Sanitary Water Tank INSTALLATION & SVC MANUAL

Transcription

1 Sanitary Water Tank INSTALLATION & SVC MANUAL MODEL : PHS Series CAUTION Before Servicing the unit, read the safety precautions in this manual. Only for authorized service personnel.

2 Sanitary Water Tank Installation/Serivce TABLE OF CONTENTS Safety precaution 1. Model Information 1.1 Single coil 1.2 Double coil 1.3 Drawing 2. Installation 3. Replacement 4. Trouble Shooting 4.1 No water flow from hot taps 4.2 Intermittent water discharge 4.3 Hot water from taps is cold 4.4 Excessive hot water from taps 5. Wiring Diagrams 6. Exploded View 6.1 PHS PHS PHS PHS

3 Safety Precaution To prevent injury to the user or other people and property damage, the following instructions must be followed. Be sure to read before installing the product. Be sure to observe the cautions specified here as they include important items related to safety. Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. WARNING CAUTION This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage to properties only. Meanings of symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. Installation Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit. There is risk of fire or electric shock. WARNING For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center. There is risk of fire or electric shock. Always ground the product. There is risk of fire or electric shock. Always install a dedicated circuit and breaker. Improper wiring or installation may cause fire or electric shock Be cautious when unpacking and installing the product. Sharp edges could cause injury. For installation, always contact the dealer or an Authorized Service Center. There is risk of fire, electric shock, explosion, or injury. Do not install the product on a defective installation stand. Be sure the installation area does not deteriorate with age. It may cause injury, accident, or damage to the product. If the base collapses, the product could fall with it, causing property damage, product failure, and personal injury

4 Operation Take care to ensure that Wires (between and sanitary water tank could not be pulled out or damaged during operation. There is risk of fire or electric shock. Do not plug or unplug Wires during operation. There is risk of fire or electric shock. Do not touch (operate) the product with wet hands. There is risk of fire or electric shock. Do not place a heater or other appliances near Wiresv. There is risk of fire or electric shock. Do not allow water to run into electric parts. There is risk of fire, failure of the product, or electric shock. Do not store or use flammable gas or combustibles near the product. There is risk of fire or failure of product. When flammable gas leaks, turn off the gas and open a window for ventilation before Turn on the product. There is risk of explosion or fire. When the product is soaked (flooded or submerged), contact an Authorized Service Center. There is risk of fire or electric shock. Be cautious that water could not be poured to the Outside of the product directly. There is risk of fire, electric shock, or product damage. Turn the main power off when cleaning or maintaining the product. There is risk of electric shock. Take care to ensure that nobody could step on or fall onto the product. This could result in personal injury and product damage

5 Installation Do not install the product where it will be exposed to sea wind (salt spray) directly. It may cause corrosion on the product. Keep level even when installing the product. To avoid vibration or water leakage. Use two or more people to lift and transport the product. Avoid personal injury. Operation Use a soft cloth to clean. Do not use harsh detergents, solvents, etc. There is risk of fire, electric shock, or damage to the plastic parts of the product. Do not step on or put anything on the product. There is risk of personal injury and failure of product. Do not insert hands or other objects into the product while it is operating. There are sharp and moving parts that could cause personal injury. Use a firm stool or ladder when cleaning or maintaining the product. Be careful and avoid personal injury

6 1. Model Information Sanitary Tank P H S Part Serial Number Number of Heating coil Electric Heater Capacity : 3kw Power Source Water Volume 20 : : 300 Power Standards 1 : 115/60/1 2 : 220/60/1 3 : /60/1 5 : 200~220/50/1 6 : 220~240/50/1 7 : 100/50(60)/1 8 : 380~415/50/3 9 : 380/60/3 A : 220/50/3 B : 208~230/60/3 C : 575/60/3 D : 440~460/60/3 E : 265/ 60/ 1 F : 200/50~60/1 G : 220~240/50,60/1 H : 220,380/50/3 J : 220,380/60/3 Sanitary Water Tank Product Name Heating AWHP P H L T A Accessary Instalation kit Part Serial Alphabet Product Category - T :Sanitary Water Tank - L :Solar Thermal System Installation Kit Product Name Heating AWHP - 6 -

7 1.1 Single coil Function and construction The Single coil is available in two capacities: 200 and 300 litres. It is a floor standing water heater which is delivered with three adjustable feet. The cold water supply is on top of the heater. The mixing valve and pressure relief valve are factory fitted. The mixing valve also functions as a stop valve towards the cold water supply. Easy draining of the heater with a drain valve on the pressure relief valve which is placed below the electric central. The Single coil has a built-in coil in stainless steel which is designed for circulation from f.ex. a solar panel. The electric element boosts the temperature whenever it is necessary. The Single coil is equipped with operation and maximum thermostat. At delivery the thermostat is set at 75 C, but it can easily be adjusted with a screwdriver. The safety temperature release is at 98 C. For electrical heating of tap water. Pressure: Max operating pressure 9 bar Temperature: Max operating temp. 85 C Balancing temp. 100 C F/R Built-in stainless steel single heat exchanger. Product description Recommended for Apartments, flats, cottages etc. Floor mounted or with a wall bracket max 200 l. Indirect and/or electric heating. Serial conn. max 6x300 l. Pressure vessel Stainless SMS steel, design pressure 10 bar, For all water qualities with chloride content less than 250 ppm. Insulation ECO Foam, water based polyurethane. ISO 3285 certification. Flame retardant and recyclable. Insulation cover White epoxy coated steel. Good protection against rough transport and corrosive environment. Electric element RG 1/4" 3 kw 1x230 Volt. For all water qualities with chloride content <250 ppm. Electric thermostat TS2 adjustable C, preset at 75 C. Safety cut-off at 98 C with reset. 30A V. Thermostat for 3 phase can be fitted. Electric central Plastic VO material in frame and cover. Splash proof IP21. Internally connected included electric cable and plug. Mixing valve Pressure relief valve User manual Environment UXT thermostatic blending valve, adjustable C, preset at 55 C. Integrated non-return and stop valve. SV2 preset and sealed at 9 bar. Factory mounted at drain connection. Easy draining prevents frost during winter. Is supplied with unit, complete with spare parts list and equipment. Zero emissions to ground, earth or water from production and regular use of product. All parts 100% recyclable. Technical data Model Name Itrs. - kw Diam. x H mm Conn. Volume heat exch. cap. Weight m 3 PHS kw ø580 x 1230 H 22 mm 198 L. 9 kw when dt 20 C 45 kg 0.42 PHS kw ø580 x 1680 H 22 mm 287 L. 9 kw when dt 20 C 59 kg

8 Technical data Single coil Quality: All units are fully CE approved. Pressure relief valve approved by NBI 06870/387. Electrical equipment is in accordance with LVD (directive for low voltage systems) and EMC (electromagnetic compatibility). List of details: Pawer wire Be connected to (Refer wiring diagram) 1. Mixing valve Adjustable temperature range (45-80 C) 2. Electric central containing: Electric element 3kW stainless steel Incoloy 825 Thermostat C Safety temperature release 98 C 3. Indirect heating coil Stainless steel Duplex LDX Pressure relief valve 9 bar Drain valve On the pressure relief valve PHS PHS Connection to the vvx flow/return PHS and PHS is 3 /4. Internal thread from pressure relief valve is 3 /4. Installation important! The heater must be filled with water before the electricity is connected. Otherwise the warranty does not apply. If the heater is installed but not in use, it must be flushed with water once a week. Electrical connections technical data: Electric element: RG 3 kw 230V 1 phase, 1 1 /4 connection with O-ring seal Thermostat: Adjustable C. Safety cut-off: 98 C Electric central: Internally connected from factory. Splash proof IP21. Electric cable: 2,3 mtrs cable. Output >3kW or when 230V 1 phase is installed requires fixed connection For installation in sanitary rooms special regulations apply. Warning Do not remove the factory fitted pressure relief valve (9 bar). The valve must have a free flowing, non closeable 1/2 outlet to a visible and frost free drain! All alterations or repair concerning the electrical equipment must be performed by authorized electricians only, and in accordance with the diagrams shown. All connections must be pulled tight. This must be repeated after approximately 3 months operation

9 1.2 Double coil F/R Function and construction The Double coil is available in two capacities: 200 and 300 litres. It is a floor standing water heater which is delivered with three adjustable feet. The cold water supply is on top of the heater. The mixing valve and pressure relief valve are factory fitted. The mixing valve also functions as a stop valve towards the cold water supply. Easy draining of the heater with a drain valve on the pressure relief valve which is placed below the electric central. The Double coil has built-in twin coils in stainless steel which are designed for circu-lation from a solar panel in f.ex. one coil and another heating source in the other coil. The electric element boosts the temperature whe-never it is necessary. The Double coil is equipped with operation and maximum thermostat. At delivery the thermostat is set at 75 C, but it can easily be adjusted with a screwdriver. The safety temperature release is at 98 C. For electrical heating of tap water. Pressure: Max operating pressure 9 bar Temperature: Max operating temp. 85 C Balancing temp. 100 C Built-in stainless steel double heat exchangers Product description Recommended for Apartments, flats, cottages etc. Floor mounted or with a wall bracket max 200 l. Indirect and/or electric heating. Serial conn. max 6x300 l. Pressure vessel Stainless SMS steel, design pressure 10 bar, For all water qualities with chloride content less than 250 ppm. Insulation ECO Foam, water based polyurethane. ISO 3285 certification. Flame retardant and recyclable. Insulation cover White epoxy coated steel. Good protection against rough transport and corrosive environment. Electric element RG 1 1 /4 3 kw 1x230 Volt. For all water qualities with chloride content <250 ppm. Electric thermostat TS2 adjustable C, preset at 75 C. Safety cut-off at 98 C with reset. 30A V. Thermostat for 3 phase can be fitted. Electric central Plastic VO material in frame and cover. Splash proof IP21. Internally connected included electric cable and plug. Mixing valve UXT thermostatic blending valve, adjustable C, preset at 55 C. Integrated non-return and stop valve. Pressure relief valve SV2 preset and sealed at 9 bar. Factory mounted at drain connection. Easy draining prevents frost during winter. User manual Is supplied with unit, complete with spare parts list and equipment. Environment Zero emissions to ground, earth or water from production and regular use of product. All parts 100% recyclable. Technical data Model Name Itrs. - kw Diam. x H mm Conn. Volume heat exch. cap. Weight m 3 PHS kw ø580 x 1230 H 22 mm 198 L. 9 kw + 6kW 50 kg 0.42 PHS kw ø580 x 1680 H 22 mm 287 L. 9 kw + 6kW 64 kg

10 Technical data Double coil Quality: All units are fully CE approved. Pressure relief valve approved by NBI 06870/387. Electrical equipment is in accordance with LVD (directive for low voltage systems) and EMC (electromagnetic compatibility). List of details: 1. Pawer wire Be connected to (Refer wiring diagram) 2. Mixing valve Adjustable temperature range (45-80 C) 3. Electric central containing: Electric element 3kW stainless steel Incoloy 825 Thermostat C Safety temperature release 98 C 4. Indirect heating coil Stainless steel Duplex LDX Pressure relief valve 9 bar Drain valve On the pressure relief valve PHS PHS Connection to the vvx flow/return PHS and PHS is 3 /4. Internal thread from pressure relief valve is 3 /4. Installation important! The heater must be filled with water before the electricity is connected. Otherwise the warranty does not apply. If the heater is installed but not in use, it must be flushed with water once a week. Electrical connections technical data: Electric element: RG 3 kw 230V 1 phase, 1 1 /4 connection with O-ring seal Thermostat: Adjustable C. Safety cut-off: 98 C Electric central: Internally connected from factory. Splash proof IP21. Electric cable: 2,3 mtrs cable. Output >3kW or when 230V 1 phase is installed requires fixed connection For installation in sanitary rooms special regulations apply. Warning Do not remove the factory fitted pressure relief valve (9 bar). The valve must have a free flowing, non closeable 1/2 outlet to a visible and frost free drain! All alterations or repair concerning the electrical equipment must be performed by authorized electricians only, and in accordance with the diagrams shown. All connections must be pulled tight. This must be repeated after approximately 3 months operation

11 1.3 Drawing PHS / PHS PHS PHS

12 PHS / PHS PHS PHS

13 2. INSTALLATION Conditions where Sanitary Water Tank is Installed Specific conditions are required for installation place such as service space, water pipe length and height, total volume of water and water quality. General Considerations The installation location is frost-free. Make sure to make the piping in size 1" or more (and reduce to 3 /4" at the inlet of the tank) as to have sufficient water volume in the piping between indoor unit and sanitary water tank. Locate the sanitary water tank in a suitable position to facilitate ease of maintenance, remember access is required to the electrical box. Provide a connection for the relief valve blow-off and drain. To avoid back siphonage it is advised to install a non-return valve on the water inlet of the sanitary water tank in accordance with local and national regulations. Take care that in the event of a leak, water can not cause any damage to the installation space and surroundings. Installing Sanitary Water Tank 1. Check if all sanitary water tank accessories are enclosed. 2. When floor mounting, place the sanitary water tank on a level surface. And make sure the sanitary water tank is mounted level. 3. Apply thermal paste to the thermistor and insert the thermistor as deep as possible in the thermistor socket. Fix using the nut provided. Sanitary Water Tank and Sanitary Water Tank Kit/Solar Thermal Kit To establish sanitary water circuit, 3way control valve and sanitary water tank kit is required. If solar thermal system is pre-installed at the installation field, solar thermal kit is required to interface solar thermal system to sanitary water tank to General Information supports following 3way valve. Type Power Operating Mode Supported SPDT 3-wire (1) 230V AC Selecting Flow A between Flow A and Flow B (2) Selecting Flow B between Flow A and Flow B (3) Yes Yes (1) : SPDT = Single Pole Double Throw. Three wires consist of Live1 (for selecting Flow A), Live 2 (for selecting Flow B), and Neutral (for common). (2) : Flow A means water flow from the indoor unit to under floor water circuit. (3) : Flow B means water flow from the indoor unit to sanitary water tank

14 How to Install Sanitary Water Tank PHS / PHS PHS / PHS

15 How to Install Sanitary Water Tank Kit Follow below procedures Step 1a ~ Step 6. Step 1. Find a relay contactor and ELB in the kit. Bolt them into control box. (symbol at picture) Step 2. Connect CN_B/HEAT(A) (White Connector) of the indoor unit PCB with relay contact using included cable (symbol at the picture). Connect relay contactor port no. 0 and 1. Step 3. Connect relay contactor port no. 2 and 4 with ELB port no. 2 and 4. (symbol at the picture). B Check Polarity Connect relay contact port no. 2 to ELB port no. 2 Connect relay contact port no. 4 to ELB port no. 4 Step 4. Connect relay contactor port no. 3 and 5 with terminal block 1 port 6 and 7. (symbol at the picture). Check Polarity Connect relay contact port no. 3 to terminal block 1 port 6 Connect relay contact port no. 5 to terminal block 1 port 7 C D A Step 5. Connect ELB port no. 1 and 3 with terminal block 3 port 3 and 4. (symbol at the picture). Check Polarity Connect ELB port no. 1 to terminal block 3 port 3 Connect ELB port no. 3 to terminal block 3 port 4 A E Relay contactor port no. assignment 2 4 ELB port no. assignment

16 Step 6. Find sanitary water tank sensor. Connect it to CN_TH4 (Red Connector) of the indoor unit PCB (symbol at the picture). The sensor wire should be passed through holes for sensor (symbol and at the picture). The sensor should be mounted correctly to the sensor hole of sanitary water tank. Sensor mounting Insert sensor into sensor socket and bolt it tightly. A B C D Sanitary Water Tank

17 How to Wire Sanitary Water Tank Heater Step 1. Uncover heater cover of the sanitary water tank. It is located side of the tank. Step 2. Find terminal block and connect wires as below. Wires are field-supplied item. WATER TANK HEATER 6 L 7 N BR BL (L) (N) (L) : Live signal from PCB to Heater (N) : Neutral signal from PCB to Heater Wire specification Cross-sectional area of the wire should be 5mm 2. Adjusting thermostat temperature To guarantee proper operation, it is recommended to set temperature of thermostat to maximum temperature (symbol at the picture). A

18 3.Replacement WARNING Incorrect handling of safety valves, thermostat and other valves may lead to tank rupture. Follow instructions carefully: 1. Always turn off main power (8) when water supply is shut off. 2. Test free operation of safety valves regularly by opening valves and ensuring that water runs out. 3. Electrical connection and repair operations should only be carried out by an authorized electrician. 4. Fitting and repair of plumbing fixtures should only be carried out by an authorized plumber. 5. When replacing thermostats, safety valves and other valves supplied with this unit, use only approved parts of same specification. CAUTION: Remember before resetting the safety cut-off or altering the thermostat setting, isolate electrical supply to the unit prior to removal of the electrical box lid. CAUTION: If electric element (5) or thermostat (4) is defective, contact authorized electrician. CAUTION: After adjustments are completed, ensure the lid to the electrical box is replaced correctly and the retaining screw is fitted. Replacement of the heating element 1. Disconnect the power cable (8). 2. Remove the electric lid (3) in front of the electric box. 3. Shut valve (1) fully towards clockwise until the valve is completely closed. 4. Open safety relief valve (10). (Close the valve by turning counter clockwise until it clicks.) 5. Loosen screw X and disable the wires. 6. Remove the heating element (5) with the element socket tool Y. A certain amount of water will now come out of the element hole. 7. Quickly rinse the O-ring slot and get ready to install the new heating element (5). 8. Enter the new heating element with a new O-ring seal. IMPORTANT: Make sure that the element enters the thread ring freely and tighten. 9. Open valve (1) and check that the heating element is not leaking. 10. Mount the wires X and Y and tighten properly. 11. Reconnect the power cable (8). Adjust the mixing valve (see "Installation and directions for use")

19 Replacement of the thermostat 1. Remove the electric lid (3) in front of the electric box. 2. Loosen the 4 screws X and Y and disable the wires X and Y. 3. Remove the thermostat (4) and replace this with a new one. 4. Mount the wires X and Y properly. Reset button Safety cut-out Thermostat Temperature adjustment Electric element 5/4"

20 4. Trouble Shooting No water flow from hot taps FAULT POSSIBLE CAUSE REMEDY 1. Mains supply off. 2. Strainer blocked. 3. Cold water inlet Pressure Reducing Valve incorrectly fited. 1. Check and open stopcock. 2. Turn off water supply. Remove strainer and clean. (See Pressure Reducing Valve page 6 Installation Manual) 3. Check and refit as required, (see item 3 page 5of installation manual). Water from hot taps is cold. Intermittent water discharge. Continuous water discharge. 1. Immersion heaters not switched on. 2. Immersion heater thermal cut-out has operated. 3. Programmer set to central heating or not switched on. 4. Boiler not working. 5. Cylinder thermal cut-out has operated. (Indirect units only). 6. Motorised valve not operating correctly. 1. Reduced internal expansion. 2. Thermal control failure. (Note Water will be hot). 1. Cold water inlet Pressure Reducing Valve not working. 2. Temperature and pressure relief valve faulty. 3. Expansion relief valve not working correctly. 1. Check and switch on. 2. Check and reset button. (See thermostat diagram page 9 and safty cut-out on page 4 of installation manual). 3. Check and set to hot water. 4. Check boiler operation. If fault suspected consult installer or boiler manufacturer. 5. As at No Check wiring and /or plumbing connections to motorised valve. (See pages 8 or 10 of the installation manual). 1. Recharge "air gap" (See cold water discharge on page 4 of installation manual). 2. Switch off power to immersion heater(s) and boiler supply to the unit. When discharge has stopped, check thermal controls, replace if faulty. Contact a competent person. 1. Check pressure from valve if greater than 2.1 bar replace. (See page 6 of installation manual). 2. As No. 2 of above. 3. Check and replace if faulty. (See page 6 of installation manual). Note : Disconnect electrical supply before removing any electrical equipment covers

21 4.1 No water flow from hot taps Start Mains supply off NO Line strainer blocked NO Cold water PRV incorrectly fittted Open supply valve Clear line strainer Check and refit as required If problem still persists contact a competent engineer 4.2 Intermittent water discharge Start Reduced Internal expansion volume NO Cold water PRV incorrectly fittted Recharge "air gap". Follow correct procedure If problem still persists contact a competent engineer / plumber Switch off power to immersion heaters and boiler supply to the unit. When discharge has stopped check thermal controls and replace as necessary

22 4.3 Hot water from taps is cold Start DIRECT Start INDIRECT Are immersion heaters switched on Has immersion heater thermal cut-out operated? Is the programmer set to central heating or not switched on NO Is the boiler working? NO NO Switch on immersion heaters Check and reset button Check and set to hot water programme. Is the motorised valve operating connections NO Has cylinder thermal cut-out operated? Check wiring or plumbing connections Check and reset button If problem still persists contact a competent engineer / plumber 4.4 Excessive Hot water from taps Start NO Connect wiring as per instructions Is Thermostat wired as per layouts for "S" or "Y" plan installation Cylinder Thermostat set to high NO Check cylinder thermostat is switching on & off with programmer & hot water NO Reduce Temperature setting Faulty thermostat replace Wiring Fault Seek advice from electrician Is 2-port motorised valve closing when cylinder reaches temperature? NO Check wiring on cylinder thermostat

23 5. Wiring Diagrams

24 6. Exploded view 6.1 PHS / PHS No Part Name Part Number Remark 1 Electric Heater MEE (71259) Mixing valve MJX (90040) Thermistor pocket MEG (81020) Safety valve MJX (90420) Anode bar MAK (56200) Thermostat EBG (80060)

25 6.2 PHS / PHS No Part Name Part Number Remark 1 Electric Heater MEE (71259) Mixing valve MJX (90040) Thermistor pocket MEG (81020) Safety valve MJX (90420) Anode bar MAK (56200) Thermostat EBG (80060)

26 P/NO : MFL December,