Vacuum Homogenizing Emulsification Machine. Instruction Manual

Transcription

1 Vacuum Homogenizing Emulsification Machine Instruction Manual 1

2 Please study this manual carefully before operating the machine, you are welcome to call our service department or check in our website for any inquires if you can not find any answer in this manual. Operators must be well trained by our authorized technician before operating the machine. The instruction manual is only supplied for your reference. We will not give further notice if any alternation is made. We reserve the right to vary this manual without prior notice. Please keep this manual carefully for future application. 2

3 Content Chapter 1. Main Structure... 4 Chapter 2. Working Principles....5 Chapter 3. Console Panel....6 Chapter 4. Working Flow Chart Chapter 5. Technical Parameters Chapter 6. Caution Chapter 7. Installation, Commissioning and Maintenance Chapter 8. Troubleshooting...10 Chapter 9. Electrical Schematics Chapter 10. Hydraulic Pressure Schematic Chart Chapter 11. Accompanying Documents...12 Chapter 12. Packaging and Shipping

4 Chapter 1 - Main Structure Structure statement YX-VME350L vacuum emulsifying unit is mainly consisted of main pot, grease pot, water pot, electric control panel, hydraulic system, vacuum system as well as the framework. The main pot includes isotropic stirring pot, the homogeneous unit and bidirectional mixing tools. 4

5 Chapter 2 - Working Principles The material is preheated and stirred in water and grease pot, and then will be leaded into the homogeneous pot in vacuum situation by the conveyor pipe. The material is stirred in the homogeneous pot. There is a Teflon scraper (scraper throughout to cater to pot shape, sweeping material sticking on the wall), unceasingly producing the new interface. The frame agitator and its reverse stirring leaf are operating by cutting, compressing and folding to stir and mix the materials which will flow down to the homogenizer. The high speed rotation of the rotor and stator will shear, shock the materials to be sheared in the shear cracks, producing the particles whose size is 200nm~2μm. The pelletizing, emulsification, mixing, homogenizing and dispersion of the materials can be done in a very short time. Since the homogeneous pot is under the vacuum state, the bubbles generated in the material during the mixing process will be siphoned quickly. After the homogenizing finished, raise the pot lid and press the dumping button and the materials will flow from the pot to the outer container. (Or you can open the valve at the bottom of the pot and pressure valve to discharge the mixed material directly). The heating temperature of the homogenous pot is displayed on the temperature controller located on the control panel. Homogeneous mixing and paddles stirring can be used separately or simultaneously. The isotropic frame and blend knife can be used at same time or separately. The homogenizing time can be changed according the material property and the time can be adjusted by customer via the control panel. Open the cleaning ball valve to clean the pot after work. 5

6 Chapter 3 - Console Panel Instruction: Operator can set proper speed, temperature, pressure and emulsifying time based on the production process Press down the hydraulic switch before pressing switch to raise/lower the crossbeam Please follow the flow chart in Part 4 to operate the system. 6

7 Chapter 4 Working Flow Chart Chapter 5 - Technical Parameters ITEM PARAMETER Power supply Emulsifying pot design capacity Working capacity Scraper stirring power 220V60Hz 380 L 300 L 2.2 Kw Stirring speed 0~85 rpm (Adjustable) Homogenizing power Electrical heating power 7.5 Kw 12kw Homogenizing rotating speed 0~2800 rpm (Adjustable) Water pot design capacity Water pot working capacity 280 L 220L 7

8 Stirring power Stirring speed Electrical heating power Overall machine size Main machine size 0.75KW 1400RPM 12kw (L W H)mm (L W H)mm Chapter 6 Caution 1. Since the homogenizing cutter has a very high speed when operating, don t run it in empty pot in case that parts overheat will effect the pot seal. 2. Ground wire should be connected to the ground to make sure of the electricity safety. 3. Homogenizer is running reversely when we look it from up view. Please jog to try to switch the motor when the motor is connected to electricity or after a long time without running. The stirring frame is turning reversely from the top view. Try to jog the agitator until it runs smoothly and then operate the homogenizer. 4. Joggle the machine to check any unusual behavior of the agitator and scraper before running the machine in full speed. Eliminate machine errors immediately if they are existing. 5. Make sure the pot lid, nozzle cover sealed properly before turning on the vacuum pump. 6. Shut off the vacuum ball valve before turning off the vacuum pump. 7. The vacuum pump can start operation when the homogenizing pot is well sealed. If the vacuum needs to be run under open air for special requirements, don t run the pump over 3 minutes. 8. Cut the power before any cleaning or maintenance of the machine 9. Do not put your hand into the pot when the equipment is running. 10. Stop the machine when unusual noise occurs. Check the machine thoroughly and fix the problem before re-starting the machine. Chapter7 - Installation, Commissioning and Maintenance 1. Connect the right power supply to the machine and make sure that the ground wire is connected to ground. Turn on the main power and the power indicator will light up.( Jog to try to switch the motor when the motor is connected to electricity or after a 8

9 long time without running. The stirring frame is turning reversely from the top view. Try to jog the agitator until it runs smoothly and then operate the homogenizer. ). 2. Connect all the hoses on the homogenizing pot in a right way (including overflow hoses, outlet hose and dumping hose). 3. Make sure the pot lid, nozzle cover sealed properly before turning on the vacuum pump before taking out the vacuum. Close all valve ports on the lid and open the vacuum valve on the lid. Then turn on the vacuum pump and turn it off when the air is taken out. Close the vacuum valve at the time. (Please refer to the flow chart for details) 4. Homogenizing cutting, scraper stirring: Turn on the homogenizing cutter and scraper frame after feeding the material into the isotropic pot. Joggle the motor and check the stirring scraper before start. If there is any errors, stop and machine solve the problems immediately before resetting. 5. The vacuum pump can start operation when the homogenizing pot is well sealed. If the vacuum needs to be run under open air for special requirements, don t run the pump over 3 minutes. 6. Do not run the vacuum pump without material in the pot. Do not block the pump exhaust when running. 7. Check and lubricate the bearings and other critical components regularly. 8. Keep homogenizing pot clean. Wash the parts where the homogenizing pot is connected with the working fluids in every stop and change of materials, especially the cutting wheel and cutting sleeve on the head and sliding bearings, bushings within the homogeneous sleeve. After cleaned and re-assembled, hand-turning impeller should be no clamping stagnation. Jog homogenizer motor to turn in the right way when pot lid and body flanges are relatively fixed. If no other abnormalities, the machine can start running. 9. Cleaning standards are based on the material property and customers specific needs. 9

10 Chapter8 - Troubleshooting Symptom Cause Solution Vacuum can not be achieved 1. Valves not closed; vacuum valve on pot lid is not open; 2. Seals were damaged; 3. Vacuum pump is not working 1Close all valves; 2 Replace seals; 3Check vacuum pump, Please seethe vacuum pump manual Vacuum pump can not generate Vacuum 1. There is no working fluid in pump; 2. There is big vacuum leak spot; 3. Pump is turning in a wrong direction 1 Check fluid. ; 2 Check for leakage. 3 Rewiring the motor.. Homogenizing, stirring motor can not start or overload Scraper does not follow the wall or run with scratch Noise Working fluid in vacuum pump flows into pot and Purifying equipment 1. Power supply broken.; 2. Motor bearing damaged; 3. Homogenizing rotor burned out; 4. Homogenizing head or stirring frame is jammed; 5. Motor has short circuit inside 1. Stir frame is off center.; 2. Stir frame base is jammed; 3. Stir frame is damaged The vacuum valve was not closed when shutting down the vacuum pump 1 Check wiring; 2 replace motor bearing; 3Check if homogenizing rotor rotates smoothly, 4 Clear the jam 5 Check motor coil 1 Adjust the stir frame 2 Clean up the base 3 Replace damaged parts 1Turn off the vacuum valve before shutting down the vacuum pump 10

11 Chapter9 - Electric Schematics Isotropic pot home pressure element Lid lower electromagnetism valve Lid raise Isotropic pot tilt Lid raise tie-in Lid lower tie-in Chapter10 - Hydraulic Pressure Control Valve pressure element switch throttle Isotropic pot tilt tie-in Isotropic pot home tie-in 11

12 The hydraulic system has been adjusted properly. There is no need to adjust it by customer. If customer needs to adjust the speed of the lid and the main pot for special purpose, please adjust the valve according to the figure. Chapter10 - Hydraulic Pressure Schematic Chart Apellation Cylinder Cylinder Flow control Pilot check valve Direction valve Pressure Gauge Check valve Hydraulic pump Filter Overflow valve Motor Tank Model 140/100X /32X330 1 L-10B 2 2AY-F10D-AB 1 34BOWEH10B-T MPa 1 KF-L-8/14 1 L 型 YB F-F10-D-AB/ Kw-240V Accompanying Documents 1YX-VME350L Vacuum emulsifying machine manual 2An instruction book of vacuum pump 3An instruction book of frequency changer 4Certificate of quality 12

13 12. Packaging and Shipping The machine should be packed with the film and wooden packing No crashes and damages in transportation The machine should be put in the clean and dry warehouse and make sure no corrosive gas around. 13