FORMATIC Instruction Manual

Transcription

1 FORMATIC Instruction Manual Gibson Street, Leeds Road, Bradford West Yorkshire, England. BD3 9TR Telephone: +44 (0) Fax: +44 (0)

2 FORMATIC CONTENTS 1. Introduction 2. Technical Specification 3. Installation / Preparation for Production 4. Operating the Machine 5. Cleaning 6. Safety 7. Maintenance 8. Optional Extras; Hoppers Conveyors Auto Wire Clean Paper Attachment 10. Recommended Spares List 11. Wiring Diagrams

3 (1) INTRODUCTION The Formatic range by Deighton Manufacturing (UK) Ltd guarantees accurate forming and portioning of a wide variety of food mixtures and products. Encompassing Retail, Commercial and Industrial sized models, the range has been designed to accommodate the needs of both high and low volume producers. Simplicity is the strength of the Formatic system. Suited to a variety of mixtures of numerous textures and consistencies, the formatic uses synchronised paddles to gently press mixture into the required form shape. Assisted by the wire drum scraper, the formed product is then smoothly ejected onto the conveyor, presenting it for packaging or further processing.

4 (2) TECHNICAL SPECIFICATION Formatic UL approved Formatics Only Power requirements - On UL approved machines use a 20 amp Class B GFCI (receptacle).

5 Retail Machine R1200 R2200 R3000 Size: Length (A) Width (B) Height (C) Weight:- 75 Kg 75 Kg 75 Kg Product Output:- 1200/hr 2200/hr 3000/hr Hopper Capacity:- 18 litres 18 litres 18 litres Product Size (max):- 140mm x 120mm x 24mm thick (34mm deep drop) Electrical Supply:- 220/240V 50 Hz AC Power:- 550 Watt 550 Watt 750 Watt It should be noted that on certain products it is possible to increase the product out put by specifying a 180 degree machine. This enables a form to be place on each side of the drum and effectively doubling product output.

6 Commercial Machine C2000 C4000 Size: Length (A) Width (B) Height (C) Weight:- 90 Kg 90 Kg Product Output:- 2000/hr 4000/hr Hopper Capacity:- 20 Kg 20 Kg Product Size (max):- 135mm x 135mm x 24mm thick (34mm deep drop) Electrical Supply:- 220/240V 50 Hz AC Power:- 550 Watt 550 Watt It should be noted that on certain products it is possible to increase the product out put by specifying a 180 degree machine. This enables a form to be place on each side of the drum and effectively doubling product output.

7 Industrial Machine I4000 IR4000 I4000/50 Size: Length (A) Width (B) Height (C) Weight:- 100 Kg 90 Kg 150 Kg Product Output:- 4000/hr 4000/hr 4000/hr Hopper Capacity:- 30 Kg 15 Kg 30 Kg Product Size (max):- 150 x 150 x x 118 x x 150 x 50 Electrical Supply:- 220/240V 50 Hz AC Power: Watt 1500 Watt 1500 Watt It should be noted that on certain products it is possible to increase the product out put by specifying a 180 degree machine. This enables a form to be place on each side of the drum and effectively doubling product output.

8 (3) INSTALLATION PROCEDURE 3.1 Check the Formatic for transport damage and report any immediately to Deighton Manufacturing Ltd. 3.2 Before Operating the machine:- Remove any packaging material Position the Formatic relative to any other equipment it is to connect with. Connect the machine to the correct supply. 3.3 Step 1; Locate the selected drum onto the drive shaft ensuring that the keyways are aligned and push the drum completely home (if the form is not at the top you may need to lift the ejector set over the cam). Fit the paper cam/guard over the drum on the end of the shaft and secure with locking knob, cam cannot be removed without rotating the hopper due to the safety pin located on each hopper (left hand thread).

9 Step 2; Locate the conveyor platform onto the pivot shaft positioned to the bottom left of the drum. Slip the conveyor belt onto the nylon drive roller and around the platform nose roller, with the platform rotated to the 10 o clock position. Set the platform down so that it rest on the round conveyor stop and lock in place using the hand knob provided. Fit the scraper wire assembly into the support brackets on the nose of the conveyor and adjust the tension. Step 3; Ensure the hopper sealing ring is pressed firmly into its retaining slot in the machine top. Slacken the four hopper securing knobs on the top of the machine. Place the hopper into the top machined recess on the hopper seal and rotate such that the hopper securing lugs engage with the hand knob studs. Secure the hopper in place by tightening the hand knobs. Note: the hopper will only locate in one position with the hopper bars towards the front right of the machine. Always ensure the hopper is loaded correctly onto the seal in the hopper top. Check the hopper bar is secure in the hopper. If it has been removed for any reason when it is replaced use locktight to lock in position. Step 4; Position the chosen paddles onto the paddle shaft at the top of the machine, ensuring the keyways are aligned, and secure in place with paddle knob. Step 5; The scraper shaft assembly (not shown) locates into the housing on the left hand side of the drum. Before assembling the scraper shaft, ensure that the shaft locking screw is clear of the housing bore. Push home the assembly so that the wire support bar nearest the front of the machine engages in the housing slot. To ensure alignment in the housing slot it will be necessary to rotate the housing clockwise with the aid of the locking screw. When in position secure with locking screw. The working position of the scraper, although factory set, can be adjusted with a grub screw. This is located under a bung on the left hand side of the machine. The tension of the scraper wire can be adjusted by rotating the front scraper bar hand knob.

10 (4) OPERATING THE MACHINE Connect up to the supply and press the green start button. The form drum conveyor and hopper paddles should rotate smoothly and quietly (if a foot switch is fitted this will need depressing to operate). If any safety interlock is not in place the machine will not operate. Relocate the interlock and press the green start button to operate. To stop the machine press the red stop button (or release foot switch if fitted). If the machine will not operate check the following; 1. The machine power is switched on 2. The hopper guard micro switch is in place 3. There is nothing preventing the free rotation of paddles or drum 4. The stop button is not depressed If, after carrying out these simple checks, you still do not get any rotation when the start button is depressed, please contact your machine supplier or the manufacturer for further assistance. Always clean the machine thoroughly prior to production (see cleaning). When using an auto wire cleaning system always lubricate the metal shaft the scraper moves along with the food lubrication spray provided prior to using the machine. Initially practice starting and stopping the machine until you are able to stop the forming drum with the mould at 90 degrees to the hopper, being positioned on the left hand side of the forming drum when viewed from the front. This is the correct rest position and allows for simple removal and replacement of the forming drum and also makes it easy to vary the depth of the form to set the finished products weight. Always make sure that there are no large pieces of bone or other hard items in the mix as they can damage your machine.

11 To adjust the thickness and weight of the finished product (the variation available being between 6mm and 34mm, approximately 3 8 oz) use the following routine. Approximately half fill the hopper with the mix to be used, checking it s suitability Start the machine until two full forms are obtained Weigh the fully formed product and either increase or decrease the thickness until the correct weight is achieved. This is done by removing the paper attachment cam/guard, releasing the lock nut (item 1) and turning the spiral cam (item 2) the required amount. Re-tighten the lock nut and replace the paper attachment guard/cam and repeat procedure until correct setting is achieved. The machine is now ready to run. Note; The scraper wire should be kept as clean as possible to aid the release of the product from the drum. The manual scraping of the wire should be carried out in the part of the cycle when the wire is away from the drum.

12 Generally the size of the paddles should balance with the size of the product being formed i.e., small paddle combination for a small product. Deighton Manufacturing will supply the machine with a series of paddles suitable for the mix being used and the form sizes being created however you can obtain various sizes and combinations if problems occur with those supplied With each mix you use for the first time start it with the smallest bottom paddle available with no top paddle (In this case a top paddle spacer will have been supplied if deemed appropriate). If the form will not fill, fit the smallest top paddle and if problems still occur continue to fit a larger bottom then top paddle until the form is filled.

13 If a mix is sticking to the hopper a causing a tunnelling effect a knockdown paddle can be supplied to release the product from the hopper and push it into the path of the pressure paddles. If, in the unlikely event, problems still occur in filling and forming it may be necessary to modify the mix slightly to achieve the desired results.

14 (5) DISMANTLING AND CLEANING Please ensure the machine is disconnected from the mains supply before proceeding to clean. Dismantle the machine in the reverse order to assembly. Wash all parts with hot water (at a temperature no greater than 60 c) before the product has a chance to dry. Do not use strong alkaline/acid based cleaners. Parts should not be scraped with metal objects, a plastic scraper is an ideal cleaning aid.

15 (6) SAFETY 1. Always disconnect mains supply before servicing, cleaning or changing the drum 2. Disconnect mains supply when removing drum and guard 3. The machine should not be run when the drum guard is removed 4. During operation the hopper guard can be opened to refill. This will automatically stop the machine 5. When replacing the scraper wire remove the assembly from the machine. The machine must be disconnected from the mains supply before removing assembly. 6. No attempt should be made to override the safety switches or run the machine without the guards in place 7. Use a 13 amp fuse in the plug Ensure all operatives read these instructions and are fully conversant with the machines operations and safety procedures These machines are to be operated by one person, in the case where an open hopper is used the machine is to be isolated before any attempt is made to put hands in the hopper. The machine is not to be operated when anyone is reaching into the hopper whether for cleaning, blockages or any other reasons.

16 (7) MAINTENANCE The only maintenance that is required is a light oiling (food lube) of the form drum mechanism and scraper shaft after cleaning. The most beneficial thing to extend the life of the machine is; Keep it clean and dry when not in use Ensure there are no large, hard objects within the mix Ensure lubricated air is used to supply cylinder (if fitted) Ensure how the operator knows how the machine works GUARANTEE The machine is guaranteed for twelve months against breakdown. The items not covered under the guarantee are those which wear through normal operation. Replacements are readily available from the manufacturer.

17 (8) OPTIONAL EXTRAS Hoppers As well as the standard hopper supplied with the machine several other hopper options are available for all the range of Formatics. Low Level Hopper Generally used for delicate mixes where the product quality can deteriorate when over mixed by the paddles. Requires more regular filling. Extended Hopper Used in situations where a large batch of products is being produced to reduce the frequency of filling.

18 75 Litre Hopper Used in large batch production to reduce the frequency of refilling 200 Litre Hopper Again used in very large production to reduce frequency of refilling. Can be filled using a 200kg bin lift.

19 We can also supply a gooseneck or funnel feeder for the standard, low level and extended hoppers. These enable the machine to be continually filled whilst in operation. Conveyors The Formatic machines come supplied with a standard length conveyor (length varies depending on model). Also available are extended and jointed conveyors. Retail Formatic; Commercial Formatic; Industrial Formatic; Extended conveyors of 750mm and 1200mm long and a jointed conveyor of 750mm long are available. Extended conveyors of 1000mm and 1500mm are available and a jointed conveyor of 1000mm. Extended conveyors of 1000mm and 1500mm are available and a jointed conveyor of 1000mm.

20 Auto Wire Clean On the standard machine the scraper wire is cleaned manually at regular intervals to improve the release of the formed product. On a lot of meat products it is essential to clean the wire after every form. This can be done automatically with the use of the Auto Wire Clean system. The system uses a pneumatic cylinder and therefore requires a compressed air supply to the machine. A small silent run compressor can also be supplied if required. Maximum air pressure 145PSI (10Bar) (1MPa). Minimum air pressure 101.5PSI (7Bar) (0.7MPa). Food lubrication spray. Paper Attachment Mainly used in the meat industry when there is a requirement to put paper interleaves between formed products. The papers (which can also be supplied by Deighton Manufacturing) are loaded onto a cartridge and then released onto the base of the formed product before been ejected onto the conveyor. Position of the paper relative to the form can be adjusted simply by rotating the paper attachment cam.

21 RECOMMENDED SPARES LIST Description Scraper Wire Conveyor Scraper Holder Scraper Wire Adjustment Screw Scraper Tensioning Stud Hopper Seal Scraper Wire Bush Assembly Hopper Knob Drum Knob Paddle Knob Conveyor Pivot Knob Start Button Boot Relay Relay Base Elobau Conveyor Scraper Assem Drive Chain Split Link Part Number F145 F452 F805W FM4150 F117A (Retail Machine) F117C (Commercial Machine) F135 (Industrial Machine) F4323 F124 F129A F130 F127 F1004A F1039 F1040 F1015A F496BK (Retail/Commercial) F496 (Industrial) F124BK F115

22 Paddle Shaft Seal Drum Shaft Seal F1141 F1100 Scraper Arm (Metal) F522-1 Scraper Arm (Plastic) F5221

23

24

25

26

27

28 WIRING DIAGRAMS

29

30

31

32

33 Gibson Street, Leeds Road, Bradford, West Yorkshire, BD3 9TR. England. EC DECLARATION OF CONFORMITY Declaration We hereby declare that the following machinery complies with the essential Health and Safety requirements of the Machinery Directives 2006/42/EC, EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and regulation EC 1935/2004 on materials and articles in contact with food. Harmonised Standards and Applicable Amendments EN Electromagnetic compatibility (EMC) - Generic standards - Immunity standard for industrial environments. EN Electromagnetic compatibility (EMC) - Generic standards - Emission standard for industrial environments. EN : A Safety of Machinery - Electrical equipment of machines - Specification for general requirements. EN ISO : 2015 Safety of Machinery - Safety related parts of control systems - Part1: General principles for design (ISO : 2006). EN ISO 13857: 2008 Safety of machinery - Safety distances to prevent danger zones being reached by the upper and lower limbs. Machine Description: Serial Number: Manufactured By: Deighton Manufacturing UK Ltd, Gibson Street, Leeds Road, Bradford, BD3 9TR. ENGLAND. Person Authorised to draw up declaration of conformity. Position: Managing Director Name: A Hamilton Signed: Date: Person Authorised to Compile Technical File- J.Wade Deighton Manufacturing UK Ltd, Gibson Street, Leeds Road, Bradford, BD3 9TR, England.