Operator & Parts Manual. wwwicecompanies.com. 175 RPM Floor Machine REV.01( ) INTELLIGENT CLEANING EQUIPMENT

Transcription

1 wwwicecompanies.com Operator & Parts Manual 75 RPM Floor Machine ip7 ip REV.0(0-09) INTELLIGENT CLEANING EQUIPMENT

2 READ OPERATOR MANUAL CAREFULLY IMPORTANT:To ensure full warranty protection,please fill out & return your warranty card. Please fill out at time of installation for future reference. Model No. Serial No. Machine Options Sales Rep. Sales Rep. phone no. Customer ID Number Installation Date HOW TO ORDER PARTS Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered online,by phone, by fax or by mail.. Identify the machine model.. Identify the machine serial number from the data label. 3. Ensure the proper serial number is used from the parts list.. Identify the part number and quantity. Do not order by page or reference numbers. 5. Provide your name, company name, customer ID number,billing and shipping address, phone number and purchase order number. PROTECT THE ENVIRONMENT Please dispose of packaging materials,old machine components such as batteries, hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations. Always remember to recycle. ICE Company Limited XiangShi Road LiaoBu DongGuan GuangDong China Tel: Fax: Specifications and parts are subject to change without notice. ICE ip7 ip0

3 TABLE OF CONTENTS SAFETY PRECAUTIONS MACHINE COMPONENTS MACHINE OPERATING INSTRUCTIONS MACHINE MAINTENANCE & STORAGE HANDLE RELEASE ASSEMBLY INSTRUCTIONS PARTS LIST WEAR & TEAR PARTS LIST SOLUTION TANK ASSEMBLY(OPYIONAL ) SPECIFICATIONS WIRING DIAGRAM ICE ip7 ip0

4 OPERATOR SAFETY PRECAUTIONS Carefully read and understand this manual before operating this machine. This machine must be grounded! This floor/finishing machine shall be grounded while in use to protect theoperator from electric shock.grounding provides a path of least resistance for electric current. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not remove the ground pin under any circumstances. This machine is for use on a nominal 0-volt circuit and has a grounding plug that resembles the plug illustrated in Figure. Make sure that the machine is connected to an outlet having the same configuration as the plug. No adapter should be used with this machine. This machine is intended for commercial use. It is constructed for use in an indoor environment and is nor intended for any other use. Use only recommended accessories.. Do not operate machine: Unless trained and authorized. Unless you have read and In flammable or explosive areas. understand the operators manual. With a damaged cord or plug With the use of extension cords. If not in proper operating condition. In outdoor areas and standing water.. Before operating machine: Make sure all safety devices are in place and operating properly. 3. When using machine: Do not run machine over cord. Do not pull machine by cord or plug. Do not pull cord around Do not unplug by pulling on the cord. sharp edges or corners. Do not stretch cord. Do not handle plug with wet hands. Keep cord away from heated surfaces. Report machine damage or faulty operation immediately. When moving, repairing and tilting the machine, make sure the safety installation is right place and tighten the release handle.. Before leaving or servicing machine: Turn off machine. Unplug cord from outlet. 5. When servicing machine: Unplug cord from outlet. Use manufacturer supplied or approved replacement parts. To avoid electrical shock,please replace the power cord immediately if any damage is being detected. The replacement must be performed only by an authorized person or by our customer service center. ICE ip7 ip0

5 OPERATOR MACHINE COMPONENTS Machine Description Machine Structure New structure design 7" 0r 0" Deck alumiunm 6" or 9" Pad Driver Triple Planetary All Steel Gear Box Universal Clutch Plate Safety Lock-Out Switch Security protection in an upright 50' Cord 66-Frame Motor. Deck. Wheel 3. Safety installation. Level Solution 5. Trigger 6. Safety Lock-Out Switch 7. Housing 8. Handle Release Assy 9. Top Cover 0. Motor. Clutch Plate ICE ip7 ip0

6 OPERATOR General Use: FLOOR MACHINE OPERATING INSTRUCTIONS ) Remove any obstructions or other obstacles in the area which is to be cleaned. ) Make sure the safety installation is right place and tighten the release handle. 3) Place handle in upright position and tilt machine back until handle rests on the floor. Be sure the machine is not plugged into an outlet. ) Remove the pad center gripping device by unscrewing the thumbscrews. 5) Place appropriate burnishing pad on pad driver and re-attach the center gripping device. 6) Place machine back into its upright position. 7) Plug power cord into grounded outlet. Do not use an extension cord in conjunction with the standard power cord. 8) Release the compression handle and adjust handle height to a comfortable operating position, then push back down on the compression handle to lock the handle in operating position. 9)To start the machine, push on the Blue safety button of the top of upper switch housing and squeeze either of the switch levers. 0) When the machine is in operation, both hands should be placed on the handle (switch housing). )To stop the machine at any time, simply release the switch lever, and the machine will stop automatically. MAINTENANCE To keep the machine performing well for many years, please follow the following maintenance procedures. Always confirm that the machine is unplugged prior to performing any maintenance or repairs.. Unplug machine as soon as you are done using it.. Make sure the safety installation is right place and tighten the release handle. 3. Tilt machine back and remove pad driver or brush. Never store a low speed machine with the pad driver or brush mounted to the machine.. Clean the outside of the machine with a mild cleaner. 5. Check power cord for any damage.if damage is detected, replacepower cord immediately. 6. Lubricate wheels with a water resistant lubricant once a month. 7. Check machine for loose or missing nuts and bolts, and replace as necessary. 8. If the machine is used in a dusty environment, you may remove themotor cover and blow the motor clean with compressed air. This willensure proper ventilation, and allowthe motor to run cooler. STORAGE ) Unplug machine from power source and wrap cord on handle. ) Tilt machine back and remove pad driver or brush. 3) Store in upright position in a dry area. ICE ip7 ip0

7 OPERATOR HANDLE RELEASE ASSEMBLY INSTRUCTIONS Step ) Assemble handle and handle release assembly: According to in the following photos direction assembly. ) Adjust the nylon lock nut: It don't over tighten nylon lock nut, only tighten it enough to hold handle in place when compression lever is in down position. Step 3 ) Connect power cords together Step ) Take out the handle assembly, nut lock M, hex. socket head Mx0. ) After Aligning them, and use spanner to tighten them. 7 ICE ip7 ip0

8 PARTS LIST ip7 & ip0 HANDLE ASSEMBLY ICE ip7 ip0 8

9 ip7 & ip0 HANDLE ASSEMBLY DIA PART NO DESCRIPTION NO NUMBER REQ'D 0855 SCREW M8X BRACKET TUBING 30 NUT LOCK M WASHER PLAIN Ø0.5XØ0X NUT LOCK M WASHER PLAIN Ø8XØ6.5X HOOK CABLE CLAMP TANK SCREW M5 X 0 HEX SOCKET 0030 CORD POWER SUPPLY 3500 TOOTH WASHER Ø5 3 5 SCREW M5X SCREW MX STRAIN RELIEF CORD TOOTH WASHER Ø PIN LEFT TRIGGER SWITCH LEVEL SOLUTION REAR COVER 66 WASHER PLAIN Ø SCREW M6 X SCREW M6 X SERIAL NUMBER[iP7] 0033U SERIAL NUMBER[iP0] CIRCUIT BREAKER 0A COVER BALL BASE 8 08 SCREW MX RIGHT TRIGGER SWITCH SCREW M3X TOOTH WASHER SPRING SAFETY SWITCH SAFETY BOTTOM SAFETY SPRING FRONT COVER ICE LOGO CLAMP CORE 9 ICE ip7 ip0

10 ip7 & ip0 HANDLE ASSEMBLY SCREW MX SCREW M8X60 33 HANDLE RELEASE 6785 PIN Ø8X VOLT HANDLE RELEASE 3303 WASHER PLAIN HANDLE RELEASE COVER HOOK HANDLE CORD HANDLE PLUG PROTECTOR COVER GROMMET WASHER NYLON PLAIN Ø8 ICE ip7 ip0 0

11 PARTS LIST ip7 & ip0 BASE ASSEMBLY ICE ip7 ip0

12 ip7 & ip0 BASE GROUP DIA PART NO DESCRIPTION NO NUMBER REQ'D 000 BUMPER 7" [ip7] 000 BUMPER 0" [ip0] 50 WASHER PLAIN Ø5 3 5 SCREW M5X PH 000 FRAME 7" [ip7] 000 FRAME 0" [ip0] 5 5 SCREW M5X PH BARB HOSE 7 35 NUT LOCK M SCREW M6 X WASHER PLAIN Ø6.XØ8X SCREW M6 X.7 06 WHEEL 5" 350 WASHER LOCK Ø 3 65 WASHER Ø.5XØ5X BRACKET LEFT ALUMMINIUM BASE MOTOR AXLE BRACKET RIGTH PLUG PROTECTOR MOTOR WITH GEAR BOX READ MANUAL LABEL 000 COVER MOTOR 0003 COVER TOP LOGO ICE 08 STATIONARY SWITCH CENTRIFUGAL SWITCH MOTOR 0V BOLT WITH WASHER KIT START-UP CAPACITOR(BIG) μF/300V 9 08 COVER CAPACITOR SCREW 8-3UNCX MOTOR LABEL 3 5 HEX SOCKET HEAD M X RUNNING CAPACITOR 60μF/50V ICE ip7 ip0

13 ip7 & ip0 BASE GROUP DIA PART NO DESCRIPTION NO NUMBER REQ'D SCREW 0-3X BIG WASHER RING GUARD COULPING SLEEVE GEAR BOX 0 8 WASHER PLAIN Ø8 8 WASHER LOCK Ø SCREW M8X "PAD HOLDER ASSY [ip7] "PAD HOLDER ASSY [ip0] WEAR & TEAR PARTS LIST DIA NO PART NUMBER DESCRIPTION NO REQ'D MACHINE 06 WHEEL 5" ip7&ip "PAD HOLDER ASSY ip "PAD HOLDER ASSY ip7 3 ICE ip7 ip0

14

15 DIA NO PART NUMBER ip7 & ip0 SOLUTION TANK ASSEMBLY DESCRIPTION NO REQ'D 05000U SOLUTION TANK ASSEMBLY(OPTIONAL) 003 CHAIN SEAT,CHAIN 00 SCREW,M5,BRASS SEAL,TANK KNOB,M5X UPPER PULLING ROD BRASS VALVE ASSEMBLY SEAL NUT,/-0UNF 005 BARB,HOSE,SOLUTION 0006 BARB HOSE SCREW,M5X0,HEX SOCKET 0003 CLAMP,TANK NUT,LOCK,M CLAMP,HOOK TANK ICE ip7 ip0 5

16 OPERATOR SPECIFICATION Model ip7 ip0 Voltage 0 V 0 V Power.5HP.5HP Current 3 A 3 A Frequency 60 Hz 60 Hz Speed 75 rpm 75 rpm Deck Size 7" (3 cm) 0" (50 cm) Length of power cord 5 m 5 m Weight.5 Kg 5 Kg Dimension LXWXH 56X3X cm 57X5X cm Wiring Diagram Switch Housing 0V 60Hz Single Phase Power Supply Black White Green Switch Circuit Breaker Red Motor Red White White Startup Capacitor μF/300V STO /3C Power Supply Cord Handle Cord Motor Cord Running Capacitor 60μF/50V ICE ip7 ip0 6

17 ICE Company Limited