Washer-Extractor. Parts. Refer to Page 4 for Model Identification. Part No. D1662

Transcription

1 Washer-Extractor Refer to Page 4 for Model Identification Parts Part No. D April 2015

2

3 PARTS ORDERING INFORMATION If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laundry Systems at +1(920) for the name and address of the nearest authorized parts distributor. For technical assistance, call either of the num-bers listed below: (920) Ripon, Wisconsin Wevelgem, Belgium NAMEPLATE LOCATION When calling or writing about your product, be sure to mention model and serial numbers, which are located on the machine's nameplate TABLE OF CONTENTS Frame and tub support Cabinet Control panel with coin meter Control panel without coin meter Coin vault system Soap hopper, top cover D... Drain pump, drain valve Rear panel Drive D... Tub and drum Door A... Trunnion 6kg / 15lb B... Trunnion 7,5kg / 18lb D1662 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 3

4 MODEL IDENTIFICATION Information in this manual is applicable to these models: C6 LAC60 CW7 C8 LAC75 CW8 4 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT D1662

5 D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 5

6 FRAME AND TUB SUPPORT D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 6

7 2 SP Frame, 6 kg/15lbs 2 SP Frame, 7,5 kg/18lbs 3 SP Bed complete, 6 kg/15lbs 3 SP Bed complete, 7,5 kg/18lbs 4 SP Front flange 5 SP Rear flange 6 SPPRI Adjustable leg 7 SPPRI Cable passage 8 SP Upper weight 9 SP Lower weight 10 SP Damper 12 SPPRI Spring sleeve 13 SP Vibration limiter 14 SP Air trap holder 16 SP Nut M4 17 SP Nut M5 18 SP Nut M10 19 SP Screwing 20 SP Nut M20 22 SP Bolt M4x12 23 SPPRI Bolt M5x12 24 SP Bolt M10x30 25 SP Bolt M10x50 26 SP Bolt M10x SP Washer 4 28 SP Washer SP Washer SP Washer SP Washer 10 Frame and tub support: drawing nr D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 7

8 CABINET D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 8

9 1 SP Cabinet shell, applicable for coinmeter 1 SP Cabinet shell, not applicable for coinmeter 2 SP Cabinet 3 SP Rear panel, 6 kg/15lbs 3 SP Rear panel, 7,5 kg/18lbs 5 SP Plug 6 SPPRI Spring sleeve 7 SPPRI Spring 8 SPPRI Microswitch 9 SPPRI Springs holder plastic 10 SPPRI Spring 15mm 11 SPPRI Spring 99mm 12 SP Vibration switch holder 13 SPPRI Doorlock 14 SP Draw-bar for emergency opening 15 SP Silon washer 16 SPPRI Elbow 17 SP Bolt M6x16 19 SP Bolt M3x25 20 SP Bolt M4x8 21 SP Nut M3 22 SP Nut M6 23 SPPRI Hose clamp 24 SP Washer 6 25 SP Washer 6 26 SP Washer 3 27 SP Bolt M4x16 28 SP Washer 12x4,33x1 29 SP Washer 4 30 SP Nut M4 32 SP Washer 4 33 SP Washer M4 34 SPPRI Venting hose 35 SP Complete angle I 36 SP Complete angle II 37 SP Microswitch holder 40 SP Bolt M6x10 Cabinet: drawing nr D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 9

10 CONTROL PANEL WITH COIN METER D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 10

11 1 SP Keyboard 2 SP Programmer board 3 SP Memory 4 - Coin meter (according on order) 5 SP Washer 3 6 SP Bolt M3x6 - - Insert label (according to the language version, not shown) Control panel with coin meter: drawing nr D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 11

12 CONTROL PANEL WITHOUT COIN METER D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 12

13 1 SP Keyboard 2 SP Programmer board 3 SP Memory 4 SP Button ON/OFF 5 SPPRI Cover 6 SP Label switcher 7 SP Washer 3 8 SP Bolt M3x6 - - Insert label (according to the language version, not shown) Control panel without coin meter: drawing nr D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 13

14 COIN METER SYSTEM D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 14

15 4 SPR07A Cam for lock coin box 5 SP Washer M6 8 SPR07A Indicator disc timer 9 SP Plastic box 10 SP Ornamental plate coin vault 12 SP Coin vault PVC 13 SPPRI Coin vault lock 23 SP Holder of coinmeter 24 SP Washer with external teeth M6 25 SP Washer 6,4 27 SP Bolt M4x8 28 SP Washer with external teeth M4 32 SP Washer 4,3 35 SP Bolt M6x16 38 SPPRI Securing washer 39 SPPRI Securing nut small 40 SPPRI Supple bent washer 41 SPPRI Securing nut big 44 - Not on your model Coin meter system: drawing nr D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 15

16 SOAP HOPPER, TOP COVER D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 16

17 1 SP Top cover 2 SPPRI Rubber cover soap hopper 3 SPF Lath for rubber cover hopper 10 SPPRI Bolt M4x12 11 SP Nut M4 13 SPPRI Soaphopper sealing 14 SPPRI Outer part soap hopper 15 SPPRI Inner part soap hopper 16 SPPRI Syphon part last rinse 17 SPPRI Box last rinse 18 SPPRI Protection plate 19 SPPRI Drawer prewash 20 SPPRI Drawer main wash 21 SPPRI Insertion piece last rinse 22 SPPRI Screw 3,5x9,5 23 SP Bolt M6x20 24 SP Bolt M6x Not on your model 26 SP Washer M6 27 SPPRI Bolt M6x16 33 SP Label "Service warning" 33 SP Label "Transporting braces" 34 SPPRI Screw 2,2x6, Not on your model 40 SPPRI T-part 42 SP Plug 44 SPPRI Air vent-soaphopper hose 45 SP Rubber soap hopper-tub 46 SPPRI Hose 49 SP Inlet hose 50 SP Plug 51 SPPRI Hose clamp 52 SPPRI Hose clamp 53 SPPRI Hose clamp 54 SPPRI Hose clamp 57 SP Washer M6 58 SP Washer M6 59 SP Nut M6 Soap hopper, top cover: drawing nr D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 17

18 DRAIN PUMP, DRAIN VALVE D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 18

19 1 SPPRI Pump 2 SPPRI Connecting hose drum-pump 3 SPPRI Hose of the air trap 4 SPPRI Water level switch hose 5 SPPRI Reduction 7 SPPRI Hose clamp 8 SPPRI Hose clamp 9 SPPRI Hose clamp 10 SPPRI Hose clamp 11 SP Binding belt 12 SP Bolt M6x16 13 SP Washer 6 14 SP Washer 6 15 SPPRI Drain hose for pump 16 SP Bolt M8x10 19 SPPRI Foam ring 20 SPPRI Cable passage 21 SP Binding belt holder 22 SP Reinforcement tube 23 SP Binding belt 24 SP Pump cover 25 SP Foam cylinder 26 SP Hose of drain valve 27 SP Reinforcement tube 28 SPPRI Hose clamp 30 SP Plug 31 SPPRI Hose clamp 32 SP Drain valve 2 33 SP Bolt M6x20 34 SP Nut M6 - SPPRI Drain hose for drain valve (not shown) Drain pump, drain valve: drawing nr D D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 19

20 REAR PANEL D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 20

21 1 SP Rear panel 2 SPPRI Three way valve 220V 3 SPPRI Two way valve 220V 4 SP Heating contactor 4 SP Heating contactor 9kW, 220V 5 SPPRI Terminal board 6 SPPRI poles connector 7 SPPRI Isolation paper 8 SPPRI Fuse sleeve 8 SPPRI Fuse sleeve 9 SPPRI Fuse 6,3A 9 SP Fuse 4A/500V 9 SP Fuse T1A/250V 10 SPPRI Swivel 11 SPPRI Swivel nut 12 SP Plastic box 13 SP Terminal board 14 SP Cable bushing M16 15 SP Bolt M6x25 16 SP Bolt M4x10 17 SP Bolt M4x16 19 SP Cable bushing nut M16 20 SP Nut M6 21 SP Washer 4 22 SP Nut M4 24 SP Washer 6 26 SP Bolt M4x16 27 SP Washer 4 28 SP Washer 4 29 SP Wall connection 6 hoses 30 SP Plate with thread 31 SP Sticker Hot water 32 SP Sticker Cold water 33 SP Hose plug SP Sticker Fuse 6,3A 34 SP Sticker Fuse 4A/500V 35 SPPRI Hose d10/14 36 SPPRI Earth plate 37 SPPRI Sticker PE 38 SPPRI Sticker L1, L2, L3 - SP Binding belt holder (not on the picture) 40 SP Plug 41 SP Inlet hose 42 SPPRI Sealing 45 SP Filter 47 SPPRI Serial label 48 SP Transparent foil self-adhesive 50 SP Clip d15, SP Clip d18,5-19,5 52 SP Screw M4x13 55 SP Cable bushing - SPPRI Valve filter (not shown) Rear panel: drawing nr D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 21

22 DRIVE D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 22

23 1 SP Motor 2 SP Motor sleeve 3 SP Drum pulley 4 SP Belt 5 SP Bolt M10x30 6 SP Bolt 5/16 x 11/4 7 SP Washer 8 8 SP Washer 8 9 SP Plastic washer 10 SP Plastic washer 11 SP Distance case, 6 kg/15lbs 11 SP Distance case, 7,5 kg/18lbs 12 SP Frequency converter 13 SP Frequency converter holder 14 SP Bolt M4x16 15 SP Washer 4 16 SP Nut M4 21 SP Washer 10 - SP Communication cable (not shown) - SP Main wiring (not shown) - SP Motor wiring (not shown) Drive: drawing nr D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 23

24 TUB AND DRUM D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 24

25 1 SP Wash drum complete, 6 kg/15lbs 1 SP Wash drum complete, 7,5 kg/18lbs 2 SP Tub complete, 6 kg/15lbs 2 SP Tub complete, 7,5 kg/18lbs 3 SP Springs holder right 4 SP Springs holder left 5 SP Distance bushing 6 SP Motor holder 7 SP Wiring holder 8 SPR Ring 12 holes, 6 kg/15lbs 8 SPPRI Ring 24 holes, 7,5 kg/18lbs 10 SPPRI Rear panel of tub, 6 kg/15lbs 10 SP Rear panel of tub, 7,5 kg/18lbs 11 SPPRI Sealing of tub, 6 kg/15lbs 11 SPPRI Sealing of tub, 7,5 kg/18lbs 12 SP Rubber tub housing 13 SPPRI Clip 14 SPPRI Temperature sensor 15 SPPRI Sleeve spring 16 SPPRI Temperature sensor holder 17 SPPRI Temperature sensor holder nut 18 SPPRI Bushing washer 20 SP Bolt M8x70 21 SP Bolt M8x35 22 SP Bolt M8x70 23 SP Bolt M8x40 24 SP Bolt M8x60 25 SP Nut M8 26 SP Nut M8 31 SP Washer 8 32 SP Heating element 2000W 32 SP Heating element 2750W 32 SP Heating element 3000W, l=265mm 33 SPPRI Plug heating element opening Tub and drum: drawing nr D D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 25

26 DOOR D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 26

27 2 SP Door hinge complete 3 SP Door 4 SP Door reinforcement 5 SP Catch washer 6 SPPRI Door glass 7 SPPRI Door sealing 8 SPPRI Door catch 9 SPPRI Door hinge block 10 SP Washer door catch 11 SPPRI Bolt M6x20, applicable for round and square door 12 SP Shim 13 SPPRI Dimension washer 14 SP Nut M6 15 SP Washer 16 SP Bolt M6x16 17 SP Bolt M6x16 18 SP Washer 6 19 SP Washer 6 20 SP Bolt M6x25 - SP Glue for sticking the bolts - pos. 11, 20 (not shown) Door: drawing nr D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 27

28 TRUNNION 6kg / 15lb D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 28

29 1 SP Bearing house 2 SP Spoke complete 3 SPPRI Bearing 4 SPPRI Bearing 5 SPPRI Axial seal 6 SPPRI Counter ring 8 SP Bolt M8x35 9 SP Bolt M10x35 10 SPPRI Washer 22x10x1 11 SP Washer SP Washer M10 13 SP Washer SP Nut M10 15 SP Nut M8 16 SP Bolt M12x35 - SP Bearing house complete - SP Bearing Loctite 603 for sticking the bearing - pos. 3, 4 (not shown) Trunnion 6kg / 15lb: drawing nr A D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 29

30 TRUNNION 7,5kg / 18lb D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 30

31 1 SP Bearing house 2 SP Spoke complete 3 SP Bearing 4 SP Bearing 5 SP Distance ring 6 SPPRI Axial sealing 7 SPPRI Shaft ring 8 SP Bolt M8x35 9 SP Bolt M10x35 10 SPPRI Washer 22x11x3 11 SP Washer SP Bolt M12x35 13 SP Washer SP Washer SP Nut M10 16 SP Nut M8 - SP Bearing house complete - SP Bearing Loctite 603 for sticking the bearing - pos. 3, 4 (not shown) Trunnion 7,5kg / 18lb: drawing nr B D1661 Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 31

32