EC 6-295P220S001. smart guide 2 OPERATION. 2.1 How to turn the instrument ON/OFF. If you have to turn the instrument ON/OFF:

Transcription

1 EC 6-295P220S001 smart guide ON-OFF digital controller for ventilated refrigerating units Version 1.01 of 15 th March 2005 File ec6295p220s001_eng_v1.01.pdf PT EVCO S.r.l. Via Mezzaterra 6, Sedico Belluno ITALY Phone Fax ENGLISH 1 PREPARATIONS 1.1 How to install the instrument On DIN rail (it is not supplied by the builder). 2 OPERATION 2.1 How to turn the instrument ON/OFF If you have to turn the instrument ON/OFF: for 2 s During the normal operation the instrument shows the cabinet temperature. 2.2 How to silence the buzzer If you have to silence the buzzer: 2.3 How to activate the defrost by hand If you have to activate the defrost by hand: for 4 s Unless the evaporator temperature is below the defrost end temperature you have set with the parameter d2, the defrost will not be activated. 2.4 How to turn the cabinet light ON/OFF If you have to turn the cabinet light ON/OFF: 2.5 Compressor thermal protection The activation of this input forces the compressor OFF by hardware and software. 3 REAL TIME CLOCK 3.1 How to set the clock Press for 2 s : the instrument Press or for selecting If you have to modify the value of the hour: and or If you have to modify the value of the minutes: release and press it again during the modification of the hour, then... Evco S.r.l. EC P220 S001 Sheet 1/3 DIN rail installation (it is not supplied by the builder). or If you have to quit the procedure: or as long as the instrument shows the cabinet temperature or do not operate for about 30 s.

2 4 WORKING SETPOINT 4.1 How to set the working setpoint If you have to modify the working setpoint value: and or (1) (2) (1) you can set the working setpoint between the limits you have set with the parameters r1 and r2 (2) unless the parameter r5 has value 0, you can not modify the working setpoint. 5 CONFIGURATION PARAMETERS 5.1 How to set the configuration parameters Configuration parameters are arranged on two levels. If you have to gain access the first level: and for 4 s : the instrument If you have to select a parameter: or If you have to modify the value of the parameter: and or If you have to gain access the second level: gain access the first level or for selecting and or for setting -19 and for 4 s : the instrument If you have to quit the procedure: and for 4 s or do not operate for about 60 s. 6.2 Evaporator temperature showing If you have to show the evaporator temperature: or for selecting 6.3 Temperature storage If you have to show the temperature the instrument has stored during the lower temperature : or for selecting (3) If you have to show the temperature the instrument has stored during the upper temperature : or for selecting (4) If you have to erase the temperature the instrument has stored during the lower or upper temperature : or for selecting or for 4 s : the instrument (3) unless the parameter A8 has value 1 or 3, the label AL will not be showed (4) unless the parameter A8 has value 2 or 3, the label AH will not be showed. 7 SIGNALS 7.1 Signals (16) do not set more instruments as master (17) the time between the master implements a control and the slave implements the same control is n1 x n4 (18) except the control turning ON and OFF; it will immediately be implemented (19) if among the remote controls the slave has to implement there is the defrost activation, the parameter d5 will set a time you will have to add to the one you have set with the parameters n1 and n4 (the slave will implement the control even if the conditions will not allow the master of activating the defrost); if the master is in the STAND-BY mode and among the remote controls the slave has to implement there is not the turning ON and OFF, the slave will work with the local settings. 11 ELECTRICAL CONNECTION 11.1 Electrical connection 6 ADDITIONAL FUNCTIONS 6.1 How to gain access the additional functions LED Compressor LED MEANING If you have to gain access the additional functions: for 2 s : the instrument If you have to quit the procedure: or as long as the instrument shows the cabinet temperature or do not operate for about 30 s. if it is lighted, the compressor will be ON if it flashes, a compressor delay will be running (look at the parameters C0, C1, C2, C4, n1 and n4) Defrost LED if it is lighted, the defrost output will be activated if it flashes: a defrost delay will be running (look at the parameters C0, C1, C2, C4, n1 and n4) (20) short-circuit terminals 1 and 5 and/or 1 and 7 if you do not use the lock input and/or the compressor thermal protection (21) the position of the probe for compressor thermal protection could compromise the insulation between low voltage and high voltage parts. the dripping will be running (look at the parameter d7) the freezing fluid heating will be running (look at the parameter dp)

3 na remote control the slave has to implement (0 = no controls, 1 and 9 = compressor status, Evaporator fan LED 8 ALARMS 2 and 10 = defrost activation, 3 and 11 = compressor status and defrost activation, if it is lighted, the evaporator fan will be ON 8.1 Alarms 4 and 12 = turning ON and OFF, 5 and 13 = compressor status and turning ON and OFF, if it flashes, the after dripping evaporator fan delay will be running (look CODE REASONS REMEDIES EFFECTS 6 and 14 = defrost activation and turning ON and OFF, 7 and 15 = compressor status, at the parameter F5) there is the corruption switch off the power you can not gain defrost activation and turning ON and OFF, 8 = reserved) (19) Cabinet light LED corrupted of the configuration supply of the instru- access the setting if it is lighted, the cabinet light will be ON memory data of the memory of ment: unless the procedures LABEL MIN. MAX. U.M. DEF. ENERGY SAVING (the working setpoint becomes r8) if it flashes, the multifunction input will be active (look at the parameters data the instrument disappears, you will all outputs will be Hr h.damin (6) 0.0 Energy Saving cycle activation time i0, i1 and i7) have to change the forced OFF Hr h.damin (6) 0.0 Energy Saving cycle length Lock input/thermal protection LED instrument if it is lighted, there will have been a number of lock input/thermal pro- the lock input/thermal deactivate the inputs the compressor will LABEL MIN. MAX. U.M. DEF. REAL TIME DEFROST tection s such as to give the lock of the instrument (turn the instru- person protection and the (look at the param- be forced OFF Hd h.damin (6) first defrost activation time (it is important if de = 3; = it will never be activated) (7) ment OFF and turn it ON again, look at the parameters i2, i3, i4 and i5) into the multifunction input are eters i0, i1, i2, i3, i4 if the defrost is run- Hd h.damin (6) second defrost activation time (it is important if de = 3; = it will never be activated) (7) if it flashes, the lock input/thermal protection will be active (look at the cabinet active and i5) ning, it will immedi- Hd h.damin (6) third defrost activation time (it is important if de = 3; = it will never be activated) (7) parameters i2, i3, i4 and i5) (you can turn the instrument ately end Hd h.damin (6) fourth defrost activation time (it is important if de = 3; = it will never be activated) (7) ON STAND-BY LED not OFF and turn it ON the defrost will Hd h.damin (6) fifth defrost activation time (it is important if de = 3; = it will never be activated) (7) if it is lighted, the instrument will be in the STAND-BY mode silence again never be activated Hd h.damin (6) sixth defrost activation time (it is important if de = 3; = it will never be activated) (7) if it flashes, the instrument will be set as slave but it will not be author- the you will get the ac- (5) the unit of measure depends on the parameter /8 ized to implement the remote controls coming from the master (look at buzzer) tion you have cho- (6) damin = 10 minutes the parameter n3) sen with the param- (7) unless the evaporator temperature is below the defrost end temperature you have set with the parameter d2, the defrost will not be activated if it flashes every two seconds, the instrument will be set as slave and eter i0 (8) if the time the compressor is ON is lower than 30 s, the compressor will never be ON; if the cabinet probe failure takes place during a compressor delay, the compressor will be among the remote controls, coming from the master, the slave has to the lock input/thermal deactivate the input the compressor will forced OFF for 1 min; the parameter C1 sets the minimum delay between the end of the cabinet probe failure and the following activation of the compressor (if the parameter implement, there will be the turning ON and OFF (look at the param- lock protection is active. (look at the param- be forced OFF C1 has value 0, the compressor will be forced off for 2 min) eter na) input/ If there has been a eters i2, i3, i4 and i5) if the defrost is run- (9) if at the moment of the defrost activation the cabinet temperature is below the value working setpoint + r0, the instrument will not show temperatures above that value; if thermal number of lock input/ turn the instrument ning, it will immedi- at the moment of the defrost activation the cabinet temperature is above the value working setpoint + r0, the instrument will not show the increases of the temperature (if INDICAT. MEANING protection thermal protection OFF and turn it ON ately end the increase takes place below the value working setpoint + r0, look at the previous case); the instrument restores the normal operation once the after dripping evaporator the instrument will be set as slave and among the remote controls, com- s such as to give again the defrost will fan delay ends and the cabinet temperature falls below the freeze temperature ing from the master, the slave has to implement, there will be the com- the lock of the instru- never be activated (10) if at the moment of the defrost activation the compressor is ON since a time lower than the one you have set with the parameter, the compressor will be forced ON for a time pressor status (look at the parameter na). ment, for 3 s such as to finish the time you have set with the parameter If you have to show the cabinet temperature, press every 4 (if you (11) if the lower temperature takes place during the count of the delay, this last will be cleared the instrument will be set as slave, among the remote controls, coming have to restore the (12) if the temperature does not disappear at the end of the times you have set with the parameters A3 and AA, it will further be excluded for the time you have set with the every 2 s from the master, the slave has to implement, there will be the compres- normal operation, turn parameter A6; if the temperature takes place during the defrost and does not disappear at the end of the time you have set with the parameter A7, it will further be sor status but there will not be the turning ON and OFF, both the master the instrument OFF excluded for the time you have set with the parameter A6; if the temperature takes place during the multifunction input activation, it will be excluded for the time "A5 + A6" since the input activation or for the time you have set with the parameter A6 since the input deactivation (13) the evaporator fan stop temperature is cabinet temperature - F1 ; you always have to consider the parameter F1 with positive sign (14) the instrument will automatically verify the maximum value of the parameter; it always has to be lower than the value you have set with the parameter i4 (15) when there is 1 min to the end of the time you have set with the parameter, the cabinet light will be turned OFF just for 1 s; press during the time you have set with the parameter to turn the cabinet light ON and to exclude the function, press again before the end of the time you have set with the parameter to recover the function (if the remaining time of the parameter is higher than 1 min, the time will be forced at 1 min and the cabinet light will be turned OFF just for 1 s) Evco S.r.l. EC P220 S001 Sheet 2/3 and the slave will be in the STAND-BY mode (look at the parameter na). If the master is in the STAND-BY mode and the slave is ON, the indication will be showed alternated with the cabinet temperature cabinet probe and turn it ON again) the kind of cabinet probe you have connected is not right the cabinet probe plays up look at the parameter /0 test the integrity of the probe test the instrumentprobe connection the compressor will work in accordance with the parameters C5 and C6

4 the connection in- test the temperature if the defrost is run- there has been an up- look at the parameters LABEL MIN. MAX. U.M. DEF. DIGITAL INPUTS strument-cabinet close to the probe (it ning, it will immedi- for 3 s per temperature A0, A1b, A2b, A8 and i action given by the multifunction input activation (0 = inactive, 1 = once d5 has passed, the probe is wrong has to be between ately end every 4 A9 defrost will be activated (7), 2 = the cabinet light will be turned ON, 3 = the compressor will be the cabinet tempera- the limits allowed by the defrost will forced ON for A5 and the cabinet light will be turned ON, 4 = the compressor and the ture is outside the the working range) never be activated evaporator fan will be forced OFF for A5 and the cabinet light will be turned ON, limits allowed by the the cabinet tempera- test the temperature 5 = the evaporator fan will be forced OFF for A5 and the cabinet light will be turned ON, working range of lower ture is outside the limit close to the probe 6 = the working setpoint becomes r8, 7 = the working setpoint becomes r8 and the cabinet the instrument tempera- you have set with the (look at the parameters light will be turned OFF); look at i7 as well the kind of evapora- look at the param- if the parameter de ture parameter A1A A0, A1A and A2A) i kind of contact of the multifunction input (it is important if i0 0; 0 = NO, 1 = NC) evapora- tor probe you have eter /0 has value 2, the in- there has been a lower look at the parameters i action given by the lock input/thermal protection activation (1 = the compressor will be forced tor probe connected is not test the integrity of strument will work for 3 s temperature A0, A1A, A2A, A8 and OFF, 2 = in accordance with i3, i4 and i5) right the probe as if the parameter every 4 A9 i lock input/thermal protection s number such as to give the lock of the instrument (it is the evaporator test the instrument- had value 0 important if i2 = 2; 0 = the lock of the instrument will never take place) probe plays up probe connection if the parameter F7 i4 i5 240 min 0 time without lock input/thermal protection s able to clear the lock input/thermal pro- the connection in- test the temperature has value 3 or 4, the there is the corruption set the clock again if the parameter de tection s counter (it is important if i2 = 2) strument-evaporator close to the probe (it evaporator fan will real time of the data of the clock has value 3, the in- i (14) min 0 minimum delay between the lock input/thermal protection deactivation and the following probe is wrong has to be between work in accordance clock of the instrument strument will work compressor activation (it is important if i2 = 2) the evaporator tem- the limits allowed by with the compres- as if the parameter i indication Ain flashing on the display during the multifunction input activation (it is impor- perature is outside the working range) sor, except what had value 0 tant if i0 0) the limits allowed by you have set with the Energy Saving i min 0 delay between the multifunction input deactivation and the cabinet light gets OFF (it is the working range the parameters F4 cycle will never be important if i0 = 2, 3, 4 or 5) (15) of the instrument and F5 activated the defrost will end the instrument will be if you have to show look at the effects of LABEL MIN. MAX. U.M. DEF. SERIAL NETWORK (EVCOBUS) by time (parameter slave set as slave, among the code, that case L instrument address d3) the remote controls, press L instrument group the multifunction input deactivate the input you will get the action coming from the mas- look at the remedies L baud rate (0 = 1,200 baud, 1 = 2,400 baud, 2 = 4,800 baud, 3 = 9,600 baud) multi- is active. (look at the parameters you have chosen with ter, the slave has to of that case function Unless the parameter i0, i1 and i6) the parameter i0 implement there will input i6 has value 1, the in- be the comp. status strument will not show and there will be one any indication of the s you saw LABEL MIN. MAX. U.M. DEF. SERIAL NETWORK (EVCONET) the cabinet tempera- test the temperature in the previous cases. n operation of the instrument in the network (0 = instrument not enabled to work in the upper ture is outside the limit close to the probe If the master is in the network, 1 = master, 2 = slave) (16) tempera- you have set with the (look at the parameters STAND-BY mode and n address of the instrument in the network (it is important if n0 0; 0 = master address, ture parameter A1b A0, A1b and A2b) the slave is ON, the in = first... eighth slave address) dication will be n authorization to implement the remote controls coming from the master (it is important if showed every 2 s alter- n0 = 2 and n1 0; 1 = YES) nated with the n s 0 time between the master implements a control and the slave implements the same control (it code (17) (18) is important if n0 = 2 and n1 0); look at na as well

5 LABEL MIN. MAX. U.M. DEF. ALARMS A C/ F (5) 2.0 hysteresis (differential, it is relative to A1A and A1b, it is important if A2A and/or A2b 0) the value of the pa- look at the param- the instrument will relay working in accordance with the instrument mode (the relay will be activated if the serial rameters n0, n1 and eters n0, n1 and n3 work with the local instrument is ON and it will be deactivated if the instrument is in the STAND-BY mode, A1A C/ F (5) -10 lower temperature threshold; look at A2A as well A2A kind of lower temperature (0 = it will never be activated, 1 = lower temperature relative to the working setpoint, 2 = absolute lower temperature ) A1b C/ F (5) 10.0 upper temperature threshold; look at A2b as well network n3 is wrong test the connections settings change-over contact). the connections of of the instrument Kind of defrost: electric and hot gas defrost. the instrument are Defrost control: defrost interval, defrost end temperature, defrost maximum length wrong and defrost interval count mode (automatic, by hand and remote). A2b kind of upper temperature (0 = it will never be activated, 1 = upper temperature relative to the working setpoint, 2 = absolute upper temperature ) A min 120 upper temperature exclusion time since you turn the instrument ON (it is important if A2b 0) (11) A min 30 buzzer exclusion time since the multifunction input activation (it is important if i0 0; -1 = the buzzer will never be activated) A min 5 temperature exclusion time (it is important if A2A and/or A2b 0) (12) A min 15 upper temperature exclusion time since the end of the after dripping evaporator fan delay (since the end of F5, it is important if A2b 0) (11) A kind of temperature the instrument has to store (it is important if A2A and/or A2b 0; 0 = it will never be stored, 1 = lower temperature, 2 = upper temperature, 3 = both the lower temperature and the upper one) A s 1 time between two records of the temperature in succession (it is important if A2A and/or A2b 0 and A8 0) AA min 0 temperature s relative to the working setpoint exclusion time since the multifunction input activation/deactivation (it is important if i0 = 6 or 7) and since the activation/end of the Energy Saving cycle The instrument shows the indications above alternated with the cabinet temperature, except the indication E2 (it flashes), E0 (it is alternated with the indication ) and net (slave, it is a fixed indication) and the buzzer utters an intermittent beep. 9 TECHNICAL DATA 9.1 Technical data Box: self-extinguishing grey. Size: 106 x 90 x 58 mm (4.17 x 3.54 x 2.28 in, 6 DIN modules). Installation: on DIN rail (it is not supplied by the builder). Frontal protection: IP 40. Connections: screw terminal blocks with pitch 5 mm (0.19 in) for cables up to 2.5 mm² (0.38 sq in, power supply, inputs and outputs), 5 poles single line female connector with pitch 2.5 mm (0.09 in, serial port). Ambient temperature: from 0 to 55 C (32 to 131 F, % of relative humidity without condensate). Power supply: 230 Vac, 50/60 Hz, 4 VA. Clock data maintenance without power supply: 24 hours (the instrument must Serial port: TTL with EVCOBUS communication protocol, adapt for serial interface EC IFC 02. have been ON for 2 min at least). LABEL MIN. MAX. U.M. DEF. EVAPORATOR FAN F C/ F (5) -1.0 evaporator fan stop temperature (evaporator temperature, it is important if F7 = 3 or 4); look at F6 as well F C/ F (5) 2.0 hysteresis (differential, it is relative to F1, it is important if F7 = 3 or 4) F evaporator fan action during the defrost and dripping (0 = it will be forced OFF, 1 = it will be forced ON, 2 = it will work in accordance with F7) F min 2 after dripping evaporator fan delay Alarm buzzer: included. Measure inputs: 2 (cabinet and evaporator probe) for PTC or NTC probes. Digital inputs: 2 inputs: one multifunction input (NO or NC contact) and one lock input, without voltage (they work with 5 ma). Working range: from -50 to 99.9 C (-58 to 212 F) for PTC probe, from -40 to 99.9 C (-40 to 212 F) for NTC probe. Setpoint range: from -99 to 99.9 C (-99 to 99 F). Resolution: 1 F with unit of measure in Fahrenheit, 0.1 or 1 C with unit of measure F kind of evaporator fan stop temperature (it is important if F7 = 3 or 4; 0 = absolute evaporator fan stop temperature, 1 = evaporator fan stop temperature relative to the cabinet temperature) F evaporator fan action during the normal operation (0 = it will be forced OFF, 1 = it will be forced ON, 2 = it will work in accordance with the compressor, 3 = it will work in accordance with F1 and F2, 4 = if the compressor is ON, it will work in accordance with F1 and F2, if the compressor is OFF, it will be forced OFF) Evco S.r.l. EC P220 S001 Sheet 3/3 in Celsius. Display: one red LED 3-digit display 13.2 mm (0.51 in) high, output status indicators, instrument mode indicator. Outputs: 5 relays: one Vac relay for one 1½ 230 Vac compressor control (NO contact), one Vac relay for evaporator fan control (NO contact), one Vac relay for defrost system control (change-over contact), one Vac relay for cabinet light control (NO contact) and one Vac

6 10 WORKING SETPOINT AND CONFIGURATION PARAMETERS 10.1 Working setpoint LABEL MIN. MAX. U.M. DEF. WORKING SETPOINT r1 r2 C/ F (5) 0.0 working setpoint 10.2 First level parameters LABEL MIN. MAX. U.M. DEF. PASSWORD LABEL MIN. MAX. U.M. DEF. REGULATOR r C/ F (5) 2.0 hysteresis (differential, it is relative to the working setpoint) r1-99 r2 C/ F (5) -50 minimum value you can assign to the working setpoint r2 r C/ F (5) 50.0 maximum value you can assign to the working setpoint r working setpoint modification lock-out (1 = YES) r C/ F (5) 0.0 auxiliary working setpoint (it is the working setpoint during the multifunction input activation if i0 = 6 or 7 and during the Energy Saving cycle) PA password LABEL MIN. MAX. U.M. DEF. COMPRESSOR PROTECTION LABEL MIN. MAX. U.M. DEF. MEASURE INPUTS /1A C/ F (5) 0.0 cabinet probe calibration /1b C/ F (5) 0.0 evaporator probe calibration LABEL MIN. MAX. U.M. DEF. REGULATOR r C/ F (5) 2.0 hysteresis (differential, it is relative to the working setpoint) C min 0 minimum delay between you turn the instrument ON and the first compressor activation C min 5 minimum delay between two compressor activation in succession C min 3 minimum delay between the compressor gets OFF and the following activation C fixed delay since the compressor gets ON and OFF (1 = YES, for 3 s) C min 10 cycle time for the compressor activation during the cabinet probe C % 50 percentage of C5 the compressor is ON during the cabinet probe failure (8) LABEL MIN. MAX. U.M. DEF. SERIAL NETWORK (EVCONET) n authorization to implement the remote controls coming from the master (it is important if n0 = 2 and n1 0; 1 = YES) LABEL MIN. MAX. U.M. DEF. ENERGY SAVING (the working setpoint becomes r8) Hr h.damin (6) 0.0 Energy Saving cycle activation time Hr h.damin (6) 0.0 Energy Saving cycle length LABEL MIN. MAX. U.M. DEF. REAL TIME DEFROST Hd h.damin (6) first defrost activation time (it is important if de = 3; = it will never be activated) (7) Hd h.damin (6) second defrost activation time (it is important if de = 3; = it will never be activated) (7) Hd h.damin (6) third defrost activation time (it is important if de = 3; = it will never be activated) (7) Hd h.damin (6) fourth defrost activation time (it is important if de = 3; = it will never be activated) (7) Hd h.damin (6) fifth defrost activation time (it is important if de = 3; = it will never be activated) (7) Hd h.damin (6) sixth defrost activation time (it is important if de = 3; = it will never be activated) (7) 10.3 Second level parameters LABEL MIN. MAX. U.M. DEF. MEASURE INPUTS / kind of probe (1 = PTC, 3 = NTC) /1A C/ F (5) 0.0 cabinet probe calibration /1b C/ F (5) 0.0 evaporator probe calibration / temperature resolution (it is important if /8 = 1; 0 = 1 degree, 1 = 0.1 degrees) LABEL MIN. MAX. U.M. DEF. DEFROST d h 8 defrost interval (it is important if de 3); look at de as well (7) (0 = the defrost will never automatically be activated) d kind of defrost (0 = electric defrost, 1 = hot gas defrost) d C/ F (5) 2.0 defrost end temperature (evaporator temperature) d min 30 defrost maximum length (0 = the defrost will never be activated) d defrost activation every time you turn the instrument ON (1 = YES) (7) d min 0 delay between you turn the instrument ON and the defrost activation (it is important if d4 = 1) d freeze of the temperature showed by the instrument during the defrost (1 = YES) (9) d min 2 dripping time d compressor protections cleaning at the moment of the defrost activation (it is important if d1 = 1; 1 = YES) de defrost interval count mode; look at d0 as well (0 = the instrument counts the working time, 1 = the instrument counts the sum of the times the compressor is ON, 2 = the instrument counts the sum of the times the evaporator temperature is below df, 3 = real time defrost, the defrost will be activated at the times you have set with the parameters Hd1... Hd6) df C/ F (5) 0.0 defrost interval count freeze threshold (evaporator temperature, it is important if de = 2) dp 0 99 min 0 minimum time the compressor must have been ON at the moment of the defrost activation in order that the defrost can be activated (it is important if d1 = 1) (10) / temperature unit of measure (0 = Fahrenheit degree, 1 = Celsius degree)