Product Data. FB4C Base Series Fan Coil Sizes 018 thru 060 AIR HANDLER TECHNOLOGY AT ITS FINEST

Transcription

1 Base Series Fan Coil Sizes 018 thru 060 Product Data AIR HANDLER TECHNOLOGY AT ITS FINEST A10082 The fan coil combines the proven technology of Carrier fan coil units with the flexibility to handle both Puron refrigerant and R -22, as well as vertical and horizontal applications. The design features contoured condensate pans with rugged drain connections, ensuring that little water is left in the unit at the end of the cooling duty cycle. The lack of standing condensate and corrosion free pans improves IAQ and product life, features homeowners appreciate. Standard features include grooved copper tubing and louvered aluminum fins. Coil circuiting has also been updated to make the most of all Carrier heat pumps and air conditioners. Units come with solid state fan controls, 1 -inch (25mm) thick insulation with R -value of 4.2, multi -speed motors, and fully -wettable coils. Units can accommodate factory - and/or field -installed heaters from 3 to 30 kw. It also should be noted that the unique cabinet design of these fan coils meet new stringent regulations for cabinet air leakage - a requirement of 2% cabinet leakage rate when tested at 1.0 inches of static pressure. The fan coil design is loaded with popular features. These fan coils utilize the latest in electronic commutation motor (ECM) technology through the use of high efficiency, X13, blower motors, allowing reliable air delivery with increased static pressure. It comes in a pre -painted (taupe metallic) galvanized steel casing and a factory -supplied power plug for ease of installation. ArmorCoatt provides a tin plating of the indoor coil s copper hairpins. This creates a barrier between the corrosion -causing elements and the coil. The unit is shipped with a factory -installed Teflon -ring piston (018 thru 048) or a Puron refrigerant TXV (060).

2 STANDARD FEATURES S High efficiency ECM (electronic commutating motor) X13 motors - all sizes S Integrated motor controls have replaced integrated circuit board S Five available speed tags to meet a wide range of applications S Large, grooved tube, louvered fin coils S Efficient, quiet, time-tested blower housings and diffusers S Sturdy, drainable condensate pans S Cabinet construction features innovations designed to prevent cabinet sweating S Tested for condensate disposal in much tougher conditions than Air Conditioning and Refrigeration Institute requirements S Super-thick R -4.2 insulation with vapor barrier S Pre -painted galvanized steel cabinet (taupe metallic) S Cabinet design meets stringent regulations for 2% cabinet leakage rate when tested at 1.0 inches static pressure S Installation -flexible, multipoise units S Horizontal hanging provisions on cabinet S No tools required to access filter S Newly improved filter rack area filter door insulation added for improved air seal S Factory -installed heater packages available (5 - through 15 -kw) S 3 - through 30 -kw accessory heaters - field installed S Factory -supplied power plug S Easy plug -in provisions for heater installation S Entry options for high and low voltage wiring hook -up S Easy coil inspection (removable, snap -in plug on A -coil models) S Leak -preventing sweat connections S Puron refrigeration factory -installed Teflon -ring pistons (18 thru 048) or thermostatic expansion valve, TXV, (060) S Designed for manufactured housing applications. ADDITIONAL FEATURES S S Factory -installed heater packages available ArmorCoatt coil protection available 2

3 MODEL NUMBER NOMENCLATURE F B 4 C N F Product Heating Size Fan Coil 00 = No Heat 05 = 5 kw Type 75 = 7.5 kw E=Infinity,Variablespeed,Puron 08 = 8 kw V = Performance, Variable speed, Puron 10 = 10 kw X --- Comfort, Puron 11 = 11 kw B = Base, Puron --- Piston 15 = 15 kw Y = Base --- Puron --- Piston F = Through --- the --- wall Coil Coating H=ElectricFurnace 0=Standard T=ArmorCoatt Position 1=Upflow Capacity 4=Multipoise 018/019 = 18,000 5 = Upflow/downflow 024/025 = 24, /031 = 30,000 Series 036/037 = 36,000 A, B, C, D, E 042/043 = 42, /049 = 48,000 Electrical 060/061 = 60,000 N /230v, 1 ph, 60 Hz 001 = 18, ,000 S = 230v, 1 ph, 50 Hz 002 = 18, , = 24, ,000 Cabinet Style 004 = 24, ,000 B --- Modular Cabinet (2 piece) 005 = 30, ,000 F --- Single Piece 006 = 36, ,000 ISO 9001:2000 the environmentally sound refrigerant Use of the AHRI Certified TM Mark indicates a manufacturer s participation in the program For verification of certification for individual products, go to REGISTERED 3

4 DIMENSIONS SHIPPING WT SHIPPING WT COIL UNIT A B C D E F G H J (LBS) (LBS) CONFIGURATION SLOPE "A" NON TIN-COATED TIN-COATED NF /16" 14 5/16" 12 7/16" 12 5/16" 10 7/16" 18 1/8" 18 5/8" - 12" X NF /16" 14 5/16" 12 7/16" 12 5/16" 10 7/16" 18 1/8" 18 5/8" - 12" X NF /8" 17 5/8" 15 3/4" 15 5/8" 15 3/8" 23 1/8" 23 5/8" - 17" X NF /8" 17 5/8" 15 3/4" 15 5/8" 15 3/8" 23 1/8" 23 5/8" - 17" X NF /8" 21 1/8" 19 1/4" 19 1/8" 15 11/16" 23 7/16" 23 1/8" X NF /8" 21 1/8" 19 1/4" 19 1/8" 15 11/16" 23 7/16" 23 1/8" X NF /16" 21 1/8" 19 1/4" 19 1/8" 19 1/2" 27 1/4" 26 15/16" X NOTE: 1. SERIES DESIGNATION IS THE 14TH POSITION OF UNIT PRODUCT NUMBER NOTE: ALLOW 21" FROM FRONT FOR SERVICE 2. ALL DIMENSIONS ARE IN "INCHES" UNLESS NOTED. UNIT CONNECTION SIZES SUCTION: 018 & 024-5/8" I.D. SWEAT 030 & 036-3/4" I.D. SWEAT 042 THRU 060-7/8" I.D. SWEAT LIQUID: 3/8" I.D. SWEAT CONDENSATE: 3/4" FPT 2 1/8" 10 3/16" 1" 22 1/16" 11" OUTLET AIR 7/8" 3/4" 1 7/8" 7/8", 1 3/32" 2" DIA. K.O.'S FOR HIGH VOLTAGE POWER WIRING 7/8"DIA. K.O. FOR LOW VOLTAGE CONTROL WIRING ALTERNATE 7/8"DIA. K.O. FOR LOW VOLTAGE CONTROL WIRING A ALTERNATE 7/8",1 3/32",2"DIA. K.O.'S FOR HIGH VOLTAGE POWER WIRING OPPOSITE SIDE OPTIONAL FIELD CONVERTED RIGHT SIDE RETURN OPENING (SLOPE COIL UNITS ONLY) NOTE: MODULAR UNITS WILL HAVE A TWO-PIECE CABINET 1 1/2" 15/16" 1 15/16" 1" TOP VIEW B C 1 3/8" 1 3/16" 19" J H MAX FOR MODULAR UNITS DISCONNECT OR CIRCUIT BREAKER LOCATION 1 3/4" BLOWER, CONTROL, & ELECTRIC HEATER ACCESS PANEL 1 1/4" OPENING 19 13/16" RIGHT SIDE VIEW 2 1/2" INLET AIR COIL ACCESS PANEL INLET AIR 2 5/8" FITTING PANEL LIQUID LINE CONNECTION SUCTION LINE CONNECTION 4 11/16" 3 1/16" LIQUID LINE CONNECTION E LIQUID LINE CONNECTION 10 7/16" 6 3/16" 10 3/4" 9 1/2" SUCTION LINE CONNECTION 1" 5" OPENING FRONT VIEW SHOWN WITH "A" COIL DETAILS CONNECTION LOCATIONS FOR UPFLOW OR HORIZ. APPLICATIONS D INLET AIR FILTER ACCESS PANEL SLOPE COIL DETAILS CONNECTION LOCATIONS SHOWN FOR UPFLOW OR HORIZ. LEFT APPLICATIONS ACCESS PANEL CONFIG. FOR SLOPE COILS DOWNFLOW OR HORIZ. RIGHT APPLICATIONS AND "A" COILS DOWNFLOW APPLICATIONS Fig. 1 - NF - English A

5 DIMENSIONS (cont.) NOTES: 1. CONDENSATE PAN DRAIN CAPS NOT SHOWN FOR CLARITY. 2. ALL DIMENSIONS ARE IN "INCHES" UNLESS NOTED. SLOPE COIL AIRFLOW 2 3/16" TYP. AIRFLOW 7/16" TYP. F 3 1/4" G 1" TYP. 1 1/4" 2 7/8" 1" TYP. 7/16" TYP. (4 PLACES)* DOWNFLOW (FIELD CONVERTED) 2 3/16" TYP. 1 1/4" 3 1/4" UPFLOW (AS SHIPPED) 2 9/16" 5/16" 1 13/16" 1 5/8" 1 1/4" 5/16" 5/16" 1 13/16" TYP. 2 1/8" 1 1/4" F HORIZ. RIGHT (FIELD CONVERTED) 1/2" 7/8" 1/2" 7/8" HORIZ. LEFT (AS SHIPPED) 5" 1 5/8" 2 7/8" * HORIZONTAL MOUNT LOCATIONS - DIMPLES PROVIDED IN TOP PANEL, AND BACK OF CABINET. IN CABINET BOTTOM. HOLES PROVIDED A-COIL 1 13/16" TYP* AIRFLOW 2 3/16" TYP. AIRFLOW 7/16" TYP. (4 PLACES) F 4 3/4" 3 1/16" G 7/8" TYP* 1/2" TYP* 1 1/2" 5 7/8" 1 3/16" 7 7/8" HORIZ. LEFT (AS SHIPPED) 5/16" TYP* 1" TYP. (2 PLACES) 5/16" 1" TYP. 3" 1/8 7/16" TYP, (4 PLACES)* DOWNFLOW (FIELD CONVERTED) 1 13/16" TYP. 5 7/8" 7 7/8" 1 3/16" HORIZ. RIGHT (FIELD CONVERTED) 1 1/2" 1/2" 7/8" 2 3/16" TYP. UPFLOW (AS SHIPPED) 3 1/16" 4 3/4" 2 11/16" Fig. 2 - NF - English A

6 DIMENSIONS (cont.) SHIPPING WT SHIPPING WT COIL UNIT A B C D E F G H J (Kgs) (Kgs) CONFIGURATION SLOPE "A" NON TIN-COATED TIN-COATED NF X NF X NF X NF X NF X NF X NF X NOTE: 1. SERIES DESIGNATION IS THE 14TH POSITION OF UNIT PRODUCT NUMBER NOTE: ALLOW FROM FRONT FOR SERVICE 2. ALL DIMENSIONS ARE IN "MM" UNLESS NOTED. UNIT CONNECTION SIZES SUCTION: 018 & I.D. SWEAT 030 & I.D. SWEAT 042 THRU I.D. SWEAT LIQUID: 9.53 I.D. SWEAT CONDENSATE: 19.0 FPT OUTLET AIR 19.0 ALTERNATE DIA. K.O. FOR LOW VOLTAGE CONTROL WIRING A ALTERNATE 22.23, 27.78, DIA. K.O.'S FOR HIGH VOLTAGE POWER WIRING OPPOSITE SIDE OPTIONAL FIELD CONVERTED RIGHT SIDE RETURN OPENING (SLOPE COIL UNITS ONLY) NOTE: MODULAR UNITS WILL HAVE A TWO-PIECE CABINET , DIA. K.O.'S FOR HIGH VOLTAGE POWER WIRING TOP VIEW DIA. K.O. FOR LOW VOLTAGE CONTROL WIRING J H MAX FOR MODULAR UNITS B C DISCONNECT OR CIRCUIT BREAKER LOCATION BLOWER, CONTROL, & ELECTRIC HEATER ACCESS PANEL 31.8 OPENING RIGHT SIDE VIEW INLET AIR 63.5 COIL ACCESS PANEL INLET AIR 66.7 FITTING PANEL LIQUID LINE CONNECTION SUCTION LINE CONNECTION LIQUID LINE CONNECTION E LIQUID LINE CONNECTION SUCTION LINE CONNECTION OPENING FRONT VIEW SHOWN WITH "A" COIL DETAILS CONNECTION LOCATIONS FOR UPFLOW OR HORIZ. APPLICATIONS D INLET AIR FILTER ACCESS PANEL SLOPE COIL DETAILS CONNECTION LOCATIONS SHOWN FOR UPFLOW OR HORIZ. LEFT APPLICATIONS ACCESS PANEL CONFIG. FOR SLOPE COILS DOWNFLOW OR HORIZ. RIGHT APPLICATIONS AND "A" COILS DOWNFLOW APPLICATIONS Fig. 3 - NF - Metric A

7 DIMENSIONS (cont.) NOTES: 1. CONDENSATE PAN DRAIN CAPS NOT SHOWN FOR CLARITY. 2. ALL DIMENSIONS ARE IN "MM" UNLESS NOTED. AIRFLOW 55.6 TYP. SLOPE COIL AIRFLOW 11.1 TYP. F 82.6 G 25.4 TYP TYP TYP. (4 PLACES)* DOWNFLOW (FIELD CONVERTED) 55.6 TYP UPFLOW (AS SHIPPED) F HORIZ. RIGHT (FIELD CONVERTED) HORIZ. LEFT (AS SHIPPED) * HORIZONTAL MOUNT LOCATIONS - DIMPLES PROVIDED IN TOP PANEL, AND BACK OF CABINET. IN CABINET BOTTOM. HOLES PROVIDED 3.45 DIA. HORIZONTAL HANGING HARDWARE TO BE FIELD SUPPLIED. A-COIL 46.0 TYP* AIRFLOW 55.6 TYP. AIRFLOW 11.1 TYP. (4 PLACES) F G 22.2 TYP* TYP* HORIZ. LEFT (AS SHIPPED) 8.0 TYP* 25.4 TYP. (2 PLACES) TYP TYP, (4 PLACES)* DOWNFLOW (FIELD CONVERTED) 46.0 TYP HORIZ. RIGHT (FIELD CONVERTED) TYP. UPFLOW (AS SHIPPED) Fig. 4 - NF - Metric A

8 PHYSICAL DATA FACTORY ORDERING NO. INSTALLED HEAT (kw) NF018(0,T) NF018(0,T)05 5 NF018(0,T)08 8 NF024(0,T) NF024(0,T)05 5 NF024(0,T)10 10 NF030(0,T) NF030(0,T)08 8 NF030(0,T)10 10 NF036(0,T) NF036(0,T)10 10 NF036(0,T)15 15 NF042(0,T) NF042(0,T)10 10 NF042(0,T)15 15 NF048(0,T) NF048(0,T)10 10 NF048(0,T)15 15 NF060(0,T) NF060(0,T)15 15 NOMINAL COOLING CAPACITY (Btuh) 18,000 24,000 30,000 36,000 42,000 48,000 60,000 DIMENSIONS Height Width Depth /16 in. 1084mm /16 in. 1084mm /8 in. 1260mm /8 in. 1260mm /8 in. 1260mm /8 in. 1260mm /16 in. 1357mm /16 in. 363mm /16 in. 363mm /8 in. 447mm /8 in. 447mm /8 in. 536mm /8 in. 536mm /8 in. 536mm /16 in. 560mm /16 in. 560mm /16 in. 560mm /16 in. 560mm /16 in. 560mm /16 in. 560mm /16 in. 560mm SHIPPING WEIGHT 112 lb 51 kg 112 lb 51 kg 122 lb 55 kg 122 lb 55 kg 157 lb 71 kg 157 lb 71 kg 175 lb 79 kg SPECIFICATIONS EVAPORATOR COIL Face Area (sq. ft) Configuration Slope A Metering Device (Teflon --- ring piston) Puron Refrigerant EA52PT052 EA52PT057 EA52PT067 EA52PT070 EA52PT076 EA52PT080 TXV FILTER* /2 --- in (546 mm) X in (330 mm) /8 --- in (417 mm) /8 --- in (505 mm) BLOWER ASSEMBLY Blower Motor (X13) HD42AR225 HD44AR240 HD42AR226 HD44AR241 HD44AR242 HD46AR250 HD46AR251 HP 1/3 1/2 1/3 1/2 1/2 3/4 3/4 CFM *Filter must be field--- supplied for units. 8

9 PERFORMANCE DATA AIRFLOW PERFORMANCE (CFM) MODEL & SIZE BLOWER SPEED Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Tap Airflow outside 450 cfm/ton. NOTES: 1. Airflow based upon dry coil at 230v with factory--- approved filter and electric heater (2 element heater sizes 018 through 036, 3 element heater sizes 042 through 060). For models, airflow at 208 volts is approximately the same as 230 volts because the X13 motor is a constant torque motor. The torque doesn t drop off at the speeds the motor operates. 2. To avoid potential for condensate blowing out of drain pan prior to making drain trap: Return static pressure must be less than 0.40 in. wc. Horizontal applications of sizes must have supply static greater than 0.20 in. wc. 3. Airflow above 400 cfm/ton on size could result in condensate blowing off coil or splashing out of drain pan. 9

10 PERFORMANCE DATA (cont.) GROSS COOLING CAPACITIES (MBH) - PURONR REFRIGERANT INDOOR COIL SATURATED TEMPERATURE LEAVING EVAPORATOR (_F / C) AIR 35 / 2 40 / 4 45 / 7 50 / / 13 CFM EWB TC SHC BF TC SHC BF TC SHC BF TC SHC BF TC SHC BF 72 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / See Notes following table. UNIT SIZE

11 PERFORMANCE DATA (cont.) CFM --- Cubic Ft per Minute EWB --- Entering Wet Bulb _F (_C) LWB --- Leaving Wet Bulb _F (_C) TC --- Gross Cooling Capacity 1000 Btuh SHC --- Gross Sensible Capacity 1000 BF --- Bypass Factor MBH Btuh Btuh NOTES: 1. Contact manufacturer for cooling capacities at conditions other than shown in table. 2. Formulas: Leaving db = entering db -sensible heat cap x CFM Leaving wb = wb corresponding to enthalpy of air leaving coil (h lwb ) h lwb =h ewb -total capacity (Btuh) 4.5xCFM where h ewb = enthalpy of air entering coil. Direct interpolation is permissible. Do not extrapolate. 3. SHC is based on 80_F (27_C) db temperature of air entering coil. Below 80_F (27_C) db, subtract (Correction Factor x CFM) from SHC. Above 80_F (27_C) db, add (CorrectionFactorxCFM)toSHC. 4. Bypass Factor = 0 indicates no psychometric solution. Use bypass factor of next lower EWB for approximation. BYPASS FACTOR SHC CORRECTION FACTOR ENTERING AIR DRY-- BULB TEMPERATURE (_F) Under Over 85 ENTERING AIR DRY-- BULB TEMPERATURE (_C) Under Over 85 Correction Factor Use formula shown below Interpolation is permissible. Correction Factor = 1.09 x (1 --- BF) x (db ) AIR DELIVERY PERFORMANCE CORRECTION COMPONENT PRESSURE DROP (in wc) AT INDICATED AIRFLOW (DRY TO WET COIL) UNIT SIZE CFM ELECTRIC HEATER STATIC PRESSURE DROP (in wc) HEATER ELEMENTS kw EXTERNAL STATIC PRESSURE CORRECTION HEATER ELEMENTS kw EXTERNAL STATIC PRESSURE CORRECTION , , , , , , 24, The airflow performance data was developed using fan coils with 10---kW electric heaters (2 elements) in the 018 through 036 size units and 15---kW heaters (3 elements) in the 042 through 060 size units. For fan coils with heaters of a different number of elements, the external available static at a given CFM from the curve may be corrected by adding or subtracting available external static pressure as indicated above. MINIMUM CFM AND MOTOR SPEED SELECTION HEATER kw Speed Tap 4 (white wire) is used for electric heat only. White wire must remain on tap 4. 11

12 PERFORMANCE DATA (cont.) FIELD-INSTALLED FILTER STATIC PRESSURE DROP (in wc) CFM , , 042, ACCESSORY ELECTRIC HEATERS HEATER PART NO. 240V VOLTS/ PH STAGES (kw OPERATING) INTERNAL CIRCUIT PROTECTION FAN COIL SIZE USED WITH HEATING 230V KFCEH0401N /1 3 None ,400 KFCEH0501N /1 5 None ,700 KFCEH0801N /1 8 None ,100 KFCEH0901N /1 10 None ,400 KFCEH3201F /1 5, 20 Fuse} ,800 KFCEH /3 5, 15 None ,100 KFCEH /3 6, 12, 18 None ,500 KFCEH3401F /3* 8, 16, 24 Fuse 048, ,300 KFCEH3501F /3* 10, 20, 30 Fuse 048, ,100 KFCEH2401C /1 5 Circuit Breaker ,700 KFCEH2501C /1 8 Circuit Breaker ,100 KFCEH2601C /1 10 Circuit Breaker ,400 KFCEH3301C /1 5, 20 Circuit Breaker ,800 KFCEH2901N /1{ 3, 9 None ,200 KFCEH3001F /1 5, 15 Fuse} ,100 KFCEH3101C /1 5, 15 Circuit Breaker ,100 * Field convertible to 1 phase. { Field convertible to 3 phase. } Single point wiring kit required for these heaters in Canada. ** Blower Motor heat not included. ESTIMATED SOUND POWER LEVEL (dba) CONDITIONS OCTAVE BAND CENTER FREQUENCY* Ext Static CFM Pressure * Estimated sound power levels have been derived using the method described in the 1987 ASHRAE HVAC Systems & Applications Handbook, Chapter 52, p

13 PERFORMANCE DATA (cont.) ELECTRICAL DATA FOR UNITS WITH FACTORY-INSTALLED HEAT SINGLE CIRCUIT DUAL CIRCUIT MTR MTR VOLTS / PH/ HEAT PACK HTR. HTR. NF HP FLA HZ INSTALLED HEATER MCA MOCP MCA MOCP AMPS MCA MOCP AMPS AMPS L1/L2 L1/L2 L1/L2 L3/L4 L3/L4 L3/L4 018(0,T)05 1/ /230/1/60 MKFCEH0501N / / /30 N/A N/A N/A N/A N/A N/A 018(0,T)08 1/ /230/1/60 MKFCEH0801N / / /45 N/A N/A N/A N/A N/A N/A 024(0,T)05 1/ /230/1/60 MKFCEH0501N / / /30 N/A N/A N/A N/A N/A N/A 024(0,T)10 1/ /230/1/60 MKFCEH0901N / / /60 N/A N/A N/A N/A N/A N/A 030(0,T)08 1/ /230/1/60 MKFCEH0801N / / /45 N/A N/A N/A N/A N/A N/A 030(0,T)10 1/ /230/1/60 MKFCEH0901N / / /60 N/A N/A N/A N/A N/A N/A 036(0,T)10 1/ /230/1/60 MKFCEH0901N / / /60 N/A N/A N/A N/A N/A N/A 036(0,T)15 1/ /230/1/60 MKFCEH1501F / / / / / / / / /25 042(0,T)10 1/ /230/1/60 MKFCEH0901N / / /60 N/A N/A N/A N/A N/A N/A 042(0,T)15 1/ /230/1/60 MKFCEH1501F / / / / / / / / /25 048(0,T)10 3/ /230/1/60 MKFCEH0901N / / /60 N/A N/A N/A N/A N/A N/A 048(0,T)15 3/ /230/1/60 MKFCEH1501F / / / / / / / / /25 060(0,T)15 3/ /230/1/60 MKFCEH1501F / / / / / / / / /25 ELECTRICAL DATA FOR UNITS WITHOUT ELECTRICAL HEAT MODEL NO. SINGLE CIRCUIT BRANCH CIRCUIT MTR MTR VOLTS/PH/HZ MAXIMUM MIN WIRE SIZE* HP FLA MCA OVERCURRENT AWG PROTECTION NF018(0,T)00 1/ /230/1/ NF024(0,T)00 1/ /230/1/ NF030(0,T)00 1/ /230/1/ NF036(0,T)00 1/ /230/1/ NF042(0,T)00 1/ /230/1/ NF048(0,T)00 3/ /230/1/ NF060(0,T)00 3/ /230/1/ * Usecopperwireonly.Use75_C only in this application. When using non---metallic (NM) sheathed cable, wire size required should be based on that of 60_C conductors, instead of wire sizes shown in table above per NEC Article NOTE: If branch circuit wire length exceeds 100 ft (30 m), consult NEC to determine maximum wire length. Use 2% voltage drop. FLA --- Full Load Amps 13

14 ACCESSORY ELECTRIC HEATER ELECTRICAL DATA HEATER PART NO. kw P H A S E INTERNAL CIRCUIT PROTEC- TION Single Circuit HEATER AMPS 208/230V Dual Circuit Single Circuit Min Ampacity 208/230V* Dual Circuit Single Circuit Min Wire Size (AWG) 208/230V Dual Circuit BRANCH CIRCUIT Single Circuit Min Gnd Wire Size 208/230V Dual Circuit Max Fuse/Ckt Bkr Amps 208/230V Single Circuit Dual Circuit Single Circuit Max Wire Length 208/230V (Ft) 240v 208v L1,l2 L3,L4 L1,L2 L3,L4 L1, L2 L3, L4 L1, L2 L3,L4 L1,L2 L3,L4 L1,L2 L3,L4 Dual Circuit KFCEH0401N None 10.9/ / /12 12/12 20/20 67/68 KFCEH0501N None 18.1/ / /10 10/10 30/30 66/66 KFCEH0501N None 18.1/ /33.5 8/8 10/10 35/35 85/88 KFCEH2401C Ckt Bkr 18.1/ / /10 10/10 30/30 66/66 KFCEH2401C Ckt Bkr 18.1/ /33.5 8/8 10/10 35/35 85/88 KFCEH0801N None 28.9/ /48.5 8/8 10/10 45/50 59/60 KFCEH2501C Ckt Bkr 28.9/ /48.5 8/8 10/10 45/50 59/60 KFCEH2901N None 32.8/ /53.5 8/6 10/10 50/60 54/87 KFCEH2901N09** None 18.8/ /34.5 8/8 10/10 35/35 83/85 KFCEH0901N None 36.2/ /58.5 6/6 10/10 60/60 78/80 KFCEH2601C Ckt Bkr 36.2/ /58.5 6/6 10/10 60/60 78/80 KFCEH3001F Fuse 54.2/ / / / / /25.0 4/4 6/6 10/10 8/8 10/10 10/10 80/90 60/60 25/25 88/89 78/80 75/76 KFCEH3101C Ckt Bkr 36.2/ / / /25.0 6/6 10/10 10/10 10/10 60/60 25/25 78/80 75/76 KFCEH None 31.3/ /51.8 8/6 10/10 50/60 56/90 KFCEH None 37.6/ /60.4 6/6 10/8 60/70 76/77 KFCEH3201F Fuse 72.3/ / / / / /50.0 3/2 6/6 8/8 8/6 10/10 10/10 100/110 60/60 50/50 85/109 78/80 59/59 KFCEH3301C Ckt Bkr 36.2/ / / /50.0 6/6 8/8 10/10 10/10 60/60 50/50 78/80 59/59 KFCEH3401F Fuse 50.1/ /77.8 4/4 8/8 80/80 94/ Fuse 86.7/ / /1 6/6 125/ /116 KFCEH3501F Fuse 62.6/ /95.0 3/3 8/8 90/100 97/ Fuse 109.0/ / /00 6/6 150/ /150 FIELD MULTIPOINT WIRING OF 24 -AND 30 -kw SINGLE PHASE HEATER PART NO. kw P H A S E HEATER AMPS 208/230V MIN AMPACITY 208/230V* MIN WIRE SIZE (AWG) 208/230V MIN GND WIRE SIZE 208/230V MAX FUSE/CKT BKR AMPS 208/230V MAX WIRE LENGTH 208/230V (FT) 240V 208V L1,L2 L3,L4 L5,L6 L1,L2 L3,L4 L5,L6 L1,L2 L3,L4 L5,L6 L1,L2 L3,L4 L5,L6 L1,L2 L3,L4 L5,L6 KFCEH3401F / / / / / /40.0 8/8 8/8 8/8 10/10 45/50 40/40 40/40 59/60 73/73 73/73 KFCEH3501F / / / / / /50.0 6/6 8/8 8/8 10/10 60/60 50/50 50/50 78/80 59/59 59/59 * Includes blower motor amps of largest fan coil used with heater. { Copper wire must be used. If other than uncoated (non---plated), 75_C ambient, copper wire (solid wire for 10 AWG and smaller, stranded wire for larger than 10 AWG) is used, consult applicable tables of thenationalelectriccode(ansi/nfpa70). } Length shown is as measured 1 way along wire path between unit and service panel for a voltage drop not to exceed 2%. ** Field convertible to 3 phase. {{ Field convertible to 1 phase, single or multiple supply circuit. NOTES: 1. For fan coil sizes For fan coil sizes Single circuit application of F15 and F20 heaters requires single---point wiring kit accessory. 14

15 HEATER ELECTRICAL DATA FACTORY-INSTALLED HEATER OPTIONS* MODEL NF 5/8 5/10 8/10 10 / / / * For field--- installed heater/fan coil combinations, see Accessory Electric Heaters Table. ELECTRIC HEATER INTERNAL PROTECTION HEATER kw PHASE FUSE CKT BKR* QTY/SIZE QTY/SIZE 5 1 1/ /60 9 1/ / /30 2/60 2/ /60 2/ /3 6/ /3 6/60 * All circuit breakers are 2 pole. When using units with 20 -, 24 -, and 30 -kw electric heaters, maintain a 1 -in. (25mm) clearance from combustible materials to discharge plenum and ductwork and maintain a distance of 36 -in. (914mm) from the unit. Use an accessory downflow base to maintain proper clearance on downflow installations. Use flexible connectors between ductwork and unit to prevent transmission of vibration. When electric heater is installed, use heat resistant material for flexible connector between ductwork and unit at discharge connection. Ductwork passing through unconditioned space must be insulated and covered with vapor barrier ACCESSORIES ITEM ACCESSORY PART NO.* FAN COIL SIZE USED WITH 1. Disconnect Kit KFADK0201DSC Cooling controls and heaters 3--- through kw KFACB0101CFB 018, Downflow Base Kit KFACB0201CFB 030, 036 KFACB0301CFB 042, 048, Downflow Conversion Kit { KFADC0201SLP Slope Coil Units 018, 024, 030, 036 KFADC0401ACL A--- Coil Units 042, 048, Downflow/Horizontal Conversion Gasket Kit KFAHD0101SLP All 5. Horizontal Water Management Kit (25 pack) } KFAHC0125AAA All 6. Single--- Point Wiring Kit KFASP0101SPK Only with and kw Fused Heaters KFAFK0112SML 018, Filter Kit (12 Pack) KFAFK0212MED 030, 036 KFAFK0312LRG 042, 048, 060 FNCCABCC0014 (FILXXFNC0014) 018, Fan Coil Filter Cabinet FNCCABCC0017 (Fan Coil Filter Media) (FILXXFNC0017) 030, 036 FNCCABCC0021 (FILXXFNC0021) 042, 048, PVC Condensate Trap Kit (50 pack) KFAET0150ETK All 10. Air Cleaner volt Conversion Kit KEAVC All KSATX0201PUR 018, 024, TXV Kit Puron R A KSATX0301PUR 036, 042 KSATX0401PUR 048 KSATX0601HSO 018, 024, 030, 036, TXV Kit R KSATX0701HSO 048 KSATX1001HSO 060 * Factory authorized and listed, field---installed. { KFAHD0101SLP must also be purchased for downflow applications. } KFAHD0101SLP must also be purchased for downflow or horizontal applications. 15

16 ACCESSORIES (cont.) Accessory Kits Description Suggested and Required Use 1. Disconnect Kit The kit is used to disconnect electrical power to the fan coil so service or maintenance may be performed safely. SUGGESTED USE: Units for 3 - through 10 -kw electric resistance heaters and cooling controls. 2. Downflow Base Kit This kit is designed to provide a 1 -in. (25mm) minimum clearance between unit discharge plenum, ductwork, and combustible materials. It also provides a gap -free seal with the floor. REQUIRED USE: This kit must be used whenever fan coils are used in downflow applications. 3. Downflow Conversion Kit Fan coils are shipped from the factory for upflow or horizontal-left applications. Downflow conversion kits provide proper condensate water drainage and support for the coil when used in downflow applications. Separate kits are available for slope coils and A -coils. REQUIRED USE: This kit must be used whenever fan coils are used in downflow applications. 4. Downflow/Horizontal Conversion Gasket Kit This kit provides the proper gasketing of units when applied in either a downflow or horizontal application. REQUIRED USE: Fan coils in either downflow or horizontal applications. 5. Horizontal Applications - Water Management Kit This kit provides proper installation of fan coils under conditions of high static pressure and high relative humidity. SUGGESTED USE: All fan coils. 6. Single Point Wiring Kit The single point wiring kit acts as a jumper between L1 and L3 lugs, and between the L2 and L4 lugs. This allows the installer to run two heavy -gauge, high -voltage wires into the fan coil rather than 4 light-gauge, high -voltage wires. SUGGESTED USE: Fan coils with 15 - and 20 -kw fused heaters only. 7. Filter Kit (12 pack) The kit consists of 12 fan coil framed filters. These filters collect large dust particles from the return air entering the fan coil and prevents them from collecting on the coil. This process helps to keep the coil clean, which increases heat transfer and, in turn, the efficiency of the system. SUGGESTED USE: To replace filters in fan coils. REQUIRED USE: All units unless a filter grille is used. 8. Fan Coil Filter Cabinet This cabinet is mounted to the fan coil on the return air end and designed to slip over the outer fan coil casing. The cabinets are insulated using the same insulation as production fan coils. They are designed for the removal of particulates from indoor air using FILXXFNC00(14, 17, 21, 24) media filter cartridges. These fan coil media filter cartridge kits are designed for the removal of particles from indoor air. The cartridge is installed in the return air duct next to the air handler or further upstream. SUGGESTED USE: All fan coils. 9. Condensate Drain Trap Kit This kit consists of 50 PVC condensate traps. Each trap is pre-formed and ready for field installation. This deep trap helps the system make and hold proper condensate flow even during blower initiation. SUGGESTED USE: All fan coils. 10. Air Cleaner 240 -volt Conversion Kit The AIRA electronic air cleaner comes ready for 115 -v operation. REQUIRED USE: This kit is required when running 240 -volt circuit to air cleaner. Copyright 2010 Carrier Corp. S 7310 W. Morris St. S Indianapolis, IN Printed in U.S.A. Edition Date: 05/10 Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. Catalog No: NF---04PD Replaces: NF ---03PD 16