ADA Compliant Wall-Mount Fountain and Bottle Filler

Transcription

1 model with1920 ADA Compliant Wall-Mount Fountain and Bottle Filler FEATURES & BENEFITS CONSTRUCTION Barrier-free design with an 18-gauge Type 304 satin fi nished stainless steel swirl bowl assembly mounted on a 14-gauge Type 304 stainless steel wall bracket. Unit includes an in-wall mounting frame, and front panel access for P-trap and stop. BOTTLE FILLER Vandal-resistant, 14-gauge Type 304 stainless steel bottle fi ller housing with push button operation using the same all stainless steel valve with front access serviceability used in Haws drinking fountains. PUSH BUTTON VALVE The push-button activated valve assembly allows for front access stream adjustment as well as cartridge and strainer access. The valve works at an operating pressure range of 30 to 90 psi (2.1 to 6.2 bar). BUBBLER HEAD Polished chrome-plated brass bubbler head with integral laminar fl ow prevents splashing while providing water at.45 gpm. The integral basin shank and inserted roll pin add vandal resistance strength. MOUNTING Galvanized frame and 10-gauge surface plate provide the maximum mounting strength for the single bubbler drinking fountains. QUALITY CONTROL Pre-built fountain and bottle fi lter are pressure tested to ensure no leaks and proper functionality. OPTIONS Mounting Plate: Model 6700R, on-wall mounting plate for 1920 series bottle fi llers, single or dual fountain retrofi t installations. Water Filter: Model 6425, 6 x 2 (15.2 x 5.1 cm) activated carbon fi lter removes chlorine taste and odor, and water borne sediment. Water Filter: Model 6426, 10 x 2 (25.4 x 5.1 cm), in-line lead removal element that reduces lead from incoming water supply. Remote Drinking Fountain Water Chiller: Model HCR8, 8 gph (30.3 L) remote water chiller provides instantaneous cooling to meet a continuous demand for chilled water. Custom Logo Panel: Standard Model 6475 comes with Hydration By Haws logo. Customize the panel with your choice of logo, slogan, or graphic. For customization, call MODEL CHOICE / BP15 / 1920 / MTGFR.DF1 Model fountain with stainless steel back panel, stainless steel bottle fi ller, and galvanized steel in-wall mounting frame. 1001HPSMS / BP15HPS / 1920HPS / MTGFR.DF1 Model 1001HPSMS fountain with high-polished stainless steel back panel, high-polished stainless steel bottle fi ller, and galvanized steel in-wall mounting frame. SPECIFICATIONS Model with 1920 bottle fi ller: ADA compliant wall- mounted drinking fountain and bottle fi ller with push button operation. Fountain shall include an 18-gauge Type 304 stainless steel satin fi nish basin with integral swirl design, stainless steel satin-fi nish back and access panel allowing for front access of P-trap and stop, in-wall mounting frame, polished chrome-plated brass vandalresistant bubbler head with integral laminar anti-squirt fl ow, chrome-plated brass vandal-resistant waste strainer, and 1-1/4 O.D. (3.2 cm) waste pipe. Fountain and bottle fi ller use 14-gauge Type 304 stainless steel wall brackets, push-button operated stainless steel valves with frontaccessible cartridge and fl ow adjustment, 100% leadfree waterways, and vandal-resistant bottom plate. CSA certifi ed and ADA accessible, NSF/ANSI Standard 61, Section 9, lead free Kleppe Lane :: Sparks, NV :: p :: f :: e. info@hawsco.com ::

2 NOTES: 1. HOLD DIMENSIONS ± 1/8" (3.2mm). 2. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD BE ADHERED TO FOR INSTALLATION DIMENSIONS (LOCATIONS), WASTE AND SUPPLY REQUIREMENTS OTHER THAN SHOWN. 3. ** INSTALLER MUST PROVIDE TRAP FOR PROPER INSTALLATION. 4 REFER TO 5874SS OPERATION AND MAINTENANCE MANUAL FOR PUSH BUTTON AND VALVE INSTALLATION/MAINTENANCE INSTRUCTIONS. BACK 15" 381mm 14-1/8" 359mm 1-3/4" 44mm REMOVE VALVE FROM PUSH BUTTON TO INSTALL WASTE ELBOW ONTO BOWL. AFTER WASTE ELBOW IS INSTALLED, REINSTALL VALVE & ADJUST FLOW 3" 76mm /8" 359mm 18-5/8" 473mm FRAME FLANGE BACK WALL FACE Ø 3/8" SUPPLY TUBING & SCREWDRIVER STOP IMPORTANT: MOUNTING FRAME MUST BE INSTALLED SO THAT FRAME FLANGE BUTTS AGAINST FINISHED WALL FACE. 15-5/8" 397mm 18" 457mm 34" 864mm 1-1/4" O.D. WASTE BEND WASTE BEND * * 1-1/4" IPS TRAP 28-11/16" 729mm FOUNTAIN SUPPLY 18-1/8" 460mm ACCESS 16-5/8" 422mm 27" 686mm FLOOR LINE MTGFR.DF1 MOUNTING FRAME WALL FACE 27-7/8" 708mm FOUNTAIN WASTE 2013 (775) FAX (755) ECN: 4828 HM D DRAWN: DATE: CHK'D.: /1001HPSMS DRAWING NO. PM 08/02/99 REV DRINKING FOUNTAIN 14221A00 8 SCALE: 1:14 DRAWING TYPE: INSTALLATION SIZE: A SHEET 1 OF 1 C R Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.

3 MOUNTING PLATE (BEHIND FINISH WALL) - OR R RETROFIT PLATE (ON TOP OF FINISH WALL) 1920/1920HPS BP15/BP15HPS INSTALLATION ABOVE HAWS AND 1001HPSMS * IF YOUR FOUNTAIN IS THIS STYLE USE THESE DIMENSIONS 3/8" PUSH IN TEE (CONNECT TO FOUNTAIN SUPPLY) 1. SEE SEPARATE INSTALLATION DRAWINGS FOR MOUNTING PLATES AND BACKS 2. WHEN INSTALLING THIS UNIT, LOCAL, STATE OR FEDERAL CODES SHOULD BE ADHERED TO FOR INSTALLATION LOCATIONS, WASTE & SUPPLY REQUIREMENTS OTHER THAN SHOWN. C (775) FAX (775) ECN: GC -20 DRAWN: DATE: CHK'D.: MODEL AND 1001HPSMS REVISION GC 07/13/17 WITH MODEL 1920 BOTTLE FILLER 0A.1 SCALE: N/A DRAWING TYPE: INSTALLATION SIZE: A SHEET 1 OF 2 R 2017 Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 1 of 2

4 1920 MOUNTING HOLE LOCATIONS NOTES: 1. C SEE SEPERATE INSTALLATION DRAWINGS FOR MOUNTING PLATES AND BACKS 2. WHEN INSTALLING THIS UNIT, LOCAL, STATE OR FEDERAL CODES SHOULD BE ADHERED TO FOR INSTALLATION LOCATIONS, WASTE & SUPPLY REQUIREMENTS OTHER THAN SHOWN. (775) FAX (775) ECN: 5172 MJ DRAWN: DATE: CHK'D.: MODEL 1920/1920HPS/1920W REVISION DS 05/25/16 FV 2 FV 02/27/17 SCALE: N/A DRAWING TYPE: INSTALLATION SIZE: A SHEET 1 OF 5 R 2017 Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation D

5