VACUUM EXTRACTOR MODEL NO: CWVE1 PART NO: 6471168 OPERATING & MAINTENANCE INSTRUCTIONS GC0916 INTRODUCTION Thank you for purchasing this CLARKE Workshop Vacuum Extractor. Before attempting to use this
More information1600 Series Rotating Suction Screen
INTRODUCTION The 1600 Series Rotating Suction Screen is an Electric Motor (Hydraulic Option Available) driven, Self-Cleaning Suction Screen. It is ideally used for pumping water from canals, reservoirs,
More informationSYSTEM DESIGN REQUIREMENTS
P a g e 1 SYSTEM DESIGN REQUIREMENTS WFC-S SERIES WATER-FIRED SINGLE-EFFECT ABSORPTION CHILLERS / CHILLER-HEATERS Yazaki WFC-S Series water-fired chillers and chiller-heaters are available with nominal
More informationCanning Shed/Facility Equipment Specifications
Canning Shed/Facility Equipment Specifications Item Qty Description 1 1 ea WALK IN COOLER Fast Trak Indoor One Compartment Walk In, 8' x 8' x 7' 7" H, compartments, cooler with smooth aluminum interior
More informationVent-Rite. Cast Iron And Steel Receivers. Simplex, Duplex, Triplex And Quadruplex Units. Pump Capacities To 150 GPM. Discharge Pressure To 75 PSI
Vent-Rite BULLETIN VCRV AUGUST 0 GUARDIAN Plus Cast Iron And Steel Receivers Simplex, Duplex, Triplex And Quadruplex Units Pump Capacities To 0 GPM Discharge Pressure To 7 PSI 87 Dewey Avenue Benton Harbor,
More informationJabsco Marine Toilets SIMPLY RELIABLE SOLUTIONS FOR EVERY BOAT AND BUDGET
Jabsco Marine Toilets SIMPLY RELIABLE SOLUTIONS FOR EVERY BOAT AND BUDGET 3 From best-selling manual toilets to household-style luxury models, our marine toilets are both simple and reliable. All toilet
More informationThere are a few factors critical in the operation of a grease interceptor, which are: Design, Sizing, Proper installation and maintenance.
TEL: 773-341-3030 FAX: 773-341-3046 TOLL FREE: 1-800-465-2736 WEBSITE: www.mifab.com Grease Interceptors Description of Operation: There are a few factors critical in the operation of a grease interceptor,
More information