United Kingdom. Smart Thermostat Low Voltage Digital Installations. Guide for Professional Installers

Transcription

1 United Kingdom Part 2 of 2 Smart Thermostat Low Voltage Digital Installations Guide for Professional Installers If you are not a professional installer and want to install tado yourself, get step-by-step instructions at tado.com/start

2 POLARITY-PROTECTED WIRING For all two-wire digital installations the wires connected to + and - on tado can be interchanged CAUTION Make sure to turn the power off before you start 10/2018

3 Optional Accessory Use the tado Trim Plate behind the Smart Thermostat or Extension Kit if needed. This can be obtained separately at tado.com/trim-plate

4 OpenTherm 1. Wiring: OpenTherm Wired Setup: Smart Thermostat is wired directly to the boiler Smart Thermostat Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit 4

5 OT OpenTherm Boiler Smart Thermostat MAX 36 V DC OT Boiler Extension Kit The Extension Kit requires a separate 230 V power supply at N and L for OpenTherm installations 5

6 OpenTherm 2. Connect Internet Bridge to Router If no free USB jack available - plug to power socket 6 Connect Internet Bridge to router Press pairing button until the LED blinks to activate pairing mode Pairing allows other devices to connect to the Internet Bridge

7 3. Pair Extension Kit with Internet Bridge Wireless Setup: Smart Thermostat installed wirelessly with receiver OpenTherm Smart Thermostat & Extension Kit 3 SEC 2 MIN Blinking 4x short - pause -... Fast Blinking Press button for 3 sec until LED starts blinking fast Paired Blinking 2x short - pause -... If failed: Restart pairing and make sure that the distance between the devices is at least 3 m while pairing 7

8 OpenTherm 4. Pair Smart Thermostat with Internet Bridge 2 MIN 3 SEC Remove battery strip and press button Press button for 3 sec - release Pairing Paired If failed: Press the button to clear the error Restart pairing and make sure that the distance between the devices is at least 3 m while pairing 8

9 Open Installer Menu OpenTherm 2 MIN 3 SEC 3 SEC Press button for 3 sec - release Press button for 3 sec - release Installer Menu is loading Ready for configuration If failed: Repeat the process to open Installer Menu Make sure that the distance between the devices is at least 3 m while loading the menu 9

10 OpenTherm 5. Configuration: OpenTherm Wired Setup: Smart Thermostat is wired directly to the boiler Smart Thermostat Select OpenTherm D01 Select Heating Circuit HC01 Activate Hot Water Control Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit Select Temperature Sensor TS Select Heating Circuit HC01 Activate Hot Water Control 10

11 OpenTherm 2 MIN No Extension Kit OpenTherm installation complete 1. Test the system 2. Hand over the registration card to the customer 2 MIN Extension Kit Present Select OpenTherm D01 Configuration download active after saving Installer Menu (up to 2 min) 11

12 1. Wiring: Vaillant ebus Wired Setup: Smart Thermostat is wired directly to the boiler Vaillant ebus Smart Thermostat Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit 12

13 ebus Vaillant ebus Boiler Smart Thermostat MAX 36 V DC ebus Boiler Extension Kit 13

14 2. Connect Internet Bridge to Router Vaillant ebus If no free USB jack available - plug to power socket 14 Connect Internet Bridge to router Press pairing button until the LED blinks to activate pairing mode Pairing allows other devices to connect to the Internet Bridge

15 3. Pair Extension Kit with Internet Bridge Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit 3 SEC 2 MIN Blinking 4x short - pause -... Vaillant ebus Fast Blinking Press button for 3 sec until LED starts blinking fast Paired Blinking 2x short - pause -... If failed: Restart pairing and make sure that the distance between the devices is at least 3 m while pairing 15

16 4. Pair Smart Thermostat with Internet Bridge Vaillant ebus 2 MIN 3 SEC Remove battery strip and press button Press button for 3 sec - release Pairing Paired If failed: Press the button to clear the error Restart pairing and make sure that the distance between the devices is at least 3 m while pairing 16

17 Open Installer Menu Vaillant ebus 2 MIN 3 SEC 3 SEC Press button for 3 sec - release Press button for 3 sec - release Installer Menu is loading Ready for configuration If failed: Repeat the process to open Installer Menu Make sure that the distance between the devices is at least 3 m while loading the menu 17

18 5. Configuration: Vaillant ebus Wired Setup: Smart Thermostat is wired directly to the boiler Vaillant ebus Smart Thermostat Select ebus D05 or D07 D05 for systems with a calormatic VRC430/470 (VR81) D07 Standard Vaillant ebus Select Heating Circuit HC01 or HC02 Activate Hot Water Control (only for D07) Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit Select Temperature Sensor TS Select Heating Circuit HC01 or HC02 Activate Hot Water Control (only for D07) 18

19 2 MIN No Extension Kit Vaillant ebus installation complete 1. Test the system 2. Hand over the registration card to the customer Vaillant ebus 2 MIN Extension Kit Present Select ebus D05 or D07 Configuration download active after saving Installer Menu (up to 2 min) 19

20 1. Wiring: Viessmann KM-Bus Wired Setup: Smart Thermostat is wired directly to the boiler Smart Thermostat Viessmann KM-Bus Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit 20

21 KM-Bus 1 2 Boiler Smart Thermostat MAX 36 V DC KM-Bus 1 2 Viessmann KM-Bus Boiler Extension Kit 21

22 2. Connect Internet Bridge to Router If no free USB jack available - plug to power socket Viessmann KM-Bus 22 Connect Internet Bridge to router Press pairing button until the LED blinks to activate pairing mode Pairing allows other devices to connect to the Internet Bridge

23 3. Pair Extension Kit with Internet Bridge Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit 3 SEC 2 MIN Blinking 4x short - pause -... Fast Blinking Press button for 3 sec until LED starts blinking fast Paired Viessmann KM-Bus Blinking 2x short - pause -... If failed: Restart pairing and make sure that the distance between the devices is at least 3 m while pairing 23

24 4. Pair Smart Thermostat with Internet Bridge 2 MIN 3 SEC Viessmann KM-Bus Remove battery strip and press button Press button for 3 sec - release Pairing Paired If failed: Press the button to clear the error Restart pairing and make sure that the distance between the devices is at least 3 m while pairing 24

25 Open Installer Menu 2 MIN 3 SEC 3 SEC Press button for 3 sec - release Press button for 3 sec - release Installer Menu is loading Ready for configuration Viessmann KM-Bus If failed: Repeat the process to open Installer Menu Make sure that the distance between the devices is at least 3 m while loading the menu 25

26 5.Configuration: Viessmann KM-Bus Wired Setup: Smart Thermostat is wired directly to the boiler Smart Thermostat Select KM-Bus D37 Select Heating Circuit HC01 or HC02 No Hot Water Control Viessmann KM-Bus Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit Select Temperature Sensor TS Select Heating Circuit HC01 or HC02 No Hot Water Control 26

27 2 min No Extension Kit 2 MIN Viessmann KM-Bus Extension Kit Present Select KM-Bus D37 Configuration download active after saving Installer Menu (up to 2 min) 27

28 Viessmann KM-Bus 28

29 6. Heating System Settings For the heating circuit controlled by tado, set the same settings as for a Viessmann Vitotrol 200 remote control. Controller Heating System Settings 90: Time constant for calculating the adjusted outside temperature 12 Vitotronic 200 GW.. Vitotronic 300 GW.. Vitotronic 200 HO.. Vitotronic 200 KW.. Vitotronic 300 KW.. Vitotronic 200 KO.. A0: Remote Control b0: Room Temperature Hook-up b2: Room Influence Factor b5: Heating Circuit Pump Logic FA: Increase of the set flow temperature 0 1 (If 1 can not be selected, use 2) 3 64 (If 64 can not be selected, use 31) 5 (If 5 can not be selected, use 1) Viessmann KM-Bus Viessmann KM-Bus installation complete 1. Test the system 2. Hand over the registration card to the customer 29

30 1. Wiring: Worcester HT-Bus Wired Setup: Smart Thermostat is wired directly to the boiler Smart Thermostat Wireless Setup: Smart Thermostat installed wirelessly with receiver Worcester HT-Bus Smart Thermostat & Extension Kit 30

31 B B Boiler Smart Thermostat MAX 36 V DC B B Boiler Extension Kit Worcester HT-Bus 31

32 2. Connect Internet Bridge to Router If no free USB jack available - plug to power socket Worcester HT-Bus 32 Connect Internet Bridge to router Press pairing button until the LED blinks to activate pairing mode Pairing allows other devices to connect to the Internet Bridge

33 3. Pair Extension Kit with Internet Bridge Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit 3 SEC 2 MIN Blinking 4x short - pause -... Fast Blinking Press button for 3 sec until LED starts blinking fast Paired Blinking 2x short - pause -... If failed: Restart pairing and make sure that the distance between the devices is at least 3 m while pairing Worcester HT-Bus 33

34 4. Pair Smart Thermostat with Internet Bridge 2 MIN 3 SEC Remove battery strip and press button Press button for 3 sec - release Pairing Paired Worcester HT-Bus If failed: Press the button to clear the error Restart pairing and make sure that the distance between the devices is at least 3 m while pairing 34

35 Open Installer Menu 2 MIN 3 SEC 3 SEC Press button for 3 sec - release Press button for 3 sec - release Installer Menu is loading Ready for configuration If failed: Repeat the process to open Installer Menu Make sure that the distance between the devices is at least 3 m while loading the menu Worcester HT-Bus 35

36 5. Wiring: Worcester HT-Bus Wired Setup: Smart Thermostat is wired directly to the boiler Smart Thermostat D17 for systems without an FW controller Select HT-Bus D17 or D18 D18 for systems with an FW controller (e.g. FW120) Select Heating Circuit HC01 or HC02 Activate Hot Water Control (only for D17) Wireless Setup: Smart Thermostat installed wirelessly with receiver Worcester HT-Bus Smart Thermostat & Extension Kit Select Temperature Sensor TS Select Heating Circuit HC01 or HC02 Activate Hot Water Control (only for D17) 36

37 2 MIN No Extension Kit 2 MIN Extension Kit Present Select HT-Bus D17 or D18 Configuration download active after saving Installer Menu (up to 2 min) Worcester HT-Bus 37

38 Worcester HT-Bus 38

39 6. Heating System Settings For the heating circuit controlled by tado, set the same settings as for a Worcester remote control. Controllers Heating System Settings Remote Control (heating circuit ) FB10 Room influence 50% FW 100 FW 120 FW 200 FW 500 Room influence enabled for levels Sensor used for room influence Mode selector (switch below the display) Comfort-Eco-Frost Sensor on FB10 (only when the FW controller is installed externally) Auto (FW100: clock symbol) Worcester HT-Bus installation complete 1. Test the system 2. Hand over the registration card to the customer Worcester HT-Bus 39

40 Get expert advice on the tado installer hotline: or at tado.com/installers _F