INSTRUCTION MANUAL OF WATER DISPENSER ΜΟDEL: CLWD-19PW

Transcription

1 INSTRUCTION MANUAL OF WATER DISPENSER ΜΟDEL: CLWD-19PW Read these instructions carefully before using your new machine. Retain these instructions is a safe and convenient location. SAFETY INSTRUCTIONS Do not use for dispensing beverages other than water. Do not stack or place objects on top of the cooler. Unplug the power cord before cleaning or replacing any parts of the cooler. Connect the power cord directly to a grounded wall outlet. Do not connect to an extension cord. The water dispenser should be placed at least 10 cm away from the wall.

2 1. Specifications & Parts Identification 2. Installation Precautions The unit s power source is 220V. Only connect the power cord to a grounded 220V outlet. Only connect the power cord to a wall outlet. Do not use an extensions cord ROHS The symbol on the product means that at the end of its life, the appliance has not to be considered a common waste. It is a special waste and has to be demolished in specific recovery and disposal area, as prescribed by the EC Directive 2002/96/EC(WEEE). By disposing this product correctly, you can avoid negative consequences for the environment and for the human health, due to the presence of potentially dangerous substances in the product. Attention 1

3 3. Placement of your new unit The recommended placement of the dispenser is indoors. Placement location should be away from direct sunlight and excessive heat, cold and moisture. Place the dispenser on a flat and stable surface. Unbalanced placement may cause excessive noise and/or shaking of the unit. Place the dispenser in a well-ventilated area. Please allow a minimum of 10 cm from the wall for proper function of the condenser coil located on the back of the appliance. Avoid harmful gas or excessive heat. Placement of the dispenser should be in an area free from harmful gases and excessive heat sources. 2

4 4. Installation Procedures Verify that the stainless steel cold water baffle is securely in place before placement of water bottle. Remove plastic cap from bottle. If the cold water baffle is removed, water will not be cooled. Turn the water bottle upside down, filling the stainless steel tank visible inside of the top of dispenser. Fill with bottled water only. Filling with beverages other than water may cause significant problems to the dispenser. To prepare your hot water function, press the hot water button to allow air inside the hot water tank to escape. Release when water starts to flow. Be sure to complete this step before connecting the dispenser to the wall outlet. Supplying power to the hot water tank when empty may cause damage. The heating and/or refrigerating systems can be turned on or off by the switches located on the back of the cooler. If you prefer room temperature water, simply turn off either the heating or cooling system, and then you may dispense room temperature water from that spigot. Connect the power cord into a grounded 220V outlet. Allow a minimum of 30 minutes for water heating. Allow a minimum of 45 minutes for water cooling. 3

5 5. Operating your water dispenser This water cooler features two easy-to-use push buttoins. 1. The right button supplies cold water ranging from 5 C ~ 10 C. 2. The left button supplies hot water ranging from 78 C ~ 85 C. To activate, push the safety catch to the left and press the button located on the top of the unit. 3. The front panel has three indicator lights to indicate the power, heating and cooling systems are on. The green light indicates the power is on. The red light indicates that the heating system is on. The blue light indicates that the cooling system is on. The green light should remain on at all times. The red and blue lights will go off when the system cycles off, and the water has reached the appropriate temperature. 4. Your unit s hot and cold water settings have been set at the factory (cold 5 C ~ 10 C, hot 78 C ~ 85 C). If you wish to adjust the cold water setting, you may do so simply by inserting a small, flathead screwdriver into the screw located at the cold water temperature setting located at the back of the cooler. Begin by adjusting in 1/8 turn increments. Clockwise to INCREASE cold and counter-clockwise to DECREASE cold. 5. Before using the water dispenser for the first time, you should execute an internal cleaning, by filling it with 5 liters if water and then drain it by pressing the hot and cold water buttons, in order to clean its internal tubes. Circuit Diagram 4

6 6. Cleaning your water dispenser It s easy to keep your high-quality, two temperature water dispenser in clean condition year round. Just keep several basic cleaning items on hand and set aside a few minutes to clean your dispenser every 3-6 months (recommended). Be sure to have the following items within reach before you begin cleaning your dispenser: Clean pair of rubber gloves Paper towels Clean scrub brush or cleaning pad Boiling water 10 easy steps: Note: Always wait until water bottle is empty before starting the cleaning process. 1. Unplug the dispenser s electrical cord from its outlet. Remove water bottle from the top of the dispenser s unit. 2. Carefully fill the reservoir with clean, boiled water. Let the water sit for 3 minutes to partially cool. Always use care around hot water! 3. Wearing rubber gloves use a clean scrub brush or cleaning pad to gently clean the reservoir and baffle. (NEVER USE SOAP, CLEANING FLUID, STEEL WOOL OR OTHER ABRASIVE MATERIAL TO CLEAN THE UNIT). 4. Drain the water in the reservoir completely by pressing the dispenser buttons. Fill the reservoir again with clean, boiled water. Wait another 3 minutes for the water to cool and then gently clean the reservoir again with the scrub brush or cleaning pad. Wipe outside of the dispenser, including the dispenser buttons, body and handles. 5. Drain the reservoir completely by pressing the dispenser buttons. 6. Place a new, full bottle of water on top if the dispenser unit. 7. Remove the air from the tank by pressing the hot water button until the water flows freely. To activate, push the safety lever to the left and press button. 8. Plug in the dispenser and wait a few minutes for the water to heat up and cool. Enjoy your clean dispenser! Note: Wait until all the air has been removed from your water dispenser before pluging it back into an electrical outlet. Always use a grounded electrical outlet. 5

7 7. General Precautions The water from the ht faucet is extremely hot and can cause injury. Children should not be allowed to operate the hot water faucet. The cooler is equipped with a child resistant hot water dispensing device to help prevent injury to children. Use bottled water only. Filling the dispenser with any other type of beverage(s) may cause significant problems and will void all the seller s warranties. Keep the condenser free from dirt and dust. The cooling performance decreases when dirt and dust accumulate on the condenser. Disconnect the power cord and completely drain the hot water tank if the dispenser is not to be used for an extended period of time. The hot water tank can be drained by removing the hot water tank drain cap located on the back of the dispenser. Disconnect the power cord from the wall outlet before cleaning and/or inspection to avoid electric shock. Power interruption When the power cord is disconnected, wait a minimum of 5 minutes before reconnecting. When the power is temporarily turned off, disconnect the power cord from the wall outlet and wait a minimum of 5 minutes before reconnecting after power is restored. 6

8 8. Troubleshooting Guide Problems Causes Solution No cold water and no hot water Cold water not available Power cord is not connected to the outlet or dispenser Fuse blown The cold water temperature control dial is set to low cooling Excessive use of cold water The cold water switch is in the OFF position Poor ventilation Verify connections and power availability Replace fuse Set the temperature control dial to a colder setting Wait 45 minutes until cold water is supplied again Switch to ON position Make sure the dispenser is at least 10 cm from the wall Cold water baffle is not set properly Secure the cold water baffle in the cold tank Water is exposed to direct sunlight and/or heat source Move dispenser away from direct sunlight and/or heat source Hot water not available Excessive use of hot water νερού The hot water switch is in the OFF position Wait 30 minutes until hot water is supplied again Switch to ON position Noisy operation Water leaks (outside) The dispenser is not level or is in contact with other equipment Cracks or pin holes on bottle Install on level floor. Move the dispenser away from other equipment Replace with new bottle Water leaks (inside) Unplug the water cooler and remove bottle immediately. Contact Customer Service. 7