User Manual for AirFlow Convection Oven

Transcription

1 User Manual for AirFlow Convection Oven KEL-1100 IFU: OV /02/2015 Tel Fax

2 Table of contents: Page 3 Page 3 Page 4 Page 5-6 Page 6-8 Page 9 Page 10 Page 10 Page 10 Important Safety Instructions Electrical Connections Restrictions for Use Oven Operation Cleaning the Oven Repair Warranty EC-Conformity Declaration Technical Specifications Page 2

3 1 Important Safety Instructions Read all instructions carefully before installing or using this device for the first time. The system must be completely cooled to room temperature prior to system set-up or breakdown. 2 Electrical Connection ELECTRICAL CONNECTION Connection to the electrical power source must be done according to all state and local codes. Before connecting your oven, make sure that the voltage and the amps comply with those stated on the data plate. Avoid using patch cords and multiple jacks. The appliance must be placed so the connection plug to the outlet can be easily reached. When the appliance is in operation, the power supply voltage must not diverge from the value of the nominal voltage, written on the technical data plate, by more than + or 10%. Ovens are equipped with cordset and NEMA plug (single phase; 120V or V, depending on oven model.) It is sufficient to insert the plug in the proper outlet (the outlet must be suitable for the plug assembled on the oven.) Page 3

4 3 Restrictions for Use This unit has been constructed for indoor use only. It must be only in a clean, dry environment. It is not recommended to place any items on or against this unit when in use. Although properly insulated, the surface could become moderately hot during use. Do not place objects or items on top of the convection oven at any time. Keep this user guide, or a copy near the unit, for easy reference when needed. Do not situate the oven directly against a back wall, as the back side of the oven becomes hot during use. Be sure there is adequate space for the door to be opened completely. Do not use a steam cleaner to clean this appliance. Pressurized steam could penetrate electrical components and cause a short circuit. Do not use plastic containers or plastic wraps in the oven, unless this material has been tested and approved for this purpose. Some plastics may melt and cause damage to the oven. Do not use sharp objects to remove dirt / debris from the racks. These racks have a non-stick coating that can be damaged by sharp objects or abrasive cleaning. Page 4

5 4 Oven Operation Digital Controls Initial Start 1. After the oven is plugged in, press the START button (#9). 2. Press the SELECT button (#7) so the light by the temperature symbol is lit (#5). 3. For Klarity masks, press the (-) button (#8) and set the temperature for 165 degrees. For other brands of masks, refer to their instruction sheet or call the company for further instructions. 4. Press SELECT again, so the light by the clock symbol (#4) is lit. This is the timer. 5. Press the (-) button (#8) and set the timer to INF. This will allow the oven to continuously run. (The timer can be used, however once the timer goes off, the OVEN WILL SHUT OFF. We recommend a digital kitchen timer be used if you want to keep the oven warm by running it at all times.) 6. Check the STEP button (#1). Make sure the light beside setting #1 is lit. 7. Press START (#9). It will take 5-6 minutes for the oven to reach the set temperature. To view the temperature reading, touch the SELECT button again. 8. Follow instruction sheets included with your masks for heating times and usage information. For Klarity masks, heat up time is 3-4 minutes and the cushion heat up time is minutes. Turning the Oven Off 1. Press the START button (#9) and hold until the oven beeps for a duration of a few seconds. 2. The oven, when left undisturbed, will then shut itself off in minutes. Page 5

6 Manual Controls Start 1. Line up the red line on the temperature dial to the notch on the oven case. This will allow the inside temperature to reach the desired 165 degrees. *please note, the inside temperature will vary. Adjust the dial as needed to keep the desired temperature. 2. Turn the timer dial counterclockwise so the notch on the oven case lines up with the hand symbol. This sets the oven to run continuously. Turning the Oven Off 1. Turn the timer dial clockwise and line up the notch of the oven case with the 0. You will hear a lengthy series of loud beeps, signifying that the oven is off. 5 Cleaning the Oven Clean the appliance with a solution of warm water and liquid soap applied with a soft sponge. Dry with a soft cloth. Caution do not clean the display with water, only with a dry soft cloth. Do not use a steam cleaner to clean this appliance. Pressurized steam could penetrate electrical components and cause a short circuit. CLEANING THE OVEN WARNING: Before starting any maintenance or cleaning operation, it is necessary to disconnectthe electrical power supply and wait for your oven to cool down. Never wash the cooking chamber with acids, abrasives, or aggressive detergents. CLEANING THE COOKING CAVITY Make sure to wipe up any and all spills as they occur. At the end of the day (or as needed), clean the cavity using only proper products. Never clean the stainless steel with acids, caustic detergents, abrasives or any products containing chlorine. CLEANING THE OUTSIDE OF YOUR OVEN Wipe up spills, as they occur, with a damp cloth. Warm water and a mild detergent can be used. Rinse and dry completely. Never use a spray of water to clean the outside of your oven. This may damage the electrical components and void your warranty. Page 6

7 CLEANING THE OVEN DOOR GLASS 1. Open oven door and remove inner door glass using the following directions. (Glass holder tabs on left & right sides of door keep inner door glass in place.) 2. With oven door opened completely, use fingers to pull left and right glass holder tabs forward until fully extended and the corner of the door glass is visible. 3. Using fingers to hold glass holder tabs open, position thumbs under the inner door glass and push glass up until it just clears the glass holder tabs. Release glass holder tabs while supporting the door glass with thumbs. Page 7

8 4. Grasp both sides of the glass firmly and pull the glass toward you until it clears the door glass slots at the bottom of the door. (Be careful to support the glass when pulling it toward you, to avoid the back edge of the glass dropping onto the outer door glass below it.) Lift the glass and place gently on countertop. 5. Clean the door glass, using a soft cloth moderately dampened with soap and water or glass cleaner. Rinse glass and dry it completely. 6. Position cleaned inner door glass over the open oven door so that the oval logo on the glass is facing down in the left back corner. Slide the back edge of the door glass into the door glass slots at the bottom of the door. 7. Lower the glass until it is resting on the glass holder tabs. 8. Pull the glass holder tabs forward until the glass drops into place in the door. Then release the glass holder tabs to hold the glass in place. Page 8

9 6 Repair Should a defective unit need repair the cleaned unit must be shipped to the USA distributor, Klarity Medical Products, LLC. The full delivery address can be found below. A detailed description of the type of problem or defect must be included. These ovens may also display an error code if something is wrong. Please let us know the code when contacting us for repairs. Contact Klarity Medical Products, LLC to receive a Returns Authorization Number before returning the item. Shipping Address: Klarity Medical Products, LLC Do not try to perform any repair(s) on the unit during warranty period. Caution: A qualified technician should only perform repairs. Repairs and service by unqualified persons could cause injury or appliance damage, as well as voiding the warranty. Allow the appliance to cool before repairing the unit. Page 9

10 7 Warranty This product has a full warranty of 12 months from shipment date. This warranty is valid on the condition that the unit has been used following the above listed guidelines only. Klarity Medical Products is entitled to refuse a warranty repair if it can be proved that the unit has been operated against the guidelines listed in this document. It is highly recommended to keep the original package material during the entire warranty period. Repair during the warranty period is only valid if the unit is shipped in the original box. The warranty does not include shipment costs between the user and Klarity Medical Products, LLC. Klarity Medical Products, LLC is entitled to decide if the unit can be properly repaired. If the unit is beyond repair, it will be replaced with a new unit. 8 EC-conformity Declaration The EC-Conformity Declaration is provided as a separate document. The declaration is the full responsibility of Klarity Medical Products, LLC. Any questions or disputes connected to the declaration must be made to Klarity Medical Products, LLC. 9 Technical Specifications Finish: Glass Front with Stainless Steel Cover Minimum Temperature: 65C / 150F Maximum Temperature: 260C / 500F Outside dimensions: 31.5 x17 x30.5 (80cm x 43cm x 77cm) Weight : 88 LBS Page 10