Franke Specialist Range Pilatus Tap

Transcription

1 FR Pilatus Install 20/10/06 15:47 Page 3 Franke Specialist Range Pilatus Tap Installation Instructions For kitchens without compromise.

2 FR Pilatus Install 20/10/06 15:47 Page 4 Guarantee Your Franke mixer has been manufactured to the high standard you would expect of any Franke product but in the unlikely event that you should experience any defect in the materials or workmanship within one year of purchase, we will replace the faulty part free of charge. This is provided the mixer has only been used for normal domestic purposes in the UK and that the care, installation and maintenance instructions have been observed. This one year guarantee is extended to five years in the case of the valve mechanism. You should also retain your dated invoice as proof of purchase to validate any claims under our guarantee. Normal wear and tear is excluded from the guarantee. Decorative surface finishes are guaranteed for one year from the date of purchase provided our advice concerning care has been observed and no scouring agents have been used. Please read these instructions before you install and use the tap. All designs, descriptions and dimensions are subject to change without notice. Preparation First shut off your water heating system then, with your mains stop cock closed, open the lowest hot and cold taps in the house and allow to run until the cold storage tank and pipes are empty. (The hot water storage cylinder always remains full). Installation 1. Place the rubber washer in position at the base of the sink mixer (2). 2. Holding the sink mixer spout (3) (make sure that the hot marked red (4) the longer connection pipe) is on the left hand side when facing the sink mixer. 3. After the tap is placed in the sink, slide the triangular fixing plate (5) over the tails and secure hand tight using the rubber washer (6) steel washer (7) and fixing nut (8). Scuffs and scratches caused by improper installation or accidental damage are not covered by this guarantee. Neither are slight shade variations or any damage or defect caused by incorrect installation or abuse of the fitting. Design These mixers are available in Chrome or SilkSteel to complement all Franke sinks. 4. Screw flexi tail (9) marked red into connection pipe (4), (red, this is for the hot water supply) and tighten. 5. Screw flexi tail (10) (marked blue) into connection pipe (11), (this is for the cold water supply) and tighten. 6. Now finally fully tighten fixing nut (8) until the sink mixer is secure. Service In the event of parts or service being required, please contact: Central Services Telephone or South Services Telephone It is recommended that 15mm x 15mm compression fitting be used to connect mixer to supply pipes. Hot water should be connected to the left when viewed from the front.

3 FR Pilatus Install 20/10/06 15:47 Page 5 Attention Before installing the new tap it is essential that you thoroughly flush through the supply pipes in order to remove any remaining swarf, solder or other impurities. Ensure the tap is in the Off position (Refer to diagram operating sequence). How to care for your kitchen sink mixer. To maintain the appearance of this fitting, ensure it is cleaned only using a clean, soft damp cloth. A solution of warm water and mild liquid detergent may be used where necessary, and then the fitting rinsed thoroughly. Abrasive cleaners or acidic cleansers MUST NOT BE USED under any circumstances. Avoid contact with all solvents. Failure to carry out this simple procedure could cause problems or damage to the workings of the tap. Having first checked all new connections, turn on the mains stop cock, close all taps except the new one and as the system starts to refill check for leaks. Once you have satisfied yourself that there are no leaks, switch on the water heating. Technical data Operating pressure: Min 0.3 Max 6 Bars Recommended operating pressure: 0.5 Bars/5.5 Bars Hot water temperature: Max 70 C Recommended hot water temperature: 65 C Note: If these temperatures or water pressures are exceeded damage to the tap can result. Warning NB. Non return valves are built into both hot and cold flexi tails for security. A pressure reducing valve may be required to be fitted in high water pressure situations. It is also recommended to keep the spout in the opposite direction of the threaded hole for the threaded stud. While screwing the inlet flexi-tails to the body do not hold part (1) of the body in order to avoid unscrewing it. If found to be necessary then hold onto the spout bayonet holder of the mixer.

4 FR Pilatus Install 20/10/06 15:47 Page 6 Recommended Parts List No. Description Qty 1 Body 1 2 Rubber washer 1 3 Spout 1 4 Connector pipe 1 5 Triangular fixing plate 1 6 Rubber washer 1 7 Steel washer 1 8 Fixing nut 1 9 Flexi tails (red) 1 10 Flexi tails (blue) 1 11 Connector pipe Rubber washer (2) Rubber washer (6) 37mm Fixing nut (8) Sink top Triangular fixing plate (5) Steel washer (7) Connector pipe (11) Connector pipe (4) Cold Hot (10) (9) Flexi tails

5 FR Pilatus Install 20/10/06 15:47 Page Sink Top No. Description 1 Handle 2 Cartridge 3 Aerator 4 Gako O rings 5 Fixing set 6 Flexi tails Operating Sequence ON (Mixed) ON (Hot) ON (Cold) OFF

6 FR Pilatus Install 20/10/06 15:47 Page 2 Franke UK Limited West Park, MIOC Styal Road Manchester M22 5WB Service & Spares: Central Services mail@central-servicesuk.co.uk South Services sales@south-services.co.uk