INT853A. Pre-Heating Station INSTRUCTION MANUAL
|
|
- Gyles Woods
- 5 years ago
- Views:
Transcription
1 INT853A Pre-Heating Station INSTRUCTION MANUAL Thank you for purchasing Aoyue Int853A Pre Heating Station. It is important to read the manual before using the equipment. Please keep manual in accessible place for future reference. Manufacturer: AOYUE TONGYI ELECTRONIC EQUIPMENT FACTORY Jishui Industrial Zone, Nantou, Zhongshan City, Guangdong Province, P.R.China 10
2 BASIC TROUBLESHOOTING GUIDE This manual is designed to familiarize and instruct the technician with the proper operation and maintenance of the equipment. The Care and Safety Precautions section explains the hazards of using any type of soldering or reworking device. Please read carefully and observe the guidelines in order to maximize usage and minimize the risk of injury or accidents. PROBLEM 1: THE UNIT HAS NO POWER 1. Check if the unit is switched ON. 2. Check the fuse. Replace with the same type if fuse is blown. 3. Check the power cord and make sure there are no disconnections. 4. Verify that the unit is properly connected to the power source. PROBLEM 2: TEMPERATURE IS NOT INCREASING Description: Actual temperature reading is not increasing or decreasing based on desired level. A constant display of relatively low temperature reading on the display panel. Cause & Solution: The thermal sensor may be shorted or Heating element is damaged, if unit has been recently opened for heating element replacement double check the wires for loose connection or short. The heating element may be broken and needs to be replaced. PROBLEM 3: THE TEMPERATURE ADJUSTMENT KNOB IS NOT WORKING Description: Turning the temperature setting knob does not alter the display or show the set temperature level nor does the set temperature level changes with the turn of the knob. Cause & Solution: The temperature knob may be damaged and needs to be replaced. Have the unit serviced by a certified technician. PROBLEM 4: UNIT DISPLAYS UNKNOWN CHARACTERS SOLUTION: Turn OFF the main power switch and ON again, if the problem persists have the unit serviced by a qualified technician. 2 PROBLEM 5: OTHER PROBLEMS NOT MENTIONED RECOMMENDATION: Contact your vendor. 9
3 OPERATING SPECIFICATION Aoyue 936A GUIDELINES 规格 NOTE: Please refer to the CONTROL PANEL GUIDE page for buttons and display panel directory. I. INITIAL PROCEDURES 1. Plug the device to the main power source using the power cord provided in the package. 2. Place the PCB on top of the circuit board holder. 3. Adjust the beams such that the component to be heated is placed somewhere at the center of the preheating surface and the whole PCB locked on the beams to prevent unnecessary movement. 4. Turn ON the main power switch. 5. Adjust the temperature according to component size and circuit board thickness (if possible). 6. Allow the PCB/component to be heated until it is ready for rework. TABLE OF CONTENTS Product Description 4 Package Inclusion 4 Specifications 5 Functions and Features 5 Safety Precautions 6 Control Panel Guide 7 Operating Guidelines Basic Troubleshooting Guide 9 II. REMOVING THE COMPONENT 1. Follow INITIAL PROCEDURES above. 2. Heat the component until the solder starts to shimmer. 3. Use an IC popper or extractor to remove the component when the solder is completely molten. NOTE: Do not move the PCB immediately after removing the component. Adjacent components may be affected and may cause to move because of heat retention on the PCB. 4. Turn OFF the main power switch when work is finished. 5. Unplug the unit from the main power source. 6. Wait for the PCB to cool down before removing from the support beams. IMPORTANT: Pre heat temperature should be carefully set. Improper calibration may deform the PCB and/or burn the components if the temperature is too high or the component 8 concerned will not be detached if the temperature is too low. 3
4 PRODUCT DESCRIPTION CONTROL 焊铁头的维护和使用 Aoyue PANEL 936 规格 GUIDE The Aoyue Int853A Pre Heating Station is an electrostatic discharge (ESD) safe equipment used for repairing electronic PCBs and communication equipments that require pre heating. SP2000 PACKAGE INCLUSION Int853A Main Station w/ Mechanical Bar Supports for PCB 1 2 LEGEND: Main Power Switch 2 Temperature Adjustment Knob 3 Digital Temperature Display 4 Real (or Actual) Temperature / Set Temperature Display Activation Switch Power Cord IMPORTANT REMINDERS: 1.Make sure the equipment is placed on a flat, stable, heatresistant surface. 2.Ensure all function switches are OFF prior to plugging in. 3.Ensure all terminal connections are properly secured. 4 7
5 SAFETY PRECAUTIONS CAUTION: Improper usage can cause serious injury to personnel and/or damage to equipment and work area. For your own safety, please observe the following precautions. Check each component after opening the package to make sure everything is in good condition. If there are any suspected damage, do not use the item and report the issue to your vendor. Turn OFF the power switch and unplug the device from the power source when moving the device from one place to another. Do not strike or subject the main unit (and all its components) to physical shock. Handle with care. Never drop or sharply jolt the unit. Contains delicate parts that may break if the unit is dropped. Make sure the equipment is always grounded. Always connect power to a grounded receptacle. Temperature may reach as high as 380 C when switched ON. Do not use the device near flammable gases, paper and other flammable materials. Do not touch heated parts, which can cause severe burns. Do not touch metallic parts near the tip. Disconnect the plug from the power source if the unit will not be used for a long period. Turn off power during breaks, if possible. Use only genuine replacement parts. Turn off and let the unit cool down before replacing any part. Soldering process produces smoke, use on well ventilated places. Do not alter the unit in any manner. Use proper safety procedures when handling equipments of extremely hot temperatures. Power Input: Operating Frequency: Station Dimensions: Weight: Power Consumption: Current Rating: SPECIFICATIONS MAIN STATION available in 110V / 220V 220 (w) x 73 (h) x 247 (d) mm 3.2 Kg 600W Temperature Range: 98 C 380 C Heating Element Type: Maximum Allowable PCB Size: Maximum Pre Heating Area: 50 Hz / 60 Hz 3A Quartz Infrared 187 (w) x 156 (h) mm 130 (w) x 130 (w) mm FUNCTIONS Aoyue and 936 规格 FEATURES Electrostatic discharge (ESD) safe equipment. Digital display of user configured and actual temperatures for precise temperature measurement and monitoring. Knob type regulator for temperature adjustment. Configurable temperature between 98 C and 380 C. Integrated beam supports to prevent PCB movement. Utilizes large quartz infrared for safe heating of surface. Suitable for pre heating electronic PCBs of various sizes. 6 5
SP2000. Solder Pot. Environment Friendly. Instruction Manual
SP2000 Environment Friendly Solder Pot Instruction Manual Thank you for purchasing the Aoyue SP2000 Solder Pot. Please read the manual before using the unit. Keep manual in accessible place for future
More informationSP2000. Solder Pot Instruction Manual. Environment Friendly
SP2000 Environment Friendly Solder Pot Instruction Manual Thank you for purchasing the Aoyue SP2000 Solder Pot. Please read the manual before using the unit. Keep manual in accessible place for future
More informationAOYUE SP Environment Friendly Hot Plate System INSTRUCTION MANUAL
AOYUE SP 3500 Environment Friendly Hot Plate System INSTRUCTION MANUAL Thank you for purchasing Aoyue SP3500 hot plate system. It is important to read the manual before using the equipment. Please keep
More informationInt 937. Soldering Station. Instruction Manual. Correct Disposal of this product
Int 937 Soldering Station Instruction Manual Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible
More informationAOYUE AOYUE. Soldering Station. Soldering Station. Instruction Manual. Instruction Manual
AOYUE 69 Soldering Station Instruction Manual AOYUE INTERNATIONAL LIMITED Jishui Industrial Zone, Nantou, Zhongshan City, Guangdong Province, P.R.China http://www.aoyue.com Thank you for purchasing the
More informationInt2930. Soldering Station. Instruction Manual
Int2930 Soldering Station Instruction Manual Thank you for purchasing the Aoyue Int2930 Soldering Station. Please read the manual before using the unit. Keep manual in accessible place for future reference.
More informationAOYUE. Int 852A+ pro Int 852A++ pro. SMD Rework Station INSTRUCTION MANUAL. (Centigrade / Fahrenheit switchable)
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision
More informationAOYUE INT. Advanced Repairing System NT 701A++ INSTRUCTION MANUAL. Correct Disposal of this product
This appliance can be used by children aged form 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision
More informationINT. Lead-Free Repairing System INSTRUCTION MANUAL
INT 2702 Lead-Free Repairing System INSTRUCTION MANUAL Thank you for purchasing Aoyue Int2702 Repairing System. It is important to read the manual before using the equipment. Please keep manual in accessible
More informationAOYUE 968A+ INT. Deluxe Repairing System INSTRUCTION MANUAL
AOYUE INT 968A+ Deluxe Repairing System INSTRUCTION MANUAL Thank you for purchasing Aoyue INT 968A+ Repairing System. It is important to read the manual before using the equipment. Please keep manual in
More informationAOYUE. INT 738+ (Centigrade / Fahrenheit switchable) Multi-Function Re-Working System INSTRUCTION MANUAL. Replacement Air Nozzles
BGA SOP Replacement Air Nozzles MODEL# SGL Ø 1325 Air Nozzle NOZZLE SIZE Ø 1124 2.4mm 1130 4.4mm 1194 6mm 1195 8mm 1196 7mm 1197 9mm 1198 12mm MODEL# IC SIZE L(mm) W(mm) 1010 9 9mm 10 10 1313 12 12mm 13
More informationSoldering Station INSTRUCTION MANUAL
2 9 0 0 Soldering Station INSTRUCTION MANUAL Thank you for purchasing model 2900 Soldering station. Please read manual before using the unit. Keep manual in an accessible place for future reference. Manufacturer:
More informationLead-Free Repairing System INSTRUCTION MANUAL AIR NOZZLES
AIR NOZZLES Sold Separately Lead-Free Repairing System INSTRUCTION MANUAL Thank you for purchasing model Int2738 Lead free Repairing System. Please read manual before using the unit. Keep manual in an
More information474 DESOLDERING STATION
474 DESOLDERING STATION INSTRUCTION MANUAL Thank you for purchasing 474 Desoldering Station. Please read the manual before using the unit. Keep manual in accessible place for future reference. Manufacturer:
More information474A+ TIP CARE AND USE INSTRUCTION MANUAL DESOLDERING STATION
TIP CARE AND USE. Tip Temperature High soldering temperatures can degrade the tip. Use the lowest possible soldering temperature. The excellent thermal recovery characteristics ensure efficient and effective
More informationaoyue Int732 INSTRUCTION MANUAL Game Console Reworking System
aoyue Int732 Game Console Reworking System INSTRUCTION MANUAL Thank you for purchasing Aoyue Int732 Game Console Reworking System. It is important to read the manual before using the equipment. Please
More informationSS-969 SMD Rework Station
SS-969 SMD Rework Station 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com User s Manual 1 st Edition, 2011 2011 Copy Right by Prokit
More informationUSER MANUAL TMT-HA200 HOT AIR TOOL.
USER MANUAL TMT-HA200 HOT AIR TOOL www.thermaltronics.com TABLE OF CONTENTS TMT-HA200 SPECIFICATIONS... 1 INTRODUCTION... 1 SYSTEM FEATURES... 1 SAFETY PRECAUTIONS... 2 CONTROL PANEL... 3 UNPACKING/ASSEMBLY/OPERATION...
More informationInstruction Manual. SMD Rework Station with Vacuum Pickup TABLE OF CONTENTS
SMD Rework Station with Vacuum Pickup Instruction Manual Thank you for purchasing the HAKKO FR-803 SMD Rework Station. This unit features: Digital control and display of time and temperature Display of
More informationUSER MANUAL TMT-HA300 HOT AIR TOOL.
USER MANUAL TMT-HA300 HOT AIR TOOL www.thermaltronics.com TABLE OF CONTENTS TMT-HA300 SPECIFICATIONS... 1 INTRODUCTION... 1 SYSTEM FEATURES... 1 SAFETY PRECAUTIONS... 2 CONTROL PANEL... 2 UNPACKING/ASSEMBLY/OPERATION...
More informationOPERATING MANUAL FOR LF-852DII HOT-AIR S.M.D. REWORK STATION
OPERATING MANUAL FOR LF-852DII HOT-AIR S.M.D. REWORK STATION Thank you for choosing XYTRONIC LF-852DII S.M.D. Rework Station. This tool is specially designed for soldering, desoldering Surface Mount Devices
More informationE S D REWORK SYSTEM 3 IN 1, I702 USER S GUIDE
E S D REWORK SYSTEM 3 IN 1, I702 USER S GUIDE Thank you for purchasing the Rework system. This manual describes the use and maintenance of the Rework system. Please read it before reading the manual, keep
More information34737-TL SMD REWORK STATION
34737-TL SMD REWORK STATION 1. Production Summary 1.1 Specification Rated power Input voltage Air Pump Capacity Hot Air Temperature Sensor 1.2 Function 320W AC110-130V, 60Hz Diaphragm pump 24L/min(max)
More informationOPERATION MANUAL WARNING TAIYO ELECTRIC IND.CO.,LTD. MODEL XPR-600 PREHEATER
MODEL XPR-600 PREHEATER OPERATION MANUAL WARNING Before using the XPR-600 Preheater, read the Owner's Operation Manual. Failure to follow the safety precautions and instructions in this manual could result
More informationOperating Manual. for. SMD/BGA Rework System IR860
Operating Manual for SMD/BGA Rework System IR860 Thank you for choosing XYTRONIC SOLDERLIGHT IR860 Infra-Red rework system. This appliance is specially designed for SMD/BGA rework and also very convenient
More informationSMD Rework Station with Vacuum Pickup. Instruction Manual
SMD Rework Station with Vacuum Pickup Instruction Manual Thank you for purchasing the HAKKO FR-803 SMD Rework Station. This unit features: Digital control and display of time and temperature Display of
More information474A+ INSTRUCTION MANUAL DESOLDERING STATION
1 2 7 474A+ DESOLDERING STATION INSTRUCTION MANUAL Thank you for purchasing 474A+ Desoldering Station. Please read the manual before using the unit. Keep manual in accessible place for future reference.
More informationSMD Rework Station TABLE OF CONTENTS
SMD Rework Station Thank you for purchasing the Hakko 850D SMD Rework Station. This unit features digital control and display of hot air temperature. Please read this manual before operating the Hakko
More informationSMD Rework Station with Vacuum Pickup. Instruction Manual
SMD Rework Station with Vacuum Pickup Instruction Manual l Thank you for purchasing the HAKKO FR-803B SMD Rework Station. This unit features: l Digital control and display of time and temperature l Display
More informationSoldering Station. Instruction Manual
Soldering Station Instruction Manual Thank you for purchasing the HAKKO FX-100 Soldering Station. Please read this manual before operating the HAKKO FX-100. Keep this manual readily accessible for reference.
More informationINTELLIGENT LEAD FREE SOLDERING STATION INSTRUCTION MANUAL V1.0 WARNING
3200 INTELLIGENT LEAD FREE SOLDERING STATION INSTRUCTION MANUAL V.0 WARNING ADD: Shenzhen China TEL:086-755-89575688 FAX:086-755-89574599 Website:http://www.bakon.cn E-mail:webmaster@bakon.cn Please follow
More informationInstruction Manual QUICK 855PG PROGRAMMABLE SMD REWORK STAION
QUICK 855PG PROGRAMMABLE SMD REWORK STAION Instruction Manual Thank you for purchasing our SMD Rework station. The unit is exclusively designed for reworking and soldering SMD component. Please carefully
More informationBlack Body Calibration Source User Manual
Black Body Calibration Source Surface Plate Type with External Controller Model CBB18GC- 2 WD1069 Rev B 10/23/17 Wahl Instruments Inc. 234 Old Weaverville Road Asheville, NC 28804 Toll Free: 800-421-2853
More informationHRS55PG PROGRAMMABLE SMD REWORK STAION. Instruction Manual. Thank you for purchasing our SMD Rework station. The unit is exclusively designed for
HRS55PG PROGRAMMABLE SMD REWORK STAION Instruction Manual Thank you for purchasing our SMD Rework station. The unit is exclusively designed for reworking and soldering SMD component. Please carefully read
More informationInstruction Manual TABLE OF CONTENTS
Instruction Manual Thank you for purchasing the HAKKO FM-2029 Hot Air Handpiece. Please read this manual before operating the HAKKO FM-2029. Keep this manual readily accessible for reference. CAUTION HAKKO
More informationSoldering Station. Instruction Manual
Soldering Station Instruction Manual Thank you for purchasing the HAKKO FX-100 Soldering Station. Please read this manual before operating the HAKKO FX-100. Keep this manual readily accessible for reference.
More informationHCT-900 HCT-900 HCT-900 HCT-900 HCT-900
HCT-900 HCT-900 User Guide HCT-900 Manuel d'utilisation Benutzerhandbuch des HCT-900 Guida utente del sistema HCT-900 Guía del usuario HCT-900 HCT-900 使用者指南 HCT-900 用户指南 HCT-900 ユーザーガイド HCT-900 사용설명서 1.
More informationSMD REWORK SYSTEM. Instruction Manual 401H000505
401H000505 SMD REWORK SYSTEM Instruction Manual Thank you for purchasing our SMD Rework unit. The unit is exclusively designed for reworking and soldering SMD component. Please carefully read this manual
More informationSTATIC ELIMINATOR I443A INSTRUCTION MANUAL
STATIC ELIMINATOR I443A INSTRUCTION MANUAL Thank you for purchasing a Static Eliminator. It is designed to eliminate the static charge from a charged object. Please read this manual before operating the
More informationInstruction Manual. for. Soldering / SMD Rework Station. For Lead-free soldering application and rework on professional SMD electronics.
Instruction Manual for Soldering / SMD Rework Station LF-16 1680 For Lead-free soldering application and rework on professional SMD electronics. INTRODUCTION Thank you for purchasing Xytronic s soldering
More informationDSSLF2X04H 2 IN 1. Intelligent Lead Free Soldering Station. OPERATION and MAINTENANCE MANUAL
401H000898 DSSLFX04H Intelligent Lead Free Soldering Station IN 1 OPERATION and MAINTENANCE MANUAL Thank you for purchasing a lead free soldering station. It is designed for lead free soldering. Please
More informationNOTE: All the illustrations in this manual are for explanation purposes only. Your air conditioner may be slightly different.
RADS-51J RADS-61J Owner s Manual Room Air Conditioner with R-410A Heat Controller, Inc. 15 16 Contact an authorized service technician for repair or maintenance of this unit. Contact an authorized installer
More informationInverter Split-type Room Air Conditioner
OWNER S MANUAL Inverter Split-type Room Air Conditioner Please read the operating instructions and safety precautions carefully and thoroughly before installing and operating your room air conditioner.
More informationReacti-Therm I and III Heating Modules
INSTRUCTIONS Reacti-Therm I and III Heating Modules TS-18822 TS-18824 Number TS-18822 TS-18824 Description Reacti-Therm I Heating Module (single block) Reacti-Therm III Heating Module (triple block) 2101.1
More informationHisense Refrigerator
RF697N4ZS1 Contents Safety and warning information...2 Helpful hints and tips...16 Installing your new appliance...7 Cleaning and care...17 Description of the appliance....9 Troubleshooting......18 Display
More informationGEN32 SuperBuddy Heater
GEN32 SuperBuddy Heater OWNER S MANUAL Model No. A5836 IMPORTANT SAVE THESE INSTRUCTIONS To ensure you get the best results, please read this manual first and keep it for future reference. For additional
More informationInstruction Manual. for. Intelligent Temperature Controlled Soldering Station LF-2000 (U)
Instruction Manual for Intelligent Temperature Controlled Soldering Station LF-2000 (U) For Lead-free soldering application and rework on professional SMD electronics. 1 INTRODUCTION Thank you for purchasing
More informationDR12, DR16, PO4, PO4+4
Pizza Equipment Range Operating Manual Pizza Equipment Range DR, DR6, PO, PO+ Product Range Also Includes: Induction Hobs / Combination Ovens / / Mixers Salamander Grills / Contact Grills / Pie Warmers
More informationRadiant Heater. Instruction Manual QH-200 N13275
Radiant Heater Instruction Manual QH-200 N13275 2 Contents Important Safety Instructions 3 Product Overview 6 Getting Started 7 Instructions 8 Other Useful Information 10 Important Safety Instructions
More informationAIR CONDITIONER OWNER S MANUAL. Please read this manual carefully before operating your set and retain it for future reference.
ENGLISH OWNER S MANUAL AIR CONDITIONER Please read this manual carefully before operating your set and retain it for future reference. Ceiling Suspended Original instruction ARNU18GV1A4 ARNU24GV1A4 ARNU36GV2A4
More informationThe Family Ceramic Heater
The Family Ceramic Heater 1500 Watts with Two Heat Settings Fan Only Setting Tip-Over Switch Overheating Protection Automatic Thermostat Model No.: DR-838 Owner s Manual PLEASE READ AND SAVE THESE INSTRUCTIONS
More informationBK3300/BK3300L. Intelligent Lead free Soldering Station. Instruction Manual V1.0. Warning
BK3300/BK3300L Intelligent Lead free Soldering Station Instruction Manual V1.0 Warning! Please follow the instruction to avoid accidents.! Misuse may potentially cause injury to the user or physical damage
More informationDSSHP06G Intelligent Lead Free Soldering Station INSTRUCTION MANUAL
DSSHP06G Intelligent Lead Free Soldering Station Sensor in front High frequency heating Digital Calibration Rapid recovery of temperature INSTRUCTION MANUAL Thank you for purchasing this lead free soldering
More informationMINI PARALLEL REMOVER. Iron holder with a sleep mode. Instruction Manual CAUTION
MINI PARALLEL REMOVER Iron holder with a sleep mode Instruction Manual l Thank you for purchasing the FM-2023 mini parallel remover. Please read this manual before operating the FM-2023. Keep this manual
More informationMODEL 7000 SUCTION UNIT
MODEL 7000 SUCTION UNIT OPERATOR S MANUAL Caution Federal law restricts this device to sale by or on order of a physician, or any other practitioner licensed by the law of the State in which he practices
More informationFOR THE FOLLOWING MODELS : EE-7588R EE-7588W EE-7588O EE-7588B EE-7588M
CERAMIC TOWER HEATER FOR THE FOLLOWING MODELS : EE-7588R EE-7588W EE-7588O EE-7588B EE-7588M PLEASE READ AND SAVE ALL INSTRUCTIONS TO ENSURE THE SAFE AND EFFCTIVE USE OF THIS APPLIANCE. TABLE OF CONTENTS
More informationUtopian Split A/C. Thank you for purchasing this quality Split A/C system!
Utopian Split A/C Thank you for purchasing this quality Split A/C system! Please read through this manual completely, and keep it in case you need to reference the information in the future. Any operation
More informationIonizer (Static Remover) STABLO-EX Instruction Manual
321-56879-21E Jan. 2009 For Electronic Balances Ionizer (Static Remover) STABLO-EX Instruction Manual Read the instruction manual thoroughly before you use the product. Retain this instruction manual for
More informationAIR PURIFIER CLASSIC INSTRUCTION MANUAL. CAUTION: Read manual carefully for correct procedures and proper operation.
AIR PURIFIER CLASSIC INSTRUCTION MANUAL CAUTION: Read manual carefully for correct procedures and proper operation. 1 1. Features: Specifications: Negative Ion Generation Technology Adjustable Ozone Adjustable
More information12 VELOCITY OWNER S MANUAL OPERATING INSTRUCTIONS - MAINTENANCE - SAFETY - TROUBLESHOOTING
12 VELOCITY OWNER S MANUAL OPERATING INSTRUCTIONS - MAINTENANCE - SAFETY - TROUBLESHOOTING This manual contains very important safety warnings and information. Read and save these instructions for future
More informationPOT-100C / POT-102C POT-200C /POT-202C
TAIYO ELECTRIC IND.CO.,LTD. SOLDER POT OWNER'S OPERATION MANUAL POT-100C / POT-102C POT-200C /POT-202C POT-200C OWNER'S OPERATION MANUAL Before using the solder pot, read this Owner's Operation Manual.
More informationOWNERS MANUAL. To Order Parts Call SPEED AIR MOVER
3 SPEED AIR MOVER OWNERS MANUAL IMPORTANT: READ OWNERS MANUAL CAREFULLY Please fill out and return your warranty card! MODEL # STR3SPD. REV 01 (6 12) TABLE OF CONTENTS Safety Precautions 3 Machine Operation
More informationRHMP01 MULTI PURPOSE FAN
INSTRUCTIONS & WARRANTY RHMP01 MULTI PURPOSE FAN INTRODUCTION Congratulations on purchasing a Russell Hobbs Multi-Purpose Fan. Each unit is manufactured to ensure safety and reliability. Before using this
More informationTest Equipment Depot Washington Street Melrose, MA TestEquipmentDepot.com HCT-900. HCT-900 User Guide _C
Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com HCT-900 HCT-900 User Guide 7000-3260_C 1. Warnings and Safety Instructions A fire may result if this
More informationAH-600 Baseboard Heater
AH-600 Baseboard Heater OWNERS MANUAL Read and save these instructions. A Name You Can Trust Trust has to be earned and we will earn yours. Customer happiness is the focus of our business. 2 From the factory
More informationHAKKO 703B REWORK SYSTEM TROUBLESHOOTING GUIDE
HAKKO 703B REWORK SYSTEM TROUBLESHOOTING GUIDE THIS TROUBLESHOOTING GUIDE IS DIVIDED INTO FOUR PARTS: 1. FLOW DIAGRAMS DEPICTING THE PROCESS OF ANALYZING THE PROBLEM OR PROBLEMS. 2. TABLES DEPICTING RMAL
More informationignored. Denotes content that may result in bodily injury and physical damage when ignored.
SC-201-12M, SC-201-24M Installation Manual Potential dangers from accidents during installation and use are divided into the following two categories. Closely observe these warnings, they are critical
More informationHA06. User manual. (SDO Hot Air One) HOT AIR / QUARTZ REFLOW OVEN. Version 2.21
HA06 (SDO Hot Air One) HOT AIR / QUARTZ REFLOW OVEN User manual Version 2.21 Tabel of contents IMPORTANT SAFETY RULES FORCED AIR CONVECTION OVEN... 2 Introduction.... 4 Installation.... 4 Controls explained....
More informationOwner s Manual MODEL: SCT-1. Before operating the vacuum, please read these instructions completely.
Owner s Manual MODEL: SCT-1 Before operating the vacuum, please read these instructions completely. IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be
More informationINSTRUCTION MANUAL Thermoelectric Wine Cooler MODEL: AW-210ED
INSTRUCTION MANUAL Thermoelectric Wine Cooler MODEL: AW-210ED Please carefully read and follow all safety rules and operating instructions. Product Diagram 1. HINGE 2. LIGHT 3. FAN MASK 4. SHELVES 5. FEET
More informationOWNER S MANUAL FOR ELECTRIC FRYERS. Model Numbers PARAFRYER (240V) ELECTRIC FRYER
OWNER S MANUAL FOR ELECTRIC FRYERS Model Numbers PARAFRYER 4400 9020 (240V) ELECTRIC FRYER www.manufacturedfun.com Paragon International, Inc 731 W. 18 th Street P.O. Box 560 Nevada, IA 50201 USA Phone
More informationCA3500, BA3500, CH3500 New Comfort
CA3500, BA3500, CH3500 New Comfort 6 Stage AIR PURIFIER INSTRUCTION MANUAL CAUTION: Read manual carefully for proper installation and operation. CONTENTS 2 Specifications... 2 Features... 3 Introduction...
More informationWCD-210BK. Water Dispenser OWNERS MANUAL. Read and save these instructions.
WCD-210BK Water Dispenser OWNERS MANUAL Read and save these instructions. 2 Trust has to be earned and we will earn yours. Customer happiness is the focus of our business. From the factory to the warehouse,
More informationHOUSEHOLD FREEZER 048-GM-48303/048-GM-48304/048-GM-48305
HOUSEHOLD FREEZER 048-GM-48303/048-GM-48304/048-GM-48305 TABLE OF CONTENTS NAMES OF THE PARTS 2 IMPORTANT SAFETY INSTRUCTIONS 3 INSTALLATION INSTRUCTIONS BEFORE USING YOUR FREEZER. 3 INSTALLING YOUR FREEZER
More information852 SMD REWORK SOLDERING STATION MANUAL
852 SMD REWORK SOLDERING STATION MANUAL Welcome to use SMD REWORK SOLDERING STATION/KADA 852 Produced by our factory. It is specially designed for higher efficiency and saving your time. It is very convenient
More information96 Can Beverage Cooler
96 Can Beverage Cooler ABR-960 OWNERS MANUAL Read and save these instructions. A Name You Can Trust Trust has to be earned and we will earn yours. Customer happiness is the focus of our business. From
More informationWatt-Muncher Load Bank Manual WATT-MUNCHER. Portable Load Bank. 6 June 2018 Simplex Service Page 1 of 13
WATT-MUNCHER Portable Load Bank 6 June 2018 Simplex Service 800-637-8603 Page 1 of 13 This manual was last revised: 6 June 2018 For up-to-date information on this product or others, please contact Simplex
More informationAIR CONDITIONER OWNER S MANUAL. Please read this manual carefully before operating your set and retain it for future reference.
ENGLISH FRANÇAIS ESPAÑOL OWNER S MANUAL AIR CONDITIONER Please read this manual carefully before operating your set and retain it for future reference. TYPE : Ceiling Cassette - 2Way http://www.lghvac.com
More informationINSTRUCTION MANUAL EPH-121 CONTENTS
INSTRUCTION MANUAL EPH-121 CONTENTS SAFETY PRECAUTIONS 1 NAME OF COMPONENT PARTS 5 HOW TO ASSEMBLE THE FRAME 6 OPEN AND CLOSE THE PANELS 7 OPERATION 9 TIMER OPERATION 10 SHUTDOWN 11 ROUTINE MAINTENANCE
More informationPUREPOWER SERIES CENTRAL VACUUM POWER UNITS PP500, PP600 & PP650
USER GUIDE PUREPOWER SERIES CENTRAL VACUUM POWER UNITS PP500, PP600 & PP650 AB0039 FOR RESIDENTIAL USE ONLY!! MODELS SFDB-DQ, SFDB-DR AND SFDB-DS 30042509E IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
More informationUSER MANUAL ICE MAKER
USER MANUAL ICE MAKER Model:SPP15AIM IMPORTANT SAFETY INSTRUCTIONS 2 PREPARING YOUR ICE MAKER FOR USE IMPORTANT SAFETY TIPS.. 3 GETTING TO KNOW YOUR UNIT 4 OPERATING PROCEDURES & MAINTENANCE UNPACKING
More informationLead Free Soldering Pot I100-15S
Lead Free Soldering Pot I100-15S INSTRUCTION MANUAL Thank you for purchasing the Lead Free Soldering Pot. Please read this manual before operating the unit. Store this manual in a safe, easily accessible
More informationInstruction Manual. Juice Extractor. Model: ESI Dezembro/2008
Instruction Manual Juice Extractor 36202.6- Dezembro/2008 Model: ESI 5. PROBLEMS ANALYSIS and SOLUTIONS 5. 1 Problems, Causes and Solutions The Juice Extractor Mod. ESI were designed to operate with the
More informationLow Profile. Baseboard Heater
Low Profile AH-600 Baseboard Heater OWNERS MANUAL v1.0 Read and save these instructions. 2 A Name You Can Trust Trust should be earned and we will earn yours. Customer happiness is the focus of our business.
More informationGeneral Safety Instructions
General Safety Instructions Read this manual thoroughly before first use, even if you are familiar with this type of product. The safety precautions enclosed herein reduce the risk of fire, electric shock
More information(The chances are you re never going to read me) Owner s Manual. Model S10E.
(The chances are you re never going to read me) Owner s Manual Model S10E www.simplicityvac.com 1 Contents Getting Started Important Safety Instructions 2 Polarization Instructions 3 State of California
More informationVariable Temperature Digital Solder and Desolder Station
Variable Temperature Digital Solder and Desolder Station Model: DSDS User Manual Warning This tool must be placed on its stand when not in use. A fire may result if the appliance is not used with care,
More informationOperation Manual PM-NIT-14006E
PM-NIT-14006E NittaBeltPoly Heat Press PP1535 Operation Manual Follow this manual when using NittaBeltPoly Heat Press. Please pass this manual to NittaBeltPoly Heat Press users for a safe and trouble-free
More informationMINI CERAMIC TOWER HEATER Instruction Manual
MINI CERAMIC TOWER HEATER Instruction Manual FOR MODELS: EE-7588BK, EE-7588R, EE-7588W, EE-7588GR If you have any questions about the operation of your heater, please contact Crane Customer Care. Toll
More informationInfrared Portable Space Heater
Infrared Portable Space Heater 1500 Watts with Two Heat Settings Automatic Thermostat Tip-Over Switch Room Temperature LED Display Precision Temperature Control Easy Push-Button Controls Remote Control
More informationElectric Garage Heater
Electric Garage Heater G56 OWNERS MANUAL Read and save these instructions. A Name You Can Trust Trust has to be earned and we will earn yours. Customer happiness is the focus of our business. 2 From the
More informationAir conditioner. User manual AC777KN4DCH
Air conditioner User manual AC777KN4DCH ŷ Thank you for purchasing this Samsung air conditioner. ŷ Before operating this unit, please read this user manual carefully and retain it for future reference.
More informationOperation and Maintenance Manual for the SODRTEK ST 400 Radiant Pre-Heating System P/N
Operation and Maintenance Manual for the SODRTEK ST 400 Radiant Pre-Heating System P/N 5050-0540 TITLE PAGE General Information...3 Introduction...3 Specifications...3 Physical Parameters...3 Parts Identification...4
More informationOil Panel Heater Instructions for Use
This product is only suitable for well insulated spaces or occasional use. Technical Data: Model Item No. Voltage Frequency Output (W) Protection Class OPA-60 10818 AC 230V 50/60Hz 600W I Accessories:
More informationT3/E3 Fiber Optic Line Drivers
MT618A-ST-R3 January 2004 MT619A-ST-R2 MT620AE-R2 T3/E3 Fiber Optic Line Drivers CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) FREE technical
More informationBosch Split-Type Ductless Air Conditioner / Heat Pump
Bosch Split-Type Ductless Air Conditioner / Heat Pump Climate 5000 AA Series User Manual 2 Bosch Split Type Ductless Air Conditioner / Heat Pump User Manual Data subject to change 01.2017 Bosch Thermotechnology
More informationReflux Extractor BM106. Impact Test Equipment Ltd & User Guide. User Guide
Reflux Extractor BM106 Impact Test Equipment Ltd www.impact-test.co.uk & www.impact-test.com User Guide User Guide Impact Test Equipment Ltd. Building 21 Stevenston Ind. Est. Stevenston Ayrshire KA20 3LR
More informationAB Can Beverage Cooler
AB-1200 126-Can Beverage Cooler OWNERS MANUAL Read and save these instructions. A Name You Can Trust Trust has to be earned and we will earn yours. Customer happiness is the focus of our business. 2 From
More informationDigital Heat Block User Manual
Digital Heat Block User Manual Quidel Digital Heat Block Page 1 of 10 General Information Quidel Contact Information Contact Quidel Technical Support from 8:00 a.m. to 5:00 p.m. EST Tel: 800.874.1517 (in
More informationOwners Manual Model: XXL
Corporate Office 200, 11246-163 St. Edmonton AB T5M 1Y6 Phone: 780-930-1100 Fax: 780-930-1125 Toll Free: 1-877-528-2010 www.zephyrairsystems.com AIR PURIFIER E356005 Owners Manual Model: XXL Maintenance
More information