Drying Tumblers Stacked 30 Pound Capacity

Transcription

1 Drying Tumblers Stacked 30 Pound Capacity Models Through Serial No. DTCK Refer to Page 3 for Model Numbers Parts Part No. M411988R6 November 2012

2

3 Table of Contents Title Page Parts Ordering Information... 2 Serial Plate Location... 2 Model Identification... 3 Single Coin Drop... 4 Dual Coin Drop... 6 Cover Plate... 8 Microprocessor Front Panel Assembly - Models Through Serial No. DTCK ZH Front Panel Assembly - Models Starting Serial No. DTCK ZH Through Serial No. DTCK Side Panels Loading Door Lint Drawer Cylinder Drive Shaft - Models Through Serial No. DTCK YF Drive Shaft - Models Starting Serial No. DTCK YF Blower Housing and Fan Motor and Belt Guard Thermostat and Burner Gas Valve - Single Input Gas Valve - Dual Input Models Starting Serial No. DTCK ZA Through Serial No. DTCK Gas Valve - Dual Input Models Through Serial No. DTCK ZA Gas Valve Coils Junction Box or Volt/60 Hertz Junction Box Volt/50 Hertz Junction Box or Volt/60 Hertz Junction Box Volt/50 Hertz Contactor Box Stickers and Labels - Front of Machine Stickers and Labels - Rear of Machine Parts Index Copyright 2012, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. M

4 If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems at (920) for the name and address of the nearest authorized parts distributor. Parts Ordering Information For technical assistance, call either of the numbers listed below: (920) Ripon, Wisconsin Wevelgem, Belgium When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on serial plate(s) as shown. Serial Plate Location NOTICE WARNING Serial Plate WARNING NOTICE TMB2225P_M M411988

5 Model Identification Information in this manual is applicable to these stacked drying tumbler models: JCD32DG JTD32DG SCD32DG STD32DG M

6 Single Coin Drop 25 TMB2226P_M M411988

7 Single Coin Drop REF PART NO. DESCRIPTION COMMENTS NA P Coin Drop Switch NA Control Panel Overlay S models; Top NA Control Panel Overlay S models; Bottom NA Control Panel Overlay J models; Top NA Control Panel Overlay J models; Bottom NA P Lock, Key and Nut Kit RL001; Can be used to replace items 1 and 2 NA P Lock, Key and Nut Kit RL002; Can be used to replace items 1 and Coin Drop Key 2 N/A Lock and Key Assembly J Reject Button 4 N/A Reject Button Spring 5 N/A Reject Button Cover Plate 6 N/A Coin Switch.25 7 N/A Rejector.25 8 N/A Clip 9 N/A Single Wire Harness Assembly P Coin Drop Kit U.S.; N/A Coin Drop Token; STD N/A Coin Drop Canada; N/A Coin Drop Japan; 100 yen Coin Drop France; 2 franc 10 N/A Coin Drop Hong Kong; $5.00 piece 10 N/A Coin Drop Token; STD Coin Drop Korea; 500 won 10 N/A Coin Drop Token; STD N/A = Part no longer available M

8 Dual Coin Drop TMB2227P_M M411988

9 Dual Coin Drop REF PART NO. DESCRIPTION COMMENTS NA Overlay S models; Top NA Overlay S models; Bottom NA Overlay J models; Top NA Overlay J models; Bottom Coin Drop Key 2 N/A Lock and Key Assembly J Reject Button 4 N/A Reject Button Spring 5 N/A Reject Button Cover Plate 6 N/A Switch 7 N/A Rejector.10 8 N/A Coin Switch 9 N/A Rejector N/A Clip 11 N/A Dual Wire Harness Assembly 12 N/A Coin Drop U.S.;.10 and N/A Coin Drop England; 20 pence and 50 pence Coin Drop Australia; Coin Drop Belgium; 5 franc and 20 franc 12 N/A Coin Drop Canada;.25 and 1.00 N/A = Part no longer available M

10 Cover Plate For Manual Start Kit TMB2228P_M M411988

11 Cover Plate REF PART NO. DESCRIPTION COMMENTS NA Nut Models through Serial No. DTCK ZH NA M Nut Models starting Serial No. DTCK ZH 1 N/A Timer Switch Instruction Plate Switch Plate 2 required 3 N/A Washer 2 required 4 N/A Microprocessor Start Assembly N/A = Part no longer available NOTE: DTCK ZH was Serial No. for models with angled Coin Vault located below Coin Drop. Single Coin Drops did not change with Coin Vault change. M

12 COTTONS Microprocessor 1. UPPER DRYER OPERATING INSTRUCTIONS Check inside machine for children, pets, and foreign objects before loading and starting. Load dryer and close door. Insert proper coins. Adding coins before dryer stops adds time. 5. Select temperature setting desired. To dry cottons, select "HIGH TEMP." To dry perm press, select "MED. TEMP." To dry delicates, select "LOW TEMP." 6. Push and release START button. 7. To change temperature, simply select new temperature setting. MED TEMP AVAILABLE DELICATES MORE COINS DRYING COOLING DOOR OPEN TMB2229P_M M411988

13 Microprocessor REF PART NO. DESCRIPTION COMMENTS NA P Lock, Key and Nut Kit RL001; Can be used to replace items 1 and 2 NA P Lock, Key and Nut Kit RL002; Can be used to replace items 1 and Coin Drop Key P Microprocessor Door Lock 3 N/A Gasket 4 N/A Microprocessor Programming Label 5 N/A Pilot Light Models through Serial No. DTCK N/A Microprocessor Display Sticker 7 N/A Flat Lens Models through Serial No. DTCK P Microprocessor Wire Harness Kit 9 N/A Microprocessor Control Assembly 10 N/A Microprocessor Cover Assembly Left 10 N/A Microprocessor Cover Assembly Right Door Graphics Upper door; Models SCD32DG and STD32DG Door Graphics Lower door; Models SCD32DG and STD32DG 11 N/A Microprocessor Overlay Upper; Models JCD32DG and JTD32DG 11 N/A Microprocessor Overlay Lower; Models JCD32DG and JTD32DG N/A = Part no longer available M

14 10 25 OPERATING INSTRUCTIONS 1. Check inside machine for children, pets, and foreign objects before loading and starting. 2. Load dryer and close door. 3. Insert proper coins. 4. Adding coins before dryer stops adds time. 5. Select temperature setting desired. To dry cottons, select "HIGH TEMP." To dry perm press, select "MED. TEMP." To dry delicates, select "LOW TEMP." 6. Push and release START button. 7. To change temperature, simply select new temperature setting. COTTONS MED TEMP DELICATES AVAILABLE MORE COINS DRYING COOLING DOOR OPEN OPERATING INSTRUCTIONS 1. Check inside machine for children, pets, and foreign objects before loading and starting. 2. Load dryer and close door. 3. Insert proper coins. 4. Adding coins before dryer stops adds time. 5. Select temperature setting desired. To dry cottons, select "HIGH TEMP." To dry perm press, select "MED. TEMP." To dry delicates, select "LOW TEMP." 6. Push and release START button. 7. To change temperature, simply select new temperature setting. COTTONS MED TEMP DELICATES AVAILABLE MORE COINS DRYING COOLING DOOR OPEN Front Panel Assembly - Models Through Serial No. DTCK ZH TMB2230P_M M411988

15 Front Panel Assembly - Models Through Serial No. DTCK ZH REF PART NO. DESCRIPTION COMMENTS LP Front Panel Assembly Upper 1 N/A Front Panel Assembly Stainless steel; Upper 2 M Door Latch Included with front panel 3 M Pop Rivet Included with front panel 4 N/A Microprocessor Control Assembly Coin Chute 6 N/A Coin Chute Bracket Left 6 N/A Coin Chute Bracket Right 7 N/A Coin Vault Plug Blind Rivet 9 N/A Coin Vault Gusset 10 N/A Screw 11 N/A Front Panel Assembly Lower 11 N/A Front Panel Assembly Stainless steel; Lower 12 M Shadow Box Clip Coin Vault Shadow Box * Hinge Bracket Included with front panel Hinge Bracket Stainless steel 15 M Pop Rivet Included with front panel P Lint Drawer Seal Included with front panel 17 N/A Microprocessor Control Shadow Box Included with front panel 18 N/A Coin Drop Shadow Box * Add Letter To Designate Color. H - Harvest Gold L - Almond W - White N/A = Part no longer available M

16 1. Check inside machine for children, pets, and foreign objects before loading and starting. 2. Load dryer and close door adds time Push and release START button. To change temperature, simply select new temperature setting. COTTONS MED TEMP DELICATES AVAILABLE MORE COINS DRYING COOLING DOOR OPEN Insert proper coins. 4. adds time Push and release START button. 7. To change temperature, simply select new temperature setting. COTTONS MED TEMP DELICATES AVAILABLE MORE COINS DRYING COOLING DOOR OPEN Front Panel Assembly - Models Starting Serial No. DTCK ZH Through Serial No. DTCK OPERATING INSTRUCTIONS Insert proper coins. Adding coins before dryer stops Select temperature setting desired. To dry cottons, select "HIGH TEMP." To dry perm press, select "MED. TEMP." To dry delicates, select "LOW TEMP." OPERATING INSTRUCTIONS Check inside machine for children, pets, and foreign objects before loading and starting. Load dryer and close door. Adding coins before dryer stops Select temperature setting desired. To dry cottons, select "HIGH TEMP." To dry perm press, select "MED. TEMP." To dry delicates, select "LOW TEMP." TMB2231P_M M411988

17 Front Panel Assembly - Models Starting Serial No. DTCK ZH Through Serial No. DTCK REF PART NO. DESCRIPTION COMMENTS NA * Coin Drawer Assembly Left NA * Coin Drawer Assembly Right NA Safety Wire Harness Assembly Models through Serial No. DTCK N/A Front Panel Assembly Upper 1 N/A Front Panel Assembly Stainless steel; Upper 2 M Door Latch Included with front panel 3 M Pop Rivet Included with front panel 4 N/A Microprocessor Control Assembly Nut 6 required 6 N/A Coin Vault Assembly Left 6 N/A Coin Vault Assembly Right 7 N/A Screw 6 required Coin Vault Shadow Box 9 N/A Front Panel Assembly Lower 9 N/A Front Panel Assembly Stainless steel; Lower 10 N/A Coin Drop Kit U.S.; N/A Coin Drop Token; STD N/A Coin Drop Canada; N/A Coin Drop Japan; 100 yen 10 N/A Coin Drop Hong Kong; $5.00 piece 10 N/A Coin Drop Token; STD Coin Drop Korea; 500 won 10 N/A Coin Drop Token; STD * Hinge Bracket Hinge Bracket Stainless steel; included with front panel 12 M Pop Rivet Included with front panel P Lint Drawer Seal Included with front panel 14 M Shadow Box Clip Included with front panel 15 N/A Microprocessor Control Shadow Box * Add Letter To Designate Color. H - Harvest Gold L - Almond W - White N/A = Part no longer available M

18 Side Panels TMB2232P_M M411988

19 Side Panels REF PART NO. DESCRIPTION COMMENTS 1 M Snap Bushing 2 N/A Cabinet Bracket 3 N/A Insulation 4 N/A Mounting Bracket 5 N/A Right Side Cabinet Assembly Screw 6 N/A Screw 7 N/A Nut Screw 9 M Door Switch Located on front panel on models through Serial No. DTCK ZH Door Switch Bracket 11 M Screw Leveling leg 12 N/A Left Side Cabinet Assembly N/A = Part no longer available M

20 Loading Door TMB2233P_M M411988

21 Loading Door REF PART NO. DESCRIPTION COMMENTS NA Door Handle Models JCD32DG and JTD32DG; Crossbar NA P Replacement Door Handle Kit NA M Screw Models JCD32DG and JTD32DG; For door handle NA M Nut Models JCD32DG and JTD32DG; For door handle NA Q6163 Nut Models JCD32DG and JTD32DG; For door hinge NA Washer Models JCD32DG and JTD32DG; For door hinge NA M Screw Door Assembly Models JCD32DG and JTD32DG; Plain 1 M Door Assembly Models JCD32DG and JTD32DG; Logo Door Assembly Models SCD32DG and STD32DG 2 M Door Ring Gasket Nut Screw 5 N/A Door Switch Tab 6 M Screw 7 M Hinge Pin 8 M Door Latch 9 M Pop Rivet 10 M Door Switch Located on side panel on models starting Serial No. DTCK ZH * Hinge Bracket Painted; Included with front panel Hinge Bracket Stainless steel; Included with front panel 12 M Pop Rivet 13 M402714* Door Hinge Assembly Painted 13 M Hinge Assembly Stainless steel 14 M Washer 15 M400784P Door Glass P Door Glass Models JCD32DG and JTD32DG 16 M Screw Door Handle Models JCD32DG and JTD32DG; Crossbar Door Handle Models JCD32DG and JTD32DG Door Handle Models SCD32DG and STD32DG P Door Glass Seal Kit 19 N/A Door Plug Screw 21 M Screw * Add Letter To Designate Color. H - Harvest Gold L - Almond W - White N/A = Part no longer available M

22 Lint Drawer GRAPHIC PANEL TMB2234P_M M411988

23 Lint Drawer REF PART NO. DESCRIPTION COMMENTS NA Lint Drawer Seal NA P Lock, Key and Nut Kit RL001; Can be used to replace items 1 and 2 NA P Lock, Key and Nut Kit RL002; Can be used to replace items 1 and 2 1 M Panel Key Models SCD32DG and STD32DG Coin Drop Key Models JCD32DG and JTD32DG P Lock and Key Lint Screen Frame Assembly Models through Serial No. DTCK Lint Screen Frame Assembly Models starting Serial No. DTCK Screw 5 N/A Lint Screen Bracket P Lint Drawer Seal Included with front panel Lint Drawer Assembly Models through Serial No. DTCK N/A Lint Drawer Assembly Models starting Serial No. DTCK Screw 9 N/A Lint Drawer Switch 10 N/A Lint Drawer Assembly Models through Serial No. DTCK Switch Models starting Serial No. DTCK N/A Front Plate Upper; Models SCD32DG and STD32DG 12 N/A Front Plate Upper; Models JCD32DG and JTD32DG Lint Compartment Label Kickplate Extension Models starting Serial No. DTCK N/A Front Plate Lower; Models through Serial No. DTCK N/A Front Plate Lower; Models starting Serial No. DTCK Blind Rivet Actuator Switch Block N/A = Part no longer available M

24 Cylinder TMB2235P_M M411988

25 Cylinder REF PART NO. DESCRIPTION COMMENTS NA Adhesive Attaches felt seal to cylinder NA 263P4 Cylinder Guide Tool NA P Cylinder Assembly Trunnion not included NA Lint Drawer Lock Plate P Front Seal Kit Includes strap Spring Rib Assembly P Cylinder and Trunnion Assembly P Seal Strap 6 M Felt Pad Trunnion Assembly Cylinder Bearing Stud Plate Assembly Washer Nut 11 M Nut 12 M Nut 13 M Washer P Support Housing Bearing Assembly 15 M Nut 16 M Washer 17 M Spacer P Seal Kit 19 N/A Sweep Sheet Bumper Kit P Sweep Sheet Kit 21 M Pop Rivet Screw 23 F Nut 4 required Retaining Ring 2 required 25 N/A Washer 2 required Roller Shaft 2 required Roller Shaft Retainer 2 required Roller Bearing Assembly 2 required Nut 2 required Bracket Attaches to roller bracket Spring 32 N/A Cylinder Rib Rod P Front Cylinder Seal Strap N/A = Part no longer available M

26 Drive Shaft - Models Through Serial No. DTCK YF TMB2236P_M M411988

27 Drive Shaft - Models Through Serial No. DTCK YF REF PART NO. DESCRIPTION COMMENTS NA Screw NA Washer Screw Drum Idler Wheel Assembly Screw Nut Cylinder Idler Arm Washer Nut Screw 9 M Washer 10 N/A Flange Bearing Will need to order the following items from the Drive Shaft section: 10, 15-19, 23, 25 and P Sheave Steel; With set screw Belt 13 N/A Flange Bearing and Drive Shaft Will need to order the following items from the Drive Shaft section: 10, 15-19, 23, 25 and Cylinder Idler Bracket 15 M Screw Washer P Belt Poly-V J ; 8 rib; inches P Pulley Kit 19 N/A Drum Idler Spring N/A = Part no longer available M

28 Drive Shaft - Models Starting Serial No. DTCK YF TMB2237P_M M411988

29 Drive Shaft - Models Starting Serial No. DTCK YF REF PART NO. DESCRIPTION COMMENTS Screw Drum Idler Wheel Assembly Screw Nut Cylinder Idler Arm Washer Nut Screw 9 M Washer Nut P Sheave Steel; With set screw 12 M Nut 13 M Nut Belt P U-Bolt Clamp Kit 16 N/A Partition Reinforcing Plate Back Jackshaft Assembly Partition Reinforcing Plate Front 19 M Key P Belt P Pulley Kit 22 N/A Drum Idler Spring 23 M Key Cylinder Idler Bracket 25 M Screw Washer N/A = Part no longer available M

30 Blower Housing and Fan TMB2238P_M M411988

31 Blower Housing and Fan REF PART NO. DESCRIPTION COMMENTS NA Screw 4 required; Attaches bracket to blower housing Fan Shaft Assembly Washer Nut Nut 5 N/A Sheave 6 N/A Top and Front Cover Washer 8 M Limit Thermostat P Thimble and Vane Assembly Vane Assembly 2 required 11 M Bumper 12 M Screw Washer Screw Screw Drum Idler Wheel Assembly Drive Idler Arm 18 N/A Idler Pulley Bracket Nut 20 N/A Spacer Drive Idler Spring 22 N/A Idler Spring Tab Screw 24 M Nut 25 M Nut P Blower 27 N/A Blower Housing Assembly Screw 29 M Sensor Side and Back Cover N/A = Part no longer available M

32 Motor and Belt Guard TMB2239P_M M411988

33 Motor and Belt Guard REF PART NO. DESCRIPTION COMMENTS NA M Vent and Thimble Caution Label NA M Motor Capacitor Belt 2 N/A Sheave 60 Hertz; Includes setscrew 2 N/A Sheave 50 Hertz; Includes setscrew Screw Switch Models starting Serial No. DTCK N/A Belt Guard 6 N/A Belt Guard Switch Models through Serial No. DTCK Washer 8 M Screw 9 M Washer P Motor 60 Hertz Motor 50 Hertz N/A = Part no longer available M

34 Thermostat and Burner TMB2240P_M M411988

35 Thermostat and Burner REF PART NO. DESCRIPTION COMMENTS 1 N/A Top Thermostat Cover Models through Serial No. DTCK N/A Front Thermostat Cover Models through Serial No. DTCK Step Down Thermostat Models through Serial No. DTCK P Reset Thermostat Models through Serial No. DTCK P Close Limit Thermostat Models through Serial No. DTCK Stove Limit Thermostat Models starting Serial No. DTCK M Thermostat Cover Models starting Serial No. DTCK Screw Screw Burner Cover Plate Screw P Spark Igniter 12 N/A Burner Assembly Washer P Airflow Switch Kit Includes items Cotter Pin Airflow Switch Vane 17 M Screw Airflow Switch 19 H Mounting Insulation Nut N/A = Part no longer available M

36 Gas Valve - Single Input Models Starting Serial No. DTCK TMB2241P_M M411988

37 Gas Valve - Single Input REF PART NO. DESCRIPTION COMMENTS NA 563P3 Conversion Kit Natural Gas (N.G.) to Liquid Petroleum Gas (L.P.) NA 550P3 Conversion Kit L.P. to N.G P3 N.G. Valve Replacement Kit N.G.; 60 Hertz 1 N/A Gas Valve Assembly N.G.; 50 Hertz 1 868P3 L.P. Valve Replacement Kit L.P.; 60 Hertz 1 N/A Gas Valve Assembly L.P.; 50 Hertz P Shut-Off Valve Kit Models starting Serial No. DTCK A O-Ring P Shut-Off Valve Kit Models starting Serial No. DTCK N/A Gas Valve Gasket 6 N/A Gas Valve Spud Burner Orifice N.G.; 0-2,000 feet; Drill no Burner Orifice N.G; 2,001-4,000 feet; Drill no Burner Orifice N.G.; 4,001-6,000 feet; Drill no N/A Burner Orifice N.G.; 6,001-8,000 feet; Drill no N/A Burner Orifice N.G.; 8,001-10,000 feet; Drill no Burner Orifice Liquid Natural Gas (L.N.G.); 0-2,000 feet; Drill no N/A Burner Orifice Town Gas (L.P.); 0-2,000 feet; Drill no. V Burner Orifice L.P.; 0-2,000 feet; 3/32 inch 7 N/A Burner Orifice L.P.; 2,001-6,000 feet; Drill no N/A Burner Orifice L.P.; 6,001-8,000 feet; Drill no N/A Burner Orifice L.P.; 8,001-10,000 feet; Drill no High Voltage Lead 9 M Snap Bushing 10 N/A Gas Valve Bracket Screw N/A = Part no longer available M

38 Gas Valve - Dual Input Models Starting Serial No. DTCK ZA Through Serial No. DTCK TMB2242P_M M411988

39 Gas Valve - Dual Input Models Starting Serial No. DTCK ZA Through Serial No. DTCK REF PART NO. DESCRIPTION COMMENTS NA 514P3 Conversion Kit Natural Gas (N.G.) to Liquid Petroleum Gas (L.P.) 1 867P3 N.G. Valve Replacement Kit N.G.; 60 Hertz 1 N/A Gas Valve Assembly N.G.; 50 Hertz 1 868P3 L.P. Valve Replacement Kit L.P.; 60 Hertz 1 N/A Gas Valve Assembly L.P.; 50 Hertz 2 M Nut Union 3 N/A Tailpiece 3/8 male NPT P Shut-Off Valve Kit 5 M Anti-Torque Ring 6 N/A Burner Orifice N.G.; 0-2,000 feet; Drill no N/A Burner Orifice N.G.; 2,001-4,000 feet; 1/8 inch 6 N/A Burner Orifice N.G.; 4,001-6,000 feet; Drill no N/A Burner Orifice N.G.; 6,001-8,000 feet; Drill no N/A Burner Orifice N.G.; 8,001-10,000 feet; Drill no N/A Burner Orifice Liquid Natural Gas (L.N.G.); 0-2,000 feet Burner Orifice L.P.; 0-2,000 feet; Drill no Burner Orifice L.P.; 2,001-4,000 feet; Drill no N/A Burner Orifice L.P.; 4,001-8,000 feet; Drill no N/A Burner Orifice L.P.; 8,001-10,000 feet; Drill no N/A Gas Valve Gasket Burner Orifice N.G.; 2,001-4,000 feet; Drill no N/A Burner Orifice N.G.; 4,001-6,000 feet; Drill no N/A Burner Orifice N.G.; 6,001-8,000 feet; Drill no Burner Orifice N.G.; 8,001-10,000 feet; Drill no N/A Burner Orifice L.N.G.; 0-2,000 feet; Drill no N/A Burner Orifice Town Gas; L.P.; 0-2,000 feet; Drill no. V Burner Orifice L.P.; 0-2,000 feet; 3/32 inch 8 N/A Burner Orifice L.P.; 2,001-6,000 feet; Drill no N/A Burner Orifice L.P.; 6,001-8,000 feet; Drill no N/A Burner Orifice L.P.; 8,001-10,000 feet; Drill no N/A Burner Orifice Town Gas; 0-2,000 feet; Drill no. A 9 N/A Gas Valve Spud High Voltage Lead 11 M Snap Bushing 12 N/A Gas Valve Bracket Screw N/A = Part no longer available M

40 Gas Valve - Dual Input Models Through Serial No. DTCK ZA TMB2242P_M M411988

41 Gas Valve - Dual Input Models Through Serial No. DTCK ZA REF PART NO. DESCRIPTION COMMENTS NA 474P3 Conversion Kit Natural Gas (N.G.) to Liquid Petroleum Gas (L.P.) 1 867P3 N.G. Valve Replacement Kit N.G.; 60 Hertz 1 N/A Gas Valve Assembly N.G.; 50 Hertz 1 868P3 L.P. Valve Replacement Kit L.P.; 60 Hertz 1 N/A Gas Valve Assembly L.P.; 50 Hertz 2 M Nut Union 3 N/A Tailpiece 3/8 male NPT P Shut-Off Valve Kit 5 M Anti-Torque Ring 6 N/A Burner Orifice N.G.; 0-2,000 feet; 1/8 inch 6 N/A Burner Orifice N.G.; 2,001-4,000 feet; Drill no N/A Burner Orifice N.G.; 4,001-6,000 feet; Drill no N/A Burner Orifice N.G.; 6,001-8,000 feet; Drill no N/A Burner Orifice N.G.; 8,001-10,000 feet; Drill no Burner Orifice L.P.; 0-2,000 feet; Drill no N/A Burner Orifice L.P.; 2,001-4,000 feet; Drill no N/A Burner Orifice L.P.; 4,001-6,000 feet; Drill no N/A Burner Orifice L.P.; 6,001-8,000 feet; Drill no N/A Burner Orifice L.P.; 8,001-10,000 feet; Drill no N/A Gas Valve Spud Burner Orifice N.G.; 0-2,000 feet; Drill no N/A Burner Orifice N.G.; 2,001-4,000 feet; Drill no N/A Burner Orifice N.G.; 4,001-6,000 feet; Drill no Burner Orifice N.G.; 6,001-8,000 feet; Drill no N/A Burner Orifice N.G.; 8,001-10,000 feet; Drill no Burner Orifice L.P.; 0-2,000 feet; Drill no N/A Burner Orifice L.P.; 2,001-4,000 feet; Drill no N/A Burner Orifice L.P.; 4,001-6,000 feet; Drill no N/A Burner Orifice L.P.; 6,001-8,000 feet; Drill no N/A Burner Orifice L.P.; 8,001-10,000 feet; Drill no N/A Gas Valve Gasket High Voltage Lead 11 M Snap Bushing 12 N/A Gas Valve Bracket Screw N/A = Part no longer available M

42 Gas Valve Coils BLK WHT BLK BLK WHT WHT BLK BLK BLK WHT RED/BLK WHT RED WHT BLUE/BLK RED TMB2243P_M M411988

43 Gas Valve Coils REF PART NO. DESCRIPTION COMMENTS 1 M409253P Instant Electronic Ignition Valve Coil Kit Model starting Serial No. DTCK Coil and Harness Kit 60 Hertz; Models through Serial No. DTCK N/A Coil and Harness Kit 50 Hertz; Models through Serial No. DTCK N/A = Part no longer available M

44 Junction Box or Volt/60 Hertz Models Through Serial No. DTCK TMB2244P_M M411988

45 Junction Box or Volt/60 Hertz REF PART NO. DESCRIPTION COMMENTS NA Instant Electronic Ignition Wire Harness Assembly Models through Serial No. DTCK or DTCK NA P Main Wire Harness Assembly Volt/60 Hertz; Lower NA P Main Harness Assembly 120 Volt/50 or 60 Hertz; Upper; Models starting Serial No. DTCK ZH through DTCK P Fuse Receptacle 2 M Fuse 6 Amp; 250 Volt 3 M Snap Bushing 4 N/A Latch Relay 5 N/A Jumper Terminal Block Terminal Block 120 Volt Terminal Block 240 Volt Screw Junction Box Cover 9 M406789P Ignition Control N/A = Part no longer available M

46 Junction Box Volt/50 Hertz Models Through Serial No. DTCK TMB2244P_M M411988

47 Junction Box Volt/50 Hertz REF PART NO. DESCRIPTION COMMENTS NA Instant Electronic Ignition Wire Harness Assembly NA Relay Isolation; 240 Volt P Fuse Receptacle 2 M Fuse 6 Amp; 250 Volt 3 M Snap Bushing 4 N/A Latch Relay 5 N/A Jumper Terminal Block Terminal Block 120 Volt Screw Junction Box Cover 9 M406789P Ignition Control N/A = Part no longer available Models through Serial No. DTCK or DTCK M

48 Junction Box or Volt/60 Hertz Models Starting Serial No. DTCK TMB2245P_M M411988

49 Junction Box or Volt/60 Hertz REF PART NO. DESCRIPTION COMMENTS NA Instant Electronic Ignition Wire Harness Assembly Models through Serial No. DTCK or DTCK P Fuse Receptacle Located in upper junction box only 2 M Fuse 6 Amp; 250 Volt; Located in upper junction box only 3 M Snap Bushing 4 N/A Jumper Terminal Block Terminal Block 120 Volt Terminal Block 240 Volt Screw Junction Box Cover 8 M406789P Ignition Control N/A = Part no longer available M

50 Junction Box Volt/50 Hertz Models Starting Serial No. DTCK TMB2245P_M M411988

51 Junction Box Volt/50 Hertz REF PART NO. DESCRIPTION COMMENTS NA Instant Electronic Ignition Wire Harness Assembly Models through Serial No. DTCK or DTCK NA Relay Isolation; 240 Volt P Fuse Receptacle Located in upper junction box only Fuse 3/4 Amp; 250 Volt; Located in upper junction box only 3 M Snap Bushing 4 N/A Jumper Terminal Block Terminal Block 120 Volt Screw Junction Box Cover 8 M406789P Ignition Control N/A = Part no longer available M

52 5 Contactor Box CE Models 230 Volt/50 Hertz/1 Phase T1 T2 T3 NO 14 L1 L2 L3 13 NO T TMB2246P_M M411988

53 Contactor Box REF PART NO. DESCRIPTION COMMENTS NA M Nut NA Fuse.4 Amp NA M End Barrier 1 M Finger Guard Upper unit only 2 M412187P Mounting Switch Base Upper unit only; Disconnect 3 M Terminal Block 1 circuit 4 M Terminal Block End Stop 230 Volt 6 M Ground Buss Assembly 7 M412477P Transformer 230 Volt Screw 9 M Snap Bushing 10 M Din Rail 88.9 mm 11 M Terminal Block 2 circuit 12 N/A Modified Extension 13 N/A Din Rail 127 mm P Contactor Motor; 9 Amp N/A = Part no longer available M

54 Stickers and Labels - Front of Machine UPPER DRYER LOWER DRYER TMB2247P_M M411988

55 Stickers and Labels - Front of Machine REF PART NO. DESCRIPTION COMMENTS 1 M Warning Label Located on front panel behind door 2 N/A Microprocessor Display Sticker Located on back of micro door 3 N/A Microprocessor Programming Label Located on back of micro door Warning Label Located under lint drawer N/A = Part no longer available M

56 Never operate the war with the front panel bfb Never operate the washer with the front panel removed Never aa the washer with the front panel removed This unit requires a SINGLE power source. Make electrical connections through top junction box. Remove junction box cover to make electrical connections. Replace junction box cover after making electrical connections. Stickers and Labels - Rear of Machine Serial Plate Gas Supply Pipe Tag NOTICE Operate the washer Never operate the war with the front panel bfb removed. Never operate the washer with the front panel removed Never aathe washer with the front panel removed WARNING AVERTISSEMENT NOTICE Never operate the front panel Never operate with the front Never aathe the front panel WARNING AVERTISSEMENT NOTICE WARNING NOTICE Operate the washer NOTICE Never operate the front panel Never operate with the front Never aathe the front panel Never operate the war with the front panel bfb removed. Never operate the washer with the front panel removed Never aathe washer with the front panel removed WARNING AVERTISSEMENT Gas Supply Pipe Tag WARNING AVERTISSEMENT NOTICE WARNING Wiring diagrams (Refer to Serial No./Wiring Tables) TMB2248P_M M411988

57 Stickers and Labels - Rear of Machine REF PART NO. DESCRIPTION COMMENTS 1 N/A Installation Notice Sticker Warning Label Dual language 3 N/A Junction Box Notice Sticker 4 M Secure Ground Label 5 N/A Wire Marker 6 N/A Power Source Notice Sticker 7 N/A Belt Warning Sticker 8 M Vent and Thimble Caution Label 9 N/A Thimble Notice Label N/A = Part no longer available M

58 Notes 56 M411988

59 Parts Index A Actuator Switch Block Adhesive Airflow Switch Airflow Switch Kit P Airflow Switch Vane Anti-Torque Ring M , 39 B Belt , 27, P... 25, 27 Blind Rivet , 21 Blower P Bracket Bumper M Burner Cover Plate Burner Orifice , , , C Close Limit Thermostat P Coil and Harness Kit Coin Chute Coin Drawer Assembly * * Coin Drop , Coin Drop Key , 7, 11, 21 Coin Drop Kit P...5 Coin Drop Switch P...5 Coin Vault Shadow Box , 15 Contactor P...51 Control Panel Overlay Conversion Kit 474P P P P Cotter Pin Cylinder and Trunnion Assembly P...23 Cylinder Assembly P...23 Cylinder Bearing Stud Plate Assembly Cylinder Guide Tool 263P Cylinder Idler Arm , 27 Cylinder Idler Bracket , 27 D Din Rail M Door Assembly M Door Glass M400784P P...19 Door Glass Seal Kit P...19 Door Graphics Door Handle Door Hinge Assembly M402714*...19 Door Latch M , 15, 19 N/A items do not appear in index. M

60 Door Ring Gasket M Door Switch M , 19 Door Switch Bracket Drive Idler Arm Drive Idler Spring Drum Idler Wheel Assembly , 27 E End Barrier M End Stop F Fan Shaft Assembly I Ignition Control M406789P...43, 45, 47, 49 Instant Electronic Ignition Valve Coil Kit M409253P...41 Instant Electronic Ignition Wire Harness Assembly , 45, 47, P...43 J Jackshaft Assembly Junction Box Cover , 45, 47, 49 K Key M M Kickplate Extension Felt Pad M Finger Guard M Front Cylinder Seal Strap P Front Panel Assembly LP Front Seal Kit P Fuse M , 45, Fuse Receptacle 91024P... 43, 45, 47, 49 G Ground Buss Assembly M H High Voltage Lead , 37, 39 Hinge Assembly M Hinge Bracket *... 13, 15, , 15, 19 Hinge Pin M L Limit Thermostat M Lint Compartment Label Lint Drawer Assembly Lint Drawer Lock Plate Lint Drawer Seal P...13, 15, Lint Screen Frame Assembly Lock and Key P...21 Lock, Key and Nut Kit P...5, 11, P...5, 11, 21 L.P. Valve Replacement Kit 868P3...35, 37, 39 M Main Harness Assembly P...43 Microprocessor Door Lock P...11 Microprocessor Wire Harness Kit P...11 N/A items do not appear in index. 58 M411988

61 Motor P Motor Capacitor M Mounting Insulation H Mounting Switch Base M412187P N Nut F M , 27, 29 M , 27, 29 M , 39 M , 23 M M Q , , , , 27, N.G. Valve Replacement Kit 867P , 37, 39 O O-Ring A Overlay Replacement Door Handle Kit P...19 Reset Thermostat P...33 Retaining Ring Rib Assembly Roller Bearing Assembly Roller Shaft Roller Shaft Retainer S Safety Wire Harness Assembly Screw M M , 27, 31 M M M M M M , , 35, 37, , , 31, , 27, , , 27, , 45, 47, , Seal Kit P...23 P Panel Key M Partition Reinforcing Plate Pop Rivet M , 15, 19, 23 M , 15, 19 Pulley Kit P... 25, 27 R Reject Button 81312J... 5, 7 Relay , 49 Seal Strap P...23 Secure Ground Label M Sensor M Shadow Box Clip M , 15 Sheave P...25, 27 Shut-Off Valve Kit P...35, 37, 39 Side and Back Cover Snap Bushing M , 35, 37, 39, 43, 45, 47, 49, 51 Spacer M N/A items do not appear in index. M

62 Spark Igniter P Spring Step Down Thermostat Stove Limit Thermostat Support Housing Bearing Assembly P Sweep Sheet Kit P Switch , , 27, Switch Plate T Terminal Block M M M , 45, 47, , 47 Thermostat Cover M Thimble and Vane Assembly P Transformer M412477P Trunnion Assembly U U-Bolt Clamp Kit P V Vane Assembly Vent and Thimble Caution Label M , 55 W Warning Label M , 55 Washer M , 27 M M M M , 25, 27, 29, N/A items do not appear in index. 60 M411988