SKS FIELD STRIPPING 101,CORROSIVE AMMO CLEANING,LUBRICATION
|
|
- Bruno Flynn
- 6 years ago
- Views:
Transcription
1 SKS FIELD STRIPPING 101,CORROSIVE AMMO CLEANING,LUBRICATION
2 We all know that the SKS gain more and more popularity everyday so i was thinking why not make a little SKS field stripping tutorial I know most of you already figured it out but think at the potential new owner! It s a beautiful Sunday and i like playing with my camera so let's begin. First of all, like any firearm, make sure it s unloaded by pulling the cocking handle back. Pull out the cleaning kit from the butt stock (if there) be careful with your finger to not get trapped with the little door
3 Unfold the bayonet to remove the cleaning rod. Unlock the magazine floor plate by pulling the latch rearward. Pull the cocking handle and slowly allow it to return in closed position. On the right side, at the rear, rotate the cover take-down lever straight up and pull it to the right.
4 Pull the cover away Remove the recoil spring from the carrier, note that the wiggled end go in the carrier. To remove the bolt carrier assembly, pull the assembly back and out of the rifle. Separate the bolt from the carrier.
5 Gas tube removal Rotate the locking lever on the right side of the rear sight. On early model, there's a little tab on the lever while on late model, only a small hole. You can take the little pick in the cleaning kit or a bullet tip to help rotate the lever. Then the hand guard can be taken away. Remove the piston from the gas tube. What we see here is the piston extension, under rear sight. To remove, push the extension and rotate the gas tube locking lever straight up then slowly allow the piston extension to come out.
6
7 Trigger group and stock removal Put the safety in "safe" position. Depress the trigger group latch, using a bullet tip or the tools in the cleaning kit. The group should pop up. Note how the front of the trigger group engages in the receiver.
8 Take the trigger group out. Take the magazine out and the stock away from the rifle. The end result is a disassembled SKS Reassemble in reverse order but make sure the front of the mag hook perfectly on the rifle and also that the pin in front of the trigger group engage correctly in the receiver or the group wont lock correctly and can lead to malfunctions.
9 Bolt disassembly on early model with the spring loaded firing pin, the extractor is taken out by pushing the extractor rearward and away from the bolt. Be very careful with the early bolt because once they are out of the bolt carrier, only the extractor pressure spring hold the extractor in place so the extractor can be easily knocked off and lost. Maybe that why the later model has a pin to hold the extractor in place but it s only a guess... Early bolt Driving this pin out, allow the removal of the firing pin and spring. Later model bolt. We can see the retaining pin just behind the extractor. The retainer is driven from the left side on the bolt. Some have removed it by using the little pointed tool from the cleaning kit and the rear cover as a hammer... but mine is very tight and require a hammer and a punch.
10 Once the pin is out, the extractor and the free floating firing pin can be taken out. Note how the firing pin goes so can be correctly reassembled, the firing pin have a notch like so the retainer can be put back on the bolt, keeping the firing pin in place but allowing to move freely in the bolt. Note the difference between early and late bolt. Bolt on the left is the early type; bolt on the right is the later type. Bolts need their specific carrier too.
11 CLEANING KIT The SKS cleaning kit is very simple and effective. Kit consist of - storage tube/cleaning rod handle -storage tube cap/cleaning rod muzzle guide -utility tool -cleaning jag -cleaning brush Cleaning kit storage tube can be used as a wrench to screw the cleaning jag on the cleaning rod. Cleaning patches are wrapped around the jag. Tube is also used as a cleaning rod handle
12 the small utility tool lock the handle and the rod together. Bore guide is well made, slide the guide on the rod before screwing the jag or the brush on the rod. Slide the guide over the muzzle and twist to lock the guide on the front sight. SKS sling installation unfasten the sling from the metal buckle and the leather keeper (if equipped)
13 the sling is passed through the swivel on the rifle, then the leather keeper and the metal buckle. Ready to attach on the rifle.
14 Adjust and tight with the leather keeper.
15 COSMOLINE CLEANING A fellow told me that would be great to share some info s on cosmoline cleaning so to make the thread more complete, here s how i de-cosmoline a SKS(and others milsurp as well) I used 2 ways to degrease a milsurp: -solvent(lacquer thinner, carb or break cleaner) -hot soapy water. Using solvent: After disassembling, using solvent to remove the Cosmoline or grease is fast and easy. A spray can of carb cleaner is useful for tight spot like the gas port and the inside of gas block. For most other parts, i use a small nylon brush and after degreasing, wipe metal with a very lightly oiled patch, and i clean the bore using the cleaning kit but with a patch soaked in solvent and few dry patch. Solvent will harm most wood finish so care must be taken to not spill any solvent on wood parts. Wearing glove and working in a well vented area is mandatory. Using soapy water: Hot soapy water, while not as fast than solvent, is still, in my opinion, a very effective way to clean off cosmo. Hot water is cheap, always available and more ecological and of course wearing glove is a must to not get burn. In my kit, i have a plastic bucket to immerge part like receiver cover, piston, mag and pretty much all s others smaller parts. For the barreled action, i use a large bucket and a funnel to pour water in the bore from breach end, in the gas block and inside of receiver. A nylon brush is used to clean the parts. I like using a cleaning rod section with a.22 jag to clean parts like the rear section of the gas tube was the piston rod go. Using boiling water heat the metal very hot and the metal dry by itself in a seconds. After the metal is dry, i wipe all with a very lightly oiled patch. I carefully wipe the wood parts with damp cloth and then a dry one. So far this method work fine for me My degreasing kit, a plastic container, brush, funnel, cleaning rod with jag and a glass pot. I like to put the gas tube partially in the glass pot filled with boiling water but only enough to immerge the tube so the wood stay out of water. The tube gets very hot quickly and the cosmo is washed away. I finish cleaning with a rod and a jag with a patch, clean the wood part with a soaked clothes then a dry cloth. Oiling the metal lightly after and keeping the gas tube dry inside before using the rifle. Having written about field strip and cosmo removal, i was asked to add info s about cleaning after corrosive ammo. I will share my procedure and also about lubrication of the SKS. Many shooters clean their rifle different ways, this is how i do it. Far from me to pretend that the way i do is the best, my method work well for me that's all i can say. I do either short cleaning or long cleaning. For short cleaning, i don t use bore solvent, i only use
16 solvent each rounds. Ok so i just shoot corrosive ammo, how i deal with that for cleaning? -First, i remove the rear cover, bolt and bolt carrier, gas tube and piston. -Boil a kettle of water, put glove on to not get burned -With the muzzle pointing down in a bucket, i pour about 1 liter of boiling water from the chamber, using a funnel, some water also in the gas block to flush any salt. -put a patch on the cleaning jag, soak the patch in water and run the patch back and forth couples of times from muzzle, using the SKS cleaning kit with the supplied muzzle guide, from the breach end, the chamber will be washed also. With another soaked patch, i wash the inside of gas tube, soaking the patch few times so the tube will be washed well, and wash the piston in the bucket of water. I also wash inside receiver and bolt face with a wet patch then wipe with a dry rag. -I put some water again down the bore for a final rinse, also in gas port too. Then i run a dry patch in the bore and in the chamber but at this point, the metal have dried by it since using boiling water dry the steel in sec. I also run a dry patch in gas tube and on the piston. If i use solvent, i do it now, if not, see the next step. -I run a very lightly oiled patch on everything that i washed with water (bore, gas tube, bolt face, piston, and interior of receiver near the chamber area) I run a dry patch to remove oil from the gas tube and the piston before next shooting. In fact, i leave so few oil in gas tube and barrel than i can shoot the rifle anytime, the metal really only need a smear trace of oil to protect from rust, i don t leave in a humid climate so seems to work well for me but your mileage may vary. Funnel used to flush the bore A bit of water will rinse the gas port well. In fact, that procedure is way longer to write than actually do it. Its matter of wash, dry, use bore cleaner and/or oil.
17 LUBRICATION About lubrication, the SKS don t need lube to work unlike many others rifles. All that said, few drops of oil never hurt but for me less is better. To be noted that in winter, i keep the rifle oil free so nothing will get frosty. In the next pics, that's where i like to use oil and only 1 or 2 drops are enough. I use regular gun oil. Note that the gas system should be kept dry. Mounting point of the gas tube Piston extension and spring, recoil spring bolt carrier side groove hammer face
18 Hammer spring, hammer pivot, sear/mag catch spring, trigger pin and trigger spring. That's it!
Sanitise Syrup Lines & Valves. Taylor PH61 Cleaning every 14 days
Taylor PH61 Cleaning every 14 days Drain the Syrup Lines Remove each syrup feed tube from syrup bottle and let excess syrup drain from the feed tube back into the syrup bottle. When flow of syrup from
More informationSuperKlean Washdown Products
February 2012 DURAMIX 8000 INSTALLATION AND MAINTENANCE INSTRUCTIONS **DO NOT THROW AWAY AFTER INSTALLATION** **SAVE AND DISPLAY PROMINENTLY WHERE THIS EQUIPMENT IS USED** WARNING HIGH PRESSURE AND HOT
More informationUser s Manual. Electric Kettle Model MJ-EK5AEU (UK) Household Use
Electric Kettle Model MJ-EK5AEU (UK) Household Use User s Manual Thank you for your purchase. Please read this User s Manual before using this product. Retain this User s Manual for future reference. Contents
More informationCERTI CRIMP Hand Crimping Tool is used to crimp the closed end splices onto the wire sizes listed in Figure 1.
Figure 1 CERTI CRIMP Hand Crimping Tool 48087 is used to crimp the closed end splices onto the wire sizes listed in Figure 1. Reasons for reissue of this instruction sheet are provided in Section 7, REVISION
More informationπ H-2268 SANITAIRE UPRIGHT VACUUM SAFETY uline.com
π H-2268 SANITAIRE UPRIGHT VACUUM 1-800-295-5510 uline.com SAFETY PAGE 1 OF 7 NOTE: When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS
More informationExplorer CleaningPartsDirect.com Carpet Extractor. Operator and Parts Manual. Home Find... Go To.. Model No.: Can.
Explorer 1500 Carpet Extractor Model No.: 608808 609231 Can. Operator and Parts Manual CleaningPartsDirect.com 662-393-3045 NOBLES 12875 RANSOM STREET HOLLAND MI 49424 U.S.A. CUSTOMER SERVICE: 1-800-365-6625
More informationReasons for reissue are provided in Section 6, REVISION SUMMARY.
Reasons for reissue are provided in Section 6, REVISION SUMMARY. The FRONT OF TOOL has the AMP marking on the link. The BACK OF TOOL (Wire Side), into which the wire is inserted, has the wire size marked
More informationMANUAL OWNER S. Operating and Servicing Instructions IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE.
OWNER S MANUAL Operating and Servicing Instructions www.hoover.com.hk HW-FM-HKA IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE. THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. IF USED COMMERCIALLY
More informationBMW E36 Thermostat Removal And Coolant Flush
BMW E36 Thermostat Removal And Coolant Flush Disclaimer: The cooling system is critical to the proper operation of your car. Failure to properly install all of the components of the cooling system could
More informationDetailed Cleaning Instructions
NY Thermal Inc. Tel: (06) 67-6000 Toll Free: 1-800-688-27 Fax: 1-06-432-113 Web: www.ntiboilersl.com Email: info@ntiboilers.com Style Heat Exchanger occupants or, death. This boiler must be serviced by
More informationQuickSteamer USER S GUIDE 1950 SERIES QUICKSTEAMER 2050 SERIES QUICKSTEAMER POWERBRUSH. Safety Instructions. Product View. Assembly/Accessories 6-9
QuickSteamer USER S GUIDE 1950 SERIES QUICKSTEAMER 2050 SERIES QUICKSTEAMER POWERBRUSH 3 Safety Instructions 4 Product View 5 Assembly/Accessories 6-9 Operations / Special Tools 10 Routine Maintenance
More informationInstructions for Installing the MMD Rear Window Louvers
Instructions for Installing the MMD Rear Window Louvers Time Required: Less than 1 hour of labor (5 hours total installation if the 4 hours of letting the brackets set are included). Required Tools: Socket
More informationMC-V Vacuum Cleaner. Specifications are subject to change without notice for further improvement.
Order Number MAC0506027C1 Vacuum Cleaner MC-V7314-01 Specifications are subject to change without notice for further improvement. 2005 PANASONIC CONSUMER ELEC- TRONICS COMPANY, DIVISION OF PANA- SONIC
More information1350 & AMMCO Brake Washer Systems. Installation and Operating Instructions With Safety and Maintenance Instructions and Parts Identification
1350 & 1450 AMMCO Brake Washer Systems Installation and Operating Instructions With Safety and Maintenance Instructions and Parts Identification READ these instructions before placing unit in service.
More informationMANUAL VERSION SERIAL # X-1 MINI PRO OWNER S MANUAL ASSEMBLY & OPERATOR INSTRUCTIONS 1.0
SERIAL # MANUAL VERSION 1.0 Introduction WARNING: To limit risk of potential injury and material damage, all users must read these instructions in their entirety and follow them strictly. Check our YouTube
More informationUnderstanding Clean Carburetors. Understanding Carburetors
Understanding Clean Carburetors This guide is borrowed from the forum at Gixxer.com, was written by Rob (Old Skool_R), and he is solely responsible for its content. The only editing I have done is to remove
More information5.0 cu ft Electric Concrete Mixer
Save This Manual for Future Reference 5.0 cu ft Electric Concrete Mixer Operator s Manual MODEL NUMBER YM0146 SERIAL NUMBER PURCHASE DATE Both model number and serial number may be found on the main label
More informationHot Chocolate Dispenser
Hot Chocolate Dispenser Instruction manual Model: CN219-A AU Telephone Helpline: 1300225960 Safety Tips Position on a flat, stable surface. A service agent/qualified technician should carry out installation
More informationCorrosion Resistant Alloy Running Procedures with Eckel Tongs and Non-Marking Grit Faced Dies
Corrosion Resistant Alloy Running Procedures with Eckel Tongs and Non-Marking Grit Faced Dies Eckel Hydraulic Power Tongs, Power Units, and Accessories Eckel Running Procedures for Corrosion Resistant
More informationW / E / W / E / $10.00
1 $10.00 30 9.0 General maintenance 9.1 Daily (whenever using the heater) 9.1.1 open main viewing door The front of the heater becomes very hot during operation. Let the heater cool completely before A.
More informationMODEL SK2660 COMPRESSOR SERVICE KIT. For use on 2660 and 2680 Model Compressors
MODEL SK2660 COMPRESSOR SERVICE KIT For use on 2660 and 2680 Model Compressors WARNING: Unplug the compressor before beginning disassembly. CAUTION: Improper assembly or use of damaged parts may lead to
More informationMODEL SK2660 COMPRESSOR SERVICE KIT. For use on 2660 and 2680 Model Compressors
MODEL SK2660 COMPRESSOR SERVICE KIT For use on 2660 and 2680 Model Compressors WARNING: Unplug the compressor before beginning disassembly. CAUTION: Improper assembly or use of damaged parts may lead to
More informationHydraulic Crimping Heads and
Hydraulic Crimping Heads 58422-1 and 2161730-1 Instruction Sheet 408-9535 30 MAY 17 REV D 1. INTRODUCTION Figure 1 This instruction sheet covers application, inspection and maintenance procedures for Crimping
More informationCapraLite. Owner s Manual. Milking Machines. Built by: Apparatus Mfg., Inc. 13 Commerce St Poughkeepsie, NY 12603
CapraLite Milking Machines Owner s Manual www.capralite.com Built by: Apparatus Mfg., Inc. 13 Commerce St Poughkeepsie, NY 12603 Page 2 Getting your Machine ready Your machine is almost ready to use. For
More informationAGITATOR V DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THESE INSTRUCTIONS IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY
AGITATOR 20 120V INFORMATION & OPERATING INSTRUCTIONS DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THESE INSTRUCTIONS IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY 1. Always use
More informationFood Waste Disposer Instruction Manual
Food Waste Disposer Instruction Manual See insert for specific information about your new disposer NOTE: IMPORTANT: CAUTION: This Food Waste Disposer has been designed to operate on 110-120 Volt, 60 Hz
More informationUsed Fluid Handling Portable Used Oil Gravity Drains
Portable Used Oil Gravity Drains Choose the fluid handling equipment that fits your needs. Traditional Drain: the traditional method for handling used fluids allows gravity to drain fluids from vehicle(s)
More informationTC-720 RECYCLING BALER
OPERATING AND MAINTENANCE INSTRUCTIONS TC-720 RECYCLING BALER READ INSTRUCTIONS THOROUGHLY BEFORE OPERATING Sept. 06, 2013 3451 S. 40th Street Phoenix, AZ 85040 602.437.5020 800.223.4540 www.tsissg.com
More informationMODEL SK2750. COMPRESSOR SERVICE KIT For use on 2750 Series Compressors
MODEL SK2750 COMPRESSOR SERVICE KIT For use on 2750 Series Compressors WARNING: Unplug the compressor before beginning disassembly. CAUTION: Improper assembly or use of damaged parts may lead to premature
More informationSAAB 99 Series H Type Engine. Installation Guide Silicone Cooling System Hoses. Classic Silicone Hoses
SAAB 99 Series 1981 1984 H Type Engine Installation Guide Silicone Cooling System Hoses Classic Silicone Hoses http://www.classicsiliconehoses.com/ Disclaimer This document is for reference purposes only.
More informationINSTANT HOT WATER DISPENSER
INSTANT HOT WATER DISPENSER Tank Installation Materials required (not provided) 2 mounting bracket screws (and 2 plastic anchors if attaching to drywall) Shut-Off valve and T fitting Components When you
More informationENVIRONMENTAL STANDARD OPERATING PROCEDURE 23 WEAPONS CLEANING
ENVIRONMENTAL STANDARD OPERATING PROCEDURE 23 WEAPONS CLEANING 1. Version, Date. 1, 6 June 2012 2. Purpose. This Environmental Standard Operating Procedure (ESOP) summarizes the procedures implemented
More informationUsed Fluid Handling Portable Used-Oil Gravity Drains
Portable Used-Oil Gravity Drains Choose the fluid handling equipment that fits your needs. Traditional Drain: the traditional method for handling used fluids allows gravity to drain fluids from vehicle(s)
More informationInstallation & Operating Guide
5-036 HOT WATER TANK Installation & Operating Guide Read all instructions thoroughly. Keep this guide for future reference. Proof of purchase is required for Warranty. Staple receipt or proof of purchase
More informationA GUIDE TO LOOKING AFTER YOUR WINDOWS AND DOORS
A GUIDE TO LOOKING AFTER YOUR WINDOWS AND DOORS W I N D O W S D O O R S C O N S E R V A T O R I E S www.spectus.co.uk The difference is clear to see OUR TOP TIPS TO KEEP YOUR WINDOWS IN THE BEST CONDITION
More informationSAFETY IN THE KITCHEN--
SAFETY IN THE KITCHEN-- Discover... how to identify safety hazards in the kitchen. how to prevent kitchen accidents. Key Terms flammable poison control center A ccldento don't just happen. They': caused
More informationHydraulic Crimping Head, PN 69069
Hydraulic Crimping Head, PN 69069 Instruction Sheet 408-1745 31 JUL 17 Rev F 1. INTRODUCTION Figure 1 This instruction sheet covers application, inspection and maintenance procedures for DYNA-CRIMP* Crimping
More informationPackardInfo.com. HOW TO: Rebuild a Trico Mag Nu Matic Vacuum Washer Pump. Introduction
Introduction So here hopefully ends the saga of my Trico Mag Nu Matic washer pump. I found the pump at the 2009 Packards International swap meet for $35. I thought I had the deal of a lifetime as it looked
More informationCHLORIDE GASES CHLORIDES
Note: Always have this machine s model and serial number (printed on the first page of this document) ready when calling Consolidated for service or parts. WARNING If this sterilizer s chamber is constructed
More informationModel K 4400 G Part No High Pressure Washer
Model K 4400 G Part No. 1.133-208.0 High Pressure Washer Table of Contents Overview..................................1 Precautions...............................1-2 Assembly Instructions.........................3
More informationXLT-60 EXTRACTOR 120V CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THIS INSTRUCTION MANUAL
XLT-60 EXTRACTOR 120V INFORMATION & OPERATING INSTRUCTIONS CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THIS INSTRUCTION MANUAL 56041883 IMPROPER USE OF THE MACHINE WILL VOID THE
More informationTHERMO POT MODEL: ETP-C3211(WH) Owner s Manual. Please read this manual carefully before operating your set. Retain it for future reference.
THERMO POT MODEL: ETP-C3211(WH) Owner s Manual Please read this manual carefully before operating your set. 1 Retain it for future reference. Record model number and serial number of the set. See the label
More informationSection 10: Customer Care Guidance
48 Section 10: Customer Care Guidance Please note that although these units have been designed to give years of pleasure and satisfaction, you can advise the customer to help maintain the original beauty
More informationOperating, cleaning and maintenance guide
Operating, cleaning and maintenance guide For alternative formats visit the Residents Zone www.anglian-building.co.uk Contents Introduction 3 Opening and closing windows 4 Outward-opening casement windows
More informationCBT LW MAINTENANCE GUIDE
CBT LW MAINTENANCE GUIDE PICTOGRAMS Each Signifier displayed here is specific to this User Manual. Menu Previous Advance Note Tip Example Powder Feeder Mixing Bowl Weigh Scale CBP Tanks Control Panel PSD
More informationPortable Pressure Washer
RX550i Thanks for purchasing our latest portable pressure washer. Whether it be for light rinsing or for power stripping, this pressure washer is built for quick and easy high speed cleaning. To get the
More informationOPERATING and MAINTENANCE INSTRUCTIONS Models: H138NPSCLCMCQRL Merchandising Hot Cabinets
Rev. (/) Page of 0 OPERATING and MAINTENANCE INSTRUCTIONS Models: H8NPSCLCMCQRL Merchandising Hot Cabinets Cabinet model number: Cabinet serial number: Authorized Service Agency: Ph: Fax: Keep this manual
More informationDO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THE INSTRUCTIONS IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY
KING COBRA 500 120V INFORMATION & OPERATING INSTRUCTIONS DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THE INSTRUCTIONS IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY 1. Always use
More informationCleaning and Sanitation Procedures Module Cafe/Dining Restroom
Cafe/Dining Restroom Restrooms Materials Requirement Planning A. Materials requirement planning (MRP) a. Clean rags b. Mop buckets and wringers c. Cotton wet mops and handles d. Dust mop and dustpan e.
More informationFloormate Deluxe Let s get started
Floormate Deluxe Let s get started HF86-FM-D vax.co.uk Let s talk safety Please keep instructions for further use. This Floormate is intended for household use only and NOT for commercial or industrial
More informationHeavy Head Hand Tools , , , and AUG 15 Rev K
Instruction Sheet 408-1261 Heavy Head Hand Tools 59239-4, 59239-8, 59287-2, and 525692 27 AUG 15 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered
More informationHydraulic Crimping Head, PN
Hydraulic Crimping Head, PN 1673672-1 Instruction Sheet 408-8910 14 JUL 17 Rev C PROPER USE GUIDELINES Cumulative trauma disorders can result from the prolonged use of manually powered hand tools. Hand
More informationI N ST R UC T I ON MODEL 2612 & 2712 SLICERS MODELS 2612 ML ML FORM (12-98) 2612 SLICER
I N ST R UC 2612 SLICER T I ON S MODEL 2612 & 2712 SLICERS MODELS 2612 ML-104829 2712 ML-104822 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 34141 (12-98) Installation, Operation, and Care of MODEL 2612
More informationFG800SS #8 MEAT GRINDER
FG800SS #8 MEAT GRINDER For your safety and continued enjoyment of this product, always read the instruction book carefully before using. IMPORTANT SAFEGUARDS (Keep care use guide for future reference)
More informationSoft Serve Ice-Cream Machines
Soft Serve Ice-Cream Machines How To Clean, Lubricate and Reassemble Your Gravity Fed Machine Please follow these start-up instructions every time you clean your machine For Spaceman Ice Cream Machines
More informationAltra Series Dampener
Crestline TM Altra Series Dampener Installation Instructions Heidelberg MO X88-66 10/97 Rev-A GENERAL INFORMATION ATTENTION CRESTLINE ALTRA SERIES TM DAMPENER OWNER! Accel Graphic Systems provides parts
More informationHere is my experience and a few things I learned about my metallic epoxy floor install purchased from
Here is my experience and a few things I learned about my metallic epoxy floor install purchased from http://www.garageflooringllc.com This was my first dealings with metallic epoxy. Overall I am happy
More informationSTART-UP AND CLEAN-UP PROCEDURES
How-To Guide BI-AE-TM 5-15 START-UP AND CLEAN-UP PROCEDURES S T A R T - U P 1 2 3 Centralize the machine to make sure your hose reaches the areas to be sprayed. Open a bucket of ECOSEAL Plus TM and place
More informationlast editted by: Yuyang Chen last edited: 3/12/20152:52:00 PM Page 1 of 1
Name Refill friction stir spot welder Description RPS 100 spot friction welding system Valid from software version V02.21 Manufacturer and Harms & Wende GmbH & Co KG Model Location E3 2118J SOP Creation
More informationLubrication Tools and Equipment Portable Oil Drains
Portable Oil Drains Choose the fluid handling equipment that fits your needs. Traditional Drain: the traditional method for handling used fluids allows gravity to drain fluids from vehicle(s) into a portable
More informationMODEL COMPRESSOR SERVICE KIT For use on Midmark Power Air Oil-less Compressor Models P21, P22 & P32
MODEL 77001616 COMPRESSOR SERVICE KIT For use on Midmark Power Air Oil-less Compressor Models P21, P22 & P32 WARNING: Unplug the compressor before beginning disassembly. CAUTION: Improper assembly or use
More informationFume Free Casting Box
Fume Free Casting Box Contributed by: Mark James A.K.A mark james This tutorial was downloaded from http://www.penturners.org The International Association of Penturners - 2014 FUME FREE CASTING BOX by
More informationQuickSteamer USER S GUIDE 1950 SERIES 6-8. Safety Instructions. Product view. Assembly. Operations / Special Tools. Routine Maintenance
QuickSteamer USER S GUIDE 1950 SERIES 3 Safety Instructions 4 Product view 5 Assembly 6-8 Operations / Special Tools 9 Routine Maintenance 10 Troubleshooting 10 Consumer Services 11 Replacement Parts 12
More informationJUL 17 Rev C
Hydraulic Crimping Head, PN 1752787-1 Instruction Sheet 408-8914 31 JUL 17 Rev C 1. INTRODUCTION Products Crimped AMPLI-BOND* and PLASTI-GRIP* Terminals TERMINYL* Terminals and Splices Pre-Insulated AMPOWER*
More informationA guide to looking after your windows, doors and conservatories. spectus n. look, appearance, aspect
A guide to looking after your windows, doors and conservatories Our top tips to keep your windows in the best condition We recommend That you carry out routine maintenance on your windows, doors and /
More informationCOMBINATION SAFES BIOMETRIC LOCK SAFES
GUN STORAGE In the United States, owning a gun is a part of the nation s heritage, written into the supreme law of the land the Constitution. But exercising Second Amendment rights also requires exercising
More informationThe Hop Stopper 2.0 User s Guide
The Hop Stopper 2.0 User s Guide Designed and Manufactured by Innovative Homebrew Solutions Congratulations! You are now the owner of the newest and best kettle screen offered to the homebrewer. The Hop
More informationSingle- Action Double- Action
Single- Action Double- Action Instruction Sheet (SADA) Hand Tools 45730, 408-1532 46467, 46468, 46469, and 46470 04 AUG 09 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged
More informationINSTALLATION INSTRUCTIONS
,t_2007 Lennox Industries Inc. Dallas, Texas, USA INSTALLATION INSTRUCTIONS CH33 Series Units EVAPORATOR 505,264M (65484504) 10/07 Supersedes 09/06 COILS n _putech blications ical Litho U.S.A. RETAIN THESE
More informationModel K 3000 G Part No
K3000G Manual 11/30/01 4:56 PM Page 1 Model K 3000 G Part No. 1.133-110.0 High Pressure Washer Operator Manual Overview..................................1 Precautions...............................1-2
More informationIndustrial Science Seminar
Equipment Maintenance A. Automatic Scrubbers 1) Battery-operated power equipment, like an automatic floor scrubber, needs special care and maintenance. See owners manual before proceeding. 2) These units
More informationOPERATOR'S MANUAL HD-400
STATEMENT OF LIMITED WARRANTY MÁQUINAS AGRÍCOLAS JACTO S.A. shall warrant the equipment described in this manual and shall repair or replace parts and components which, under normal operation and wear,
More informationTECHNOLOGY IN MOTION MACO PROTECT DOOR LOCKS. Operating and maintenance instructions for door locks END USERS
TECHNOLOGY IN MOTION MACO DOOR LOCKS Operating and maintenance instructions for door locks END USERS Table of Contents Proper use and misuse 3-4 Safety and warning information 5-6 Operating instructions
More informationOperation and Safety Manual. Model LNKB15. Planetary Mixer. Medium Duty; Gear-driven; Manual operation
Medium Duty; Gear-driven; Manual operation Model LNKB15 Planetary Mixer DO NOT ATTEMPT TO OPERATE THIS MACHINE UNTIL YOU HAVE READ AND UNDERSTOOD THIS OPERATION AND SAFETY MANUAL. SAFETY ISSUES 1. NEVER
More information82. Siphon all gas out of the tank. 83. Disconnect the fuel filler and vent tube with a Phillips screwdriver.
Chapter 5 - Gas Tank Removal, Cleaning, Sealing (Video Clip 5) 81. Gas tank removal and cleaning and sealing was completed using the Eastwood Gas Tank Sealer Kit. Other items required included (Purchase
More informationOPERATOR'S MANUAL HD-500/550
STATEMENT OF LIMITED WARRANTY MÁQUINAS AGRÍCOLAS JACTO S.A. shall warrant the equipment described in this manual and shall repair or replace parts and components which, under normal operation and wear,
More informationArmstrong J Series Float, Thermostatic Steam Traps, Condensate Controllers & Liquid Drainers Installation and Maintenance Manual
Armstrong J Series, Thermostatic Steam Traps, Condensate Controllers & Liquid Drainers Installation and Maintenance Manual This bulletin should be used by experienced personnel as a guide to the installation
More informationHow to care for your. Includes key fob & plaque
How to care for your Includes key fob & plaque Welcome to your new Synseal Complete Conservatory. Now you ve been handed the keys, it s important to take a little time to read through this guide so you
More informationInstallation Instructions
Aluminum Blinds Installation Instructions Echelon, Traditions & Integra Aluminum Blinds 2 Metro Aluminum Blinds *Click on any page to return to the Table of Contents* Echelon, Traditions & Integra Aluminum
More informationMX-DS1 Desoldering Gun for the MX-500P & MX-5200 Series
Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com MX-DS1 Desoldering Gun for the MX-500P & MX-5200 Series MX-DS1 U ser Guide Copyright OK International,
More informationCleaning and Sanitation Procedures Module Deli
Deli Triple Sink System (Clean, Rinse, Sanitize) A. Preparation 1) Wash your hands with anti-microbial soap before and after cleaning and whenever hands are dirty. 2) Dawn appropriate PPE s 3) Place safety
More informationGETZ MANUFACTURING PART NO.: MODEL: SV1 100 PR VACUFILL SYSTEM (Revised 6/7/05)
GETZ MANUFACTURING PART NO.: 58616 MODEL: SV1 100 PR VACUFILL SYSTEM (Revised 6/7/05) GETZ SV1-100-PR VACU-FILL SYSTEM TABLE OF CONTENTS PAGE # 1... GETZ SV1-100-PR VACU-FILL SYSTEM 2... PARTS LIST 3...
More informationThermal Steel Care & Maintenance Guide
Thermal Steel Care & Maintenance Guide Introduction Arcadia Custom Thermal Steel products require regular and proper inspection, cleaning and maintenance before, during and after installation in order
More informationNilfisk Inc Winnetka Avenue North Minneapolis, MN REV.03( ) VF80189
Nilfisk Inc. 9435 Winnetka Avenue North Minneapolis, MN 55445 www.usviper.com REV.03(05-) VF8089 SAFETY PRECAUTIONS This machine is intended for commercial use. It is constructed for use in an indoor
More informationTHERMO POT MODEL: ETP-D4013(WH)/ ETP-D5013(WH)/ ETP-D6013(WH) Owner s Manual. Please read this manual carefully before operating your set.
THERMO POT MODEL: ETP-D4013(WH)/ Owner s Manual ETP-D5013(WH)/ ETP-D6013(WH) Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial
More informationINSTRUCTION MANUAL W-400
USE and MAINTENANCE INSTRUCTION MANUAL Bellaria WBX WB GRAVITY SPRAY GUN Series LPH-400 WB en it fr es pt de se TECHNICAL DATA Classic Plus Series LPH-400 (LVLP) Classic Plus Nozzle_Needle set Combination
More informationProduct View. Assembly. Operation. Maintenance and Care. Troubleshooting. Consumer Services. Replacement Parts. Additional Accessories.
U S E R S G U I D E 76R9 Series 3 Safety Instructions 4 Product View 5 Assembly 5-7 Operation 8 Maintenance and Care 9 Troubleshooting 10 Consumer Services 11 Replacement Parts 11 Additional Accessories
More information9780 SW Freeman Dr. Wilsonville, OR USA Tel: Fax: crimsontrace.com Rev002 12/15
9780 SW Freeman Dr. Wilsonville, OR 97070 USA Tel: 800-442-2406 Fax: 503-783-5334 crimsontrace.com 27-1499 Rev002 12/15 MVF-515 MODULAR VERTICAL FOREGRIP INTEGRATED LASER/LIGHT USER S MANUAL FOR RED &
More informationClean Water Made Easy. CWS Time Clock Softener Installation & Start Up Guide. Questions?
Clean Water Made Easy www.cleanwaterstore.com CWS Time Clock Softener Installation & Start Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
More informationHH80C HYDRAULIC CRIMP TOOL
HH80C HYDRAULIC CRIMP TOOL DATASHEET SEE PAGE 8 FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY INTRODUCTION: The HH80C is a hand actuated hydraulic crimp tool designed
More informationGETZ EQUIPMENT INNOVATORS PART NO.: 9G58619 MODEL: SV1 150 PR VACUFILL SYSTEM (Revised 2/25/14)
GETZ EQUIPMENT INNOVATORS PART NO.: 9G58619 MODEL: SV1 150 PR VACUFILL SYSTEM (Revised 2/25/14) !!WARNING!! SEVERE DAMAGE AND/OR INJURY MAY RESULT DO NOT DISCHARGE ANY EXTINGUISHER CYLINDER EXCEEDING 195
More informationCollecting and Shooting the Military Surplus Rifle (2005) -Surplusrifle.com. Cosmoline Removal! Adobe PDF Downloadable Version of Article
Page 1 of 15 Cosmoline Removal! Article Contributed by: Jamie Mangrum Adobe PDF Downloadable Version of Article I am astonished that it has taken us this long to publish something on Cosmoline removal
More informationMERCHANT POPCORN MACHINE SERVICE MANUAL
3243 North California Avenue, Chicago, IL 60618 MERCHANT POPCORN MACHINE SERVICE MANUAL 120 Volt, Single Phase, 60 Hz 230 Volt, Single Phase, 50 Hz READ and UNDERSTAND this servicing, and safety instructions
More informationOPERATOR'S MANUAL HD-400
STATEMENT OF LIMITED WARRANTY MÁQUINAS AGRÍCOLAS JACTO S.A. shall warrant the equipment described in this manual and shall repair or replace parts and components which, under normal operation and wear,
More information5200 Flip-!t & 7340 Flip-!t Select Series
2 Thanks U S E R S G U I D E 5200 Flip-!t & 7340 Flip-!t Select Series 3 Consumer Services 4 Safety Instructions 5 Product View 6 Features / Assembly 7-8 Operation 9-10 Clean-Up Storage 10 Troubleshooting
More informationUSER'S GUIDE 19K8 SERIES V
USER'S GUIDE 19K8 SERIES 220-240V 2 Thank You 3 Safety Instructions 4 Product View 5 Assembly 5-7 Operations 8 Maintenance and Care 9 Troubleshooting 10 Replacement Parts 11 Warranty 12 Consumer Services
More informationOWNER S MANUAL. Models: Herkules Equipment Corporation 2760 Ridgeway Court Walled Lake, MI USA Fax
Part# 1000692 7/12/99 tn INSTRUCTIONS This manual contains important information concerning the installation and operation of the gun washers listed at the right. Read manual thoroughly and keep for future
More informationElectric Honey Extractor
Electric Honey Extractor Instruction Manual SKU: BEE-V004E Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/bee-v004e
More informationFrontload Washer. Preventative Maintenance.
Frontload Washer Preventative Maintenance www.comlaundry.com Part No. 6-07-177R1 October 2008 Table of Contents Daily...2 Monthly...4 Quarterly...7 Bi-Annually...9 Daily Preventative Maintenance Checklist...11
More informationChiller with BP-1 1/2 oz Pump
Chiller with BP- / oz Pump MODEL: CCP CHILLER WITH BP- / OZ PUMP 800 0V BP- / OZ PUMP ONLY 888 Thank You...for purchasing our Chiller with / oz Pump. This quality, NSF listed pump delivers precise, chilled
More information