SERIES 15 HEAT PUMP WITH PURON

Transcription

1 MODEL PREFERRED ERIE 15 HEAT PUMP WITH PURON REFRIGERANT 1-1/2 TO 5 NOMINAL TON Product Data the environmentally sound refrigerant Bryant s heat pumps with r refrigerant provide a collection of features unmatched by any other family of equipment. The has been designed utilizing Bryant s refrigerant. The environmentally sound refrigerant allows consumers to make a responsible decision in the protection of the earth s ozone layer. As an Energy tarr Partner, Bryant Heating & Cooling ystems has determined that this product meets the Energy tar r guidelines for energy efficiency. Refer to the combination ratings in the Product Data for system combinations that meet Energy tarr guidelines. NOTE: Ratings contained in this document are subject to change at any time. Always refer to the AHRI directory ( for the most up -to -date ratings information. TM INDUTRY LEADING FEATURE / BENEFIT Efficiency ound Comfort EER/ EER/ HPF (Nominal) Microtube Technologyt refrigeration system Indoor air quality accessories available ound level as low as 68 dba ystem supports Thermidistatt or standard thermostat controls Reliability Durability r refrigerant - environmentally sound, won t deplete the ozone layer and low lifetime service cost. Front -seating service valves croll compressor Internal pressure relief valve Internal thermal overload High pressure switch Loss of charge switch Filter drier Balanced refrigeration system for maximum reliability DuraGuard Plust protection package: olid, durable sheet metal construction teel louver coil guard Baked -on, complete coverage, powder paint Applications Long -line - up to 250 feet (76.20 m) total equivalent length, up to 200 feet (60.96 m) condenser above evaporator, or up to 80 ft. (24.38 m) evaporator above condenser (ee Longline Guide for more information.) Low ambient (down to -20_F/-28.9_C) with accessory kit

2 MODEL NUMBER NOMENCLATURE N N N A A/N N N N N A/N A/N N A B N A A Product Tier EER Major Voltage Variations Cooling Capacity Open Open Open eries Family eries 2=HP 2= Legacy eries 5=15 EER B= N= or 208/ A=tandard 0=Not Defined 0=Not Defined 0=Not Defined A = Original eries the environmentally sound refrigerant Use of the AHRI Certified TM Mark indicates a manufacturer s participation in the program For verification of certification for individual products, go to This product has been designed and manufactured to meet Energy tar criteria for energy efficiency when matched with appropriate coil components. However, proper refrigerant charge and proper air flow are critical to achieve rated capacity and efficiency. Installation of this product should follow all manufacturing refrigerant charging and air flow instructions. Failure to confirm proper charge and air flow may reduce energy efficiency and shorten equipment life. TANDARD FEATURE Feature Refrigerant X X X X X X X Maximum EER Rating* croll Compressor X X X X X X X Louvered Coil Guard X X X X X X X FieldInstalledFilterDrier X X X X X X X Front eating ervice Valves X X X X X X X Internal Pressure Relief Valve X X X X X X X Internal Thermal Overload X X X X X X X Long Line capability X X X X X X X Low Ambient capability with Kit X X X X X X X uction Line Accumulator X X X X X X X High Pressure witch X X X X X X X Loss of Charge witch X X X X X X X * Based on tested combination ratings X=tandard 2

3 PHYICAL DATA UNIT IZE ERIE A A A A A A A Operating Weight lb (kg) hipping Weight lb (kg) Compressor Type croll REFRIGERANT R---410A Control TXV (R---410A Hard hutoff) Charge (lb) COND FAN Propeller Type, Direct Drive Air Discharge Vertical Air Qty () Motor HP 1/12 1/12 1/12 1/5 1/5 1/4 1/4 Motor RPM COND COIL Face Area (q ft) Fins per In Rows Circuits VALVECONNECT.(In.ID) Vapor 5/8 5/8 3/4 3/4 7/8 7/8 7/8 Liquid 3/8 REFRIGERANT TUBE (In. OD) Rated Vapor* 5/8 5/8 3/4 3/4 7/8 7/ /8 Max Liquid Line 3/8 *Units are rated with 25 ft (7.6 m) of lineset length. ee Vapor Line izing and Cooling Capacity Loss table when using other sizes and lengths of lineset. Note: ee unit Installation Instruction for proper installation. VAPOR LINE IZING AND COOLING CAPACITY LO Acceptable vapor line diameters provide adequate oil return to the compressor while avoiding excessive capacity loss. The suction line diameters shown in the chart below are acceptable for HP systems with refrigerant: Unit Nominal ize (Btuh) Maximum Liquid Line Diameters (In. OD) VAPOR LINE IZING AND COOLING CAPACITY LOE - PURONR REFRIGERANT 1 - TAGE HEAT PUMP APPLICATION Vapor Line Diameters (In.) OD ( ) tandard Application ( ) ( ) Cooling Capacity Loss (%) Total Equivalent Line Length ft. (m) ( ) Long Line Application Requires Accessories ( ) ( ) ( ) ( ) ( ) 18,000 1/ tage 3/8 HP with 5/ ,000 5/ tage 3/8 HP with 3/ ,000 5/ tage HP with 3/8 3/ / ,000 5/ tage HP with 3/8 3/ / ,000 3/ tage 3/8 HP with 7/ ,000 3/ tage 3/8 HP with 7/ ,000+ 3/ tage HP with 3/8 7/ / tandard Length = 80 ft. (24.4 m) or less total equivalent length Applications in this area are long line. Accessories are required as shown recommended on Long Line Application Guidelines Applications in this area may have height restrictions that limit allowable total equivalent length, when outdoor unit is below indoor unit ee Long Line Application Guidelines 3

4 REFRIGERANT PIPING LENGTH LIMITATION Maximum Line Lengths: The maximum allowable total equivalent length for heat pumps varies depending on the vertical separation. allowable lengths depending on whether the outdoor unit is on the same level, above or below the outdoor unit. ee the tables below for MAXIMUM LINE LENGTH FOR HEAT PUMP APPLICATION MAXIMUM ACTUAL LENGTH ft (m) MAXIMUM EQUIVALENT LENGTH{ ft (m) MAXIMUM VERTICAL EPARATION ft (m) Units on equal level 200 (61) 250 (76.2) N/A Outdoor unit ABOVE indoor unit 200 (61) 250 (76.2) 200 (61) Outdoor unit BELOW indoor unit ee Table Maximum Total Equivalent Length: Outdoor Unit BELOW Indoor Unit { Total equivalent length accounts for losses due to elbows or fitting. ee the Long Line Guideline for details. ize Liquid Line Diameter w/ TXV MAXIMUM TOTAL EQUIVALENT LENGTH { - OUTDOOR UNIT BELOW INDOOR UNIT ( ) ( ) HP with r Refrigerant --- Maximum Total Equivalent Length{ Vertical eparation ft (m) Outdoor unit BELOW indoor unit; ( ) ( ) ( ) ( ) ( ) HP with 3/8 250* 250* 250* 250* 250* 250* 250* HP with 3/8 250* 250* 250* 250* 250* 250* 250* HP with 3/8 250* 250* 250* 250* 250* 250* 250* HP with 3/8 250* 250* 250* 250* 250* 250* 250* HP with 3/8 250* 250* 250* 250* 250* 250* HP with 3/8 250* 250* 250* 250* HP with 3/8 250* 225* * Maximum actual length not to exceed 200 ft (61 m) { Total equivalent length accounts for losses due to elbows or fitting. ee the Long Line Guideline for details = outside acceptable range LONG LINE APPLICATION An application is considered Long Line when the refrigerant level in the system requires the use of accessories to maintain acceptable refrigerant management for systems reliability. Defining a system as long line depends on the liquid line diameter, actual length of the tubing, and vertical separation between the indoor and outdoor units. For Heat Pump systems, the chart below shows when an application is considered Long Line. Beyond these lengths, long line accessories are required: HP WITH PURONR REFRIGERANT LONG LINE DECRIPTION FT (M) BEYOND THEE LENGTH, LONG LINE ACCEORIE ARE REQUIRED Liquid Line ize Units On ame Level Outdoor Below Indoor Outdoor Above Indoor 3/8 80 (24.4) 20 (6.1) vertical or 80 (24.4) total 80 (24.4) Note: eelonglineguidelinefordetails 4

5 ACCEORIE ORDER NUMBER DECRIPTION A A A A A A A KAACH1701AAA CRANKCAE HTR X X X KAACH1401AAA CRANKCAE HTR X KAACH1601AAA CRANKCAE HTR X KAACH1201AAA CRANKCAE HTR X tandard CRANKCAE HTR KACY0101AAA CYCLE PROTECTOR X X X X X X X KAAFT0101AAA FREEZE THERMOTAT X X X X X X X KAH1701AAA HARD TART (CAP/RELAY) X X X X X X X KHAIR0101AAA IOLATION RELAY X X X X X X X KALA LOW AMBIENT PW X X X X X X X HC32GE229 MOTOR FAN BALL BEARING X X X HC38GE228 MOTOR FAN BALL BEARING X X HC40GE228 MOTOR FAN BALL BEARING X X KALA0601AAA MOTORMATER 230V X X X X X X X KHAOT0201EC OUTDOOR THERMOTAT X X X X X X X KHAOT0301FT OUTDOOR THERMOTAT X X X X X X X KHA0606MPK* HEAT PUMP NOW RACK X X X X X X X KHAL0401LL OLENOID VALVE X X X X X X X KAAC0201PTC TARTAITPTC X X X X X X X KAF0101AAA UPPORT FEET X X X X X X X KAATD0101TDR TIME DELAY X X X X X X X KATX0201PUR TXV PURON HO X X X KATX0301PUR TXV PURON HO X X KATX0401PUR TXV PURON HO X KATX0501PUR TXV PURON HO X x = Accessory = tandard * Order through RCD---Totaline, part number KHA0606MPK (qty 6). ACCEORY THERMOTAT PART NUMBER PROGRAM GA ELECTRIC HEAT PUMP HYBRID HEAT T6 --- PRH A Day 3 2 T6---PHP Day 3 2 T6 --- NRH A NP 3 2 T6 --- NHP01 NP 3 2 THERMOTAT ACCEORIE PART NUMBER BRIEF DECRIPTION THERMOTAT UED WITH YTXBBRR01 Indoor Remote Room Temperature ensor All T6 --- thermostats T6 --- EXP A ExPr Computer Programming Accessory T6---P thermostats TTATXXCNV10 Thermostat Conversion Kit (4 to 5 wire) pack All Bryantr branded thermostats TX --- LBP01 LargeDecorativeBackplate T6 --- Pxx, T6 --- Nxx, and T2 --- Pxx TTATXXEN01---B Outdoor Air Temperature ensor All T6 --- thermostats HEAT COOL 5

6 ACCEORY UAGE GUIDELINE Accessory REQUIRED FOR LOW---AMBIENT COOLING APPLICATION (Below 55 F / 12.8 C) REQUIRED FOR LONG LINE APPLICATION* REQUIRED FOR EA COAT APPLICATION (Within 2 miles / 3.22 km) Accumulator tandard tandard tandard Ball Bearing Fan Motor Yes{ No No Compressor tart Assist Capacitor and Relay Yes Yes No Crankcase Heater Yes Yes No Evaporator Freeze Thermostat Yes No No Hard hutoff TXV Yes Yes Yes Isolation Relay Yes No No Liquid Line olenoid Valve No ee Long---Line Application Guideline No Motor Master Control or Low Ambient witch Yes No No upport Feet Recommended No Recommended * For tubing line sets between 80 and 200 ft. (24.38 and m) and/or 20 ft. (6.09 m) vertical differential, refer to Residential Piping and Longline Guideline. { Additional requirement for Low---Ambient Controller (full modulation feature) MotorMasterr Control. Accessory Description and Usage (Listed Alphabetically) 1. Ball-Bearing Fan Motor A fan motor with ball bearings which permits speed reduction while maintaining bearing lubrication. Required on all units when using MotorMasterr 2. Compressor tart Assist - Capacitor and Relay tart capacitor and relay gives a hard boost to compressor motor at each start up. Required for reciprocating compressors in the following applications: Long line Low ambient cooling Hard shut off expansion valve on indoor coil Liquid line solenoid on indoor coil Required for single-phase scroll compressors in the following applications: Long line Low ambient cooling uggested for all compressors in areas with a history of low voltage problems. 3. Compressor tart Assist PTC Type olid state electrical device which gives a soft boost to the compressor at each start -up. uggested in installations with marginal power supply. 4. Crankcase Heater An electric resistance heater which mounts to the base of the compressor to keep the lubricant warm during off cycles. Improves compressor lubrication on restart and minimizes the chance of liquid slugging. Required in low ambient cooling applications. Required in long line applications. uggested in all commercial applications. 5. Evaporator Freeze Thermostat An PT temperature-actuated switch that stops unit operation when evaporator reaches freeze -up conditions. Required when low ambient kit has been added. 6. Isolation Relay An PDT relay which switches the low -ambient controller out of the outdoor fan motor circuit when the heat pump switches to heating mode. Required in all heat pumps where low ambient kit has been added. 7. Liquid -Line olenoid Valve (LL) An electrically operated shutoff valve which stops and starts refrigerant liquid flow in response to compressor operation. It is to be installed at the outdoor unit to control refrigerant off cycle migration in the heating mode. An LL is required in all long line heat pump applications to control refrigerant off cycle migration in the heating mode. ee Long Line Guideline. 8. Low -Ambient Pressure witch Kit A long life pressure switch which is mounted to outdoor unit service valve. It is designed to cycle the outdoor fan motor in order to maintain head pressure within normal operating limits. The control will maintain working head pressure at low -ambient temperatures down to 0_F (-17.8_C)when properly installed. A Low -Ambient Pressure witch or MotorMasterr Low -Ambient Controller must be used when cooling operation is used at outdoor temperatures below 55_F (12.8_C). 9. MotorMasterr Low -Ambient Controller A fan -speed control device activated by a temperature sensor, designed to control condenser fan motor speed in response to the saturated, condensing temperature during operation in cooling mode only. For outdoor temperatures down to -20_F (-28.9_C), it maintains condensing temperature at 100_F ±10_F (37.8_C ± 6.5_C). A MotorMasterr Low Ambient Controller or Low -Ambient Pressure witch must be used when cooling operation is used at outdoor temperatures below 55_F (12.8_C). uggested for all commercial applications. 6

7 Accessory Description and Usage (Listed Alphabetically) - CONTINUED 10. Outdoor Air Temperature ensor Designed for use with Bryant Thermostats listed in this publication. This device enables the thermostat to display the outdoor temperature. This device also is required to enable special thermostat features such as auxiliary heat lock out. uggested for all Bryant thermostats listed in this publication. 11. Outdoor Thermostat An PDT temperature -actuated switch which turns on supplemental electric heaters when outdoor air temperature drops below a user-selected set point. Electric supplemental heat applications in non -variable speed indoor units when electric heat staging is desired. 12. econdary Outdoor Thermostat An PDT temperature -actuated switch which turns on third -stage of supplemental electric heaters when outdoor air temperature drops below the second -stage set point. Outdoor thermostat applications where electric heater is capable of three-stage operation. 13. now tand Coated wire rack which supports unit 18 in. (457.2 mm) above mounting pad to allow for drainage from unit base. uggested in the following applications: Heat pump installations in heavy snowfall areas. Heat pump installations in snow drift locations. Heat pump installations in areas of prolonged subfreezing temperatures. All commercial installations. 14. Thermostatic Expansion Valve (TXV) Bi-Flow A modulating flow -control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving the evaporator. Accessory required to meet AHRI rating and system reliability, where indoor not equipped. Required in all heat pump applications designed with refrigerant. 15. Time-Delay Relay An PT delay relay which briefly continues operation of indoor blower motor to provide additional cooling after the compressor cycles off. Note: Most indoor unit controls include this feature. For those that do not, use the guideline below. Accessory required to meet AHRI rating, where indoor not equipped. 7

8 ELECTRICAL DATA UNIT IZE V/PH OPER VOLT* COMPR FAN MCA MIN WIRE IZE{ MIN WIRE IZE{ MAX LENGTH ft (m) MAX LENGTH ft (m) MAX MIN LRA RLA FLA 60 C 75 C 60 C 75 C MAX FUE** or CKT BRK AMP A (20.4) 63 (19.2) A (14.6) 45 (13.7) A ( (12.5) A 208/230/ (17.4) 54 (16.5) A (21.9) 69 (21.0) A (21.3) 67 (20.4) A (27.7) 56 (17.1) 50 * Permissible limits of the voltage range at which the unit will operate satisfactorily { If wire is applied at ambient greater than 30_C, consult table of the NEC (ANI/NFPA 70). The ampacity of non---metallic---sheathed cable (NM), trade name ROMEX, shall be that of 60_C conditions, per the NEC (ANI/NFPA 70) Article If other than uncoated (no---plated), 60 or 75_C insulation, copper wire (solid wire for 10 AWG or smaller, stranded wire for larger than 10 AWG) is used, consult applicable tables of the NEC (ANI/NFPA 70). } Length shown is as measured 1 way along wire path between unit and service panel for voltage drop not to exceed 2%. ** Time --- Delay fuse. FLA --- Full Load Amps LRA --- Locked Rotor Amps MCA --- Minimum Circuit Amps RLA --- RatedLoadAmps NOTE: Control circuit is 24---V on all units and requires external power source. Copper wire must be used from service disconnect to unit. All motors/compressors contain internal overload protection. Complies with 2007 requirements of AHRAE tandards 90.1 A -WEIGHTED OUND POWER UNIT IZE --- VOLTAGE, ERIE TANDARD RATING (dba) TYPICAL OCTAVE BAND PECTRUM (dba, without tone adjustment) A A A A A A A NOTE: Tested in accordance with AHRI tandard (not listed in AHRI). CHARGING UBCOOLING (TXV -TYPE EXPANION DEVICE) UNIT IZE--- VOLTAGE, ERIE REQUIRED UBCOOLING F ( C) A 12 (6.7) A 14 (7.8) A 10 (5.6) A 8 (4.4) A 10 (5.6) A 11 (6.1) A 10 (5.6) 8

9 DIMENION - ENGLIH UNIT ERIE ELECTRICAL CHARACTERITIC A B C D E F G K L M N P OPERATING WEIGHT (lbs) HIPPING WEIGHT (lbs) HIPPING DIMENION (L x W x H) 018 A X O O O 31 3/16" 28 15/16" 3 3/4" 5/8" 6 9/16" 24 11/16" 9 1/8" 2 13/16" 1/2" 16" 15" 14" /16" X 35 1/2" X 32 9/16" 024 A X O O O 35" 32 5/16" 3 3/4" 5/8" 6 9/16" 28 7/16" 9 1/8" 2 13/16" 1/2" 15 3/4" 16 3/4" 16 1/2" /8" X 39 1/4" X 35 15/16" 030 A X O O O 35" 32 5/16" 3 3/4" 3/4" 6 9/16" 28 7/16" 9 1/8" 2 13/16" 1/2" 16 1/4" 16" 15 1/2" /8" X 39 1/4" X 35 15/16" 036 A X O O O 35" 35 3/4" 3 3/4" 3/4" 6 9/16" 28 7/16" 9 1/8" 2 13/16" 1/2" 15 3/4" 16 3/4" 17" /8" X 39 1/4" X 39 3/8" 042 A X O O O 35" 28 15/16" 3 7/8" 7/8" 6 9/16" 28 7/16" 9 1/8" 2 15/16" 5/8" 17" 16 3/4" 14 3/4" /8" X 39 1/4" X 32 9/16" 048 A X O O O 35" 28 15/16" 3 7/8" 7/8" 6 9/16" 28 7/16" 9 1/8" 2 15/16" 5/8" 16 3/4" 16 1/4" 14" /8" X 39 1/4" X 32 9/16" 060 A X O O O 35" 39 1/8" 3 7/8" 7/8" 6 9/16" 28 7/16" 9 1/8" 2 15/16" 5/8" 17 1/4" 16 1/4" 18 1/4" /8" X 39 1/4" X 42 3/4" X = YE O=NO NOTE: 1. ALLOW 30" CLEARANCE TO ERVICE IDE OF UNIT, 48" ABOVE UNIT, 6" ON ONE IDE, 12" ON REMAINING IDE, AND 24" BETWEEN UNIT FOR PROPER AIRFLOW / MINIMUM OUTDOOR F, MAX. OPERATING 125 AMBIENT IN COOLING MODE I ERIE DEIGNATION I THE 14TH POITION OF THE UNIT MODEL NUMBER. 4. CENTER OF GRAVITY. A Q. AIR IN AIR DICHARGE G M 5. ALL DIMENION ARE IN "INCHE" UNLE NOTED. AIR DICHARGE B FIELD CONTROL UPPLY CONN. 7/8" HOLE FIELD POWER UPPLY CONN. 7/8" HOLE WITH 1 1/8" KNOCKOUT AIR IN N F AIR IN 3/8" LIQUID LINE CONN. C 31/2" D VAPOR LINE CONN. 17/8" P 3 13/16" L 11/8" K AIR IN E MINIMUM UNIT IZE MOUNTING PAD DIMENION - 26" X 26" /2" X 31 1/2" 24,30,36,42,48,60 35" X 35" 3/8" TIEDOWN KNOCKOUT (2) PLACE 9

10 DIMENION - I UNIT ERIE ELECTRICAL CHARACTERITIC A B C D E F G K L M N P OPERATING WEIGHT (Kgs) HIPPING WEIGHT (Kgs) HIPPING DIMENION (L x W x H) 018 A X O O O X X A X O O O X X A X O O O X X A X O O O X X A X O O O X X A X O O O X X A X O O O X X X = YE O=NO / C, MAX. 52 A Q. AIR IN AIR DICHARGE AIR DICHARGE G M B FIELD CONTROL UPPLY CONN HOLE FIELD POWER UPPLY CONN HOLE WITH KNOCKOUT AIR IN N F AIR IN C 88.9 D VAPOR LINE CONN P 96.8 L 28.6 K AIR IN E MINIMUM UNIT IZE MOUNTING PAD DIMENION X X ,30,36,42,48, X TIEDOWN KNOCKOUT (2) PLACE 10

11 BALANCE POINT WORKHEET BUILDING HEAT LO, UNIT INTEGRATED HEATING CAPACITY, MBTUH kw NA060 FX4DNF061 NA048 FX4DNF049 NA042 FX4DNF043 NA036 FX4DNF037 NA030 FX4DNF031 NA024 FX4DNF025 NA018 FX4DNF019 BAED ON INDOOR ENT. AIR AT 70 ºF (21.1) AND AT RATED (-23) 0 (-17.78) 10 (-12.22) 20 (-6.67) 30 (-1.11) 40 (4.44) 50 (10) 60 (15.56) 70 (21.11) 80 (26.67) OUTDOOR TEMPERATURE, ºF (ºC) 11

12 CLEARANCE Clearances (various examples) Wall Wall 24 ervice 6 (152.4 mm) 12 (304.8) 24 (609.6) ervice Wall 6 (152.4) 12 (304.8) 12 (304.8) 12 (304.8) Wall 24 (609.6) ervice 24 (609.6) ervice 24 (609.6) ervice A (609.6) 24 (609.6) 24 (609.6) Note: Numbers in ( ) = mm IMPORTANT: When installing multiple units in an alcove, roof well, or partially enclosed area, ensure there is adequate ventilation to prevent re -circulation of discharge air. 12

13 TETED AHRI COMBINATION RATING* NOTE: Ratings contained in this document are subject to change at any time. For AHRI ratings certificates, please refer to the AHRI directory Additional ratings and system combinations can be accessed via the Bryant database at: Equipment performance calculator can be accessed at: Model Number Coil Model Number High Temp Low Temp Furnace Model Cooling EER EER HPF Number Capacity E H ECOP HCOP Capacity Capacity NA018****A FX4DNF019 17, , , NA024****A FX4DNF025 24, , , NA030****A FX4DN(B,F)031 28, , , NA036****A FX4DN(B,F)037 34, , , NA042****A FX4DN(B,F)043 41, , , NA048****A FX4DN(B,F)049 47, , , NA060****A FX4DN(B,F)061 57, , , * AHRI = Air Conditioning, Heating & Refrigeration Institute Ratings are net values reflecting the effects of circulating fan heat. upplemental electric heat is not included. Ratings are based on: Cooling tandard: 80_F (27_C) db 67_F (19_C) wb indoor entering air temperature and 95_F (35_C) db air entering outdoor unit. High---Temp Heating tandard: 70_F (21_C) db indoor entering air temperature and 47_F (8_C) db 43 F (6_C) wb air entering outdoor unit. Low---Temp Heating tandard: 70_F (21_C) db indoor entering air temperature and 17_F ( ---8_C) db 15 F ( ---9_C) wb air entering outdoor unit. COP Coefficient of Performance EER Energy Efficiency Ratio HPF eating easonal Performance Factor EER easonal Energy Efficiency Ratio 13

14 DETAILED COOLING CAPACITIE # EVAPORATOR AIR EWB CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens NA018****A Outdoor ection With FX4DNF019 Indoor ection 72 (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) EVAPORATOR AIR EWB eenoteonpg.17 CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens NA024****A Outdoor ection With FX4DNF025 Indoor ection 72 (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9)

15 DETAILED COOLING CAPACITIE # CONTINUED EVAPORATOR AIR EWB CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens NA030****A Outdoor ection With FX4DNF031 Indoor ection 72 (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) EVAPORATOR AIR EWB eenoteonpg.17 CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens NA036****A Outdoor ection With FX4DNF037 Indoor ection 72 (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9)

16 DETAILED COOLING CAPACITIE # CONTINUED EVAPORATOR AIR EWB CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens NA042****A Outdoor ection With FX4DNF043 Indoor ection 72 (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) EVAPORATOR AIR EWB eenoteonpg.17 CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens NA048****A Outdoor ection With FX4DNF049 Indoor ection 72 (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9)

17 DETAILED COOLING CAPACITIE # CONTINUED EVAPORATOR AIR EWB CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens NA060****A Outdoor ection With FX4DNF061 Indoor ection 72 (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) (22.2) (19.4) (17.2) (16.7) (13.9) { Total and sensible capacities are net capacities. Blower motor heat has been subtracted. } ensible capacities shown are based on 80_F (27_C) entering air at the indoor coil. For sensible capacities at other than 80_F (27_C), deduct 835 Btuh (245 kw) per 1000 (480 L/) of indoor coil air for each degree below 80_F (27_C), or add 835 Btuh (245 kw) per 1000 (480 L/) of indoor coil air per degree above 80_F (27_C). # Detailed cooling capacities are based on indoor and outdoor unit at the same elevation per AHRI standard 210/ If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. 17

18 HEAT PUMP HEATING PERFORMANCE INDOOR AIR OUTDOOR COIL ENTERING AIR TEMPERATURE F ( C) ( ) 7 ( ) 17 (---8.3) 27 (---2.8) 37 (2.8) 47 (8.3) 57 (13.9) 67 (19.4) EDB 65 (18.3) 70 (21.1) 75 (23.9) Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* NA018****A Outdoor ection With FX4DNF019 Indoor ection INDOOR AIR OUTDOOR COIL ENTERING AIR TEMPERATURE F ( C) ( ) 7 ( ) 17 (---8.3) 27 (---2.8) 37 (2.8) 47 (8.3) 57 (13.9) 67 (19.4) EDB Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* NA024****A Outdoor ection With FX4DNF025 Indoor ection (18.3) (21.1) (23.9) eenoteonpg.21 18

19 HEAT PUMP HEATING PERFORMANCE CONTINUED INDOOR AIR OUTDOOR COIL ENTERING AIR TEMPERATURE F ( C) ( ) 7 ( ) 17 (---8.3) 27 (---2.8) 37 (2.8) 47 (8.3) 57 (13.9) 67 (19.4) EDB 65 (18.3) 70 (21.1) 75 (23.9) Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* NA030****A Outdoor ection With FX4DNF031 Indoor ection INDOOR AIR OUTDOOR COIL ENTERING AIR TEMPERATURE F ( C) ( ) 7 ( ) 17 (---8.3) 27 (---2.8) 37 (2.8) 47 (8.3) 57 (13.9) 67 (19.4) EDB Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* NA036****A Outdoor ection With FX4DNF037 Indoor ection (18.3) (21.1) (23.9) eenoteonpg.21 19

20 HEAT PUMP HEATING PERFORMANCE CONTINUED INDOOR AIR OUTDOOR COIL ENTERING AIR TEMPERATURE F ( C) ( ) 7 ( ) 17 (---8.3) 27 (---2.8) 37 (2.8) 47 (8.3) 57 (13.9) 67 (19.4) EDB 65 (18.3) 70 (21.1) 75 (23.9) Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* NA042****A Outdoor ection With FX4DNF043 Indoor ection INDOOR AIR OUTDOOR COIL ENTERING AIR TEMPERATURE F ( C) ( ) 7 ( ) 17 (---8.3) 27 (---2.8) 37 (2.8) 47 (8.3) 57 (13.9) 67 (19.4) EDB Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* NA048****A Outdoor ection With FX4DNF049 Indoor ection (18.3) (21.1) (23.9) eenoteonpg.21 20

21 HEAT PUMP HEATING PERFORMANCE CONTINUED INDOOR AIR OUTDOOR COIL ENTERING AIR TEMPERATURE F ( C) ( ) 7 ( ) 17 (---8.3) 27 (---2.8) 37 (2.8) 47 (8.3) 57 (13.9) 67 (19.4) EDB 65 (18.3) 70 (21.1) 75 (23.9) Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* Total Integ* NA060****A Outdoor ection With FX4DNF061 Indoor ection NOTE: When the required data falls between the published data, interpolation may be performed. Extrapolation is not an acceptable practice. * The Btuh heating capacity values shown are net integrated values from which the defrost effect has been subtracted. The Btuh heating from supplement heaters should be added to those values to obtain total system capacity. { The kw values include the compressor, outdoor fan motor, and indoor blower motor. The kw from supplement heaters should be added to these values to obtain total system kilowatts. EDB EnteringDryBulb 21