TRITON 800 PE TRITON 1000 PE POSEIDON 1100 PE POSEIDON 1200 PE PLUS

Transcription

1 TRITON 800 PE TRITON 1000 PE POSEIDON 1100 PE POSEIDON 1200 PE PLUS DA EN FR DE NL Instruktionsbog Instruction Manual Manuel d instructions Betriebsanleitung Gebruikershandleiding

2 Contents EN Symbols Important safety notes 2 Description 3 Before starting the pressure washer 4 Operation and use 5 Applications and methods 6 After using the pressure washer 7 Maintenance 8 Troubleshooting 9 Further information Intended use Operating elements Transport Setting up the pressure washer Connections Start the pressure washer Pressure regulation Using detergents General information Some typical cleaning tasks Switching off the pressure washer Disconnecting supply lines Storing accessories Storing the cleaner (frost-free) Maintenance plan Maintenance work Recycling the pressure washer Guarantee Technical data Declaration of Conformity

3 Symbols WARNING! Safety instructions in this operating manual which must be observed to prevent risks to persons are marked with this danger symbol. IMPORTANT! This symbol indicates safety instructions that must be observed to prevent damage to the machine or its performance. NOTE! This symbol indicates advice or instructions that make work simpler and ensure safe ope- ration. 26

4 1 Important safety notes EN Before using the high-pressure washer, be sure to also read the enclosed operating instructions and keep them within reach at all times. The high-pressure washer may only be used by persons instructed in its use and who have been expressly authorised to do so. General Use of the high-pressure washer is subject to the applicable local regulations. In addition to the operating instructions and the binding accident prevention regulations in the country of use, the generally recognised rules for safe working must also be observed. Any method of use endangering the safety of persons or equipment is forbidden. Before use Before use, check that the highpressure cleaner is in a safe and proper condition. Operate the pressure washer only in an upright position! Important notes: Do not connect the pressure washer directly to the public drinking water mains (observe DIN 1988 and EN 1717). A connection is permitted, however: briefl y to a pipe interrupter with moving section with a free outlet Water may also be drawn from an open container or from a well or surface water not intended for the drinking water supply. Please use suction set for this. Ensure that neither dirty water nor liquids containing solvents are sucked in. Please observe the regulations and provisions applicable in your country. Before putting the high-pressure washer into service, carry out a visual check of all the major components. High-pressure jets can be dangerous if misused. The jet must not be directed at persons, animals, live electrical equipment or the pressure washer itself. During operation of the washer, recoil forces are produced at the spray lance and, when the lance is held at an angle, a torque is also created. The lance must therefore be held fi rmly in both hands. Risk of injury! Do not direct the jet towards yourself or towards other persons in order to clean clothes or footwear. Do not use the washer when other people without protective clothing are in the working area. Check that cleaning will not result in dangerous substances (e.g. asbestos, oil) being washed off the object to be cleaned and harming the environment. Do not clean delicate parts made of rubber, fabric, etc. with the round jet. Hold the nozzle at a distance of at least 15 cm when cleaning with the highpressure fl at jet. Although extremely easy to operate, children should not be allowed to use the pressure washer. Do not use the high-pressure hose for lifting loads. Do not continue to use the washer if the quick coupling or highpressure hose is damaged. Never use the machine in areas where there is danger of fi re or explosion. When using the pressure washer, stand at least 1 m from buildings, etc. Ensure an adequate air circulation. Do not cover the washer or operate it in inadequately ventilated rooms! The exhaust fumes are dangerous! Store the pressure washer where it will not be exposed to frost! Never operate the pressure washer without water. Even brief shortages of water result in severe damage to the pump seals. Maintenace and repair CAUTION! Before cleaning and servicing the high pressure washer, always remove the ignition plug cable fi rst. Carry out only the maintenance operations described in the operating instructions. Use only original Nilfi sk-alto spare parts. Do not make any technical modifi cations to the high pressure washer. 27

5 CAUTION! High pressure hoses, fi ttings and couplings are important for the safety of the washer. Use only high pressure parts approved by the manufacturer! CAUTION! Failure to observe these instructions can endanger your safety. Safety device The high pressure pump is equipped with a safety valve that redirects the by-pass pressure back to the suction side of the pump. The safety device is set and sealed at the factory and must not be adjusted. Please contact the Nilfi sk-alto service department or an authorised specialist work-shop for all other maintenance or repair work! Testing The machine satisfi es IEC/EN standards. The high pressure washer should be examined as needed or at least once a year by a technician to make sure that it is fail-safe. Our service technicians are at your disposal for assistance and advice. 28

6 2 Description EN 2.1 Intended use This high pressure washer has been designed for professional use in - agriculture - transport industry - construction industry etc. Chapter 5 describes the use of the high-pressure washer for various cleaning jobs. Always use the washer as described in these operating instructions. Any other use may damage the washer or the surface to be cleaned or may result in severe injury to persons. 2.2 Operating elements Start/stop switch 2 Lance 3 Holder for lance and high pressure hose 4 Push handle 5 High pressure hose 6 Spray gun 7 Fastening screw 8 Water connection and water inlet fi lter 9 Parking brake 10 High-pressure hose connection 11 Pressure gauge 12 Oil level gauge TRITON TRITON 10 29

7 3 Before starting the pressure washer 3.1 Transport The washer is easy to transport thanks to its large wheels. For safe transportation in and on vehicles we recommend that you use belts and the parking brake to secure the washer so that it cannot slip or fall over. CAUTION! Never lift the washer alone, weight: TRITON 800 PE = 43 kg TRITON 1000 PE = 61 kg POSEIDON 1100 PE = 75 kg POSEIDON 1200 PE PLUS = 92 kg Always ask a second person to help. 3.2 Setting up the pressure washer If you transport the washer and its accessories at or below 0 C, we recommend the use of antifreeze as described in chapter Before using the pressure washer for the fi rst time, check it carefully to detect any faults or damage. 2. In the event of any damage contact your Nilfi sk-alto dealer immediately. 3. Apply the brake. 4. Fold back the push handle and lock it with the fastening screws. MAX 5. On POSEIDON, check whether the oil level is between the minimum and maximum marks. On TRITON, the oil is chekked through the fi lling plug. If necessary, add oil (see chapter 9.3 for type of oil). MIN POSEIDON TRITON 30

8 4 Operation and use EN 4.1 Connections Connecting the lance to the spray gun C A B 1. Pull the blue quick coupling of the spray gun forward and lock it by turning it to the left. 2. Insert the nipple of the lance into the quick coupling and turn the blue quick coupling grip to the right. 3. Pull the lance (or other accessory) forward to check that it is securely attached to the spray gun. NOTE! Always remove any dirt from the nipple before connecting the lanse to the spray gun Connecting the high pressure hose and the water hose 1. Connect the high pressure hose to the high pressure inlet by means of the quick coupling. PO SEI DON NOTE! The maximum permissible working pressure and temperature are printed on the high pressure hose. Use max. 50 m hose. 2. Before connecting the water hose to the washer, rinse the water hose briefl y to prevent sand and other dirt from entering into the washer. TRITON TRITON 3. Use the quick coupling to attach the water hose to the water connection. 4. Open the tap. (continued -->) 31

9 NOTE! See chapter 9.3 for required quantity of water and water pressure. In the case of poor water quality (sand, etc.), we recommend that a fi ne water fi lter is fi tted in the water inlet. We recommend the use of a textile-reinforced water hose with a nominal diameter of min. 3/4" (19 mm) and a length of min. 6 m. The washer should be fi tted with a preliminary water tank if it is used with hot water or high pressure hoses longer than 10 m or permanent pipe installations Fuelling WARNING! Always shut off the engine and let it cool for at least two minutes before fuelling. Avoid spilling petrol. If you do spill petrol when fuelling, do not start the engine before the spilled petrol has evaporated. If the washer is on a trailer, any petrol spills must be wiped up before the machine is started. Never expose the machine to an open fl ame. Smoking is prohibited during fuelling. Also read the operating manual for the petrol engine. Note: Never operate the ma chine in a closed room; the exhaust fumes are danger ous. Follow the safety instructions in chapter 1! 4.2 Start the washer Switching on the washer when it is connected to a water supply 1. Start the engine. (See the operating manual for the petrol engine.) 2. Unlock the spray gun and operate it. 3. Lock the safety catch even during short pauses. 32

10 4.2.2 Switching on the washer when it is connected to open tanks (suction mode) NOTE! Operate the spray gun several times at short intervals to vent the system. 1. Before connecting the suction hose to the washer, fi ll the hose with water. 2. Start the washer. 3. Unlock the spray gun and operate it. 4. When using this machine in suction mode, fi rst ensure that the system has been bled of air by operating on low pressure until all air has been removed, see chapter 4.3, Pressure regulation. During work breaks of more than three minutes, switch off the washer. EN POSEIDON: Max. suction height: 3m Max. temp.: 70 C TRITON: Max. suction height: 2m Max. temp.: 60 C NOTE! For automatic suction from a tank, watercourse or similar sup ply, the inlet hose must be fi lled with water before you start. The suction height depends on the water temperature. Max. suction height of 3/2 m is reached with cold water (up to 8 C). With 70 C/60 C warm water, the ma chine must be under or at the water level. If the water being suctioned contains particles, a suction fi lter must be mounted on the end of the hose. In case of risk of running sands, a sand fi lter must be attached. 33

11 4.3 Pressure regulation 1. Turn the twist grip on the spray lance: clockwise (+) for high pressure anticlockwise ( ) for low pressure. 4.4 Using detergents Detergent can be added by means of the detergent injector (on POSEIDON, optional accessory). 1. Dilute detergent according to the manufacturer's instructions. 2. Set the pressure to the lowest setting on the lance. 3. The amount of detergent that is drawn in can be regulated by turning the dosing valve of the injector (On RITON, no adjustment possible). CAUTION! Never allow detergent to dry on the surface to be cleaned as this may cause damage. 34

12 5 Applications and methods EN 5.1 General information Effi cient high pressure cleaning is achieved by following a few guidelines, combined with your own personal experience of specifi c cleaning tasks. Acces- sories and detergents, when correctly chosen, can increase the effi ciency of your pressure washer. Here is some basic information about cleaning Soaking Incrusted or thick layers of dirt can be loosened or softened up by a period of soaking. This is for example an ideal method within agriculture for example, within pig sties. The ideal soaking method can be achieved via use of foam or simple alcaline detergent. Let the product lie on the dirty surfaces for around 30 minutes before pressure washing. The result will be a much quicker highpressure cleaning process Detergent and foam Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct contact with the dirt. Detergents are applied from bottom to top, for example on a car bodywork, in order to avoid super clean areas, where Temperature Detergents are more effective at higher temperatures. Greases, oils and fats can be broken down more easily at higher temperatures also. Proteins the detergent collects in higher concentration and streams downwards. Let the detergent react several minutes before cleaning off. can be cleaned at temperatures of around 60 C. Oils, pollution and grease can be cleaned between 70 and 90 C Mechanical effect In order to break down tough layers of dirt, additional mechanical effect may be required. Special lances and rotary or wash brushes offer this supple- mentary effect that cuts through dirt. Use a brush to cut through e.g. traffi c fi lm High water flow or high pressure High pressure is not always the best solution and high pressure may damage surfaces. The cleaning effect also depends upon water fl ow. Pressure levels of around 100 bar may be suffi cient for vehicle cleaning (in association with hot water). Higher fl ow levels give the possibility to rinse and fl ush away large amounts of dirt easily. 35

13 5.2 Some typical cleaning tasks Agriculture Task Stables Pig Pens, sties Cleaning of walls, fl oors and equipment Disinfection Accessories Foam Injector Foam lance Powerspeed lance Floor Cleaner Powerlift lance Detergents Universal Alkafoam Disinfectant DES 3000 Method 1. Soaking apply foam to all surfaces (bottom to top) and wait for approx 30 minutes. 2. Remove the dirt from surfaces with the high-pressure lance or chosen accessory. Clean from bottom to top on vertical surfaces. 3. To fl ush away large quantities of dirt, change to lowpressure mode and use the higher fl ow to push away the dirt. 4. Use recommended disinfectant products and methods to ensure hygiene. Only apply disinfectants once the dirt has been fully removed. Machinery Tractors, ploughs etc. Standard lance Detergent injector Powerspeed lance Curved lance and underchassis washer Brushes 1. Apply detergent to vehicle or equipment surfaces in order to soften up dirt and grime. Work from bottom to top. 2. Proceed with cleaning using the high-pressure lance. Clean again from bottom to top. Use accessories to clean in diffi cult to reach places. 3. Clean fragile areas such as motors or rubber parts at lower pressure levels to avoid damage Vehicle Task Vehicle bodywork Accessories Standard lance Detergent injector Curved lances and underchassis washer Brushes Detergents Aktive Shampoo Aktive Foam Sapphire Super Plus Aktive Wax Allosil RimTop Method 1. Apply detergent to vehicle or equipment surfaces in order to soften up dirt and grime. Apply from bottom to top. In cases of particularly dirty vehicles, pre-spray with a product such as Allosil in order to remove traces of insects etc, then rinse at low pressure and apply normal car cleaning detergent. Let detergents settle for fi ve minutes before cleaning off. Metallic surfaces can be cleaned using RimTop. 2. Proceed with cleaning using the high-pressure lance. Clean again from bottom to top. Use accessories to clean in diffi cult-to-reach places. Use brushes in order to add a mechanical cleaning effect. Short lances can help for cleaning of motors and wheel arches. Curved lances or the undercarriage washer are also ideal for the cleaning of car underchassis and wheel arches. 3. Clean fragile areas such as motors or rubber parts at lower pressure levels to avoid damage. 4. Apply a liquid wax using the pressure washer in order to protect the bodywork from pollution. 36

14 5.2.3 Building & construction / industry Task General surfaces Metallic equipment Rusted or damages surfaces prior to treatment Accessories Foam injector Standard lance Curved lance Tank cleaner Detergents Intensive J25 Multi Combi Aktive Alkafoam Disinfectant DES 3000 Wet Sandblasting equipment Method 1. Apply thick foam over the surfaces to be cleaned. Apply on dry surface. Apply from top to bottom on vertical surfaces. Let the foam act for up to 30 minutes for the optimal effect. 2. After this time, clean down with the high-pressure lance or relevant accessory. Use high pressure to dislodge large amounts of incrusted dirt or grime. Use lower pressure and high water volume in order to fl ush away loose dirt and rinse surfaces. 3. Apply DES 3000 disinfectant once the surfaces are perfectly clean. Areas covered by amounts of loose dirt, such as animal remains in slaughterhouses, can be removed by using high water fl ow to fl ush away the dirt to evacuation pits or drains. The tank cleaner can be used to clean barrels, vats, mixing tanks etc. Tank cleaners may be hydraulically or electrically powered and give the possibility for automatic cleaning without constant monitoring. 1. Connect the sandblasting equipment to the pressure washer and place the suction tube in the sand. 2. Always wear protective equipment during sandblasting. 3. Spray the surfaces to be treated with the mix of water and sand. Rust, paint etc will be stripped off. 4. Following sandblasting, protect surfaces against rust (metal) or rot (wood). These are merely examples of cleaning tasks that can be solved by a pressure washer in association with accessories and detergents. Each cleaning task is different, so please consult your local dealer or Nilfi sk-alto representative in order to discuss the best solution for your own cleaning problem. CAUTION! Never operate the machine in a closed room; the exhaust fumes are dangerous. 37

15 6 After using the washer 6.1 Stop the pressure washer 1. Stop the petrol engine. 2. Close the tap. 3. Operate the spray gun until the wasser is depressurized. 4. Lock the safety catch. 6.2 Disconnecting supply lines 1. Shut the pet cock. 2. Remove the water hose from the washer. 6.3 Storing accessories 1. Hang the lance and the high pressure hose in their holders. 38

16 6.4 Storing the washer (frost-free) 1. Store the pressure washer in a dry room without danger of frost. IMPORTANT! If the high-pressure washer is stored in a room with temperatures around or below 0 C, anti-freeze should be drawn into the pump beforehand: 1. Remove the water inlet hose from the washer. 2. Remove the lance. 3. Start the washer and stop it again after max. one minute. 4. Connect the suction hose to the water inlet of the washer and place it in a tank containing anti-freeze. 5. Start the washer. 6. Hold the spray gun over the tank containing anti-freeze and operate it to start suction. 7. During suction operate the spray gun two or three times. 8. Lift the suction hose from the tank containing antifreeze and operate the spray gun to pump off the remaining anti-freeze. 9. Stop the washer. 10. To avoid any risks, store the poser washer temporarily in a heated room before using it again. 39

17 7 Maintenance 7.1 Maintenance plan 7.2 Maintenance work weekly every six months or 500 operating hours as required Clean water fi lter Clean high pressure nozzle Check oil level Change oil Clean water filter A water fi lter is fi tted on the water inlet to prevent large particles of dirt from entering into the pump. 1. Unscrew the quick coupling. 2. Remove the fi lter and rinse it. Replace damaged fi lter. 3. Tighten the quick coupling gently, so as to avoid damaging the gasket Clean high pressure nozzle A blocked nozzle causes excessive pump pressure. It must therefore be cleaned immediately. 1. Stop the washer. 2. Remove the lance. 3. Clean the nozzle with the Nilfi sk-alto cleaning needle. WARNING! Use the cleaning needle only when the spray lance has been removed. 4. Rinse the lance with water from the nozzle side. 40

18 NOTE! The petrol engine stops automatically if the oil level is low. You can start the petrol engine again once you have added oil Checking the oil level, on POSEIDON 1. Check whether the oil level is between the minimum and maximum levels. Add oil if necessary (see chapter 9.3 for type of oil). MAX MIN Changing the oil, on POSEIDON B 0,5l C C C C A D 1. Before changing the oil, allow the pressure washer to become warm. 2. Loosen the hose clamp (A). 3. Remove the hose from the hose nipple (B). 4. Detach the check pipe (C) from the holder. 5. Allow the oil to drain into a suitable container (min. 1 l capacity) and dispose of oil in compliance with regulations. 6. Hang the check pipe (C) in its holder again. 7. Unscrew the hose nipple (D). 8. Fill pump with fresh oil (see 9.3 for oil type and quantity). 9. Check the oil level (see 7.2.3). 10. Screw in the hose nipple, attach the hose and secure it using the hose clamp. 41

19 7.2.5 Checking the oil level, on TRITON 1-5 mm Quick method: 1. Check whether the oil level is mm under the fi lling orifi ce. This is easily done by marking a thin screwdriver or similar object 65 mm from its end and carefully inserting it in the orifi ce at an angle point ing away from the engine. 2. There should be oil on the lowest 1-5 mm of the screwdriv er. Alternative method: 1. Loosen the fi lling plug and screw it off. 2. Place a half-litre container under the pump. 3. Loosen the drain plug and screw it off. 4. Allow the oil to drain. 5. Measure the volume of oil, and check that it is correct (see chapter 9.3). 6. Screw the drain plug back on, and pour the oil back into the pump. 7. Screw the fi lling plug back on Changing the oil, on TRITON 1. Let the machine reach operating temperature before chang ing the oil. 2. Loosen the fi lling plug and screw it off. 3. Place a half-litre container under the pump. 4. Loosen the drain plug and screw it off. 5. Drain the oil, and dispose of it in the manner prescribed by the authorities. 6. Screw the drain plug back on. 7. Refi ll with new oil (for oil type and quantity, see 9.3). 8. Check oil level, if necessary, using the quick method. 9. Screw the fi lling plug back on. 42

20 8 Troubleshooting EN Fault Cause Remedy Pressure drop Pressure fluctuations In suction mode Excess pressure The motor does not start > Air in the system > High-pressure nozzle blocked/worn > Pressure control on the lanse is not set correctly > Engine speed too low > Pump draws in air (only possible in suction mode) > Lack of water > Pump/accessories partially frozen > Water inlet hose is too long or its cross-section too small > Lack of water caused by blocked water fi lter > Lack of water because max. permissible suction height has not been heeded > Water too hot > Engine s throttle control is defective > Low fuel level > Low oil level in petrol engine > The pump is blocked or frozen Vent the system by operating the spray gun several times at short intervals. If necessary, operate the washer for a short time without the high-pressure hose connected. Clean/replace the high-pressure nozzle. Set the required working pressure. Contact Nilfi sk-alto Service Department. Check that the suction set is air-tight. Repeat aeration. Open the tap. Thaw machine and accessories. Use specifi ed water inlet hose. Clean the water fi lter in the water connection (never work without water fi lter!) See chapter See chapter Give less gas/contact Nilfi sk- ALTO Service Department. Fill with petrol. Fill with oil. Thaw machine/contact Nilfi sk-alto Service Department. 43

21 Fault Cause Remedy The motor stops > Low oil level in petrol engine Fill with oil. When a detergent injector (optional accessory on POSEIDON, standard on TRI TON) is used, detergent is not supplied > Injector is dirty or suction hose is blocked > Detergent tank is empty > The twist grip on the lanse is not set to low pressure Clean. Fill the detergent tank. Turn the twist grip on the lance anti-clockwise as far as possible. 44

22 9 Further information EN 9.1 Recycling the pressure washer If the pressure washer is discarded, make it unusable immediately 1. Dismount the ignition plug. The pressure washer contains valuable materials that should be recycled. Contact your local waste disposal site. If you have any queries, please contact your local authorities or your nearest dealer. 9.2 Guarantee Your Nilfi sk-alto product is guaranteed for 12 months from date of purchase (purchase receipt must be presented) on the following conditions: that defects are attributable to fl aws or defects in materials or workmanship. (Usual wear and tear as well as misuse are not covered by the guarantee). that repairs have not been carried out or attempted by other than Nilfi sk-altotrained service staff. that only original accessories have been applied. that the product has not been exposed to abuse such as knocks, bumps or frost. that the instructions in the manual have been carefully observed. A warranty repair comprises the replacement of defective parts, but it does not cover freight and packaging charges. Besides we refer to national Sale of Goods Act. Any illegitimate guarantee repair will be invoiced. (I.e. malfunctions due to causes mentioned in section 7.0 Trouble shooting of the instruction manual). 45

23 9.3 Technical data POSEIDON POSEIDON TRITON TRI TON 1200 PE PLUS *) 1100 PE 1000 PE 800 PE Working pressure bar Water fl ow (max) l/h Water fl ow Q IEC l/h Max. water inlet temperature C Max. inlet pressure bar Dimensions, l x w x h mm 1010x550x x 550 x 830 Weight of pressure washer kg Weight of spray equipment kg Noise level at a distance of 1m, DIN db (A) Repulsion power N Suction height m Oil quantity in the pump l Pump oil type Castrol ALPHASYN - T ISO150 * With hose reel We reserve the right to make alterations 9.4 Declaration of Conformity Declaration of Conformity Nilfisk-ALTO Division of Nilfi sk-advance A/S Industrivej 1 DK-9560 Hadsund Product: High Pressure Washer Type: Description: TRITON 1000 PE TRITON 800 PE POSEIDON 1100 PE POSEIDON 1200 PE PLUS Petrol driven: 5,5 hp, 11 hp and 13 hp The design of the unit corresponds to the following pertinent regulations: Applied harmonised standards: Applied national standards and technical specifications: EC Machine Directive EC Low-voltage Directive EC EMV Directive EN 292-1, EN EN EN , EN DS EN DIN EN /37/EG 73/23/EEG 89/336/EEG Anton Sørensen V.P. Tech. Ops., Europe Hadsund,

24 INTERNET HEADQUARTER DENMARK Nilfi sk-advance Group Sognevej 25 DK-2605 Brøndby Tel.: SUBSIDIARIES AUSTRALIA Nilfi sk-alto 48 Egerton St. P.O. Box 6046 Silverwater, N.S.W Tel.: Fax: AUSTRIA ALTO Österreich GmbH Nilfi sk-advance AG Metzgerstrasse Bergheim/Salzburg Tel.: verkauf@nilfi sk-alto.at Web: sk-alto.at BRASIL Wap do Brasil Ltda. Rua das Palmeiras 350-Bairro Capela Velha Araucária - Paraná Tel.: wap@wapdobrasil.com.br CANADA ALTO Canada 24 Constellation Road Rexdale Ontario M9W 1K1 Tel.: Fax: CZECH REPUBLIC ALTO Ceská Republika s.r.o. Zateckých Praha 4 Tel.: wap_p@mbox.vol.cz DENMARK Nilfi sk-alto Division of Nilfi sk-advance A/S Industrivej Hadsund Tel.: service@nilfi sk-alto.dk Nilfi sk-alto Food division Division of Nilfi sk-advance A/S Blytækkervej Aalborg Tel.: scanio.technology@nilfi sk-alto.dk. FRANCE Nilfi sk-alto ALTO France S.A. Aéroparc 1 19 rue Icare Entzheim Tel.: info@nilfi sk-alto-fr.com GERMANY Nilfi sk-alto Division of Nilfi sk-advance AG Guido-Oberdorfer-Strasse Bellenberg Tel.: info@nilfi sk-alto.de Web: sk-alto.de GREAT BRITAIN Nilfi sk-alto Division of Nilfi sk-advance Ltd. Bowerbank Way Gilwilly Industrial Estate, Penrith Cumbria CA11 9BN Tel.: sales@nilfi sk-alto.co.uk Web: sk-alto.co.uk HUNGARY ALTO Hungary Kft Csengery ut Nagykanizsa Tel.: Fax: MALAYSIA ALTO DEN-SIN malaysia Sdn Bhd SD14, Jalan KIP 11 Taman Perindustrian KIP Sri Damansara Kuala Lumpur Tel.: densin@tm.net.my NETHERLANDS Nilfi sk-alto Onderdeel van Nilfi sk-advance B.V. Camerastraat BB Almere Tel.: info@alto-nl.com NORWAY ALTO Norge AS Bjørnerudveien Oslo Tel.: info@nilfi sk-alto.no Web: sk-alto.no PORTUGAL NIlfi sk-alto División de Nilfi sk-advance S.A. Sintra Business Park Zona Industrial da Abrunheira Edifi cio 1-1 A SINTRA Centro de Atendimiento ao Cliente: SINGAPORE ALTO DEN-SIN Singapore Pte Ltd. No. 17 Link Road Singapore Tel.: densin@singnet.com.sg Web: SPAIN Nilfi sk-alto División de Nilfi sk-advance S.A. Torre D Ara, Planta Mataró (Barcelona) Centro atención Cliente: info@nilfi sk-alto.es SWEDEN ALTO Sverige AB Box 4029 Aminogatan Mölndal Tel.: info@nilfi sk-alto.se Web: sk-alto.se USA ALTO U.S.Inc Swingley Ridge Road Suite 200 Chesterfi eld, Missouri Tel.: info@alto-us.com ALTO U.S. Inc 2100 Highway 265 Springdale, Arkansas Tel.: info@alto-us.com ALTO U.S. Inc 1100 Haskins Road Bowling Green, Ohio Tel.: info@alto-us.com ALTO Cleaning Systems, Inc Nations Ford Rd. Pineville, North Carolina Tel.: info@nilfi sk-advance.us b ( )