Heat Shields. For use with Stovax, Yeoman & Kensal Freestanding Stove Ranges. Instructions for Installation

Transcription

1 Heat s For use with Stovax, Yeoman & Kensal Freestanding Stove Ranges Instructions for Installation For use in G & IE (Great ritain & Republic of Ireland). IMPORTNT These instructions are designed to complement the appliance installation and user guide in order to install a Stovax, Yeoman or Kensal Freestanding Stove. This supplement should be read in conjunction with the supplied manuals to ensure all the correct installation procedures are followed in order to safely operate the appliance with a Heat. ll kits should only be used in conjunction with Twin Wall Flue Pipe and the minimum height connection between the appliance and flue pipe. DO NOT MODIFY THE HET SHIELDS. PM1119 Issue 3 (July 2015)

2 Installation Instructions overing the following models: Riva Vision Small Riva Vision/ Vogue Midi Stockton 3 4 5/ 5 ML 6 7 Heat Kit RVN-SMHSK RVN-MIDHSK 3HSK ST4HSK 5HSK ST6HSK ST7HSK View 3 5/ 5 ML 5T/ 5T ML 8/8 ML/ 8HL Heat Kit VW-3HSK VW-5HSK VW-5THSK VW-8HSK L3 Yeoman L Yeoman Kensal L5/ L5 ML/ L5 HL Exe Exmoor Heat Kit YM-L3-HSK YM-L5-HSK YM-EXE-HSK YM-EXM-HSK 3HSK 5HSK Top flue versions only. Not suitable for oiler, Inset or anopied Stoves. 1. Packing List 1 panel Spacers x 4 panel M6 Nuts x 4 Fixing Screws x 4 1 x Instructions 1 x 2 x s 4 x Fixing screws 4 x Spacers 4 X M6 Nuts Tools Required Ø 5mm Drill M6 Tap 4mm Hex Key Ø 10mm Drill (for use with Vision Outside ir kit only) ll kits should only be used in conjunction with Twin Wall Flue Pipe and minimum height connection between the appliance and flue pipe. 2

3 2. Options & learances Installation Instructions 2 ack Heat only Twin Wall Flue Pipe Full Heat Twin Wall Flue Pipe Side Wall Rear Wall Side Wall Rear Wall ack Heat only Fitting this heat shield allows a reduction in the clearance to combustible material dimensions to the values as listed:- Riva Vision Small Riva Vision/ Vogue Midi Stockton 3 4 5/ 5 ML 6 7 Side ack View Yeoman L Yeoman Kensal 5/ 5 ML/ 5T/ 5T ML Full Heat L3 L5/ L5 ML/ L5 HL Exe Exmoor Side ack Fitting this heat shield allows a reduction in the clearance to combustible material dimensions to the values as listed:- Riva Vision Small Riva Vision/ Vogue Midi Stockton 3 4 5/ 5 ML 6 7 Side ack View 3 View Yeoman L Yeoman Kensal 5/ 5 ML/ 5T/ 5T ML L3 L5/ L5 ML/ L5 HL Exe Exmoor Side ack These Dimensions are measured from the sides and back of the appliance. Ensure the correct clearance to combustible materials is maintained from any connecting flue pipes, as detailed in uilding Regulations pproved Document J. 3

4 Installation Instructions 3. Drilling Template 3.1 Mark out and drill 4 x M6 tap holes on the back of the appliance in the positions shown in Diagrams 4 & 5 using the dimensions below: 3 Stockton/ View/ L/ Yeoman/ Kensal 4 Riva Vision 4 M6 Holes 4 M6 Holes entre Line entre Line D D D Stockton Stockton Stockton 5/ Stockton 5 Midline Stockton Stockton View View 5/ View 5 Midline View 5T/5T Midline Yeoman L Yeoman L5/ L5 Midline/ L5 Highline Yeoman Exe Yeoman Exmoor Riva Vision Small Riva Vision Midi/Vogue Midi Kensal Kensal Remove Dataplate and washer from the rear of the appliance. These must be refitted during the installation of the Heat s. 4

5 Installation Instructions 4. Installation 5 Spacers x 4 panel Washer Dataplate panel Fixing Screws x 4 DO NOT MODIFY THE HET SHIELDS 4a. If an Outside ir kit has been fitted (Vision Small & Midi only) see section 5 before installing the Heat s. Ensure that the Dataplate and washer have been removed from the rear of the appliance. Note: The Dataplate must be fitted to the bottom right of the rear Heat during installation. 4b. s Take care not to scratch the appliance when locating the Heat s. 4b.1 arefully align the fixing slots with the screws securing the rear Heat to the back of the appliance. The top and the bottom left fixing slots must locate behind the rear Heat, see Diagram a.1 lign the rear Heat with the back of the appliance. Loosely secure with the top 2 and bottom left fixing screws and spacers, see Diagram 5. 4a.2 Loosely secure the Dataplate and washer to the bottom right of the rear Heat using the remaining screw and spacer, see Diagram 5. Ensure that the washer is located between the Dataplate and Heat. 4a.3 If side Heat s are to be fitted do not tighten the screws at this point, see Section 4b. Fixing Screw 4a.4 If not fitting side Heat s tighten the fixing screws to finish the installation. Do not over tighten the fixing screws. Ensure the correct clearance to combustible materials is maintained from any connecting flue pipes, as detailed in uilding Regulations pproved Document J. 5

6 Installation Instructions 5. Flue Pipe Installation 7 The bottom right fixing slot must locate between the rear Heat and the Dateplate washer, see Diagram 7. Dataplate 5. Heat s fitted with an Outside ir Kit - Vision Small, Vision Midi & Vogue Midi only If the Heat is to be fitted with an Outside ir Kit, the following steps will need to carried out prior to installing the Heat kit. Fixing Screw Washer 5.1 Knock out the pre-cut hole in the rear Heat, see Diagram 9. 9 Dataplate The front of the shield rests on the side of the appliance. 4b.2 Tighten the fixing screws to secure the Heat s. Do not over tighten the fixing screws. 4b.3 Repeat on the other side. IMPORTNT When installing the flue pipe the lower edge of the Twin Wall flue must overlap the rear Heat by a minimum of 10mm, see Diagram Drill 2 10mm Ø holes in the Outside ir Kit in the positions shown in Diagram 10 to allow for the spacer tubes Twin Wall Flue 10mm Minimum overlap onnector dapter Riva Vision Small Riva Vision Midi/ Vogue Midi When fitting the ensure that the spacer tubes pass through the Outside ir kit, see Diagram Ensure the correct clearance to combustible materials is maintained from any connecting flue pipes, as detailed in uilding Regulations pproved Document J. ppliance Outside ir Kit Heatshield Spacer 6

7 dditional Guidance on learances To be used if there are no specific dimensions given in instructions No Lintel ombustible Material See Note D - Flue Pipe Diameter ombustible Lintel D learance = 3 x D learance = 3 x D Non-ombustible ppliance Lintel ombustible Material See Note 12mm ir Gap ombustible Lintel ombustible Lintel D Lintel Lintel Non-ombustible ppliance ppliance D - Flue Pipe Diameter learance = 3 x D learance = 1.5 x D Minimum Size Note: - register plate above the appliance must be made from 1.5mm thick galvanised steel. - losure Plate above the appliance must be made from non-combustible material. - ll learances from combustible materials to flue pipes must be as stated in uilding Regulations pproved Document J. 7

8 Stovax Ltd, Falcon Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7LF Tel: (01392) Fax: (01392) E & O E