GLO-RAY Round Heated Stone Shelf with Display Lamp GRSSR20-DL & GRSSR20-DLH Series Installation & Operating Manual

Transcription

1 GLO-RAY Round Heated Stone Shelf with Display Lamp GRSSR20-DL & GRSSR20-DLH Series Installation & Operating Manual I&W # This manual contains important safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury. If you re unable to understand the contents of this manual, please bring it to the attention of your supervisor. Do not operate this equipment unless you have read and understood the contents of this manual. Este manual contiene importante información sobre seguridad concerniente al mantenimiento, uso y operación de este producto. Cualquier falla en el seguimiento de las instrucciones contenidas en este manual puede resultar en un serio daño. Si usted no puede entender el contenido de este manual por favor pregunte a su supervisor. No opere este equipo al menos que haya leído y comprendido el contenido de este manual.

2 CONTENTS Important Owner Information...i Introduction...i Important Safety Information...1 Model Description...3 All Models...3 GRSSR20-DL (Standard Wattage)...3 GRSSR20-DLH (High Wattage)...3 Model Designation...3 Specifications...4 Electrical Rating Chart...4 Plug Configuration...4 Dimensions...4 Installation...5 Unpacking...5 Location...5 Operation...6 Maintenance...7 General...7 Cleaning...7 Cleaning for Swanstone Solid Surface...7 Cleaning for Decorative Lamp...7 Heat Bulb Replacement...8 Accessories...9 Cutting Board/Carving Station...9 Troubleshooting...10 Hatco Limited Warranty...11 Authorized Parts Distributors...Back Cover IMPORTANT OWNER INFORMATION Record the model number, serial number (located on the side of the unit), voltage and purchase date of your Round Heated Stone Shelf with Display Lamp in the spaces below. Please have this information available when calling Hatco for service assistance. Model No. Serial No. Voltage Date of Purchase INTRODUCTION Hatco Glo-Ray Round Heated Stone Shelf with Display Lamp is designed to keep hot food at optimum serving temperatures and to enhance restaurant decor. Heat is focused directly above and below, providing effective insulation for prolonged serving times. Hatco foodwarmers are quality built to meet the demands of foodservice operations and provide years of trouble-free performance. This manual provides the installation, safety and operating instructions for the Glo-Ray Round Heated Stone Shelf with Display Lamp. We recommend all installation, operating and safety instructions appearing in this manual be read prior to installation or operation of your foodwarmer. Safety instructions Business Hours: 8:00 a.m. to 5:00 p.m. Central Standard Time (Summer Hours: June to September 8:00 a.m. to 5:00 p.m. C.D.T. Monday through Thursday 8:00 a.m. to 2:30 p.m. C.D.T. Friday) Telephone: (800) ; (414) Fax: (800) (Parts & Service) (414) (International) 24-Hour 7-Day Parts & Service Assistance available in the United States and Canada by calling (800) Additional information can be found by visiting our web site at that appear in this manual after a warning symbol and the words or CAUTION printed in bold face are very important. means there is the possibility of serious personal injury or death to yourself or others. CAUTION means there is the possibility of minor or moderate injury. NOTICE without the symbol signifies the possibility of equipment or property damage only. Hatco Glo-Ray Round Heated Stone Shelf with Display Lamp is a product of extensive research and field testing. The materials used were selected for maximum durability, attractive appearance and optimum performance. Every unit is thoroughly inspected and tested prior to shipment. Form No. GRSSRDLM-0607 i

3 IMPORTANT SAFETY INFORMATION IMPORTANT! Read the following important safety information to avoid personal injury or death, and to avoid damage to the equipment or property. S For safe and proper operation, plug unit into a properly grounded electrical outlet of the correct voltage, wire size and plug configuration. If the plug and receptacle do not match, contact a qualified electrician to determine the proper voltage and size and to install the proper electrical outlet. The Glo-Ray Round Heated Stone Shelf with Display Lamp is not waterproof. To avoid electrical shock or personal injury DO NOT submerge in water. Do not operate if it has been submerged in water. Do not steam clean. To avoid any injury, turn the power switch OFF, unplug the unit from the power source and allow to cool completely before performing any maintenance or cleaning. To avoid any injury, turn the power supply OFF to the mounting location before installing. For safe and proper operation, the unit must be located at 1" (25.4 mm) distance from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. To prevent any injury or damage to the unit do not pull unit by power cord. To prevent any injury, discontinue use if power cord is frayed or worn. Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. S GRSSR20-DL standard watt heat lamps (250 watt bulb) must have a minimum of 16" (406 mm) above a flammable surface. If safe distances are not maintained, discoloration or combustion could occur. GRSSR20-DLH high watt heat lamps (375 watt bulb) must have a minimum of 27" (686 mm) above a flammable surface. If safe distances are not maintained, discoloration or combustion could occur. For safe and proper operation, do not install a 375 watt bulb into a GRSSR20-DL standard watt unit. If service is required on this unit, contact your Authorized Hatco Service Agent, or contact the Hatco Service Department at or ; fax or International fax This product has no user serviceable parts. To avoid damage to the unit or injury to personnel, use only Authorized Hatco Service Agents and Genuine Hatco Replacement Parts when service is required. Genuine Hatco Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Hatco Replacement Parts when repairing Hatco equipment. Failure to use Hatco Replacement Parts may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn. 1 Form No. GRSSRDLM-0607

4 IMPORTANT SAFETY INFORMATION IMPORTANT! Read the following important safety information to avoid personal injury or death, and to avoid damage to the equipment or property. CAUTIONS Damage to the countertop material caused by heat generated from Hatco equipment is not covered under the Hatco Warranty. Contact the manufacturer of the base material for application information. To avoid any injury or damage locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit and food. CAUTIONS Unit is not weatherproof. For safe and proper operation locate the unit indoors where the ambient air temperature is constant and is a minimum of 70 F (21 C). Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. NOTICES Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish of your unit, marring its appearance and making it susceptible to dirt accumulation. Form No. GRSSRDLM

5 MODEL DESCRIPTION ALL MODELS Hatco s Glo-Ray Round Heated Shelf with Display Lamp features a thermostatically controlled Swanstone base available in stone colors of Gray Granite, Bermuda Sand, Night Sky and Sawgrass; and display lamp offering Designer colors in Warm Red, Black, Gray Granite, White Granite, Navy Blue and Hunter Green. Each foodwarmer comes equipped with an On/Off (lighted) rocker switch, adjustable thermostat and 6' (1829 mm) power cord with attached plug. GRSSR20-DL (Standard Wattage) Standard wattage models (DL) feature a 250 watt upper infrared heat bulb. GRSSR20-DLH (High Wattage) High wattage models (DLH) feature a 375 watt upper infrared heat bulb. Figure 1. Model GRSSR20-DL MODEL DESIGNATION GR SS R 20 - DL H Glo-Ray Stone Shelf Round Shelf Diameter Inches Distance between Upper Lamp and Heated Base Shade Style High Watt Decorative Lamp Figure 2. Model Designation 3 Form No. GRSSRDLM-0607

6 SPECIFICATIONS ELECTRICAL RATING CHART Model Voltage Wattage Amperage Plug Configuration Shipping Weight GRSSR20-DL NEMA 5-15P GRSSR20-DLH NEMA 5-15P 40 lbs. (18 kg) 40 lbs. (18 kg) PLUG CONFIGURATION Units are supplied from the factory with a 6' (1.8 m) electrical cord and plug installed. (See Figure 3.) For safe and proper operation, plug unit into a properly grounded electrical outlet of the correct voltage, wire size and plug configuration. If the plug and receptacle do not match, contact a qualified electrician to determine the proper voltage and size and install the proper electrical outlet. NEMA 5-15P Figure 3. Plug Configuration * Receptacle not supplied by Hatco. * DIMENSIONS 34-1/2" (876 mm) Standard Watt 45-1/2" (1156 mm) High Watt Dia. 20" (508 mm) 16" (406 mm) Standard Watt 27" (686 mm) High Watt 2-5/8" (65 mm) Figure 4. Dimensions Form No. GRSSRDLM

7 INSTALLATION UNPACKING The Glo-Ray Round Heated Stone Shelf with Display Lamp is shipped pre-assembled and ready for operation. Care should be taken when unpacking shipping carton to avoid damage to unit and components enclosed. To prevent any injury or damage to the unit do not pull unit by power cord. To prevent any injury, discontinue use if power cord is frayed or worn. 1. Remove unit from box. 2. Remove information packet. To prevent delay in obtaining warranty coverage, fill out and mail in the warranty card. 3. Remove protective paper from all surfaces before placing into service. LOCATION NOTE: Unit must be transported in the upright position. CAUTION To avoid any injury or damage locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit and food. To avoid any injury or damage to the unit(s) connect to a properly grounded electrical supply. Contact a qualified electrician to determine the proper voltage, wire size and installation method. The Glo-Ray Round Heated Stone Shelf with Display Lamp must have a minimum of 1" (25 mm) clearance along the sides of combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. For proper operation and maximum performance, locate the Glo-Ray Round Heated Stone Shelf with Display Lamp in an area where the ambient air temperature is constant and is a minimum of 70 F (21 C). Areas which are susceptible to active air movements or currents should be avoided, i.e., near exhaust fans or hoods and air conditioning ducts. CAUTION Unit is not weatherproof. For safe and proper operation the unit must be located indoors where the ambient air temperature is a minimum of 70 F (21 C) and a maximum of 85 F (29 C). 1" (25.4 mm) 1" (25.4 mm) For safe and proper operation, the unit must be located at 1" (25.4 mm) distance from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. Figure 5. Minimum Clearance from Combustibles 5 Form No. GRSSRDLM-0607

8 OPERATION Plug unit into a properly grounded electrical outlet of the correct voltage, size and plug configuration. If the plug and receptacle do not match, contact a qualified electrician to determine the proper voltage and size and install the proper electrical outlet. CAUTION Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. CAUTION Unit is not weatherproof. For safe and proper operation locate the unit indoors where the ambient air temperature is a minimum of 70 F (21 C). 1. Plug unit into a properly grounded electrical outlet of the correct voltage, size and plug configuration. See SPECIFICATIONS for details. 2. Place the Power ON/OFF Switch in the ON position. See Figure 6. The heat bulb will light when the unit is energized. 3. Turn the thermostat to the desired heated stone base temperature setting. Base temperature range is F (38 93 C). 4. Allow unit 30 minutes to reach operating temperature. The Glo-Ray Round Heated Stone Shelf with Display Lamp is not waterproof. To avoid electrical shock or personal injury DO NOT submerge in water. Do not operate if it has been submerged in water. Power Cord Shelf Thermostat Power ON/OFF Switch Figure 6. Controls Form No. GRSSRDLM

9 MAINTENANCE GENERAL The Hatco Glo-Ray Round Heated Stone Shelf with Display Lamp is designed for maximum durability and performance, with minimum maintenance. To avoid any injury or damage to the unit turn the power switch OFF, unplug the unit and allow to cool before performing any maintenance or cleaning. CLEANING General To preserve the finish of the Glo-Ray Round Heated Stone Shelf with Display Lamp, it is recommended that the surfaces be wiped daily with a damp cloth. The Glo-Ray Round Heated Stone Shelf with Display Lamp is not waterproof. To avoid electrical shock or personal injury or damage to the unit DO NOT submerge or saturate with water. Do not operate if it has been submerged or saturated with water. CLEANING FOR SWANSTONE SOLID BASE SURFACE Use of the following products will not damage the Swanstone Solid Surface. Follow the directions on the product labels. If these methods fail to produce acceptable results, contact the Swanstone representative in your area. Hard to Remove Stains For hard to remove stains, abrasive cleaners recommended include Ajax, Comet, Bon Ami, or Bar Keeper s Friend. Also, the use of an abrasive pad such as Scotch-Brite. NOTE: Do not use steel wool or metal scouring pads. Mineral Based Stains For a mineral based stain, cleaners designed to remove iron or rust are recommended and should not harm Swanstone. Scratches For scratches use sandpaper starting with coarsest grit and going to finest grit until scratch disappears. Blend area in with abrasive finishing pad. If service is required on this unit, contact your Authorized Hatco Service Agent, or contact the Hatco Service Department at or ; fax or International fax This product has no user serviceable parts. To avoid damage to the unit or injury to personnel, use only Authorized Hatco Service Agents and Genuine Hatco Replacement Parts when service is required. Genuine Hatco Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Hatco Replacement Parts when repairing Hatco equipment. Failure to use Hatco Replacement Parts may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn. CLEANING FOR DECORATIVE LAMP To preserve the finish of the upper Decorative Heat Lamp it is recommended that the lamp shade surface be wiped daily with a soft damp cloth. Stubborn stains can be removed with a mild nonabrasive cleaner. To avoid electrical shock or personal injury, do not steam clean or use excessive water on the unit. To avoid any injury or electrical shock, turn the power switch and the fuse disconnect switch/circuit breaker off. Allow to cool completely before performing any maintenance or cleaning. NOTICE Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish of your Decorative Heat Lamp, marring its appearance and making it susceptible to dirt accumulation. 7 Form No. GRSSRDLM-0607

10 MAINTENANCE HEAT BULB REPLACEMENT Each standard wattage Decorative Heat Lamp (DL) is supplied with one clear, uncoated infrared heat bulb rated at 250 watts. Each high wattage Decorative Heat Lamp (DLH) is supplied with one clear, uncoated infrared heat bulb rated at 375 watts. 250 watt bulbs may also be used in DLH units. For safe and proper operation, do not install a 375 watt bulb into a DL standard watt lamp. 1. To replace a bulb, place the switch in the OFF position and allow the bulb to cool completely. 2. Bulbs have a threaded base. Unscrew the heat bulb counterclockwise from the unit and replace with a new bulb. The following replacement bulbs are available from the factory or Hatco Authorized Parts Distributor. DL (standard wattage) 250 Watt 120V Red Coated Watt 120V Clear Coated Watt 120V Red Uncoated Watt 120V Clear Uncoated DLH (high wattage) 375 Watt 120V Clear Uncoated Watt 120V Red Uncoated Watt 120V Clear Coated Watt 120V Red Coated Form No. GRSSRDLM

11 ACCESSORIES CUTTING BOARD/CARVING STATION Made of NSF Approved food safe materials. Installation Cutting board comes with rubber feet on bottom to fit right on top of base. Material Made of same material as Swanstone base. Colors Available in the same colors as the base, Gray Granite, Bermuda Sand, Night Sky and Sawgrass. Size 21" (533 mm) wide by 15-3/4" (400 mm) deep Cutting Board CLEANING FOR SWANSTONE CUTTING BOARD SURFACE Use of the following products will not damage the Swanstone Solid Surface. Follow the directions on the product labels. If these methods fail to produce acceptable results, contact the Swanstone representative in your area. Hard to Remove Stains For hard to remove stains, abrasive cleaners recommended include Ajax, Comet, Bon Ami, or Bar Keeper s Friend. Also, the use of an abrasive pad such as Scotch-Brite. NOTE: Do not use steel wool or metal scouring pads. Figure 7. Cutting Board Mineral Based Stains For a mineral based stain, cleaners designed to remove iron or rust are recommended and should not harm Swanstone. Scratches For scratches use sandpaper starting with coarsest grit and going to finest grit until scratch disappears. Blend area in with abrasive finishing pad. 9 Form No. GRSSRDLM-0607

12 TROUBLESHOOTING To avoid any injury or damage, the Heated Stone Shelf must only be serviced by qualified personnel. To avoid any injury or damage to the unit turn the power switch OFF, unplug the unit and allow to cool before performing any maintenance or cleaning. SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Unit too hot. Base thermostat control set too high. Adjust thermostat control to a lower setting. Base thermostat control stuck in the ON position. Unit plugged into an incorrect power supply. Contact Authorized Service Agency for repair. Verify with qualified personnel that power supply matches unit specification. Unit not hot enough. Base thermostat control set too low. Adjust thermostat control to a higher setting. Location of unit is susceptible to air currents (air conditioning ducts or exhaust fans). Block air currents or relocate unit. Upper infrared heat bulb does not light. Bulb is defective. Replace heat bulb. Unit not working at all. Unit not plugged in. Plug unit into proper power supply. Unit not turned on. ON/OFF switch is not functioning. Base heating element is burned out. Base thermostat control is defective. Place ON/OFF switch in the ON position. Contact Authorized Service Agent for repair. Contact Authorized Service Agent for repair. Contact Authorized Service Agent for repair. Form No. GRSSRDLM

13 HATCO LIMITED WARRANTY 1. PRODUCT WARRANTY Hatco warrants the products that it manufactures (the Products ) to be free from defects in materials and workmanship, under normal use and service, for a period of one (1) year from the date of purchase when installed and maintained in accordance with Hatco s written instructions or 18 months from the date of shipment from Hatco. Buyer must establish the product s purchase date by returning Hatco s Warranty Registration Card or by other means satisfactory to Hatco in its sole discretion. Hatco warrants the following Product components to be free from defects in materials and workmanship from the date of purchase (subject to the foregoing conditions) for the period(s) of time and on the conditions listed below: THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without limiting the generality of the foregoing, SUCH WARRANTIES DO NOT COVER: Coated incandescent light bulbs, fluorescent lights, lamp warmer heat bulbs, glass components, Product failure in booster tank, fin tube heat exchanger, or other water heating equipment, caused by liming, sediment buildup, chemical attack or freezing, Product misuse, tampering or misapplication, improper installation or application of improper voltage. a) One (1) Year Parts and Labor PLUS One (1) Additional Year Parts-Only Warranty: Toaster Elements (metal sheathed) Drawer Warmer Elements (metal sheathed) Drawer Warmer Drawer Rollers and Slides Food Warmer Elements (metal sheathed) Display Warmer Elements (metal sheathed air heating) Holding Cabinet Elements (metal sheathed air heating) Built-In Heated Well Elements (metal sheathed) b) One (1) Year Parts and Labor PLUS Four (4) Years Parts-Only Warranty on pro-rated terms that Hatco will explain at Buyer s request: 3CS and FR Tanks c) One (1) Year Parts and Labor PLUS Nine (9) Years Parts-Only Warranty on: Electric Booster Heater Tanks Gas Booster Heater Tanks 2. LIMITATION OF REMEDIES AND DAMAGES Hatco s liability and Buyer s exclusive remedy hereunder will be limited solely, at Hatco s option, to repair or replacement by a Hatco-authorized service agency (other than where Buyer is located outside of the United States, Canada, United Kingdom or Australia in which case Hatco s liability and Buyer s exclusive remedy hereunder will be limited solely to replacement of part under warranty) with respect to any claim made within the applicable warranty period referred to above. Hatco reserves the right to accept or reject any such claim in whole or in part. Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer s sole expense. HATCO WILL NOT BE LIABLE, UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS RESULTING FROM THE USE OF OR INABILITY TO USE THE PRODUCTS OR FROM THE PRODUCTS BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY OTHER PRODUCT OR GOODS. 11 Form No. GRSSRDLM-0607

14 NOTES: Form No. GRSSRDLM

15

16 HATCO AUTHORIZED PARTS DISTRIBUTORS ALABAMA Jones McLeod Appl. Svc. Birmingham ARIZONA Auth. Comm. Food Equip. Phoenix Byassee Equipment Co. Phoenix CALIFORNIA Industrial Electric Commercial Parts & Service, Inc. Huntington Beach Chapman Appl. Service San Diego P & D Appliance Commercial Parts & Service, Inc. S. San Francisco COLORADO Hawkins Commercial Appliance Englewood FLORIDA Whaley Foodservice Repair Jacksonville Nass Service Co., Inc. Orlando B.G.S.I. Pompano Beach Comm. Appliance Service Tampa GEORGIA TWC Services Smyrna Heritage Service Group Norcross Southeastern Rest. Svc. Norcross HAWAII Burney s Comm. Service, Inc. Honolulu Food Equip Parts & Service Honolulu ILLINOIS Parts Town Lombard Eichenauer Elec. Service Decatur Midwest Elec. Appl. Service Elmhurst Cone s Repair Service Moline INDIANA GCS Service Indianapolis IOWA Electric Motor Service Co. Davenport Goodwin Tucker Group Des Moines KENTUCKY Certified Service Center Lexington Certified Service Center Louisville LOUISIANA Chandlers Parts & Service Baton Rouge MARYLAND Electric Motor Service Baltimore GCS Service Silver Spring MASSACHUSETTS Ace Service Co., Inc. Needham MICHIGAN Commercial Kitchen Service Bay City Bildons Appliance Service Detroit Midwest Food Equip. Service Grandville MINNESOTA GCS Service Minneapolis MISSOURI General Parts Kansas City Commercial Kitchen Services St. Louis Kaemmerlen Parts & Service St. Louis NEBRASKA Anderson Electric Omaha NEVADA Burney s Commercial Las Vegas Hi. Tech Commercial Service N. Las Vegas NEW JERSEY Jay Hill Repair Fairfield Service Plus Flanders NEW YORK Acme American Repairs, Inc. Brooklyn Alpro Service Co. Brooklyn Appliance Installation Buffalo Northern Parts Dist. Plattsburgh J.B. Brady, Inc. Syracuse NORTH CAROLINA Authorized Appliance Charlotte OHIO Akron/Canton Comm. Svc. Inc. Akron Certified Service Center Cincinnati Commercial Parts and Service Columbus Electrical Appl. Repair Service Independence E. A. Wichman Co. Toledo OKLAHOMA Hagar Rest. Service, Inc. Oklahoma City Krueger, Inc. Oklahoma City OREGON Ron s Service, Inc. Portland PENNSYLVANIA Elmer Schultz Services Philadelphia FAST Comm. Appl. Service Philadelphia Appliance Installation & Service Pittsburgh K & D Service Co. Harrisburg Electric Repair Co. Reading RHODE ISLAND Marshall Electric Co. Providence SOUTH CAROLINA Whaley Foodservice Repair W. Columbia TENNESSEE Camp Electric Memphis TEXAS GCS Service Fort Worth Armstrong Repair Service Houston Commercial Kitchen Repair Co. San Antonio UTAH La Monica s Rest. Equip. Service Murray VIRGINIA Daubers Norfolk Daubers Springfield WASHINGTON Restaurant Appl. Service Seattle WISCONSIN A.S.C., Inc. Madison A.S.C., Inc. Milwaukee CANADA ALBERTA Key Food Equipment Service Edmonton BRITISH COLUMBIA Key Food Equipment Service Vancouver MANITOBA Air Rite, Inc. Winnepeg NEW BRUNSWICK EMR Services, Ltd. Moncton ONTARIO R.G. Henderson Ltd. Toronto Choquette CKS Ottawa QUÉBEC Choquette CKS Montreal Choquette CKS Québec City HATCO CORPORATION P.O. Box , Milwaukee, WI U.S.A. (800) (414) Parts & Service Fax (800) Int l. Fax (414) Printed in U.S.A. June 2007 Part No Form No. GRSSRDLM-0607