ELECTRIC TOPS AND RANGES

Transcription

1 ADVANCIA ELECTRIC TOPS AND RANGES MANUFACTURERS INSTRUCTIONS Part D: Maintenance manual - WARRANTY - To ensure the guarantee on this equipment, you should comply with the MANUFACTURER S INSTRUCTIONS in this manual. However if you cannot undertake the required maintenance operations, our installation and service network is available to provide you with a personalized contract. - WARNING - The product delivered to you complies with current standards. If any modifications are made the manufacturer cannot accept any responsibility whatsoever. The manufacturer cannot be held responsible in the event of inappropriate use of the equipment. This equipment is intended for use by suitably trained professionals Read all the documentation before installation Keep your documents for future reference. 3BE390843NM

2 Page 1 3BE390843NM 01/12 CONTENTS ELECTRIC TOPS AND RANGES 1 WIRING DIAGRAMS RADIANT HOBS ELECTRIC SOLID TOPS PLANCHA ELECTRIC RINGS BAIN MARIE CHIP STORE WITH INFRA-RED ELECTRIC OVEN BLOWN AIR HEATING OPTION ADVANCIA PLUS PLANCHA WATER SUPPLY CHANGING COMPONENTS ACCESS TO COMPONENTS LOCATED BEHIND THE FACIA INDUCTION CONNECTION GENERATOR / MAINS CONNECTION GENERATOR / INDUCTOR CONNECTION GENERATOR / CONTROLS FAULT DISPLAY FRONT LINE SPARE PARTS... 17

3 Page 2 3BE390843NM 01/12 1 WIRING DIAGRAMS 1.1 RADIANT HOBS RADIANT HOBS WIRING SCHEMATIC LISTING Ref Description Quantity Code H1 H2 Heating indicator light S1 S2 Thermostatic switch R1 R2 Radiant hobs 230V V Xa Terminals

4 1.2 ELECTRIC SOLID TOPS Page 3 3BE390843NM 01/ WIDE SOLID TOP WIRING SCHEMATIC WIDE SOLID TOP WIRING SCHEMATIC TRI 230V

5 Page 4 3BE390843NM 01/12 WIRING SCHEMATIC 400V THREE PHASE LISTING Ref Description Quantity Code H1 to H4 Heating indicator light S1 to S4 Thermostatic switch R1 to R4 Radiant hobs 230V V Xa Terminals 230V V V V V Xb to Xb2 Connectors

6 1.3 PLANCHA Page 5 3BE390843NM 01/ WIDE PLANCHA WIRING SCHEMATIC 230V THREE PHASE WIRING SCHEMATIC 400V THREE PHASE

7 WIDE CHROME PLANCHA AND 600 WIDE PLANCHA WIRING SCHEMATIC 230V THREE PHASE Page 6 3BE390843NM 01/12 WIRING SCHEMATIC 400V THREE PHASE

8 Page 7 3BE390843NM 01/ WIDE PLANCHA WIRING SCHEMATIC 230V THREE PHASE WIRING SCHEMATIC 400V THREE PHASE

9 WIDE CHROME PLANCHA AND 1000 WIDE PLANCHA WIRING SCHEMATIC 230V THREE PHASE Page 8 3BE390843NM 01/12 WIRING SCHEMATIC 400V THREE PHASE LISTING Ref Description Quantity per model Code R Element 1800 watt Hr - Hr1 - Hr2 Heating indicator light Sr - Sr1 - Sr2 Control thermostat Standard version Chrome option Xa Terminals Xb Connectors

10 1.4 ELECTRIC RINGS Page 9 3BE390843NM 01/ WIDE TWO RING HOB WIRING SCHEMATIC WIDE 4 RING HOB WIRING SCHEMATIC 230V THREE PHASE

11 Page 10 3BE390843NM 01/12 WIRING SCHEMATIC 400V THREE PHASE LISTING Ref Description Quantity per model Code H1 to H4 Heating indicator light S1 to S4 Switches R1 to R4 Optimum 900 electric rings 230V V X1 Terminal 230V V X2 Connector

12 Page 11 3BE390843NM 01/ BAIN MARIE Thermostat 1500 watt element Energy regulator Heating indicator light Cold water solenoid Push button LISTING Ref Description Quantity Code B1 Thermostat R watt element A1 Energy regulator Hm1 Heating indicator light S1 Push button Yr Cold water solenoid CHIP STORE WITH INFRA-RED WIRING SCHEMATIC LISTING Ref Description Quantity Code H1 Heating indicator light R Ceramic heat emitters S1 On / Off switch Xa Terminals Xb Connectors

13 1.7 ELECTRIC OVEN Page 12 3BE390843NM 01/12 POWER SCHEMATIC 230V THREE PHASE POWER SCHEMATIC 400V THREE PHASE LISTING Rep. Description Quantity Code B1 Safety thermostat H1 Heating indicator light R1 - R5 Roof elements 1 (230V) (400V) R2 - R6 Base elements 1 (230V) (400V) B2 Control thermostat S2 - S5 Switch X1 Terminals

14 Page 13 3BE390843NM 01/ BLOWN AIR HEATING OPTION POWER SCHEMATIC LISTING Ref Description Quantity per model 400 / / 1000 Code Hm Heating indicator light M1 - M2 Fan heater Sma On / Off switch Sr Control thermostat Xa Terminals Xb - xb Connectors ADVANCIA PLUS PLANCHA WATER SUPPLY LISTING Ref Description Quantity Code Sef Water push button Yef Cold water solenoid Xa Terminals

15 Page 14 3BE390843NM 01/12 2 CHANGING COMPONENTS 2.1 ACCESS TO COMPONENTS LOCATED BEHIND THE FACIA - Unscrew both M5 x 16 screws under the facia. - Tilt the facia: pull downwards slightly 1 then pull it towards yourself The facia can be locked in this position, ensure both lugs are located in the slots in the lower edge of the aperture.

16 3.1 CONNECTION GENERATOR / MAINS Generator terminals Page 15 3BE390843NM 01/12 3 INDUCTION To connect or disconnect the cabling insert a flat screwdriver into the slot and lever to release the clamp. 3.2 CONNECTION GENERATOR / INDUCTOR SCHEMATIC Channel B Channel C - Pu 9F 9W - Pu 9F 9W Blue wire Brown wire Blue wire Brown wire Blue wire Brown wire Blue wire Brown wire Connections: Rear inductor on Channel C Front inductor on Channel B Attention: Ensure the wiring to the inductors and temperature sensors passes to the right of the generator (viewed from the front). Rear inductor 3.3 CONNECTION GENERATOR / CONTROLS LED connections Lamps Poti Control C Poti Lamps Control B PwrMgmt rt gn PwrMgmt rt gn Blue wire Green wire to green light Red wire to red light Connections: Rear controls on Control C Front controls on Control B

17 3.4 FAULT DISPLAY Page 16 3BE390843NM 01/12 Error messages may appear when the unit is first switched on or after prolonged use. The red alarm light will stay on permanently if there is a fault. The green alarm code light will illuminate once for a long period then flash a number of times repeatedly. The number of flashes corresponds to the error code number These temporary indications do not mean there is necessarily a problem with the unit and it may continue to be used. If the unit fails to function inform the service technician of the message, conditions and frequency it appeared. Problem Possible causes What to do? The unit does not work the display is blank Error code number: 1 Error code number: 2 Error code number: 3 Error code number: 4 There is no electrical supply to the unit. The supply or the connections are faulty The unit has not detected a pan. The pan you are using is not suitable for induction cooking No inductor, no power to the supply side Ventilation ducting is blocked, fan is dirty, probe has failed Pan is empty or temperature probe defective Check the state of the electrical installation. Put a pan on the heating area. Use a suitable magnetic pan. Check the inductor Check the state of the electrical installation. Connect the inductor Clear the air circuit, clean the fan. Remove the pan, wait until the cooking surface cools down. Replace the probe. Error code number: 5 Control unit is defective Check / replace the control unit. Error code number: 6 Error code number: 7 Ventilation ducting is blocked, fan is dirty, temperature probe has failed The inductors temperature probe has short circuited Clear the air circuit, clean the fan Check / replace the probe. Error code number: 8 An electrical phase is down Check the phases Error code number: 11 Hardware initialisation error Control connected unnecessarily Wait the unit reboots automatically every 30 seconds. Connect the controls to an appropriate switch Error code number: 13 Indicates local under or over voltage Check the connections to the mains Error code number: 14 Error code number: 15 Indicates under or over voltage to the unit Pan is empty or temperature probe defective Check the connections to the mains. Remove the pan, wait until the cooking surface cools down. Replace the probe if necessary, switch the unit off for a few minutes then on again NOTE: When first connecting the unit wait a few seconds before touching the control panel to allow the electronics to stabilise.

18 Page 17 3BE390843NM 01/12 4 FRONT LINE SPARE PARTS Description Code 300 x 300 3,5 kw 230V radiating hob x kw 400V radiating hob Heating tangential fan way 1 x 5 L/min solenoid valve On / Off switch On / Off switch On / Off switch diameter black 4A 250V COSSE push-button Potentiometer switch On / Off switch Bain marie thermostat C three-pole thermostat Switch thermostat for infrared hob C thermostat C three-pole thermostat C three-pole thermostat C three-pole thermostat Simmerstat Oven top heating resistance 230V Oven top heating resistance 400V Oven bottom plate heating resistance 3300W 230V Oven bottom plate heating resistance 3300W 400V W heating resistance W/230V stainless steel 309 bain marie resistance diameter, 400V heating plate diameter, 230V heating plate W heating bent emitter x 5 kw generator x 270mm dia induction coils Potentiometer and indicator light Green indicator 230/400V, complete Ball and plug valve with nut circular hob vitroceramic plate Induction air inlet filter