Model: R20C/H. Submittal B. Replacement R20 Series Horizontal PTACs & PTHPs. Replacement for (Chassis Option - A):

Transcription

1 Submittal Replacement R0 Series Horizontal PTACs & PTHPs Model: R0C/H R 0 0 B Model Series: [R0= Repl.] Operation: [C=Straight Cool] [H=Heat Pump] Compressor: Special Rev: Cooling Capacity: [09=9,000 Btuh] [1=11,000 Btuh] [1=1,700 Btuh] [18=1,600 Btuh] (Straight Cool Only) Voltage: [A=11V/] (09 Straight Cool Only) [D=08-0V/ (Std)] [E=6-77V/] Auxilary Heat: [*See Specifications- Electrical Data] [0=None (Std)] *[=kw@0v] or [=kw@6v] *[=kw@0v] or [=kw@6v] or [=1kW@11V] *[=kw@0v] or [=kw@6v] *[=kw@0v] or [=1.kW@11V] Cond. Coil Option: [A=Standard (Al/Cu)] [B=Coated (Al/Cu)] Chassis Option: [A=Standard] [D=Fedders CMEO Unizone (R80)] Air Options: [A=Bottom Return, No Fresh Air (Std)] [B=Bottom Return, Motorized FA Damper] [C=Front Return, No Fresh Air] [D=Front Return, Motorized FA Damper] Product Revison: Controls Options: [See Accy list for Hyd Vlv & T stat] [0=Unit Mount w/ Electric/NO Heat] [1=Vac T stat w/ Electric/NO Heat] [=Unit Mount w/ Hyd Ht (Line V Vlv)] [=Vac T stat w/ Hyd Ht (Line V Vlv)] [= Unit Mount w/ Hyd Ht (V Vlv)] [=Vac T stat w/ Hyd Ht (V Vlv)] Replacement for (Chassis Option - A): Adirondack Aire CH/RM, Applied Comfort SCEA/SCHA, Climate Master 70-, Friedrich 70/70, Comitale CTPI, Cool Heat RM, Ice Air RSCM/A/RSZ, Ice Cap RSZ, Islandaire CM/RM/SC, Simon-Aire SSZ, TPI Ra-Matic, Weather Twin RM/S/ SC, Zoneaire RM/SC. Replacement for (Chassis Option - D): Comitale CFOO, Fedders CMEO Unizone, Ice Cap RSU, Islandaire UN, Mueller/ Worthington Climatrol, Retroair R80 Number of Units Ordered Made in the USA Approved: Reviewed: Contact: Address: Phone: Unit Tag # REVISON By: Approval 1

2 QTY Ordered Indicate the quantity of field installed accessories, required for each unit Description Thermostat, Single-Stage, 1-Heat/1-Cool, Vac, Programmable, ICM, Manual Changeover (PN ) Thermostat, -Stage, -Heat/-Cool, Vac, Programmable, ICM, Manual Changeover (PN ) Thermostat, Single-Stage, 1-Heat/1-Cool, Vac, Programmable, ICM, Auto Changeover (PN ) Thermostat, T9000, Wireless, Battery, Single Stage, 1-Ht/1-Cl, /- Prog, MCO [# also required] (PN ) Remote Control Node, T9000, Printed Circuit Board, Wireless, Vac, 1/unit req d [# also required] (PN ) Isolation Ball Valve, 1/, Sweat Connections (PN ) Kit, Cabinet Assembly, White Pearl, Aluminum Supply Air Louver, w/ Kick-plate & Control Door, R0 (PN ) Kit, Wall Sleeve & Louver, Architectural Aluminum Outdoor Louver, R0, 10/1/1/16/18 Depths (PN [ / / / / 6 ]) Kit, Hydronic/Steam Coil, 1-Row, Al-Cu, Left-Handed Piping, R0 (PN 00019) Kit, Hydronic/Steam Coil, 1-Row, Al-Cu, Right-Handed Piping, R0 (PN 00011) Kit, Aquastat, Hydronic Heat, Hot Water Sensor-Relay [Energizes Fan] (PN 00008) Kits, Water Valves, w/ Actuator, /-Way, Line/Vac, NO/NC, Sweat (Several Kits Available-Consult Factory) Job-Guide Specifications Standard Warranty: 1 Year - Parts & Year - Compressor High Pressure Switch with Integral Compressor Lockout Microprocessor Control Board Diagnostic LED Codes with Test Mode Thermally-protected PSC fan motors Indoor Coil Freeze & Anti-Short Cycle (Compr), Protections Single Stage Heating Operation (w/ or w/o Electric Heat) DOE Performance Qualified & Listed ETL-US & Canada Listed for Safety to UL8 Standard Reversing Valve Energized in Cooling (Heat Pumps) Meets ASHRAE for Replacement Efficiencies Operating Range Mode OD Amb. Temp ID Amb. Temp Cooling Max 10ºF (1ºC) DB 80ºF (7ºC) DB Min ºF (0ºC) DB 60ºF (19ºC) DB Heating Max 7ºF (ºC) DB 80ºF (7ºC) DB Min 0ºF (.ºC) DB 6ºF (18ºC) DB Electrical Plug Configurations NOTICE: Due to ongoing product development; design, specification and performance data listed within this submittal document are subject to change without notice. For the most current performance data, please refer to RetroAire listings of certified products in the DOE directory, or consult the factory. ECR International, INC. 01 Dwyer Avenue Utica, NY info@retroaire.com FAX RETRO Sales: Customer Service : 1 (800) -96

3 Specification and Performance Model: R0C/H Product Description RetroAire Replacement Packaged Terminal Air Condition/ Heat Pumps units are straight cooling (PTAC) or heat pump systems (PTHP). Both PTAC and PTHP configurations fit wall sleeves. Heat pumps (PTHP) operate in mechanical heat mode down to outdoor temperature of 0 F (. C). Below 0 F (. C) heating is accomplished by auxiliary heat option. ETL listed to UL8, CAN/CSA C. No Retroaire PTAC/PTHP R-10A refrigerant. High-efficiency rotary compressors. Two fan speeds. Positive condensate re-evaporation. PTAC/PTHP units are available in nominal sizes of 9,000 Btuh, (.6kW) 1,000 Btuh (.kw) or 1,000 Btuh (.kw). PTAC units (straight cooling only) are available at 18,000 Btuh (.kw). Coefficient of performance (COP) ratings.0 for heat pumps. Standard Controls And Components Construction Chassis constructed of 0 gauge galvanized steel. Condenser baffle options accommodate extended wall sleeve applications. (Consult manufacturer). Powder-coated condenser and evaporator drain pan. Foam strip seal for supply air duct. Weather strip insulation. Air Systems Thermally-protected motors PSC type. Indoor fan forward curved type, directly mounted to motor shaft. Unit mount controls include field selection switch to control indoor fan by either cycling with compressor operation or continuously with unit. Condensate Removal Outdoor fan incorporates condensate slinger ring. Condensate is thrown onto coil, where it evaporates. Thermostatic drain pan valve for condensate elimination when outdoor temperature drops below 60 F (1 C) (heat pump units only). Controls Unit-mounted operating controls include thermostat, fan speed control, heat/cool switch, fan cycle switch, fresh air switch (if equipped). Use of optional 1-stage or -stage thermostat. stage thermostat is capable of activating emergency heat if auxiliary heat source is available. Low ambient protection see "Microprocessor control board" for details. Ability to control a normally-open or normally-closed motor valve switch (on hydronic heat units only). Valve controls must be ordered for V or line voltage. All hydronic heat units include molex plugs for connection of hydronic valve motor. Optional wall thermostat controls include fan speed control and fresh air switch (if equipped). Equipped with manual reset high pressure switch which prevents abnormal high pressure operation. Microprocessor Control Board Universal control board used in straight cooling, electric resistance heat, hydronic heat, or cooling/heat pump applications. Random start timer prevents multiple units from simultaneous startups after power interruption or on initial power-up. Fan purge fan remains on for 60 seconds after heat/cool is satisfied. Anti-short-cycle compressor protection prevents compressor from rapid cycling. Freeze-protection prevents evaporator coil freeze up. Low ambient lockout prevents compressor operation in outdoor temperatures less than 0 F (. C). (On PTHP units supplied with unit-mounted control, control causes automatic changeover to auxiliary heat, if installed.) Test operation all timers are temporarily suppressed to allow ease of testing or troubleshooting. Control board LED provides self-diagnostic troubleshooting codes, see Installation, Operation & Maintenance Manual for Sequence of Operation.

4 PRODUCT DESCRIPTION - CONTI. Manufacturer Installed Options (Consult manufacturer) 6V (1 and 1 only) 11V (09 Model Only) Corrosion-resistant coil option used for seacoast and harsh-environment usage; coated aluminum fin/copper tube condenser coil. Motorized fresh-air damper Supplemental electric heat Hydronic heat controls Front air intake Field-Installed Accessories Hydronic heat coil assembly is shipped loose for field installation. Wall thermostat digital 1-stage or -stage available. Wall sleeves, louvers, and cabinets. Aquastat - delays fan start-up until coil reaches 100 F (8 C) to virtually eliminate "cold" blow condition. Hydronic control valve, water way & way. Hydronic control valve, steam way. Hydronic Isolation valve, 1/ in sweat connection.

5 PRODUCT FEATURES Indoor Coil Freeze Protection (standard) This feature will prevent the indoor coil from freeze up in the cooling mode. Indoor coil freeze up can occur due to a dirty air filter, restricted or poor air flow, low refrigerant charge or low room or outdoor temperatures. This in turn can cause compressor damage. Should a freeze condition be detected, the compressor and outdoor fan will be switched off for a minimum of three minutes until the freeze condition is satisfied. During this time the indoor fan will continue to run to aid in the defrost process. Condensate Removal (standard) The RetroAire replacement unit (cooling operation) is designed to eliminate condensate by slinging it onto the outdoor coil. Condensate drains through the bulkhead to the area near the outdoor fan. As part of its normal operation, the unit will produce condensate and collect it in the base pan of the unit. There it is picked up by the outdoor fan slinger ring and deposited onto the condenser coil. During the cooling season, this improves the unit s efficiency by maintaining reduced refrigeration system pressures. Base pan has overflow notches-if too much condensate is produced notches allow condensate to flow out of the base pan and into the wall sleeve out of the building. Thermostatic Drain Pan Valve (standard on heat pump units) On heat pump models (PTHP), condensate can accumulate in the outdoor drain pan during the heat pump cycle. PTHP units include a thermostatic drain valve that opens when outdoor temperatures fall below 60 F (1 C). When the drain valve opens, condensate flows from the drain pan onto the bottom of the wall sleeve, where it drains to the outside. This keeps the base pan free of condensate water, which could otherwise freeze during colder outdoor temperatures. Random Start Feature (standard) The random start feature is initiated on initial power-up or after a power interruption. The controller adds a random time delay (from 10 seconds) on start-up, preventing the compressor from starting. This staggers the starting of multiple units in a single facility, preventing a large surge that might occur if all units started at the same time. Anti-Short Cycle Timer (standard) The microprocessor control uses this timing to prevent shortcycling of the compressor. When the compressor cycles off on a heating or cooling call, the controller starts a 180-second timer. The compressor will not be allowed to start until this time has elapsed. On initial power-up or after a power failure, this timing occurs after the random start timing. Power Cord With Integral Safety Protection (standard) All PTAC/PTHP units rated 0V or less are equipped with a power cord with integral safety protection as standard. Providing personal shock protection as well as arcing and fire prevention, the device is designed to sense any damage in the line cord and disconnect power before a fire can occur. Tested in accordance with Underwriters Laboratories, the cord set also offers a unique passive operation, meaning the unit does not require resetting if main power is interrupted. Heat Pump Heat pump units are Limited Range and should be equipped with back-up electric resistance or hydronic heat. Limited Range heat pumps are designed to operate when outdoor temperatures are between 7 F( C) and 0 F(. C) and with a maximum indoor temperature of 80 F(6.6 C). The unit is equipped with a reversing valve that is energized for cooling and de-energized in heating mode. Electric heating or hydronic heat will operate using the on-board control logic below the operating conditions of the heat pump. Hydronic Heating (optional) An optional hydronic heat package may be selected in lieu of electric heat. Heating operation is essentially the same as that of units with electric heat. Aquastat Connection (optional) All replacement PTAC/PTHP's with hydronic heat are supplied with a standard line volt Aquastat connection. The field installed Aquastat delays the fan operation until the hydronic coil reaches a temperature of 100 F (8 C). Motorized Fresh Air Damper (optional) The optional motorized fresh air damper allows fresh air into the space to be conditioned. When the Fresh Air switch is in the "YES" position the damper door is open and allows fresh air into the space. This feature is only available when the indoor fan is on. When the damper door switch is in the "NO" position, the damper door is closed and does not allow air in the space. Optional Wall-Mounted Thermostats Thermostats compatible with your PTAC/PTHP unit: Select part number from the latest RetroAire price list for this option. This is a single stage, cool/heat, thermostat that can be used in all RetroAire cooling, heating or heat pump applications. The thermostat has an adjustable setpoint range of between F(7 C) and 9 F( C). For heat pumps another option is part number This is a stage heat/cool thermostat which allows for emergency heat. Selecting a thermostat (by others) When selecting a thermostat, choose a single stage heat/cool, v thermostat. Straight cooling with electric heat or hydronic heat, select a thermostat that is compatible with a cooling/electric heat system. Thermostat should have R, Y, W and G terminals. Heat pump with electric heat (PTHPs), select a thermostat that is compatible with cooling/single-stage heat/heat pump system. Thermostat should have R, Y, O and G terminals. RetroAire units are single stage heating only. The electric heat and heat pump will not operate simultaneously.

6 ELECTRICAL PERFORMANCE R0C09 &R0H09 - Electrical Data Power Supply Compressor ID Fan Motor OD Fan Motor Electric Heat Unit Electrical Ratings Voltage Min V RLA LRA FLA Hp FLA Hp Htr # Htr V Htr W Htr A TCA THA MCA MOCP Power 11V/ N/A P *08/0V/ **08/0V N/A P 1 6-1P 0 6-0P 6-0P 0 6-0P N/A P 6V/ * Toshiba Compressors **Tecumseh Compressors N/A P P P P R0C1 & R0H1 - Electrical Data Power Supply Compressor ID Fan Motor OD Fan Motor Electric Heat Unit Electrical Ratings Voltage Min V RLA LRA FLA Hp FLA Hp Htr # Htr V Htr W Htr A TCA THA MCA MOCP Power *08-0V/ **08/0V/ 6V/ N/A P 1 6-1P 0 6-0P 6-0P 0 6-0P N/A P 1 6 1P 0 6 0P 6-0P P N/A P P P P * Toshiba Compressors **Tecumseh Compressors Note: The listed THA value is the highest of both heating methods - heat pump & electric heat NOTICE: Due to ongoing product development; design, specification and performance data listed within this submittal document are subject to change without notice. For the most current performance data, please refer to RetroAire listings of certified products in the DOE directory, or consult manufacturer. 6

7 ELECTRICAL PERFORMANCE R0C1 & R0H1 - Electrical Data Power Supply Compressor ID Fan Motor OD Fan Motor Electric Heat Unit Electrical Ratings Voltage Min V RLA LRA FLA Hp FLA Hp Htr # Htr V Htr W Htr A TCA THA MCA MOCP Power N/A P P *08-0V/ **08-0V/ V/ * Toshiba Compressors **Tecumseh Compressors P P P N/A P P P P P N/A P P P P R0C18 - Electrical Data Power Supply Compressor ID Fan Motor OD Fan Motor Electric Heat Unit Electrical Ratings Voltage Min V RLA LRA FLA Hp FLA Hp Htr # Htr V Htr W Htr A TCA THA MCA MOCP Power N/A P P 08-0V/ V/ P 6-0P 0 6-0P N/A N/A 7-0P P N/A N/A N/A N/A N/A N/A N/A Note: The listed THA value is the highest of both heating methods - heat pump & electric heat NOTICE: Due to ongoing product development; design, specification and performance data listed within this submittal document are subject to change without notice. For the most current performance data, please refer to RetroAire listings of certified products in the DOE directory, or consult manufacturer. 7

8 ELECTRICAL PERFORMANCE Model Hydronic Coil Code Part Number Air Entering Dry Bulb Air Entering Wet Bulb Air Entering Flow Rate F C F C CFM m^/ min R R0 C/H Hydronic Heat Water Flow Water Entering Capacity GPM LPM F C Btu/h kw Pressure Drop ft HO m HO Water Leaving Water Delta F C F C , , , , , , , , , , , , , , , ,

9 PERFORMANCE DATA Models R0C R0C 09 R0C 1 R0C 1 Voltage Performance Data - Cooling Cooling Capacity EER Sensible Heat Ratio Indoor Air Flow Fresh Air Inlet Flow Outdoor Sound Level Shipping Weight Btuh (kw) CFM (L/S) CFM (L/s) dba lbs (Kg) A 11 0 (07.7) 9000 (.7) 9.0 D 08/ (16.) E (.8) (07.7 D 08/ (.) 0 (16.) E (.) 0 (07.7) D 08/0 00 (188.8) 100 (.) E 6 0 (1.) (17) 7 10 (6.) 0 () (6.) 60 (8) (6.) R0C 18 D 08/ (.6) (179.) 9 () (6.) Performance Data - Heating Models R0H Voltage Cooling Capacity EER Indoor Air Flow Cooling Heating Capacity COP Indoor Air Flow Heating Sensible Heat Ratio Fresh Air Flow Outdoor Sound Level Btuh (kw) CFM (L/S) Btuh (kw) CFM (L/S) CFM (L/S) dba Shipping Weight lbs (Kg) R0H 09 D 08/ (.7) (16.) 800 ( (189) E (.8) (07.7) 9100 (.7) 0 (1) 0.79 (17) 7 R0H 1 D 08/0 0 (16.) 00 (189) 1100 (.) (.).6 E 6 00 (188.8) 0 (1) () (6.) R0H 1 D 08/0 100 (.) (188.8) 1800 (.) 0 (1). E (.1) (1.) 100 (.) 00 (6) (8)

10 R0 C/H Chassis Fresh Air Switch (FAS) Fan Speed Switch (FSS) Fresh Air Switch (FAS) Thermostat Remote Mount Fan Speed Switch (FSS) System Switch (SS) Line Cord High Pressure Switch (HPS) reset Rating Plate Electrical Diagram Fan Cycle Switch (FCS) Aquastat W/ Jumper MTR Valve Unit Mount R0 C/H Chassis - Dimensions Dimensions in [ ] are in mm 10 Adjustable Weather Angle Dimension "A" 8 /8 7 7/8 9 11/16 (1) 8 () Dimension "B" 9 1/ 10 1/ 8 7/16 (1) 10 1/8 () Dimensions are calculated without foam gaskets. (1) Standard position Factory installed. () Position for Climate Master 70 and 70.

11 R0 C/H Wall Sleeve - Dimensions Wall Depths (A) (B) (C) 10" 1 1/" 8" 10" 1" 1 1/" 8" 1" 1" 1 1/" 8" 1" 16" 1 1/" 8" 16" 18" 1 1/" 8" 18" Top View Outside View R0 C/H Cabinet - Dimensions [Part #000116] 11

12 R0 C/H Misc. Product Data Operating Range Mode OD Amb. Temp ID Amb. Temp Cooling Max 10ºF (1ºC) DB 80ºF (7ºC) DB Min ºF (0ºC) DB 60ºF (19ºC) DB Heating Max 7ºF (ºC) DB 80ºF (7ºC) DB Min 0ºF (.ºC) DB 6ºF (18ºC) DB Replacement for (Chassis Option - A): Adirondack Aire CH/RM, Applied Comfort SCEA/SCHA, Climate Master 70-, Friedrich 70/70, Comitale CTPI, Cool Heat RM, Ice Air RSCM/A/RSZ, Ice Cap RSZ, Islandaire CM/RM/SC, Simon-Aire SSZ, TPI Ra-Matic, Weather Twin RM/S/ SC, Zoneaire RM/SC. Replacement for (Chassis Option - D): Comitale CFOO, Fedders CMEO Unizone, Ice Cap RSU, Islandaire UN, Mueller/ Worthington Climatrol Electrical Plug Configurations ECR International, INC. 01 Dwyer Avenue Utica, NY info@retroaire.com FAX RETRO Sales: Customer Service : 1 (800) -96