ISSY GLIDE VANITY UNIT

Transcription

1 page 1 of 6 FEATURES Basin Type One Piece Intergrated Top and Basin Basin Configuration Left Hand Basin or Right Hand Basin Door/Drawer Design Push to Open or Sensor (powered) Number of Drawers Taphole Configuration 0 or 1 Taphole Mounting Wall Hung White Only Solid Surface Moulded Top And Basin Features Movable Solid Surface Drawer Divider Removable and Washable Non Slip Drawer Mat Choice of Metallic Colours Option of Sensor Powered Drawers Solid Surface Moulded Waste Cut Out in Basin Drawer Custom Sizes A Range of Customised Sizes Available 1 Drawer 2 Drawer 2 Drawer 4 Drawer SPECIFICATIONS Height mm 320mm For Glide 750, 1200 and 0 For Glide 1750 (double basin) Width 500mm Length 750mm, 1200mm, 0mm (single basin) or 1750mm (double basin) Other Size Options 750 Single Drawer Can Be Customised 751-0mm Drawer Can Be Customised mm 0 2 Drawer Can Be Customised mm Drawer, Double Basin Can Be Customised mm Colour Variations Satin or Gloss (White) Metallic Silver Gloss or Metallic Charcoal Gloss Oak drawer fronts with matte clear finish, satin white base and end panels Fixing Bolted / Screwed to Wall by a Licensed Trades Person Vanity Unit Material 2 Pack Polyurethane on HMR MDF To see the complete range go to CLEANING RECommENDATIoNs Open Sky Design vanity tops are a high grade acrylic Solid Surface with a semi gloss finish. It is recommended that this Solid Surface top is protected during installation. Your vanity should be cleaned with a mild, non acidic, non abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft damp cloth and towel dry. Always clean spills and water as they occur. The Solid Surface top should be cleaned using a soft damp cloth with warm water OR a non abrasive ammonia based household cleaner OR a dedicated counter top cleaner. The possibility of concentrated acidic ingredients present in some beauty and cleaning products may damage the surface if left for a long duration. Citrus or silicone based sprays or polishes should not be used. It is recommended that all spills are cleaned up as they occur. Abrasive cleaners should NOT be used on this semi gloss surface. Damage caused by any improper treatment is not covered by the product warranty. Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors. Tech Page Version 3

2 page 2 of 6 GLIDE GLIDE

3 page 3 of 6 GLIDE GLIDE 1750 DOUBLE BASIN

4 page 4 of 6 INSTALLATION INSTRUCTIONS Vanity should be installed by a qualified, licensed trades person. Vanity Fitting Instructions Prior to installation it is important to inspect the vanity to ensure no damage has occurred in transit. If damage has occurred, or a visible defect exists, do not proceed with installation and advise supplier immediately. No warranty claim for damage will be accepted if the vanity is installed. It is recommended that the Solid Surface Top is protected during installation. Please Note: Manufacturer will not be liable for the cost of installation or removal of the vanity and the warranty will be voided if damage occurred during or after installation. Remove drawers (refer to Drawer Installation and Adjustment Instructions) Mark base and back of the vanity for drilling to allow for plumbing pipes. Drill holes for pipes with appropriate size hole saws. Position vanity over pipes in correct position. It is recommended that the vanity sit on a length of aluminium angle securely fastened to the wall Check with spirit level that the vanity is completely level. Screw vanity to the wall through back of the vanity, ENSURING SCREWS ARE FIXED TO STUDS. Allow enough fixing points at the top and bottom of the back panel to sufficiently secure the unit to the wall. All edges where vanity top and cabinet meet wall and floor are to be properly sealed with bathroom grade silicone to prevent water penetration. Materials used in construction are water-resistant not waterproof. Care must be taken to dry any spillage or leakage of water which may gain access to the cabinet when fitting. Replace drawers (refer to Drawer Installation and Adjustment Instructions). Recommendation for Plumbing Waste should not be over tightened to avoid stress on basin and top. Plumbing and electrical setout instructions 1. Diagrams below show wall positions of 40mm waste pipe, hot and cold outlets (if required) and power cord outlet (if required). Please note diagrams show set outs for 750, 1200 and 0 left hand basin, for right hand basin use mirror opposite. 2. Use 40mm plug and waste, non overflow with 40mm Short Inlet P Trap (both not supplied) 3. For power cord positioning of custom sizes, contact manufacturer. 4. Plumbing set outs for customised sizes: same as for 750 set out same as for 1200 set out same as for 0 set out 5. For plumbing and electrical set outs of customised mm double basin contact manufacturer. 6. Sensor Powered Drawers A 1.6 mtr power cord extension is fitted to the vanity and extends out the back of the unit at the position shown in the diagram below. This power cord should be connected by a qualified electrician to a 240 volt power supply with an isolating switch. Please Note: Any electrical fault caused by water penetration inside the vanity is not covered by the product warranty 7. If using a basin mixer, hot and cold hoses should be bracketed to the side or back of the vanity so as not to impede operation of the drawer. Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference

5 page 5 of Key Power Cord Hot and Cold 40mm Waste Pipe Glide 750 Front Elevation PLEASE NOTE Diagrams show setouts for left hand basin. For right hand basin use mirror opposite Glide 1200 Front Elevation Glide 0 Front Elevation Glide 1750 Front Elevation

6 page 6 of 6 drawer installation and adjustment DRAWER INSTALLATION INSTRUCTIONS The Nova Pro Drawers can be installed or removed with just one movement. To install drawer 1. Fully extend runners 2. Place drawer on runners 3. Close drawer firmly until a double click is heard Ensure drawer is engaged to BOTH runners. See Refitting Drawers To remove drawer 4. Fully extend drawer 5. Hold drawer sides as above and firmly lift off runners TOOL-FREE SIDE ADJUSTMENT 1. Press the catch hooks 2 (left and right) to the back 2. Lift the front up lightly and slide over ribs. Adjustment range ± 1.5mm. HEIGHT ADJUSTMENT 1. Lightly loosen the screw 3 and adjust the front with the eccentric screw 4 into the desired height position 2. Tighten screw 3 Adjustment range ± 2mm. 3 4 TILT ADJUSTMENT OF FRONT Readily accessible tilt adjustment facility on the inside of the drawer side. The tilt adjustment is achieved by adjusting this screw located at the rear of the drawer. Note: Only available on 122mm drawer sides REFITTING DRAWERS It is important that the drawers are refitted correctly if removed for installation. If the drawer is not locked into the runner system at all four corners the drawer will not function correctly. Please follow the Install Instructions for fitting the drawer then check the drawer is correctly locked onto the runner by carrying out the following checks. 1. Fully extend the drawer. Use gentle upward pressure to determine if each back corner is locked onto the runner. If a corner has not locked on, remove the drawer and reinstall using the Drawer Install Instructions guide. 2. Fully extend the drawer. Apply gentle upward pressure to the front 2 corners to test both corners are locked onto the runners. Finally give a gentle pull forward on both sides. If the drawer is correctly locked onto the runners the drawer should not be able to pull forward past its full extension. If any corner is not locked onto the runner remove the drawer and reinstall using the Drawer Install Instructions provided. 2 2

7 7YEAR QUALITY GUARANTEE REECE PRODUCT QUALITY GUARANTEE Excludes Electicial see Page 2 Electrical Warranty You have purchased a quality product from Reece Pty Ltd ABN ( Reece ). This product is covered by a 7 year replacement product warranty and a 12 month warranty over spare parts and labour. 7 YEAR WARRANTY DOMESTIC USE This warranty covers faults in the product construction, material and assembly. Products which are within 7 years from the date of purchase, found upon inspection by an authorised Reece representative, to be defective in construction, material or assembly, will be repaired or exchanged with an equivalent product free of charge. Replaced items become Reece s property. All replacement products will be available for collection without charge to the customer at the nearest Reece branch to the customer s location, or elsewhere as agreed between the customer and Reece. Labour and Spare Parts The labour for the replacement of products and spare parts to which this warranty applies will be supplied by Reece or relevant supplier using licensed plumbers engaged by Reece or relevant supplier within 1 year from the date of purchase. Spare parts which are within 1 year from the date of purchase found upon inspection by an authorised Reece representative to be defective in construction, material or assembly, will be replaced free of charge. Warranty Conditions This warranty will apply only under all of the following conditions: The item has been installed by a licensed plumber The item has been installed for and subjected to domestic residential use only Failure is due to a fault in the manufacture of the product Proof of purchase (including the date of purchase) is provided The installation of the product is in accordance with the instructions provided This warranty does not include faults caused by: Unsuitable or improper use Incorrect installation or installation not in accordance with the instructions provided Installation or part installation by the purchaser or any person other than a LICENSED PLUMBER Normal wear and tear Inadequate or complete lack of maintenance Chemical, electrochemical or electrical influences Harsh detergents or abrasive cleaners used on product finishes 1 YEAR WARRANTY COMMERCIAL USE Commercial use is all use other than for normal domestic residential purposes, including use in non-business places as in public buildings, schools, sports centres and in establishments that contain private bathrooms with high frequency of use by many individuals, such as hotels, motels, retirement villages and hospitals. The Commercial warranty covers this product against manufacturing faults in the construction, material and assembly of both the finished products and any spare parts for a period of 1 year from the date of purchase. Products and spare parts which are found upon inspection by an authorised Reece representative to be defective in construction, material or assembly will be repaired or exchanged free of charge. Replaced items become Reece s property. The labour for the replacement of products and spare parts to which this warranty applies will be supplied by Reece or relevant supplier using licensed plumbers engaged by Reece or relevant supplier. The Warranty Conditions and exclusions which apply to the domestic use warranty also apply to this commercial warranty. EXCLUSIONS To the fullest extent permitted by law, Reece excludes all liability for damage or injury to any person, damage to any property, and any indirect consequential or other loss or damage. CLAIM PROCEDURE For all warranty queries customers are to contact the branch where the product was purchased. These details can be found on your purchase invoice. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. VAN.T1.7YR Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference Don t risk it, use a licensed plumber.

8 Electrical REECE PRODUCT QUALITY GUARANTEE You have purchased a quality product from Reece Pty Ltd ABN ( Reece ). This product is covered by a 2 year replacement product warranty and a 12 month warranty on spare parts. 2 YEAR WARRANTY DOMESTIC USE This warranty covers faults in the product construction, material and assembly. Products which are within 2 years from the date of purchase, found upon inspection by an authorised Reece representative, to be defective in construction, material or assembly, will be repaired or exchanged with an equivalent product free of charge. Replaced items become Reece s property. All replacement products will be available for collection without charge to the customer at the nearest Reece branch to the customer s location, or elsewhere as agreed between the customer and Reece. 2YEAR QUALITY GUARANTEE 1 YEAR WARRANTY COMMERCIAL USE Commercial use is all use other than for normal domestic residential purposes, including use in non-business places as in public buildings, schools, sports centres and in establishments that contain private bathrooms with high frequency of use by many individuals, such as hotels, motels, retirement villages and hospitals. The Commercial warranty covers this product against manufacturing faults in the construction, material and assembly of both the finished products and any spare parts for a period of 1 year from the date of purchase. Products and spare parts which are found upon inspection by an authorised Reece representative to be defective in construction, material or assembly will be repaired or exchanged free of charge. Replaced items become Reece s property. The Warranty Conditions and exclusions which apply to the domestic use warranty also apply to this commercial warranty. Spare Parts Spare parts which are within 1 year from the date of purchase found upon inspection by an authorised Reece representative to be defective in construction, material or assembly, will be replaced free of charge. Warranty Conditions This warranty will apply only under all of the following conditions: The item has been installed by a licensed electrician The item has been installed for and subjected to domestic residential use only Failure is due to a fault in the manufacture of the product Proof of purchase (including the date of purchase) is provided The installation of the product is in accordance with the instructions provided This warranty does not include faults caused by: Unsuitable or improper use Incorrect installation or installation not in accordance with the instructions provided Installation or part installation by the purchaser or any person other than a LICENSED ELECTRICIAN Normal wear and tear Inadequate or complete lack of maintenance Chemical, electrochemical or electrical influences Harsh detergents or abrasive cleaners used on product finishes Powe surges Water penetration/damage EXCLUSIONS To the fullest extent permitted by law, Reece excludes all liability for damage or injury to any person, damage to any property, and any indirect consequential or other loss or damage. CLAIM PROCEDURE For all warranty queries customers are to contact the branch where the product was purchased. These details can be found on your purchase invoice. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. VAN.T1.7YR Don t risk it, use a licensed plumber.