Prepared especially for:

Transcription

1 For vended and commercial homestyle laundry equipment facilities in apartments, residence halls, condominiums, cooperatives, hotels, motels, military installations, campgrounds, RV parks, senior citizen residences, truck stops and marinas. Prepared especially for: Building owners, college housing directors, military procurement officers, management companies, architects, engineers, specification writers, contractors and builders.

2

3 Table of Contents page 1 Exceptional Choices from Speed Queen Basics in Establishing a Laundry Laundry Room Layouts Equipment Sizing Ratios Suggested Floor Plans Installation Suggestions/Equipment Specifications Product Options & Dimensions Products Our 90 year reputation for quality products with innovative technology is supported by our position as North America's largest manufacturer of commercial laundry equipment. Systems Our customized systems for coin or smart-card vending options include NetMaster TM and CardMate Plus TM software with a NetMaster Control TM for computerized programming and data retrieval. Services A national network of Speed Queen Route Operators is in place to provide valuable information about Speed Queen s exceptional choices of laundry products, systems and service. Sales, service and warranty is available from this national network of authorized Speed Queen Route Operators. When equipping a laundry room the decisions seem endless. With Speed Queen's combination of quality products, innovative systems, and a dependable Customer One Service program, you can be confident that Speed Queen can meet all your laundry needs and you'll be happy with the results. For information and solutions to questions about multi-housing laundry equipment, visit our website at or call or look in the yellow pages for a Speed Queen Route Operator nearest you!

4 Exceptional Choices From page 2 The NetMaster TM System The NetMaster TM Model Line The NetMaster CardMate TM Model Line This system allows route operators to quickly and easily program and reprogram machines on-site or remotely through a networked PC. This maximizes business control, on-site security and expedites promotional activities. MANAGEMENT CONTROL Micro-WandIIIE TM With the state of the art NetMaster System, you can have one central location monitor various laundry locations through network usage. The hand-held Micro- Wand IIIE with infra-red technology still allows easy on-site programming and data retrieval. The possibilities are endless for professional laundry room management. AUDIT CONTROL NetMaster TM Software for Windows Speed Queen NetMaster TM laundry equipment records the total number of cycles, special vend options, plus the time and date of collections, coin vault openings, service door openings, power failure and more. It calculates and stores data automatically to keep you informed of day-to-day laundry room activities. Data can be retrieved with the Micro-Wand IIIE TM, or remotely through a networked system from anywhere in the world! Then by downloading the information into the NetMaster TM Software, input actual collection information by location to generate detailed, reader-friendly accountability reports. Speed Queen s NetMaster TM model line incorporates numerous options and customer convenience features that make the washing and drying of laundry loads a breeze. The NetMaster Control TM () has features such as: Vend Price Display which informs customers of the amount of money required to operate equipment, then counts down price as quarters are inserted. Touch Pad Control offers a tremendous range of options. An LED light with a sound annunciator signals to the user that their selection has been made. The user then pushes the green start pad after inserting the card or proper amount of coins. Cycle Count Down visually displays total length of cycle, then counts down the cycle time on the washer and dryer. Bright, Easy-to-Read Status Lights that take customers step-by-step through each phase of the wash or dry cycle. DROP COIN VALIDATOR automatically verifies magnetic content, coin size and weight, and records time, date and total amount collected into memory for future data retrieval. Speed Queen's CardMate TM model line with factory-installed smart-card reader controls offer convenient cashless operation for your customers, and increased accountability and profitability for property managers. The CardMate TM models include unique smart-card micro chip technology. This prepaid card is used to activate laundry equipment. To receive a card or to add value, a convenient card service center is available. SIMPLIFIED INSTALLATION CardMate TM washers and dryers can be installed by Speed Queen route operators quickly and easily, so you can enjoy the benefits of card-operated equipment in no time. REMAINING BALANCE DISPLAY Besides the ease and flexibility of installation, the CardMate TM model line features NetMaster Control TM () that informs customers everything they need to know about machine status at a glance. Residents can at any time check their remaining card balance without starting the machine. This helps speed up machine turnover and increase profitability. When used in conjunction with the NetMaster TM System you can retrieve information on machine usage to increase efficiencies in managing your laundry room.

5 I L page 3 The Micro-Display TM Control Model Line Speed Queen s Micro-Display Control (MDC) is a streamline version of the NetMaster control. It offers the features most important to the residents with less programming options. The MDC has features such as: Coin Countdown Start which informs customers of the amount of money required to operate equipment, then counts down price as quarters or card are inserted. Once the machine has started, the control counts down remaining cycle time. Touch Pad Control has convenient touch pads for accurate selection of cycles and a dedicated push-to-start pad to initiate cycle. Audible Sound Indicator and LED lights indicate when a change has been made keeping customers aware of cycle status and coin validation. Bright, Easy-to-Read Status Lights that take customers step-by-step through each phase of the wash or dry cycle. COIN OR CARD-OP OPTIONS Available with drop coin acceptor for coin, or card-operated models for interfacing with OEM card reader systems for cashless operation. MDC The Electromechanical Model Line Speed Queen offers the most complete range of coin-operated and manually operated laundry products; topload and frontload washers, single and stack dryers, tumblers and washer-extractors, for the variety of needs in multi-housing dwellings. With features such as water and energy efficient designs, quality internal components and high security systems, multi-housing owners can depend on Speed Queen equipment to give them the advantage on such issues as energy conservation, equipment breakdowns and vandalism. These electromechanical machines are equipped with one of the following activation options: Depositing coins into a coin slide Depressing the push-to-start knob PUSH TO START It's your choice. Customize your laundry room to fit your needs. E B R T Y IN GOD WE TRUST The Commercial Homestyle Model Line Speed Queen's commercial quality and expertise is present in these non-vended homestyle model washers and dryers. Washer Control Panel Dryer Control Panel Convenient features such as 3 wash/rinse temperatures, 6 drying cycles, 3 fabric types, and selectable water fill level gives the user exceptional choices for receiving the best laundering possible.

6 page 4 Basics In Establishing A Laundry WHERE CAN COMMON LAUN- DRY ROOMS BE ESTABLISHED? Multi-housing residences in either low or high rise apartment complexes, residence halls, condominiums, military housing, college residence halls, guest services and in-unit apartments. WHY VENDED EQUIPMENT? The high cost of operating multihousing residential facilities makes the common laundry area particularly attractive. Depending upon the arrangement made with a laundry service company commonly called a Route Operator which supplies the equipment the cost of operating a laundry can be completely offset and can, under certain arrangements with the Route Operator, return a portion of the income obtained from the laundry equipment to an owner or manager of the housing facility. WHO INSTALLS & MAINTAINS THE EQUIPMENT? The building management can retain the services of a Speed Queen Route Operator. In this arrangement the Route Operator provides, installs and maintains the equipment in the facility at his/her expense. The Route Operator will, under certain arrangements, return a percentage of the equipment income to management. Lease-purchase arrangements are sometimes available through the Route Operator. WHERE TO FIND A SPEED QUEEN ROUTE OPERATOR? You can contact a Speed Queen Route Operator nearest you by using our website locator at or by checking the classified pages of your telephone directory under "Washers and Dryers/Coin-Operated" or call for information. Look for the Speed Queen name. WHAT ABOUT ENERGY CONSUMPTION? Speed Queen equipment has been designed for energy conservation. All Speed Queen frontload washers have qualified for the Energy Star rating by exceeding the Department of Energy Modified Energy Factor (MEF) standard. Our heavy duty commercial washers are available in vertical (toploading) and horizontal axis frontload models. These washers have special energy settings on some models which lowers water consumption and are equipped with cold water rinse to reduce hot water costs. These washers are designed with industry-leading high speed extract speeds of 710 and 1000 RPMs on topload and frontload washers. This maximizes moisture removal for faster drying and less expense to the property. Speed Queen dryers are efficient in fast drying and low in energy consumption. Check with a Speed Queen authorized Route Operator to find out if your utility consumption is as low as it can be. They can perform a Cost Calculator Analysis for you! HOW MUCH EQUIPMENT? In planning and designing a laundry facility for multi-housing use, it is important to keep in mind the characteristics of the people who will occupy the building. The type of multi-housing building will dictate whether the laundry equipment should be concentrated into one centralized area or smaller rooms spread throughout the property. It is important that the room(s) are planned with proper facilities for electric and gas hook-ups, water supply and drainage, as well as proper makeup air and dryer ventilation. The following pages present our suggestions for the product types and amount of Speed Queen equipment required for sizing multi-housing properties. Specific situations demand the expertise of a qualified Route Operator so the proper equipment in the proper mix is provided for the residents convenience.

7 Laundry Room Layouts page 5 CENTRALIZED LAUNDRY ROOMS (High-Rise Buildings with apartments, condos, coops) The equipment can be concentrated in a convenient central area located in the building. The larger space requirement can expand the services to residents with variable sized washer-extractors with bigger load capacities, expanded vending concessions, folding tables, and comfortable waiting areas similar to on-street coin laundries. For high-rise buildings with a central laundry room, one washer and dryer set is recommended for every 20 living units. DE-CENTRALIZED LAUNDRY ROOMS (High-Rise or Low Rise Buildings with apartments, condos, coops) For planned communities, de-centralized laundry rooms or small laundry areas with matching washers and dryers are the most common. Usually these establishments are amenity oriented, offering folding tables and vending machines for the tenant's convenience. One washer and one dryer is recommended for every 8 to 12 living units. ON-FLOOR LAUNDRY ROOMS (Low Rise or Garden-Style Buildings) For garden apartments, matching washer and dryer pairs are the most customer convenient layout. One washer and one dryer is recommended for every 8 to 12 apartment units.

8 Suggested Floor Laundry Plans Room Layouts page 6 MILITARY HOUSING Centralized laundry rooms with commercial top or frontload washers and matching dryers for military personnel. Non-metered (free start) equipment is usually required by military. One washer and one dryer is recommended for every 20 military personnel. COLLEGE RESIDENCE HALLS Centralized laundry rooms are conveniently located in residence halls with top or frontload washers and matching dryers. For student residence halls one washer and one dryer is recommended for every 30 to 40 students. IN-APARTMENT For ultimate customer convenience, placement of laundry units is within the apartment, with top or frontload washer and matching dryer. One washer and one dryer is recommended per unit.

9 Equipment Sizing Ratios page 7 ONE SET is defined as 1 ea. topload or frontload washer paired with 1 ea. dryer pocket, or 1 stacked washer/dryer If multiple sets are needed use the following examples as your guide: EXAMPLES of Multiple Sets: 2 ea. topload/frontload washers...with...1 ea. stacked dryer (= 2 dryer pockets) 2 ea. topload/frontload washers...with...2 ea. single load dryers (= 2 dryer pockets) 2 ea. topload/frontload washers...with...1 ea. tumbler dryer (1 tumbler pocket = 2 dryer pockets) ONE washer/dryer set is recommended for the following: PROPERTY TYPE NO. OF LIVING UNITS High-Rise Building to 25 living units Low-Rise or Garden Building to 12 living units Coops, Condominiums to 12 living units Senior Citizen Centers residents Military Housing military personnel College Residence Halls to 40 students Guest Services rooms In-Apartment set per unit Suggested Floor Plans HIGH-RISE BUILDINGS (central laundry room) TYPICAL 400-UNIT HIGH-RISE APARTMENT BUILDING ACTIVATION: Smart-Card CONTROL: NetMaster Control with touch pad MODEL LINE: CardMate TM EQUIPMENT: Topload and Frontload Washers and Tumblers

10 I L E B page 8 Suggested Floor Plans HIGH-RISE CONDOMINIUM (decentralized laundry) TYPICAL 120-UNIT MULTIPLE LEVEL HOUSING FACILITY ACTIVATION: Coin Drop CONTROL: NetMaster Control with touch pad MODEL LINE: NetMaster TM EQUIPMENT: Horizon Stacked Washers/Dryers LOW-RISE OR GARDEN BUILDINGS TYPICAL 20-UNIT MULTIPLE BEDROOM ACTIVATION: Coin Slide CONTROL: Rotary Switches MODEL LINE: Electromechanical EQUIPMENT: Topload Washers and Single Load Dryers R T Y IN GOD WE TRUST

11 Suggested Floor Plans page 9 RESIDENCE HALLS (central laundry room*) TYPICAL CENTRAL LAUNDRY ROOM ACTIVATION: Coin Drop or On-Line Debit Card Reader CONTROL: NetMaster Control with touch pad MODEL LINE: NetMaster EQUIPMENT: Horizon Frontload & Topload Washers* with Stack Dryers *Front control washers and dryers are ADA Compliant NetMaster Wash Alert System Web site call back technology of machine availability for residence laundry rooms Data Flow

12 I L E B page 10 Suggested Floor Plans MILITARY HOUSING (central laundry room- BEQ s or BOQ s) TYPICAL BARRACK FACILITY ACTIVATION: Push/Pull Start Knob CONTROL: Rotary MODEL LINE: Commercial/Homestyle EQUIPMENT: Topload Washers and Single Load Dryers GUEST SERVICES (Hotels, motels, campgrounds, marinas, truck stops TYPICAL GUEST SERVICE FOR VENDED LAUNDRY-HOTEL/MOTEL ACTIVATION: Coin Slide CONTROL: Rotary MODEL LINE: Electromechanical EQUIPMENT: Topload Washers and Single Load Dryers R T Y IN GOD WE TRUST

13 Suggested Floor Plans page 11 IN-UNIT APARTMENT/CONDO WASHER AND DRYER TYPICAL IN-APARTMENT SIDE BY SIDE LAUNDRY FACILITY ACTIVATION: Push/Pull Start Knob CONTROL: Rotary MODEL LINE: Commercial/Homestyle EQUIPMENT: Top or Frontload Washer and Single Load Dryer ADA Compliance (American Disabilities Act) Speed Queen s Front Control & Front Loading Laundry Equipment Makes the Grade Your students have enough on their minds without having to think about how to do their laundry. Speed Queen s Horizon front control and front loading side-by-side washer and dryer models are designed for front access so all controls and mechanisms, including doors, lint screens, detergent and bleach compartments comply with ANSI/CABO A reach standards for unobstructed front and side access. ADA unobstructed front or side reach requirements: Control Panel 48 Max Height Loading Door (from floor) 15 Min. Height Speed Queen Horizon Washer and Dryer measure up to ADA: Control Panel 40 Height Loading Door (from floor) 15.5 Height If you are concerned about your laundry room complying with ADA regulations, stop worrying. Purchase Speed Queen s Horizon washer and dryer to meet the needs of ADA, but most importantly the needs of your students or residents.

14 page 12 Installation Suggestions & Equipment Specifications GENERAL ROOM INFORMATION 1. Determine the size of the laundry room by allowing a minimum of 25 square feet (2.25 m 2 ) per machine. 2. At least one floor drain should be provided in each laundry. 3. Wash tubs not required. However, if they are installed, provide adequate space for them. Such space shall be in addition to that recommended for each machine. 4. Locate dryers on outside walls since long ducts increase installation cost and are less effective for proper venting. 5. For proper operation, it is important to locate the dryer in an area that has an ample amount of make-up air to replace the amount exhausted by the dryer. Energy efficient multi-housing facilities with low air infiltration rates should be equipped with an air exchanger that can accommodate on-demand make-up air. These devices can be obtained through your building contractor or building material suppliers. 6. Tumbler make-up air must be brought into the room to replace air being exhausted. Tumblers require fresh outside make-up air. Minimum requirement: Single Tumblers sq. in. opening to the outside. Stack Tumblers sq. in. opening to the outside. 7. Provide sufficient lighting, preferably fluorescent. EQUIPMENT SIZING RECOMMENDATION One dryer for each single load (topload or frontload) washer is the recommended product balance. One stacked dryer, or one 25-lb. RouteMaster TM tumbler will accommodate two topload or frontload washers. A stacked tumbler will accommodate for 4 topload washers. Topload and Frontload Washers Electrical Requirements 1. Each washer is designed to be operated on an individual threewire grounded, 120 volt, 60 Hz electrical circuit protected by a 15 or 20 amp fuse, equivalent fusetron or circuit breaker. No. 12 wire recommended for electrical connection or as required by local codes. 2. All receptacles shall be equipped for a three prong grounded plug. Plumbing Requirements 1. Water supply faucets must fit standard 3/4" (19.1 mm) female hose couplings. 2. Hot water facilities should have the capability of maintaining a constant water temperature of between 120º-140ºF for frontload washers and 140º-150ºF for topload washers. 3. Maintain cold water temperature at not less than 35ºF (1.6ºC). 4. Washer will operate under a variety of sufficient water pressure conditions; however, a constant water pressure of 30 psi must be maintained. 5. Drain each washer into a minimum 2" (50.8 mm) diameter by 3' tall cast iron, PVC or copper standpipe. Water Usage Charts for Topload and Frontload Washers Water Usage Chart - Topload MDC - Water Saver Total Water Cycle /Temp. Hot Cold Consumption Normal/Hot Gallons Normal/Warm Gallons Perm. Press/Warm Gallons Delicate/Cold Gallons DOE clothes washer test standards appendix J1 for a 10.9 lb load. Water Usage Chart - Horizon MDC Total Water Cycle /Temp. Hot Cold Consumption Normal/Hot Gallons Normal/Warm Gallons Perm. Press/Warm Gallons Delicate/Cold Gallons DOE clothes washer test standards appendix J1 for a 11.7 lb load.

15 Installation Suggestions & Equipment Specifications page 13 Single and Stack Dryers (Gas and Electric models) Electrical Requirements 1. (Electric Models) Provide separate circuits from the main panel to each dryer. Each dryer has its own terminal block that must be connected to a separate branch three-wire, 120/240 or 120/208 volt, 60 Hz, single phase circuit using at least No. 10 copper wire and fused at 30 amps; a grounded neutral wire must be provided. Do not connect dryers to 110, 115 or 120 volt circuits. 2. (Electric Models) If branch circuit to electric dryers is 15 ft. (4572 mm) or less in length, use UL approved No. 10 copper wire, or as required by local codes. If over 15 ft. (4572 mm), use No. 8 UL approved copper wire, or as required by local codes. 3. (Gas Models) Each gas dryer is designed to be operated on an individual three-wire grounded 120 volt, 60 Hz. electrical circuit protected by a 15 amp fuse, equivalent fusetron or circuit breaker. (See specifications) 4. (Gas Models) Plug each dryer's power cord into a grounded 3-slot wall receptacle on a separate NEW STAINLESS STEEL FLEXIBLE CONNECTOR USE ONLY IF ALLOWED BY LOCAL CODES (Use Design A.G.A. Certified Connector) 3/8" NPT GAS CONNECTION BLACK IRON PIPE Shorter than 20' (6.1 m) - use 3/8" pipe Longer than 20' (6.1 m) - use 1/2" pipe Figure 1 circuit. Do not operate other appliances on the same circuit when dryer is operating. 5. (Electric and Gas Models) All dryer installations should conform to the latest edition of the National Electrical Code, NFPA 70, and such local requirements as might apply. Gas Requirements (also see Figure 1 below) 1. The gas dryer installation must conform with the latest edition of American National Standard Z223.1 (NFPA 54) National Fuel Gas Code. 2. Size of main gas supply unit will depend on number of dryer units connected. Consult local gas utility. 3. Where bottled gas (L.P.) is used, follow the specifications of the local gas company. A special conversion kit for L.P. is required. Consult your Speed Queen Route Operator for details. Venting Requirements for Single and Multi-Dryer Installations 1. The gas dryer installation should comply with the latest edition of the National Fuel Gas Code, Z223.1 (NFPA 54). 1/8" NPT PIPE PLUG (For checking inlet gas pressure) EQUIPMENT SHUT-OFF VALVE Installed within 6' (1.8 m) of dryer D233IE2E 2. A 4" (102 mm) vent hood with a damper (for each dryer) should be placed in the wall behind the dryer while the building is under construction. 3. Exhaust pipe must be 4" (102 mm) in diameter having no obstructions. Rigid or flexible metal pipe must be used. Weather Hood Type Recommended Number of 90º Elbows D673I Maximum length of 4" (102 mm) diameter rigid metal duct Weather Hood Type Use only for short run installs Number of 90º Elbows 4 (10.2 cm) 0 65 ft (19.8 m) 1 55 ft (16.8 m) 2 47 ft (14.3 m) 3 36 ft (11.0 m) 4 28 ft (8.5 m) 0 45 ft (13.7 m) 1 35 ft (10.7 m) 2 30 ft (9.1 m) 3 25 ft (7.6 m) 4 20 ft (6.1 m) 2-1/2" (6.35 cm) D011IE2E 4 (10.2 cm) Maximum length of 4" (102 mm) diameter rigid metal duct 0 55 ft (16.8 m) 1 47 ft (14.3 m) 2 41 ft (12.5 m) 3 30 ft (9.1 m) 4 22 ft (6.7 m) 0 35 ft (10.7 m) 1 27 ft (8.2 m) 2 21 ft (6.4 m) 3 17 ft (5.2 m) 4 15 ft (4.5 m)

16 Installation Suggestions & Equipment Specifications page 14 DO NOT use flexible plastic or thin foil ducting as it will greatly reduce the dryer's performance. Outer end of exhaust pipe must have weather hood installed at least 12" (305 mm) above ground. Always keep exhaust duct as short as possible. 4. Gas dryers can be vented from the right side, back, or bottom (except upper unit of stack dryer). Dryer can be installed flush to the wall at side and back. Electric dryers can be routed from left side as well. 5. The exhaust duct should not be built into the wall. If laundries are distributed in multi-story buildings, the duct size at the first floor should be at least 4" (102 mm) and should be increased in size 1" (25.4 mm) per floor to a maximum of 12" (305 mm). For the installation of several dryers where a main collector duct is used, see illustration for proper angle of air flow. Dryer exhaust duct should enter main duct at an angle of no more than 30º pointing in the direction of the airflow. Ducts entering the main duct from opposite sides should be staggered so as not to oppose each other. Provisions should be made for periodic lint removal and cleaning of the main collector duct. 6. If several dryers are exhausted into a main collector duct, it is essential that ductwork be adequate in size and properly constructed for efficient operation. Provisions for make-up air must be provided. Each dryer exhausts approximately 220 cubic feet* (6.1 m 3 ) of air per minute. * Measured at point of exit from the dryer. 7. The main collector duct should be sized according to specifications Duct Station Minimum Diameter of Collector Duct A 4 inches (102 mm) B 8 inches (203 mm) C 9 inches (229 mm) D 10 inches (254 mm) E 11 inches (279 mm) F 12 inches (305 mm) G 13 inches (330 mm) H 14 inches (356 mm) I 15 inches (381 mm) J 15 inches (381 mm) K 16 inches (406 mm) NOTE: Main collector ducts should be equipped with an auxiliary fan that can maintain the duct airflow at a minimum of 1200 ft (366 m) per min. If you do not have a fan, clean the main collector duct at least twice a year presented in the chart on the right. The outside of the main duct should have a weather hood (with hinged damper) installed to prevent passage of weather elements, insects, dust and dirt into the dryer. 8. Each dryer should have a back draft damper kit, part number A B C D E F G H I J K 1 NOTE: Where the exhaust duct pierces a combustible wall or ceiling, the opening must be sized per local codes. 2 Wall HORIZONTAL EXHAUST INSTALLATION 1 AIR FLOW EXHAUST AIR FLOW MAXIMUM LENGTH OF DUCT 30 feet (9.1) 3 2" (5 cm) Minimum or Clearance per local codes 4 No Screen or Cap 2 Clean Out Cover - Inspect Monthly Electrical Requirements Electric Dryer and Stacked Dryer Canada Gas Dryer and Stacked Dryer Canada 1 2 EXHAUST OUTLET " (61cm) MINIMUM CLEARANCE TO ROOF/GROUND CONNECT TO DRYER 24" (61cm) MINIMUM CLEARANCE TO ROOF/GROUND D686I 5 VERTICAL EXHAUST INSTALLATION 1 Roof 2 No Screen or Cap 3 Wall 4 2" (5 cm) Minimum 5 NOTE: Where the exhaust duct pierces a combustible wall or ceiling, the opening must be sized per local codes. 60 Hz watt element, 120/240V or 4750 watt element, 120/208V, 3-wire, 1 phase, 30 amp. 60Hz. 5,000 watt element, 120/240 or 120/208V, 4-wire, 1 phase, 30 amp on dryer; 60 amp on stacked dryer. 60 Hz. AC, 120V, grounded 3-wire, 1 phase, 15 amp. 60 Hz. AC, 120V, grounded 3-wire, 1 phase 15 amp on dryer; 30 amp on stacked dryer. 3 4 D753I

17 Installation Suggestions & Equipment Specifications page lb., 30 lb. & 35 lb.single Tumbler 30 lb. Stacked Tumbler Electrical Requirements 1. Provide separate circuits from the main panel to each tumbler. The 120 volt, 60 hertz, single phase units require an individual threewire, grounded, 120 volt, 60 Hz electrical circuit protected by a 15 amp fusetron or circuit breaker. The 208 volt or 240 volt, 60 Hz, single phase units require a threewire plus ground circuit (two hot leads, a neutral and a ground). Each circuit must be protected with a two-pole, 10 amp circuit breaker. 2. All tumbler units must be grounded in accordance with the latest edition of the National Electrical Code, NFPA 70, and local codes and ordinances. Gas Requirements 1. Install a 1-1/2" (38.1 mm) main gas line for the laundry room for up to 10 tumblers. 2. Install a 1/2" (12.7 mm) gas line on the wall for connection to the back of the dryer. Terminate it with a 1/2" (12.7 mm) T, 6" (152.4 mm) drip leg and 1/2" (12.7 mm) gas cock. Venting Requirements 1. Locate where least exhaust piping and elbows will be required. Use sweep elbows. The exhaust should be directed upward. 2. All duct work must be adequate in size. See ducting chart below. 3. Provide cleanout and inspection doors in duct. All electrical and plumbing installations must conform to local and national codes. WALL CLEARANCE PER LOCAL CODES NO SCREEN OR CAP AIR OUT Electrical Requirements 1. Provide separate circuits from the main panel to each tumbler. There is only ONE electrical connection to the stacked tumbler upper pocket junction box. The 120 volt, 60 hertz, single phase units require an individual threewire, grounded, 120 volt, electrical circuit protected by a 30 amp fusetron or circuit breaker. The 208 volt or 240 volt, 60 hertz, single phase units require a threewire plus ground circuit (two hot leads, a neutral and a ground). Each circuit must be protected with a two pole, 20 amp circuit breaker. 2. All stacked tumbler units must be grounded in accordance with the latest edition of the National Electrical Code, NFPA 70, and local codes and ordinances. Gas Requirements 1. Install a 1-1/2" (38.1 mm) main gas line for the laundry room for up to 10 tumblers. 2. Install a 3/4" (19.05 mm) gas line on the wall for connection to the back of the dryer. Terminate it with a 3/4" (19.05 mm) T, 6" (152.4 mm) drip leg and 3/4" (12.7 mm) gas cock. Venting Requirements 1. Locate where least exhaust piping and elbows will be required. NOTE: WHERE THE EXHAUST DUCT PIERCES A COMBUSTIBLE WALL OR CEILING. THE OPENING MUST BE SIZED PER LOCAL CODES. MINIMUM DIAMETER FOR MODELS 0220S, 0270S 23" 23" 21" 20" 19" 18" 16" 15" 13" 11" 9" 30" 29" 27" 26" 25" 23" 21" 19" 17" 15" 12" 9" MINIMUM DIAMETER FOR MODELS 0300D, 0350S INSPECTION OR CLEANOUT COVER 7" 45 Use sweep elbows. The exhaust should be directed upward. 2. All duct work must be adequate in size. See ducting chart below. 3. Provide cleanout and inspection doors in duct. All electrical and plumbing installations must conform to local and national codes. Electrical Requirements 25 lb. and 30 lb. Single Tumbler Canada Export Models Stacked Tumbler Canada Export Models 60 Hz. 120V, 1 phase 12.0 amps, 2-wire grounded circuit (L1, N, G). Requires 15 amp one-pole protection. 60 Hz V, 1 phase 6.7 amps, 3- wire grounded circuit (L1, N, L2, G). Requires 10 amp two-pole protection. Same as above 50 Hz. 240V, 1 phase, 24.0 amps, 2-wire grounded circuit (L1, L2, G). Requires 10 amp two-poleprotection. 60 Hz. 120V, 1 phase, 24.0 amps, 2-wire grounded circuit (L1, N, G). Requires 30 amp one-pole protection. 60 Hz V, 1 phase, 13.4 amps, 3-wire grounded circuit (L1, N, L2, G). Requires 20 amp two-pole protection. Same as above 50 Hz. 240V, 1 phase, 15 amps, 2-wire grounded circuit (L1, L2, G). Requires 20 amp two-pole protection. 60 Hz. 220V, 1 phase, 11.6 amps, 2-wire (plus ground) (L1, N, G). Requires 15 amp two-pole protection.

18 page 16 Product Options & Dimensions Wa s h e r s & D ry e r s MDC Topload Washer PUSH TO START Washer has 3/4" (1.87 cm) connection for water mixing valve. Two water inlet hoses supplied with washer. Drain hose is 5' (150 cm) long. One inch (2.5 cm) inside diameter. Power cord has threeprong U.L. approved plug for connection to a 30.5" (74.47 cm) 25.63" (65.09 cm) grounded three-wire, 120 volt, 60 Hz electrical circuit. 15 to 20 amp. Use at least No. 12 wire, heavier for long distances. C H 28.75" (73.02 cm) 43" ( cm) 35.88" (91.05 cm) 0.44" (11.11 cm) 26" (66.04 cm) 28" (71.12 cm) 51" ( cm) 44.75" ( cm) W553I Dimensions are with leveling legs. Stand pipe should be 36 high. MDC Horizon Frontload Washer Washer has 3/4" (1.87 cm) connection for water mixing valve. Two water inlet hoses supplied with washer. Drain hose is 4' (122 cm) long. One inch (2.5 cm) inside diameter. 17.5" (44.8 cm) 14.9" (37.9 cm) Power cord has threeprong U.L. approved 28" (71.1 cm) 2" (5.1 cm) plug for connection to a grounded three-wire, 120 volt, 60 Hz electrical circuit. 15 to 20 amp. Use at least No. 12 wire, heavier for long distances. 43" (109.2 cm) 31.1" (79 cm) 29.6" (75.1 cm) 26.9" (68.3 cm) H270I Dimensions are with leveling legs. Stand pipe should be 36 high. Small Dryer MDC PUSH TO START Electric dryer can be exhausted in any direction, vented out rear, either side or base. Gas models have 3-way venting: right side, back and base. Gas dryers available for natural gas, L.P. gas kit available. L.P. Gas Conversion Kit must be installed by the 23.5" (59.7 cm) 8.0" (20.3 cm) 28" (71.1 cm) 4.5" (11.4 cm).4" (1.02 cm) Manufacturer's Authorized Dealers, Distributors, or local service personnel. Power cord is furnished (120/60/1). 36" (91.4 cm) 43" (109.2 cm) 26.9" (88.3 cm) 15.4" (39.1 cm) 4.0" (10.2 cm) D611I Electric dryer models do not have power cord furnished (120/240/60/1 or 120/208/60/1).

19 Product Options & Dimensions Wa s h e r s & D ry e r s page 17 MDC Horizon Frontload Washer Washer has 3/4" (1.87 cm) connection for water mixing valve. Two water inlet hoses supplied with washer. Drain hose is 4' (122 cm) long. One inch (2.5 cm) inside diameter. 17.5" (44.8 cm) 14.3" (36.3 cm) Power cord has threeprong U.L. approved 28" (71.1 cm) 2" (5.1 cm) plug for connection to a grounded three-wire, 120 volt, 60 Hz electrical circuit. 15 to 20 amp. Use at least No. 12 wire, heavier for long distances. 2" (5.1 cm) 43" (109.2 cm) 31.1" (79 cm) 29.6" (75.1 cm) 26.9" (68.3 cm) H269I Dimensions are with leveling legs. Stand pipe should be 36 high. MDC Horizon Frontload Dryer Electric dryer can be exhausted in any direction, vented out rear, either side or base. Gas models have 3-way venting: right side, back and base. 2" (5.1 cm) 4.5" (11.4 cm) Gas dryers available for natural gas, L.P. gas kit 8.0" 15.4" (20.3 cm) available. L.P. Gas 0.4" 23.5" 28" (1.0 cm) 26.9" (59.7 cm) (71.1 cm) (68.3 cm) Conversion Kit must be installed by the Manufacturer's Authorized Dealers, Distributors, or local service personnel. Power cord is furnished (120/60/1). 43.0" (109.2 cm) (39.1 cm) 4.0" (10.2 cm) D825I Electric dryer does not have power cord furnished 120/240/60/1, (may be converted to 120/208/60/1). Stacked Dryer Gas Supply Connection: 3/8" (.937 cm) pipe provided at rear. Stacked dryer is delivered complete as one unit. Factory equipped for natural gas operation only. L.P. kits available. L.P. Gas Conversion Kit must be installed by the Manufacturer's Authorized Dealers, Distributors, or local service personnel. 7" (17.8 cm) 23.5" (59.7 cm) *With leveling legs turned into base. 8" (20.3 cm) 4.5" (11.4 cm) 28" (71.1 cm) *76.5" (194.3 cm) *44.8" (113.6 cm) 4" (10.2 cm) ELECTRIC MODELS 26.9" (68.3 cm) NOTE: Not all models have windows. 15.5" (39.4 cm) D786I MDC PUSH TO START Solid door or door with window available.

20 page 18 Product Options & Dimensions Wa s h e r s & D ry e r s MDC Horizon Stacked Washer/Dryer Gas Supply Connection: 3/8" (.937 cm) pipe provided at rear. Stacked washer/dryer is delivered complete as one unit. Factory equipped for natural gas operation only. L.P. kits available. L.P. Gas Conversion Kit must be installed by the Manufacturer's Authorized Dealers, Distributors, or local service personnel. 23.5" (59.7 cm) 5.25" (13.3 cm) 17.5" (44.8 cm) 14.3" (36.3 cm) 8.0" (20.3 cm) 28" (71.1 cm) 75" (190.5 cm) 44.1" (112 cm) 2" (5.1 cm) ELECTRIC DRYERS 26.9" (68.3 cm) 15.4" (39.1 cm) 29.6" (75.1 cm) 31.1" (79 cm) SWD440N *With leveling legs turned into the base. Commercial/Homestyle Washer Washer has 3/4" (1.87 cm) connection for water mixing valve. Two water inlet hoses supplied with washer. Drain hose is 5' (150 cm) long. One inch (2.5 cm) inside diameter. Power cord has three-prong U.L. approved plug for connection to a grounded three-wire, 120 volt, 60 Hz electrical circuit. 15 to 20 amp. Use at least No. 12 wire, heavier for long distances. 25.6" (65.0 cm) 29" (73.7 cm) 43" (109.2 cm) 36.4" (92.5 cm).4" (10.2 mm) 28" (71.1 cm) 26" (66.0 cm) 53" (134.6 cm) W507IE1A Dimensions are with leveling legs. Stand pipe should be as high as the washer top. Commercial/Homestyle Dryer Electric dryer can be exhausted in any direction, vented out rear, either side or base. Gas models have 3-way venting: right side, back and base. 8.0" (20.3 cm) 4.5" (11.4 cm) 0.4" Gas dryers available for natural (1.1 cm) 23.5" 28" 26.9" (59.7 cm) (71.1 cm) (68.3 cm) ELECTRIC DRYERS gas, L.P. gas kit *With leveling legs turned into the base. available. L.P. Gas Conversion Kit must be installed by the Manufacturer's Authorized Dealers, Distributors, or local service personnel. Power cord is furnished (120/60/1). 36" (91.4 cm) *43" (109.2 cm) 4" (10.2 cm) 15.4" (39.1 cm) D616I Electric dryer does not have power cord furnished (120/240/60/1).

21 Product Options & Dimensions H o m e s t y l e Wa s h e r s & D ry e r s page 19 Commercial/Homestyle Rear control Frontload Washer Washer has 3/4" (1.87 cm) connection for water mixing valve. Two water inlet hoses supplied with washer. Drain hose is 4' (122 cm) long. One inch (2.5 cm) inside diameter. Power cord has three-prong U.L. approved plug for connection to a grounded three-wire, 120 volt, 60 Hz electrical circuit. 15 to 20 amp. Use at least No. 12 wire, heavier for long distances. 17.5" (44.8 cm) 14.9" (37.9 cm) 28" (71.1 cm) Dimensions are with leveling legs. Stand pipe should be 36 high. 2" (5.1 cm) 36.6" (93 cm) 43" (109.2 cm) 31.1" (79 cm) 29.6" (75.1 cm) 26.9" (68.3 cm) H327I Commercial/Homestyle Front control Frontload Washer Washer has 3/4" (1.87 cm) connection for water mixing valve. Two water inlet hoses supplied with washer. Drain hose is 4' (122 cm) long. One inch (2.5 cm) inside diameter. 17.5" (44.8 cm) (37.9 cm) Power cord has three-prong U.L. approved plug for connection to a grounded threewire, 120 volt, 60 Hz electrical circuit. 15 to 20 amp. Use at least No. 12 wire, heavier for long distances. 28" (71.1 cm) Dimensions are with leveling legs. Stand pipe should be 36 high. 14.9" 41.2" (104.6 cm) 31.1" (79 cm) 29.6" (75.1 cm) 2" (5.1 cm) 26.9" (68.3 cm) FLW701N Commercial/Homestyle Front Control Dryer Electric dryer can be exhausted in any direction, vented out rear, either side or base. Gas models have 3-way venting: right side, back and base. Gas dryers available for natural gas, L.P. gas kit available. L.P. Gas Conversion Kit must be installed by the Manufacturer's Authorized Dealers, Distributors, or local service personnel. Power cord is furnished (120/60/1). 8.0" (20.3 cm) 23.5" 28" (59.7 cm) (71.1 cm) *With leveling legs turned into the base. 4.5" (11.4 cm) 0.4" (1.1 cm) ELECTRIC DRYERS *41.2" (104.6 cm) 15.4" (39.1 cm) 26.9" (68.3 cm) 4.0" (10.2 cm) DRY684N Electric dryer does not have power cord furnished (120/240/60/1).

22 page 20 Product Options & Dimensions Tu m b l e r s 25 lb. RouteMaster TM Handles 25 lb. (11kg) loads Energy saving gas models at 64,000 BTU/hr (18.8 kw) Electric and Steam models also available " (667 mm) 27.5" (699 cm) " (987 mm) " (1622 mm) 28" (711 mm) MDC 30/35 lb. Single Tumbler Handles 30 lb. (13.6 kg) or 35 lb. (15.9) loads Energy saving gas models at 73,000 BTU/hr (21.4 kw) Electric and Steam models also available. 30# 26.25" (667 mm) 35# 28" (711 mm) 27.5" (699 mm) " (1140 mm) " (1622 mm) 30# 28" (711 mm) 35# 31.5" (800 mm) MDC 30 lb. Stacked Tumbler Two full size 30 lb. (13.6 kg) pockets handle wash loads easily. Energy saving gas models at 73,000 BTU/hr (21.4 kw), per cylinder. Electric and Steam models also available. 10" (254 mm) 28" (711 mm) " (1040 mm) 31.5" (800 mm) 76.25" (1937 mm) MDC

23

24 The Right Choice For You AM