Seda Single Lever Basin Faucet

Transcription

1 INSTALLATION MANUAL Seda Single Lever Basin Faucet FUS I toll free: I Kraus USA Inc. I REV. August 16, 2016

2 Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at and one of our representatives will e happy to help. For more information aout Kraus products, please visit: In order to activate your warranty and get faster access to customer support, please register your new Kraus product at: Sincerely, Kraus USA Customer Service 2

3 Prior to Installation: Make sure you have all necessary parts y checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at for a replacement Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any uilt up pressure. Remove existing faucet. Clean sink or countertop to remove any deris, plumer s putty, or silicone Place ucket under angle stops. Turn on angle stops to flush any deris prior to installing new pluming. Shut off angle stops Pre-drilled hole size requirement: 1 3/8 (min) Max countertop thickness: 1 3/8 For technical assistance or replacement parts, please contact Kraus Customer Service and one of our representatives will e happy to help: Toll-Free: or Customerservice@kraususa.com Tools you will need: Adjustale Wrench Phillips Screwdriver Safety Goggles Bucket 3

4 Diagram and Parts List E A F D B C1 C2 C4 G A. Faucet Body B. Base O-Ring (factory-installed) C. Mounting Hardware: C1. Ruer U-Washer C2. Metal U-Washer. Mounting Screw C4. Mounting Nut D. Hot & Cold Waterlines E. Adjustale Aerator F. Aerator Key G. Hex Wrench 4

5 Faucet Dimensions mm mm mm 5 127mm mm 6 152mm 1.37 MAX 35 mm mm mm 5

6 Lift Rod Drain Diagram and Parts List and Dimensions a c p d e f o g h i j k l m n a. Waste Stopper. Drain c. Ruer Washer d. Concave Washer e. Plastic Washer f. Mounting Nut g. Tailpipe Washer h. Tailpipe i. Top Hat Washer j. Drain Off Pole k. Washer l. Retaining Nut m. Extender Rod n. Clip o. Thum Screw p. Lift Pole 6

7 1 1/4-18UNF-2A ~ 41.3mm 27mm 1/16 ~ 1 5/8 1 Step 1: Remove mounting hardware and install waterlines C4 Step 2: Install faucet D A Remove faucet, mounting hardware, and waterlines from the ox. Remove mounting nut (C4) from mounting screw (). Place faucet ody (A) on a soft cloth, spout facing up. Secure A hot & cold waterlines (D) at the ase of the faucet (hand-tighten, then secure with ¼ turn of adjustale D wrench) A. Hot Side: Left B. Cold Side: Right Thread mounting screw () into faucet ase, flat head up, and tighten with a Phillips head screwdriver until snug (42.5 mm Max) C1 C2 C4 1 1/4-18UNF-2A A A Install faucet ody (A) through 1 3/8 hole in countertop or sink, with ase O-ring (B), hot & cold waterlines (D), and mounting screw () C4 attached 9/16-18UNEF D D C1 C2 C4 7

8 ~ 41.3mm 27mm 1/16 ~ 1 5/8 1 8B 7A Step 3: Secure faucet A (42.5 mm Max) C1 C2 C4 C4 D Install ruer U-washer (C1) and metal U-washer (C2) from underneath the countertop or sink. Attach mounting nut (C4) to mounting screw () and tighten with adjustale wrench or 10mm wrench until snug E F Step 4: Connect waterlines to main valve 8D 8A 8C 8D 8C 8B 8A 7A D Thread hot & cold waterlines (D) E onto angle stops and tighten with F adjustale wrench until snug. Turn on angle stops and check for leaks (DO NOT TURN FAUCET ON) Step 5: Install Drain i a c d e f g k h l Remove waste stopper (a) from drain (). Remove tail pipe (h), mounting nut (f), plastic washer (e), and concave washer (d) from drain (). Remove retaining nut (l) c and washer (k) from tailpipe (h) d e f Installer tip: Leave top hat washer (g) in tailpipe (h) g h 8

9 Step 5: Install Drain c d e f Install drain (), with ruer washer (c) attached, into the drain hole. Attach concave washer (d) with narrow end up, plastic washer (e), and mounting nut (f) to drain () from underneath countertop or sink. Secure tightly to sink with an adjustale wrench g h Thread tailpipe (h) onto drain () and hand-tighten. Adjust tailpipe (h) so drain off pole opening is to the rear of the sink a g h Installer Tip: Make sure tailpipe washer (g) is installed in tailpipe (h) a j k l p o n Insert waste stopper (a) into drain (). Make sure slot at end of waste stopper (a) is facing the l rear of the sink j H1 H2 H3 n m p o j l n m p o 9

10 h Step 5: Install Drain c d e f Insert lift pole rod (p) through the hole in the ack of the faucet ody. Loosen thum screw (o) and attach extender rod (m) to glift pole rod (p). Tighten thum screw h (o) p p o o m j k l n g h j k l n p o Insert shortest end of drain off pole (j) into drain aoff pole opening of tailpipe (h). Make sure drain off pole (j) and slot on waste stopper (a) engage. Attach washer (k) and p retaining nut (l) through drain off o l pole (j). Secure retaining nut (l) to n drain off pole opening of tailpipe (h) j m l j n m p o Place one end of clip (n) on drain off pole (j). Insert drain off pole (j) through desired hole of H1 extender rod (m). Place other end H2 of clip (n) H3 on drain off pole (j) Installer Tip: You may adjust the extender rod (m) to a desired height 10

11 Step6: Flush faucet E F Remove adjustale aerator (E) with aerator key (F). Turn water on for 1 minute to remove any deris. Reassemle aerator (E) and adjust to desired position Replacement Part List - FUS Metal Handle 2. Set Screw 3. Cartridge Cover 4. Cartridge Sleeve 5. Metal O-Ring 6. Ruer Washer 7. Locking Nut 8. Cartridge 9. Base O-Ring 10. Ruer U-Washer 11. Metal U-Washer 12. Mounting Nut 13. Mounting Screw 14. Adjustale Aerator 15. Aerator Key 16. Hot & Cold Waterlines 17. Hex Wrench 11

12 Replacement Part List - Lift Rod Drain 1. Waste Stopper 1 2. Drain 3. Ruer Washer 4. Concave Washer Plastic Washer 6. Mounting Nut 7. Tailpipe Washer 8. Tailpipe 9. Top Hat Washer 10. Drain Off Pole 11. Washer 12. Retaining Nut 13. Extender Rod 14. Clip 15. Thum Screw 16. Lift Pole Rod Download the Kraus Care & Maintenance Guide at: 12

13 Troule - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM 10 CAUSE ACTION Leakage under the handle Locking nut (7) has come 9 Hexagon Nut loose Loosen set screw (2) with hex wrench (17). Remove metal handle (1), cartridge cover (3), cartridge sleeve (4), metal o-ring (5) & ruer washer (6). Tighten locking nut (7) with wrench Aerator drips or has inconsistent water flow pattern Water will not shut off completely Drain is leaking Close 25 Open Aerator (14) may e dirty or not seated properly Cartridge(8) may need to e adjusted or replaced 90 Washers may e compromised or installed incorrectly Left Hot Water Unscrew aerator (14) with aerator key (15). Remove Hot Cold aerator (14) Water and clean Water out deris Loosen set screw (2) with hex wrench (17). Remove metal handle (1), cartridge cover (3), cartridge sleeve (4), metal o-ring (5) & ruer washer (6). Unscrew locking nut (7) with wrench. Remove cartridge (8). Check for cracks Check washers Push to make sure they are installed correctly and not cracked Care & Maintenance *To keep the product clean & shining, follow the steps elow: 1. Rinse with clean water & dry with a soft cloth 2. Do not clean with soaps, acid, polish, arasives, or harsh cleaners 3. Do not use cloth with a coarse surface 4. Unscrew the aerator and clean when necessary *This installation manual is suject to change without further notice. 13

14 Codes/Standards Applicale: NSF/ANSI 372 GREEN LEAD FREE I APMOR&T TM NSF/ANSI 61 ASME A M 1.2GPM 4.5L/min maximum Water Efficiency HELP LINE Our customer service hours are Monday Friday, 9am 8pm EST. Be sure to visit our wesite at If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Haror Park Drive Port Washington, NY Toll-free Customerservice@kraususa.com If you are a pluming contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Haror Park Drive Port Washington, NY Proservice@kraususa.com If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc. 12 Haror Park Drive Port Washington, NY Partnersupport@kraususa.com In requesting warranty service, please e ready to provide: 1. Proof of purchase. 2. A description of the prolem. 14

15 15

16 REGISTER YOUR PRODUCT TODAY Receive Proof of Ownership Access Customer Care & Installation Help Get Exclusive Kraus Offers & Promotions Scan to Register Online or visit We re always looking for ways to improve. Please take a moment to share your experience. Visit to let us know what you think aout your new Kraus product. Contact Us to Learn More / / customerservice@kraususa.com Like & Follow KrausUSA Download the Kraus Care & Maintenance Guide at: