ICB VEGETABLE SLICER Model HLC-300 User and Maintenance Manual

Transcription

1 ICB VEGETABLE SLICER Model HLC-300 User and Maintenance Manual - 1 -

2 1. SAFETY INFORMATION 1.1. GENERAL PRECAUTIONS Become familiar with the instructions for use and safety information contained in this manual. Avoid placing hands near the cutting discs and moving parts. Disconnect from mains power before cleaning and maintenance. Periodically inspect the AC power cord and electric elements for wear or damage. Do not use the slicer for frozen food. The unit must be serviced by qualified technicians MECHANICAL SAFETY The vegetable slicer described in this manual meets mechanical safety requirements per GB ELECTRICAL SAFETY Electrical safety of this unit complies with CENELEC GB Security micro-switches are mounted on the machine to stop operation when the cover is opened to gain access to the cutting discs. SETTING N.2 MICROSWITCHES This unit can be used in humid environments due to a re-start relay in the low voltage circuit, well insulated electrical elements, and treated aluminum finish. 2. TECHNICAL FEATURES The smooth-edged aluminum and magnesium alloy design of the slicer allows for safe, easy cleaning and maintenance TABLE OF WEIGHT AND MEASURES MODEL DIMENSIONS WEIGHT POWER ELECTRICAL REVS CM. KG. WATT CONNECTION DISC HLC X23X /1/ PACKAGING The slicer is packed in a sturdy cardboard box with internal molded insulation to protect the unit during transport. Included in the box: HLC-300 Vegetable Slicer User and Maintenance Manual High ejecting disc and low ejecting disc - 2 -

3 3. INSTALLATION 3.1. PLACEMENT Warning: The unit location must comply with electrical regulations and general safety of use. The manufacturer declines any and all responsibility for direct or indirect damages which may ensue for non-compliance with the above mentioned regulations. Set the slicer on a wide, level, dry and solid surface away from heat sources and water spray ELECTRIC CONNECTIONS The unit must be properly grounded when connected to AC mains supply. The manufacturer declines any and all responsibility for direct and indirect damages which may ensue for non-compliance with the regulations in force. The slicer is designed to operate with single-phase 110v/1/60 hz. Confirm that the direction of rotation of the central shaft is counter-clockwise: open the cover, rotate the side handle and remove the cutting disc (if any) with idle machine, (or with the white plastic ejector only), through the upper (round) opening, and by pressing once the start green button followed by stop red button. CONFIRM THE DIRECTION OF ROTATION 3.3. SAFETY MEASURES AND USER TRAINING Ensue that any users are familiar with the operational and safety aspects of this unit as described in this manual CONTROLS 4. USE OF THE EQUIPMENT The controls and pilot light are located on the right side of the base. 1. Green button starts the machine 2. Red button for stops the machine - 3 -

4 4.2. SETTING THE DISCS IN THE MACHINE Rotate the knob as shown in figure 1 below and open the cover. First place the plastic ejecting disc (figure 2), then the selected cutting disc. Close the cover and reverse the rotation of the handle. Press on the start button to automatically hook the discs in the correct position. COVER OPENING (Figure 1) DISC POSITION (Figure 2) 4.3. SLICING FOOD Lift the handle and place the food inside the opening as shown in figure 3, then close the handle. Press the green start button with your right hand, and with your left hand, lightly move the handle downwards until food is fully used up. (Figure 3) Lift the handle to introduce other food. The machine starts automatically when the handle is closed. Repeat these operations until the food is fully used up. It is possible to use the two openings with a single disc; when two discs are used for cutting sticks and match-like food, the inlet opening set over the grid must be used The smaller round opening is used to slit vegetables such as carrots, vegetable marrow, etc. Warning: never use your hands to press the vegetables into the machine, always use the pestle supplied RELEASE AND REPLACEMENT OF THE DISCS Turn the knurled handle and lift the cover. (figure 1) Turn the disc counterclockwise and cover the cutting edge with appropriate material (rubber, fabric, etc), then lift it by setting your hand under the disc. Simply lift the discs to remove the grid disc for dice cutting, or the disc for stick cutting with the plastic disc. (figures 4-5). (Figure 4) (Figure 5) - 4 -

5 5. CLEANING AND MAINTENANCE OPERATIONS 5.1. GENERALITIES AND PRODUCTS FOR CLEANING Before carrying out any cleaning or maintenance operations, ensure that the mains switch is off and the supply plug is disconnected from the mains. Clean the equipment and the discs every day for optimal operation and life of the equipment. The discs, the grid for cutting dices, and the plastic ejector, can be removed and washed under a warm water jet. Clean the machine and the disc positions with a cloth or a sponge wet with warm water, remove all debris to ensure the discs seat properly. Open the cover and loosen the 2 pins as shown in figure 6. Remove the cover and wash under a water jet. (Figure 6) Clean the surfaces with soap and water, alcohol, detergents without abrasives or substances based on chlorine or soda (chlorine water, muriatic acid). Never use abrasives, steel wool, or similar products as they may damage the finish and compromise product life FAILURE TO START When the white pilot light on the panel in on, but the machine does not start, check to ensure that the handle and the cover are closed. In the closed position, both the safety micro-switches are on; these safety micro-switches prevent the unit from starting in unsafe conditions. In the case of unit failure, the unit should only be serviced by qualified personnel LONG TERM STORAGE For long term storage, disconnect the main wall switch and clean the machine and its accessories. Use white vaseline oil (or similar products) to protect all the machine s elements. These products, mainly made up of oily and detergent substances, and now available in spray cylinders for easy application, preserve the glossy finish of the aluminum magnesium alloy, and prevent corrosion. It is recommended to cover the machine with a nylon (or similar) cloth. ILLUSTRATIONS 110V - 5 -

6 - 6 -