TRADITIONAL KITCHEN AND PREP FAUCET INSTALLATION INSTRUCTIONS

Transcription

1 TRITIONL KITN N PRP UT INSTLLTION INSTRUTIONS Kitchen Model #s: Prep Model #s:

2 OR YOU IN YOUR INSTLLTION: Turn off water supply. Observe all local plumbing codes. Inspect plumbing for signs of damage. Replace as necessary. O NOT use petroleum based products on this faucet. RQUIR TOOLS: djustable Wrench ORIINL TORY POSITION MY IT KSPLS Phillips Screwdriver NW JUST POSITION LRS KSPLS hannel Locks NL POSITION Waterstone faucets are designed to be installed in 3 different faucet positions. hoose to have the handle on left, front or right. Your faucet is factory configured for the most common positions - a front and right side installation. To reverse this and have the handle positioned on the left, connect the hose for cold water to the hot supply and the hose for hot water to the cold supply. This will maintain the relationship of pulling the handle for hot water or pushing for cold water. NL ON LT NL IN RONT NL ON RIT UT INSTLLTION OUNTR Remove clamp nut () and washer () from threaded shroud (). it flexible hoses () and rigid sidespray tube () through hole on counter or sink. (No plumbers putty is required. O-ring seals base). Slide washer and thread the clamp nut onto threaded shroud. Tighten nut snug to underside of sink or counter. Turn faucet to the desired handle position. Securely tighten clamp screws ().

3 OW TO JUST NL POSITION N NL TNSION I.1 ORIINL TORY POSITION MY IT KSPLS NW JUST POSITION LRS KSPLS On some kitchen countertops, the handle may hit the backsplash when the faucet handle is positioned to the left or right (ig. 1). Waterstone gives you the option of adjusting the handle 45 degrees to avoid hitting backsplash. 1. Place a small standard screwdriver in slot at bottom of metal ring that surrounds handle button (). ently pry button from handle (). 2. Unscrew and remove holding screw () and washer (). 3. old handle in a vertical position. Wiggle and pull straight off faucet. Rotate handle away from backsplash 45 degrees then slide handle back onto valve stem (). 4. Insert holding screw with washer and tighten. Snap handle cap back into place. 5. To adjust handle tension, turn ring () clockwise to increase or counterclockwise to decrease handle tension. ONNTIN SUPPLY OSS 1. efore connecting supply hoses, flush supply stops to clear any debris. Place a bucket underneath stops and run water for 5 to 10 seconds. Turn water off. 2. arefully position hot and cold supplies so they will not interfere with other hoses. 3. onnect supply hoses () to supply stops (). O NOT use teflon tape or plumbers putty. Turn water back on and check for leaks. OPTIONL ORTIV UTTONS TRITIONL ONLY - 3 INLU OMPSS / OMPSS / INIS MT 1. To remove, place a small standard screwdriver in the slot at bottom of metal ring that surrounds the handle buttons. ently pry the button from faucet handle. 2. To replace, position button and snap in with thumb. ONNTIN OPTIONL SI SPRY OUNTR Insert side spray base () into hole on your sink or counter. No plumbers putty is required. O-ring will seal base. Screw on attaching nut () and securely tighten. Slide sidespray hose () through side spray base. Turn off water supply. On the faucet, remove cap () from end of sidespray hose tube (). onnect and tighten sidespray hose to faucet hose tube.

4 INSTLL OPTIONL SOP/LOTION ISPNSR Pull and remove spout () from dispenser body (). Remove clamp nut () from threaded shroud (). OUNTR 1-3/8 OL it dispenser body through 1-3/8 hole on counter or sink. (No plumbers putty is required. O-ring seals base). Screw clamp nut onto shroud and tighten snug. ill plastic bottle with soap or lotion. Thread bottle () into bottom of dispenser shroud Insert open end of red tubing down through dispenser base and into plastic bottle. Push down on spout to secure over white O-rings. Slide red tubing () into tube fitting () at bottom of spout. Pump spout a few times to get soap or lotion flowing. INSTLL OPTIONL IR SWIT 1-1/2 OL XPOS TRS OUNTR efore inserting air switch into hole, loosen switch base () until threads are exposed. Slide clear tubing () into tube fitting () at bottom of air switch shroud. it air switch and tubing through 1-1/2 hole on counter or sink. (No plumbers putty is required. O-ring seals base). Slide washer up then screw the clamp nut onto threaded shroud. and tighten nut to underside of sink or counter until snug. ONTINU ON NXT P

5 ONTINU ROM PRVIOUS P R ISPOSL Tighten clamp screws () securely with screwdriver. and tighten switch base back down to cover threads. Slide other end of tubing () into tube fitting at bottom of control box (). Plug control box into undersink electrical outlet. Plug garbage disposal into either dual outlet. INSTLL SINL PORT IR P (OPTIONL) /2 OL Twist and pull air gap cover () off of upper cap nut (). Unscrew and remove cap nut from piping (). Unscrew and remove top clamp nut () from both threadings on piping. Slide gasket () off piping and remove. rom underneath counter top, fit air gap piping upward through 1-1/2 hole Slide gasket down and screw top clamp nut back onto piping. djust the two clamp nuts to fit countertop thickness. (No plumbers putty is required). Screw cap nut back onto top of piping until snug. Slide air gap over cap nut and top clamp nut. e sure to have overflow holes () facing sink. Slide small intake hose () over small connector. Slide larger drainage hose () over large connector. Tighten hose clamps. Turn on water supply and check for leaks.

6 INSTLL UL PORT IR P (OPTIONL) 1-1/2 OL Pull air gap () off of upper cap nut (). Unscrew and remove cap nut from piping (). Unscrew and remove top clamp nut () from both threadings on piping. Slide gasket () off piping and remove. rom underneath counter top, fit air gap piping upward through 1-1/2 hole. Slide gasket down and screw top clamp nut back onto piping. djust the two clamp nuts to fit countertop thickness. (No plumbers putty is required) Screw cap nut back onto top of piping until snug. Slide air gap over cap nut and top clamp nut. e sure to have overflow holes () facing sink. J Slide small intake hose () over small connector. Slide larger drainage hose () over large connector. Tighten hose clamps. M L K Third intake hole (J) has 3 options. Use hose connector (K) for additional dishwasher, use filtration hose connector (L) for reverse osmosis unit, or use solid cap (M) to plug third hole Raintree ourt Murrieta, VN-038-TKP Rev.