Instruction Manual, Toftejorg Rotary Spray Heads Toftejorg MultiMidget, Toftejorg MultiMagnum

Transcription

1 Instruction Manual, Toftejorg Rotary Spray Heads Covering Standard version ESE02746EN Date of issue: April 29, 2014 First published: April 29, 2014 Original manual

2

3 Contents Contents... 1 Toftejorg Rotary Spray Heads, Product Program... 3 Toftejorg MultiMidget, Clip-on... 4 Toftejorg MultiMidget, Weld-on... 4 Toftejorg MultiMidget, Thread... 4 Toftejorg MultiMagnum, Weld-on... 5 Toftejorg MultiMagnum, Thread... 5 Introduction... 6 Intended Use... 6 Patents and Trademarks... 7 Quality System... 7 General Description... 8 Functioning... 8 Spray Pattern... 8 Technical Data... 9 Toftejorg MultiMidget... 9 Standard Configurations... 9 Performance Data Toftejorg MultiMagnum Standard Configurations Performance Data Installation and Normal Operation General Installation Instructions General Safety Precautions Normal Operation Service Recommended Service Intervals Claim Procedure How to Contact Alfa Laval Tank Equipment EC Declaration of Conformity Instruction Manual, Toftejorg Rotary Spray Heads Page 1

4

5 Toftejorg Rotary Spray Heads, Product Program This manual covers the product programme for Toftejorg MultiMidget and Toftejorg MultiMagnum. For the different types of Rotary Spray Heads available from Alfa Laval please see: Page 5 for Toftejorg MultiMidget Page 5 for Toftejorg MultiMagnum Alfa Laval Corporate AB This document and its contents is owned by Alfa Laval Corporate AB and protected by laws governing intellectual property and thereto related rights. It is the responsibility of the user of this document to comply with all applicable intellectual property laws. Without limiting any rights related to this document, no part of this document may be copied, reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), or for any purpose, without the expressed permission of Alfa Laval Corporate AB. Alfa Laval Corporate AB will enforce its rights related to this document to the fullest extent of the law, including the seeking of criminal prosecution. Instruction Manual, Toftejorg Rotary Spray Heads Page 3

6 Toftejorg Rotary Spray Heads, Product Program Toftejorg MultiMidget, Clip-on Surface finish: Semi bright Clip-on OD25, 1 ISO2037 Spray pattern Stainless steel Stainless steel Stainless steel 360 TE10M Down 270 Up TE10B up low flow Toftejorg MultiMidget, Weld-on Surface finish: Semi bright Spray pattern Weld-on OD25, 1 ISO2037 Weld-on DN25, DIN R2 Height (mm) Stainless steel Stainless steel Stainless steel Stainless steel TE10M200 TE10M Down 500 TE10M220 TE10M Up 500 TE10M230 TE10M231 Toftejorg MultiMidget, Thread Surface finish: Semi bright Thread-on ½ BSP Thread-on ½ NPT Thread-on ½ BSP Spray pattern Stainless steel Stainless steel Stainless steel Stainless steel Thread-on ½ NPT 360 TE10M000 TE10M002 TE10M001 TE10M Down TE10M020 TE10M022 TE10M021 TE10M Up TE10M030 TE10M032 TE10M031 TE10M033 Page 4 Instruction Manual, Toftejorg Rotary Spray Heads

7 Toftejorg Rotary Spray Heads, Product Program Toftejorg MultiMagnum, Weld-on Surface finish: Semi Bright Spray pattern Weld-on OD38, 1½ ISO2037 Weld-on DN40, DIN R2 Height (mm) Stainless steel Stainless steel Stainless steel Stainless steel TE11M200 TE11M Down 1000 TE11M220 TE11M Up 1000 TE11M230 TE11M231 Toftejorg MultiMagnum, Thread Surface finish: Semi Bright Thread-on 1 1/4 BSP Thread-on 1 1/4 NPT Spray pattern Stainless steel Stainless steel Stainless steel Stainless steel 360 TE11M000 TE11M Down TE11M020 TE11M Up TE11M030 TE11M032 Instruction Manual, Toftejorg Rotary Spray Heads Page 5

8 Introduction This manual has been prepared as a guide for installing, operating and maintaining your Rotary Spray Head tank cleaning machine. The information in this manual is simple to follow, but should you require further assistance, our Technical Sales Support department and worldwide net of sales offices will be pleased to help you. Please quote the type, article and serial numbers with all of your enquiries; this will help us to help you. Warning: Before installing the machine and setting it into operation carefully read the General Installation Instructions (page 13) and the Safety Precautions (page 14) and take all necessary precautions according to your application and local regulations. Note: The illustrations and specifications contained in this manual were effective at the date of printing. However, as continuous improvements are our policy, we reserve the right to alter or modify any unit specification on any product without prior notice or any obligation. Alfa Laval Corporate AB This document and its contents is owned by Alfa Laval Corporate AB and protected by laws governing intellectual property and thereto related rights. It is the responsibility of the user of this document to comply with all applicable intellectual property laws. Without limiting any rights related to this document, no part of this document may be copied, reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), or for any purpose, without the expressed permission of Alfa Laval Corporate AB. Alfa Laval Corporate AB will enforce its rights related to this document to the fullest extent of the law, including the seeking of criminal prosecution. Intended Use It is to be verified by the end-user: - that the tank cleaning machine is in conformity with respect to tank, vessel or container size in which it will be used. - that the construction materials (both metallic and non-metallic) are compatibility with product, flushing media, cleaning media, temperatures and pressure under the intended use. Important information: Liquid inlet pressure: Max. 3 bar. Do not steam. Steaming through the Rotary Spray Head may result in excessive high rotation speed of the cleaner and cause severe wear of the ball bearing and/or damage to the cleaner. See General Installation Instructions on page 13 of this manual for information on recommended installation position. Page 6 Instruction Manual, Toftejorg Rotary Spray Heads

9 Patents and Trademarks This Instruction Manual is published by Alfa Laval Kolding A/S without any warranty. Improvements and changes to this Instruction Manual may at any time be made by Alfa Laval Kolding A/S without prior notice. Such changes will, however, be incorporated in new editions of this Instruction Manual. Alfa Laval Kolding A/S. All rights reserved. The Alfa Laval logotype is a trademark or a registered trademark of Alfa Laval Corporate AB. Toftejorg is a trademark or registered trademark of Alfa Laval Kolding A/S. Other products or company names mentioned herein may be the trademarks of their respective owners. Any rights not expressly granted herein are reserved. Quality System The Toftejorg Rotary Spray Head is produced according to Alfa Laval Kolding s ISO 9001 international Standard certified quality system. All parts are made from certified material. Instruction Manual, Toftejorg Rotary Spray Heads Page 7

10 General Description The Toftejorg Rotary Spray Heads are tank cleaning machines intended for industrial use in tanks, vessels and containers under typical CIP procedures. They have a broad range of application areas within food and chemical industries. The Toftejorg Rotary Spray Head is a sanitary cleaning device of the rotating fan spray type for permanent installation that provides a cleaning pattern from C. The machine is designed in such a way that it is completely self-cleaning. If Installed according to drawing on page 13, the Toftejorg Rotary Spray Head is self-draining in the shown positions. All product contact surfaces are AISI 316 stainless steel (or better corrosion vice). The cleaning device is lubricated by the cleaning media. No oil, grease or other lubricants are used. The Toftejorg Rotary Spray Head is designed for use in food and dairy processing applications. It may be used in reactors, mixing/processing tanks, spray dryers and other process equipment with a volume from m³ (22-10,998 US gallons) and storage tanks up to 125 m³ (27496 US gallons). For larger volumes, multiple Toftejorg Rotary Spray Heads may be applied. Application assistance and optimal position recommendation is available. For use in explosive hazard zones all types can be used, provided they are installed according to the safety instructions in local regulations. Functioning The flow of the cleaning media causes the head of the Toftejorg Rotary Spray Head to rotate, with fans laying out a swirling pattern throughout the vessel. This generates a vibrating impact and cascading flow that covers all internal surfaces of the tank or reactor. The device s self-cleaning feature is achieved by directing the cleaning media through the rotating bearing track and onto the neck of the elongated head. With its double bale race design the MultiMidget and MultiMagnum can be installed in any angle. Spray Pattern U 180 D Page 8 Instruction Manual, Toftejorg Rotary Spray Heads

11 Technical Data Toftejorg MultiMidget Weight of machine : Thread and clip-on: 0.50 kg On pipe: 0.90 kg Working pressure : 1 3 bar Recommended pressure : 2 bar Max. working temperature : 95 C Max. ambient temperature : 140 C Wetting radius : Max. 3 m Impact cleaning radius : Max. effective 1.4 m Materials: inlet connections : (316) bearing race parts : SAF 2205 (UNS31803) balls : AISI 316 head : (AISI 316L) Lubricant : Self-lubricating with the cleaning fluid Connections : 1/2 or ¾ Rp (BSP) or NPT thread Clip-on: 1 ISO2037 Weld-on: 1 ISO2037 or DN25 DIN R2 Standard Configurations Instruction Manual, Toftejorg Rotary Spray Heads Page 9

12 Technical Data Toftejorg MultiMidget (continued) Performance Data Flow rate Throw length Note: The inlet pressure has been taken immediately before the machine inlet. In order to achieve the performance indicated in the curves, the pressure drop in the supply lines between pump and machine must be taken in consideration. Page 10 Instruction Manual, Toftejorg Rotary Spray Heads

13 Technical Data (continued) Toftejorg MultiMagnum Weight of machine : Thread and clip-on: 0.90 kg On pipe: 2.5 kg Working pressure : 1 3 bar Recommended pressure : 2 bar Max. working temperature : 95 C Max. ambient temperature : 140 C Wetting radius : Max. 3 m Impact cleaning radius : Max. effective 2 m Materials: inlet connections : (316) bearing race parts : SAF 2205 (UNS31803) balls : AISI 316 head : (AISI 316L) Lubricant : Self-lubricating with the cleaning fluid Connections : 1 1/4 BSP or NPT thread weld-on: 1 1/2 ISO2037 or DN40 DIN R2 Standard Configurations Instruction Manual, Toftejorg Rotary Spray Heads Page 11

14 Technical Data (continued) Toftejorg MultiMagnum (continued) Performance Data Flow rate Cleaning radius Note: The inlet pressure has been taken immediately before the machine inlet. In order to achieve the performance indicated in the curves, the pressure drop in the supply lines between pump and machine must be taken in consideration. Page 12 Instruction Manual, Toftejorg Rotary Spray Heads

15 Installation and Normal Operation General Installation Instructions Self draining position Important information: Recommended installation position: The Rotary Spray Head tank cleaning machine should be installed in vertical position (upright or upside down). If the machine is installed horizontally, the life time may be reduced. It is recommended to install a filter with mesh size 250 µm (0.01 ) in the supply line in order to avoid particles, scale etc. from clogging the inside of the Rotary Spray Head. Before installation, all supply lines and valves must be thoroughly flushed to remove remains from welding, grinding dust, scale and other foreign matter. During handling and installation handle the machine with care in order not to damage the fine surface of the machine. Note: The machine shall be installed in accordance with national regulations for safety and other relevant regulations and standards. In EU-countries the complete system must fulfil the EU-Machine Directive and depending of application, the EU-Pressure Equipment Directive and other relevant Directives and shall be CE-marked before it is set into operation. Instruction Manual, Toftejorg Rotary Spray Heads Page 13

16 Installation and Normal Operation (continued) General Safety Precautions The Toftejorg Rotary Spray Head is intended for use inside a tank only, and must not be operated in open air or when the tank is open. Warning: Precautions shall be made to prevent starting of the cleaning operation, while personnel are inside the tank or otherwise can be hit by water jets from the cleaner head. Warning: If the machine is used in potential explosive atmospheres, tapes or joint sealing compounds, which are electrical insulators, must not be used on joints, if this may violate the grounding of the machine to the tank. Resistance between nozzles and tank must not exceed Ω. The intended installation with standard clamp connections will ensure this. In addition, connecting pipe work, must be electrically conductive and earthed to the tank structure. This is essential to avoid the build-up of static electricity on the nozzles and the machine. For further information see CENELEC R Safety of Machinery, guidance and recommendations for the avoidance of hazards due to static electricity. Page 14 Instruction Manual, Toftejorg Rotary Spray Heads

17 Installation and Normal Operation (continued) Normal Operation Cleaning Media Use only media compatible with Stainless Steel AISI 316/316L and SAF Normal detergents, moderate solutions of acids and alkalics are acceptable. Aggressive chemicals, excessive concentrations of chemicals at elevated temperatures, as well as certain solvents hydrochlorides should be avoided. If you are in doubt, contact your local Alfa Laval sales office. Pressure Please make sure that the connections are correctly mounted before opening of the washing valve. Put on pressure gradually in order to avoid hydraulic shocks, which might stress mechanical parts in the Toftejorg Rotary Spray Head cleaner. Max. pressure difference is 3.0 bar. Recommendation: After-Use Cleaning After use flush the machine with fresh water. Cleaning media should never be allowed to dry up in the system. Warning: Hot chemicals and steam under pressure may be used for cleaning and sterilising. Protect against scalding and burning. Never tamper with or try to open clamps or other connections while system is in operation. Make sure that system is de-pressurised and drained before disassembly. Instruction Manual, Toftejorg Rotary Spray Heads Page 15

18 Service In case of extensive machine wear, the machine is to be replaced, as it is not possible to repair Rotary Spray Head machines. Recommended Service Intervals Inspection every 500 working hours. After 2000 working hours: inspection every 200 hours. A service consists of: 0. At a pressure of 0.3 bar open a hatch in the tank to verify rotation and liquid fans are emerging from all slots. ATTENTION: Use only pure water at normal temperature for safety reasons. If needed proceed to 1). 1. Un-install the machine 2. Visual inspection for foreign objects. Remove any objects and clean before rotation verification. 3. Rotation verification by hand for free rotation. 4. Reinstall machine 5. Fill in the Service Log Page 16 Instruction Manual, Toftejorg Rotary Spray Heads

19 Claim Procedure In case of failure that needs assistance from your local Alfa Laval sales office, it is essential for our evaluation that the problem, as well as the working conditions of the machine, is described as detailed as possible. How to Contact Alfa Laval Tank Equipment For further information please feel free to contact: Alfa Laval Tank Equipment Alfa Laval Kolding A/S 31, Albuen - DK 6000 Kolding - Denmark Registration number: Tel switchboard: Fax switchboard: info.dk@alfalaval.com Contact details for all countries are continually updated on our websites. Instruction Manual, Toftejorg Rotary Spray Heads Page 17

20 EC Declaration of Conformity Instruction Manual, Toftejorg Rotary Spray Heads Page 18

21 How to contact Alfa Laval Contact details for all countries are continually updated on our website. Please visit to access the information directly. Alfa Laval Corporate AB This document and its contents is owned by Alfa Laval Corporate AB and protected by laws governing intellectual property and thereto related rights. It is the responsibility of the user of this document to comply with all applicable intellectual property laws. Without limiting any rights related to this document, no part of this document may be copied, reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), or for any purpose, without the expressed permission of Alfa Laval Corporate AB. Alfa Laval Corporate AB will enforce its rights related to this document to the fullest extent of the law, including the seeking of criminal prosecution.