Silhouette. Feedwater Heater. Boiler Feedwater
|
|
- Charlene Lucas
- 6 years ago
- Views:
Transcription
1 Roth Roth Low Low Silhouette Silhouette TRAY DEAERATORS Boiler Boiler Feedwater Feedwater Heater Heater Capacities Capacities to to 50,000 50,000 lb/hr lb/hr Model RDTV vertical tray type deaerator The Roth Solution: Preheated, deaerated conditioned water reduces operating cost. Roth deaerators are assembled with Roth pumps requiring only one- or two-foot NPSH operating at 1750 rpm Roth Pump Company ROTH
2 Reduce costs and improve system efficiency by preheating and deaerating boiler feedwater Roth tray type deaerators condition feedwater to 0% CO 2 and only.005 cc/l of oxygen Why deaerate boiler feedwater? There are many advantages to deaerating water prior to boiler input, but they all boil down to reduced cost operation. Water is heated during deaeration to near the temperature of the boiler water, thus minimizing the risk of thermal shock damage to a high-value boiler system. The deaerating process removes noncondensable gases (oxygen and carbon dioxide) which tend to act as insulators inhibiting the transfer of heat within the boiler. Removal of oxygen and carbon dioxide reduces corrosion within the boiler and piping, extending the life expectancy of the system and reducing maintenance cost. Higher temperature feedwater reduces the chance of pressure drop within the boiler which can occur when cold water is added. Recycling of steam from vents and flash steam from traps that would otherwise be vented to the atmosphere can result in appreciable energy savings. Mechanical deaeration by a feedwater deaerator can cut the amount of chemical consumables used for water conditioning for a continuing operating cost saving. Choosing the right deaerator Roth tray type deaerators are generally considered the superior choice for most applications. These units use stainless steel for all internal surfaces which come in contact with undeaerated water. Residence time for undeaerated water inside a tray type deaerator is longer, providing more efficient deaeration, particularly where wide load swings occur. A large diameter hinged door affords easy access to internal trays and spray tubes for maintenance and replacement. Although tray type deaerators require a larger initial investment, the benefits in efficiency and reduced cost of maintenance tend to pay for themselves quickly. Pump selection Roth deaerators use low NPSH pumps. Most pumps selected require only one foot NPSH operating at 1750 rpm. By using these pumps, the overall height of the unit can be lowered. This can save on construction cost.
3 Roth Deaerator Specifications Control and piping configurations will vary depending upon job specifications and conditions. Dimensions are subject to change without notice. Consult factory for certified dimensions. Legend for drawings 1. Make-up water control 2. High level control 3. Low level control 4. Vacuum breaker 5. Temperature gauge 6. Pressure gauge 7. 1½ NPT vent 8. 1 NPT chemical port 9. 1 NPT drain NPT sample port NPT additional port 12. Gauge glass Model * = # of RDTV- RDTV- RDTV- RDTV- RDTV- RDTV- RDTV- RDTV- RDTV- RDTVpumps * * * * * * * * * * Capacity Lb/h 5,000 10,000 15,000 20,000 25,000 30,000 35,000 40,000 45,000 50,000 (kg/h) (2,268) (4,536) (6,804) (9,072) (11,340) (13,608) (15,876) (18,144) (20,412) (22,680) Boiler hp ,015 1,160 1,305 1,450 (kw) (1,422) (2,844) (4,267) (5,686) (7,107) (8,529) (9,950) (11,372) (12,793) (14,214) Storage ,000 gallons (l) (378) (757) (1,135) (1,514) (1,893) (2,271) (2,650) (3,028) (3,407) (3,785) Dimensions A. Overall in (cm) length (168) (168) (168) (213) (213) (213) (244) (244) (244) (244) except as B. Overall noted width (137) (137) (137) (183) (183) (183) (213) (213) (213) (213) C. Overall height (211) (251) (287) (274) (295) (315) (318) (333) (358) (373) D. Tank diameter (107) (107) (107) (152) (152) (152) (183) (183) (183) (183) E. Overflow 3, 150 lb 3, 150 lb 3, 150 lb 3, 150 lb 3, 150 lb 3, 150 lb 3, 150 lb 2 NPT 2 NPT 2 NPT trap flange flange flange flange flange flange flange F. Tray access door dia. (51) (51) (51) (61) (61) (61) (61) (61) (61) (61) G. Pump 3, 150 lb 3, 150 lb 3, 150 lb 4, 150 lb 4, 150 lb 4, 150 lb 6, 150 lb 6, 150 lb 6, 150 lb 6, 150 lb suction flange flange flange flange flange flange flange flange flange flange H. Pump bypass 2 NPT 2 NPT 2 NPT 2 NPT 2 NPT 2 NPT 3 NPT 3 NPT 3 NPT 3 NPT I. Hi-temp condensate 2, 150 lb 2, 150 lb 2, 150 lb 3, 150 lb 3, 150 lb 3, 150 lb 3, 150 lb 3, 150 lb 3, 150 lb 3, 150 lb return flange flange flange flange flange flange flange flange flange flange J. Steam 4, 150 lb 4, 150 lb 4, 150 lb 6, 150 lb 6, 150 lb 6, 150 lb 8, 150 lb 8, 150 lb 8, 150 lb 8, 150 lb connection flange flange flange flange flange flange flange flange flange flange K. Water 2, 150 lb 2, 150 lb 2, 150 lb 3, 150 lb 3, 150 lb 3, 150 lb 4, 150 lb 4, 150 lb 4, 150 lb 4, 150 lb connection flange flange flange flange flange flange flange flange flange flange L. Base height (10) (10) (10) (10) (10) (10) (10) (10) (10) (10)
4 Sample Specification Roth Deaerator DEAERATOR: A. The deaerator shall be a Roth style RDTV deaerator which guarantees oxygen removal to cc/l (7 ppb) or less and carbon dioxide removal to a zero measurable level in the effluent throughout all load conditions between 0% and 100% of rated capacity. The deaeration process will take place in a 5-15 psig steam environment that will heat the water to F requiring a pressurized vessel. The deaerator shall be manufactured in strict accordance with the ASME Section VIII, Div. 1 code and bear the ASME stamp for a maximum working pressure of 50 psig at 300ºF. An atmospheric deaerator is not acceptable. A minimum of 1/16 corrosion allowance shall be added to the ASME calculated material thickness for heads and shell and will be noted on the ASME data report (form U-1). The deaerator is to be of the vertical design with a vessel of diameter x high setting less than 18 from the floor. B. The deaerator is to be of the tray type design. Spray type deaerators are not acceptable. Flow of steam shall be such that the steam entering the heater first comes in contact with the hottest water which is leaving the last row of trays and then proceeds upward through the tray stack in a counter-flow fashion. The water to be deaerated will enter the vessel through a stainless steel spray tube. The spray tube will disperse water into a 304L stainless steel box that is sealed so that escaping gasses can not come in contact with the vessel walls. The gases escape through a 304L vent condenser pipe on top of the tray box that extends out the top of the vessel. The spray tube directs the water into sections of a 304L stainless steel vent welded on top of the tray box. The water falls downward from the vent condenser and spreads over the stainless steel trays and, after deaeration, falls into the storage area. The stainless steel (304L) trays will be removable through a minimum 20 dia. hinged tray access door. Each tray shall weigh no more than 30 lbs. for easy handling and inspection and shall be of welded construction. Rivets are not acceptable. The deaerator will be designed so that undeaerated water will only come into contact with stainless steel components. C. The tray type deaerator is to be fully trimmed by the manufacturer including the following items: 1. Low Level Control: An external float type control is to be supplied to monitor a low level condition. A low level shall ring an alarm bell and light a red light on the control panel notifying the operator. The control shall also shut off the deaerator pumps protecting them from harm. 2. High Level Control: An external float type control is to be supplied to monitor a high level condition. A high level shall ring an alarm bell and light a red light on the control panel notifying the operator. The high level control shall be activated before the water reaches the overflow level. 3. Overflow Trap: A mechanical self-contained external float type overflow trap shall be supplied to overflow the water in the storage area before flooding the deaerator. The overflow trap body is to be constructed of cast iron. Inside the body, a stainless steel ball float automatically operates a double-seated brass valve. The cast iron body is to be bolted together in order to take apart for inspection/maintenance of the valve assembly. A butterfly valve is to be supplied between the deaerator and the trap for inspection without having to shut down the deaerator. 4. Make-up Water Assembly: An electric water level controller and make-up water valve is to be supplied to monitor the level of water storage in the deaerator and add make-up water when necessary for continued operation. The level to activate the water valve shall be field adjustable to match desirable operating conditions. The water valve shall be suitable for operation with a pressure differential of up to 150 psi. The valve shall default to a closed position when deenergized and be a modulating or slow closing valve in order to reduce or eliminate water hammer. The valve shall be factory piped with a 3-valve bypass assembly and strainer. 5. Pressure Reducing Valve: A self-contained pilot operated valve shall be supplied when necessary to reduce the available steam pressure to the operating pressure of the deaerator (5-15 psig). The valve is to be shipped loose for field installation. Relief valve(s) acceptable for ASME service shall also be supplied. The relieving capacity of the valves shall be greater than the maximum capacity of the pressure reducing valve and set to relieve at 50 psig. 6. Vacuum Breaker: A vacuum breaker is to be supplied to release any vacuum in the deaerator during operation. 7. Vent Valve: A manual valve shall be supplied to vent the deaerator. The valve is to have the ability to be field adjustable with a 1/8 drilled orifice to avoid complete shut off capability. 8. Drain Valve: A gate valve is to be supplied and sized the same diameter as the drain connection and be supplied by the manufacturer. 9. Misc. Gauges: A pressure and temperature gauge shall be supplied and installed by the manufacturer. The gauges shall be sized suitable for the operation and design range of the deaerator and follow any ASME or local codes and requirements. A gauge glass shall be supplied and installed to cover the water level range from low level to overflow level. The gauge glass shall be protected from getting hit by outside objects and be so mounted to protect from getting broken. 10. Pump Suction: The pump suction shall be sized based on a velocity 3 ft/sec of twice the deaerator capacity. A separate gate valve, strainer, and flexible connector shall be supplied for each pump.
5 Roth Tray Type Deaerators Roth Deaerator Pumps Roth tray type deaerators remove CO 2 from feedwater completely and reduce oxygen to.005 cc/l. Available with capacities up to 50,000 pounds per hour, Roth tray type deaerators come completely packaged with all standard accessories and trim. Internal surfaces which come in contact with undeaerated water are stainless steel. Undeaerated water and corrosive gases never come in contact with the deaerator shell. A complete line of boiler feed pumps and control panel packages is available. Custom engineered systems and larger than standard units are also available. Consult the factory. Non-condensable gases (O 2, CO 2 ) Deaerated water Condensate return & water make-up Steam Roth pioneering The Roy E. Roth Company has been a pioneer in the industry for over 45 years by developing NPSH data on its products for use by engineers. In 1954, it was the first manufacturer of regenerative turbine pumps to publish NPSH data on individual models. At that time, the Roy E. Roth Company developed and published the first NPSH curves on regenerative turbine pumps in a format now used throughout the industry. It is the only manufacturer of regenerative turbine pumps today with numerous patents designed to improve the NPSH characteristics of its pumps. Roth one-foot NPSH pumps The Roth Pump Company, the manufacturing successor, is the only pump manufacturer in the world today that offers a line of pumps with full performance at one-foot NPSH at speeds of both 1750 and 3500 rpm in a range of differential heads up to 600 feet TDH and capacities up to 190 GPM. All Roth pumps in this bulletin are guaranteed to deliver the full-rated capacity of water to the boiler. Roth one-foot NPSH pumps were originally developed to pump 230 F deaerated water from the deaerator to the boiler. Now the original design has been improved to include high-capacity models fully functional at one-foot NPSH. Standard equipment All deaerators are constructed to ASME Section VIII, Div. 1 for 50 psig, 300 F Easily accessible manways and access doors for internal inspection and servicing Standard storage capacity: 10 minutes of operation. Optional larger storage capacities available Structural steel stand and pump platform High and low level control alarms External make-up water level control (field adjustable) Make-up water valve with three-valve bypass Pilot operated steam pressure reducing valve (when required) Relief valve sized for full output of the pressure reducing valve set at 50 psig Manual vent valve(s) with properly sized orifice in gate Vacuum breaker Pressure gauge and thermometer Overflow trap sized to relieve full capacity of deaerator Full range sight glass Drain valve
6 Roth Pump Company P.O. Box 4330, Rock Island, IL U.S.A. Toll-Free: ROTH ( ) Fax: Contact your Authorized Roth Representative Today! , Roth Pump Company Printed in USA
Moss MOSS TRAY DEAERATOR ECONOMICAL INDUSTRIAL DEAERATOR SYSTEMS
Moss MOSS TRAY DEAERATOR ECONOMICAL INDUSTRIAL DEAERATOR SYSTEMS MOSS TRAY DEAERATOR DESIGNS WHY DEAERATE? Removal of corrosive oxygen and carbon dioxide from boiler feedwater Reduction in the use of oxygen
More information100 years of boiler technology leadership.
100 years of boiler technology leadership. TM A subsidiary of Burnham Holdings Compact Boiler Feed Systems Capacities from 20 to 80 boiler HP 15 through 150 PSI boilers The Bryan compact boiler feed system
More informationPUMPS & PUMPING SYSTEMS FOR THE CHEMICAL PROCESSING & HEATING & AIR CONDITIONING INDUSTRY
PUMPS & PUMPING SYSTEMS FOR THE CHEMICAL PROCESSING & HEATING & AIR CONDITIONING INDUSTRY THE ROTH SOLUTION PROVIDES: Lowest NPSHr - Lower Motor Speeds Lower Tank Heights - Reduced Maintenance ROTH PUMP
More informationTray ST5. Tray Type Deaerator Pressurized.005 cc/liter. industrialsteam.com
Tray ST5 Pressurized and Atmospheric Deaerators Tray Type Deaerator Pressurized.005 cc/liter COUNTER FLOW TRAY design provides guaranteed removal of all dissolved oxygen in excess of.005 cc/liter from
More informationDeaerator. Specifications
ESI, INC. OF TENNESSEE RENTAL EQUIPMENT Deaerator Description The deaerator, built in 1996, is a spray-type deaerating feedwater heater and storage tank with stainless steel internals. The deaerator is
More informationSpray Flow II cc/liter Atmospheric Deaerator. industrialsteam.com
Spray Flow II Pressurized and Atmospheric Deaerators.005 cc/liter Atmospheric Deaerator CONSTANT RECYCLING guarantees deaeration of all dissolved oxygen in excess of.005 cc/liter from 0% to 100% of deaerator
More informationSpray Flow II cc/liter Atmospheric Deaerator. industrialsteam.com
Spray Flow II.00 cc/liter Atmospheric Deaerator Pressurized and Atmospheric Deaerators CONSTANT RECYCLING guarantees deaeration of all dissolved oxygen in excess of.00 cc/liter from 0% to 100% of deaerator
More information.03 ATMOSPHERIC DEAERATOR
.03 ATMOSPHERIC DEAERATOR SPECIFICATION SHEET NO. 3200 OCTOBER 1, 2007 GENERAL DESCRIPTION The Sellers atmospheric.03 deaerators condition make-up water and condensate returns to convert them into more
More informationTYPE.005 DA-STP TYPE.005 DA-STP-2T. Spray Tray Deaerating Pressurized Boiler Feed Pumps. and. when separate surge tank is utilized
SHIPPENSBURG PUMP CO., INC. P.O. BOX 279, SHIPPENSBURG, PA 17257 PHONE 717-532-7321 FAX 717-532-7704 WWW.SHIPCOPUMPS.COM BULLETIN 147 Revised 7/09 TYPE.005 DA-STP Spray Tray Deaerating Pressurized Boiler
More information.005 ATMOSPHERIC DEAERATOR
.005 ATMOSPHERIC DEAERATOR OCTOBER 1, 2007 GENERAL DESCRIPTION The Sellers atmospheric.005 deaerators condition make-up water and condensate returns to convert them into more desirable boiler feedwater.
More informationBuildingName The Description of the Project P DOCUMENTS
ARCHITECTURE, ENGINEERING AND CONSTRUCTION P00000000 0000 DOCUMENTS ARCHITECTURE & ENGINEERING 326 East Hoover, Mail Stop B Ann Arbor, MI 48109-1002 Phone: 734-764-3414 Fax: 734-936-3334 SPECIFICATION
More informationDEAERATORS .005 ATMOSPHERIC DEAERATOR
918 W WALNUT ST, DANVILLE, KENTUCKY 40422-0048 PHONE (859) 236-3181 www.sellersmfg.com SPECIFICATION SHEET NO. 3300 DEAERATORS.005 ATMOSPHERIC DEAERATOR GENERAL DESCRIPTION The Sellers atmospheric.005
More informationCondensate Return Feedwater Systems For Low and High Pressure Steam Boilers
For Low and High Pressure Steam Boilers Rite s feedwater return systems are engineered for the safe and efficient storage and pumping of condensate and make-up water back to the boiler. Why Rite? Because
More informationInstallation and Operating Service Manual
Installation and Operating Service Manual SPRAY-TYPE DEAERATOR Bryan Steam LLC, 783 N. Chili Avenue, Peru, IN 46970, Phone 765.473.6651, Fax 765.473.3074 www.bryanboilers.com Form 2141 Revision Date 5/1/2015
More informationSECTION HEATING BOILER FEEDWATER EQUIPMENT
SECTION 23 53 00 HEATING BOILER FEEDWATER EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section includes boiler feedwater pumps, de-aerators, accessories, controls and tanks. 1.2 REFERENCES A. ASME (American
More informationTitle: YALE OFFICE OF FACILITIES PROCEDURE MANUAL Chapter: 01 - Yale Design Standard Division: HVAC Standards
Date Description of Change Pages / Sections Modified ID 6/15/16 Entire document - mgl44 PART 1 - INTRODUCTION 1.1 PURPOSE A. This section is intended to define the general installation and minimum product
More informationBoiler Condensate Return Basics. Presented by Steve Connor February 24, 2016
Boiler Condensate Return Basics Presented by Steve Connor February 24, 2016 What We Are Covering Today? Brief review of the total steam system Why a proper condensate return system is so important Condensate
More information/ / Take the technological step into MODERN Condensate Handling Equipment for steam systems MANUFACTURED IN AMERICA with craftsmanship and quality.
Take the technological step into MODERN Condensate Handling Equipment for steam systems MANUFACTURED IN AMERICA with craftsmanship and quality. Condensate Return Units / Shippensburg / / Fill Tanks / Boiler
More informationTECHNICAL. Series 18. Pump Packages
TECHNICAL S Y S T E M S Series 18 Pump Packages Series 18 Pump Packages Standard Features Close-coupled, end-suction, centrifugal pumps Mounted and wired pump starters Hand-Off-Auto switch for each pump
More informationFUEL-FIRED VERTICAL TUBELESS BOILERS
FUEL-FIRED VERTICAL TUBELESS BOILERS 4 60 P orizontal and Vertical Feedwater / Condensate Return Systems and Blow-down Tanks FULTON FUEL-FIRED VERTICAL TUBELESS BOILERS FULTON: AN INDUSTRY LEADER SINCE
More informationCondensate Pumps Jones Boulevard Limerick Airport Business Center Pottstown PA Tel:
www.watsonmcdaniel.com 428 Jones Boulevard Limerick Airport Business Center Pottstown PA 19464 Tel: 610-495-5131 129 Return Introduction Return System Shown below is a simplified view of a steam system
More informationUNFIRED STEAM GENERATORS STANDARD EQUIPMENT
CEMLINE Unfired Steam Generators are designed to produce clean steam with steam or high temperature hot water as an energy source for use where there is a need to produce clean steam from boiler steam
More informationTYPE.005 DA-2C. Deaerating Boiler Feed Pumps. SHIPCO Deaerators can save you money!!! BULLETIN 149 Revised 8/09
SHIPPENSBURG PUMP CO., INC. P.O. BOX 279, SHIPPENSBURG, PA 17257 PHONE 717-532-7321 FAX 717-532-7704 WWW.SHIPCOPUMPS.COM BULLETIN 149 Revised 8/09 TYPE.005 DA-2C Deaerating Boiler Feed Pumps SHIPCO Deaerators
More informationEssex County College - West Essex Campus Addition And Renovations dib # / SECTION HYDRONIC PIPING SPECIALTIES PART 1- GENERAL
Essex County College - West Essex Campus Addition And Renovations dib # 54292 / 11-14 SECTION 232116 - HYDRONIC PIPING SPECIALTIES PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions
More informationSTEAM AND CONDENSATE PIPING AND PUMPS DESIGN AND CONSTRUCTION STANDARD
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
More informationCustom Design TYPE SHM Steel Horizontal Make-up Boiler Feed Pumps and Custom Design TYPE SHEM. BULLETIN 107 Revised 5/17
SHIPPENSBURG PUMP CO. INC. P.O. BOX 279, SHIPPENSBURG, PA 17257 PH 717-532-7321 FAX 717-532-7704 WWW.SHIPCOPUMPS.COM BULLETIN 107 Revised 5/17 Custom Design TYPE SHM Steel Horizontal Make-up Boiler Feed
More informationFloat & Thermostatic Steam Traps for efficient condensate drainage of industrial process and HVAC equipment
Float & Thermostatic Steam Traps for efficient condensate drainage of industrial process and HVAC equipment Float & Thermostatic Steam Traps from Spirax Sarco About float & thermostatic steam traps Most
More informationUSG Series. Unfired Steam Generators Generate Clean Steam With Boiler Steam or High Temperature Hot Water as the Energy Source
USG Series Unfired Steam Generators Generate Clean Steam With Boiler Steam or High Temperature Hot Water as the Energy Source CEMLINE CORPORATION P.O. BOX 55 CHESWICK, PENNSYLVANIA 15024 Phone: (724) 274-5430
More informationArmstrong J Series Float, Thermostatic Steam Traps, Condensate Controllers & Liquid Drainers Installation and Maintenance Manual
Armstrong J Series, Thermostatic Steam Traps, Condensate Controllers & Liquid Drainers Installation and Maintenance Manual This bulletin should be used by experienced personnel as a guide to the installation
More informationInstallation, Operation, and Maintenance. For. Stickle Series AIV Spray-Tray Type Deaerating Feedwater Heaters. Introduction
Since 907 Steam Specialties Co., Inc. Installation, Operation, and Maintenance For Stickle Series AIV Spray-Tray Type Deaerating Feedwater Heaters Introduction The Stickle Spray-tray type Deaerator, as
More informationDeaerators for Industrial Applications
Deaerators for Industrial Applications Combined Cycle Power Plant Deaera Deaerator - a device that is widely used for the removal of oxygen and other dissolved gases from the feedwater to steam-generating
More informationSECTION STEAM AND STEAM CONDENSATE SPECIALTIES
SECTION 23 22 18 STEAM AND STEAM CONDENSATE SPECIALTIES PART 1 - GENERAL 1.1 SECTION INCLUDES A. Steam Traps. B. Flash Tanks. C. Condensate Return Units. D. Pressure Reducing Valves. E. Safety Valves.
More informationHoffman Specialty Pump Products
Condensate Units Boiler Feed Units Vacuum Heating Units Hoffman Specialty Pump Products S-0692C INDEX Condensate Return Units Series WC Series WCS Series SCC Boiler Feed Units Stock Watchman Condensate
More informationCustom Design TYPE CS
SHIPPENSBURG PUMP CO., INC. P.O. BOX 279, SHIPPENSBURG, PA 17257 PHONE 717-532-7321 FAX 717-532-7704 WWW.SHIPCOPUMPS.COM BULLETIN 109 Revised 3/05 Custom Design TYPE CS Cylindrical Steel Boiler Feed Pumps
More informationMOHICAN. MOHICAN 4-Pass Water Boiler, HP, PSI Section
SPECIFICATION SHEETS Steam Sample Specification Water Sample Specification MOHICAN SPECIFICATION SHEET The following sample specifications are provided by Superior Boiler Works to assist you in providing
More informationPackaged Steam Fired Water Heater
MODEL ST Packaged Steam Fired Water Heater Utilizes Steam To Heat Domestic Water, Semi-Instantaneous or Storage Type Heaters Features Reliable Packaged System Only high grade materials used in construction
More informationSAMPLE SPECIFICATIONS
Page 1 of 6 3-03 SAMPLE SPECIFICATIONS The following sample specifications are provided by Superior Boiler Works to assist you in providing your customer with the specific needs for that application. The
More informationINSTRUCTION AND REPAIR MANUAL
SECTION 6 ITEM 390 DATED JANUARY 2003 SUPERSEDES SECTION 6 ITEM 390 DATED OCTOBER 2000 INSTRUCTION AND REPAIR MANUAL SERIES 390 6 The 390 Series is a superior commercial Multi-Stage Vertical In-Line Centrifugal
More informationLiquid Drainers LIQUID DRAINERS
Liquid Drainers 206 Liquid Drainers Model/Series Type Body Material PMO Sizes Connection Page No. (PSIG) WLDE Float Ductile Iron 200 1 1 /2, 2, 2 1 /2 NPT WLDES Float Cast Steel 300 2 1 /2 NPT, SW, FLG
More informationStainless Steel Condensate Return Units
Stainless Steel Condensate Return Units Pressurized and Atmospheric Deaerators HIGH QUALITY STAINLESS STEEL EXCEPTIONAL VALUE, EXTRAORDINARY QUALITY industrialsteam.com Stainless Steel Condensate Return
More informationSECTION STEAM CONDENSATE PUMPS
SECTION 23 22 23 - STEAM CONDENSATE PUMPS PART I - GENERAL 1.1 SECTION INCLUDES A. Steam Condensate Return Units, Gravity Return Type 1. Receiver 2. Pumps 3. Control Panel 4. Accessories Note to PSC: Although
More informationFuel-Fired Vertical Tubeless Boilers
Fuel-Fired Vertical Tubeless Boilers Fulton Classic (4-60P), The EDGE (6-30P) orizontal and Vertical Feedwater / Condensate Return Systems and Blow-down Separators FULTON FUEL-FIRED VERTICAL TUBELESS BOILERS
More informationCondensate Recovery and Return System SDR A
Condensate Recovery and Return System SDR A Condensate tank of rectangular design type SDR A with high-pressure centrifugal pump(s) installed next to the tank Condensate tanks are used to collect the condensate
More informationPURGER INSTALLATION AND OPERATION BULLETIN PUR-SB17-02 SERVICE BULLETIN
VALVES VESSELS SYSTEMS CONTROLS PURGER INSTALLATION AND OPERATION BULLETIN PUR-SB17-02 SERVICE BULLETIN System drawings shown in this bulletin are for illustration purposes only. Refrigeration systems
More informationIn-Line Air Separators
Air Elimination & Control In-Line Air Separators The AC models of air separators deliver all the quality and performance you expect from Taco products. They are built to last with shell, heads and ANSI
More informationTechnical Data CONDENSATE COMMANDER PUMP SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY SD 9902D
Technical Data SD 9902D SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY 12586-2035 PRINTED IN U.S.A. SD 79902D/9803 Condensate Commander Pump Dimensions Weight Size A B C D E* F Lbs. 1"x
More informationDomestic Pump Series VCMD TM Combination Vacuum & Boiler Feed Unit
Custom engineered units to maintain optimum boiler levels and system vacuum requirements Four styles to choose from to minimize floor space requirements Multi-jet vacuum pumps for quiet, dependable and
More informationPamphlet A2404. Mechanical Pump & Pump/ Trap. GP Series GT Series
Pamphlet A2404 Mechanical Pump & Pump/ Trap GP Series GT Series Effective Processing Improves Plant Efficiency Increased productivity and product quality, plus reduced energy consumption and water treatment
More informationTABLE OF CONTENTS STEAM TRAPS INVERTED BUCKET SERIES PAGE FLOAT AND THERMOSTATIC SERIES PAGE THERMOSTATIC THERMODISC B0 26. How to Select All 107
TABLE OF CONTENTS FLOAT AND THERMOSTATIC SERIES PAGE How to Select All 107 C 14 H 8 I 12 X 14 Competitive Changeover 18 THERMOSTATIC 8C 22 9C 2 17C 20 Competitive Changeover 17C 24 Replacement Modules
More informationDesign and Construction Standards SECTION PLUMBING EQUIPMENT
SECTION 15450 PLUMBING EQUIPMENT PART 1 GENERAL 1.1 SECTION INCLUDES: A. Water heaters. B. Packaged water heating systems. C. Water storage tanks. D. Water softeners. E. Pumps. F. Circulators. 1.2 REFERENCES
More informationAPT and APT14 Automatic Pump Traps. for effective condensate drainage and removal
APT10-4.5 and Automatic Pump Traps for effective condensate drainage and removal 1 An innovative solution for effective heat User benefits Self contained compact unit. Operates with 8 in. installation
More informationPackaged Semi-Instantaneous Steam Fired Water Heater
MODEL STX Packaged Semi-Instantaneous Steam Fired Water Heater Shell and Tube Style Heater Features Reliable Only high grade materials used in construction to ensure long operating life Heat exchange pressure
More informationMODEL P. 2 ft. NPSH Cast Iron Bronze Fitted Low NPSH Centrifugal Pumps. BULLETIN 112 Revised 7/09. PH (Horizontal Flange Mounted)
SHIPPENSBURG PUMP CO., INC. P.O. BOX 279, SHIPPENSBURG, PA 17257 PHONE 717-532-7321 FAX 717-532-7704 WWW.SHIPCOPUMPS.COM BULLETIN 112 Revised 7/09 PH (Horizontal Flange Mounted) MODEL P 2 ft. NPSH Cast
More informationSeries 300 VTB. Installation Instructions
Series 300 VTB Installation Instructions Sizes 7 12 16 20 30 HP #2 Fuel Oil Gas (500 to 2500 BTU) Gas Light Oil Combination High Pressure Steam Sizes 7 thru 16 HP (125 PSI) Sizes 20 and 30 HP (150 PSI)
More informationCHAPTER 3 BASIC STEAM CYCLE
CHAPTER 3 BASIC STEAM CYCLE To understand steam generation, you must know what happens to the steam after it leaves the boiler. A good way to learn the steam plant on your ship is to trace the path of
More informationDomestic. Pump Series CB and CBE Condensate Units SINGLE OR DUPLEX 1,000 THRU 140,000 SQ. FT. EDR-250 THRU 34,748 LB./HR.
Cast Iron Receivers: For years of dependable service; warranted for 20 years from date of shipment against failure due to corrosion. Each Receiver comes standard with Inlet connection, an overflow and
More informationInstallation, Operation and Maintenance Guide. Steam Coil Installation, Operation and Maintenance. steam coils
Installation, Operation and Maintenance Guide Steam Coil Installation, Operation and Maintenance Guidelines for the installation, operation and maintenance of the Heatcraft brand of steam heating coils
More informationMini Pump Trap. Features: n Low maintenance - No leaking seals, impeller or motor problems reducing maintenance and downtime.
Armstrong Mini Pump Bulletin AFH-223 The Armstrong mini pump trap is the smallest non-electric solution that can move condensate or other liuids from lower to higher points and from lower to higher pressures.
More informationHoffman Specialty General Catalog
Hoffman Specialty General Catalog HS-900E ESP-PLUSTM For computer aided selection of Steam Trap and Regulators, please refer to the Steam Specialty Component Selectors in the Hoffman Specialty website
More informationDUPLEX CONDENSATE TANK SYSTEM
DUPLEX CONDENSATE TANK SYSTEM PROJECT NAME: 7 EAST 54TH STREET CONTRACTOR: PRO PUMP CORP ENGINEER: KEVAN WOODWORTH SUBMITTED BY: NISSIM ISAACSON DATE: 2.20.205 DESIGN DATA Model GPM TDH HP Volt Phase RPM
More informationInstallation and Maintenance "L" and "LS" Series
Installation and Maintenance "L" and "LS" Series IB-43-E This bulletin should be used by experienced personnel as a guide to the installation and maintenance of "L" and "LS" Series ultra capacity float
More informationBoiler Steam Supply Piping Basics November 18, ) Q: What kind of condensate traps should be used on vacuum condensate return systems?
Boiler Steam Supply Piping Basics November 18, 2015 1) Q: What kind of condensate traps should be used on vacuum condensate return systems? A: What is often used in a vacuum system is a thermodynamic disc
More informationBall Float Controlled. Thermo Dynamic(TD) Trap Safety Valve Condensate Pump Flash Vessel Moisture Separators Deaerator Head Steam Injector Sight Glass
Product of Quality Best Performance Ball Float Controlled Steam Traps Auto Drain Traps Float Valve Air Vent Valves Feed Control Valve Drain Control Valve Thermo Dynamic(TD) Trap Safety Valve Condensate
More informationDomestic Pump Condensate Transfer Equipment
Bulletin S-944L Domestic Pump Condensate Transfer Equipment CONDENSATE RETURN UNITS BOILER FEED UNITS LOW NPSH PUMPS VACUUM HEATING UNITS INDUSTRIAL VACUUM UNITS www.domesticpump.com Condensate Return
More informationFT600 & FT601* Steam Traps Float & Thermostatic Steam Trap. Float & Thermostatic STEAM TRAPS
STEAM TRAPS Steam Traps Steam Trap Model * Sizes 3/4, 1, 1 1 /2, 2, 3, 4 Connections NPT, SW, FLG Body Material Carbon Steel or 316SS Options Live Orifice Air Vent PMO Max. Operating Pressure 450 PSIG
More informationC. ASSE 1013: Performance Requirements for Reduced Pressure Principle Backflow Preventers.
SECTION 22 10 00 PLUMBING PIPING AND PUMPS PART 1 - GENERAL 1.1 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design.
More informationLATTNER BOILER COMPANY 9.5 HP Low-NOx Installation and Start-Up Checklist for Dry Cleaners
1 1. General Installation Information (to be completed by technician) Date installed: Location (city & state): Cleaner s name: National Board number (boiler): Installed by (company): Installed by (technician):
More informationHigh Capacity Instantaneous Steam Fired Water Heater
MODEL F High Capacity Instantaneous Steam Fired Water Heater Features Compact High Capacity Design Packaged System Water heater is factory assembled on an all welded steel mounting frame to save time and
More informationHORIZONTAL FIRE TUBE BOILERS Piping (HVAC) Pumping Equipment (HVAC).
SECTION 15555 HORIZONTAL FIRE TUBE BOILERS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15510 - Piping (HVAC). 2. 15540 - Pumping Equipment (HVAC). 1.02 SUBMITTALS A. Submit properly identified
More informationInverted Bucket Steam Traps. for efficient condensate drainage of industrial and HVAC equipment
Inverted ucket Steam Traps for efficient condensate drainage of industrial and HVC equipment Inverted ucket steam traps The proper drainage of condensate is essential to efficient steam system operation.
More informationSECTION PLUMBING EQUIPMENT
PART 1 GENERAL 1.1 SECTION INCLUDES A. Water heaters B. Packaged water heating systems C. Water storage tanks D. Water softeners E. Pumps F. Circulators 1.2 REFERENCES SECTION 22 30 00 PLUMBING EQUIPMENT
More informationVent-Rite. Cast Iron And Steel Receivers. Simplex, Duplex, Triplex And Quadruplex Units. Pump Capacities To 150 GPM. Discharge Pressure To 75 PSI
Vent-Rite BULLETIN VCRV AUGUST 0 GUARDIAN Plus Cast Iron And Steel Receivers Simplex, Duplex, Triplex And Quadruplex Units Pump Capacities To 0 GPM Discharge Pressure To 7 PSI 87 Dewey Avenue Benton Harbor,
More informationA. This Section includes the following domestic water piping specialties:
SECTION 221119 DOMESTIC WATER PIPING SPECIALTIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationThermal Fluid Heaters
Thermal Fluid Heaters Vertical Coil, Vertical Tubeless, Electric and Horizontal Sizes from 75,000 to 40,000,000 BTU/HR The heat transfer innovators. THERMAL FLUID FEATURES AND BENEFITS KEY FEATURES No
More informationBOHEC R CRS86A DISHWASHER STANDARD FEATURES MODEL ACCESSORIES DIRECTION OF OPERATION VOLTAGE OPTIONS AT EXTRA COST
Item # Quantity C.S.I. Section 11400 DISHWASHER STANDARD FEATURES 244 racks per hour Opti-RinSe system Ball detent clutch conveyor drive mechanism Top mounted controls Stainless steel anti-clogging wash
More informationSeries 1140 and 1141 Temperature Regulators
Hoffman Specialty Installation & Maintenance Instructions HS-504(E) Series 1140 and 1141 Temperature Regulators! CAUTION FOLLOW ALL INSTALLATION AND OPERATING INSTRUCTIONS. TURN OFF WATER OR STEAM BEFORE
More informationA-8-01 Typical questions and answers on the boiler specifications on tender and boiler contract documents
Boiler specifications A-8-01 Typical questions and answers on the boiler specifications on tender and boiler contract documents Burner General: Q. Burner and burner safeguards shall comply with the CGA
More informationSteam Ancillary Equipment. Primary Steam System, Water Treatment and Auxiliary Steam System Equipment
Steam Ancillary Equipment Primary Steam System, Water Treatment and Auxiliary Steam System Equipment WITH ANCILLARY EQUIPMENT Steam Header with Accumulator Gas Train Assembly Single Point Gas Supply Trap
More informationFEEDWATER TANK WITH DEAERATOR DATASHEET. Capacity 1000 to lt Operating Pressure 0,5 bar
DATASHEET FEEDWATER TANK WITH DEAERATOR Capacity 1000 to 20000 lt Operating Pressure 0,5 bar Steam boiler feedwater tank with stainless steel Deaerator Oxygen Removal - Water Preheating and Storage DSEN001-01
More informationYARWAY PROCESS THERMODYNAMIC STEAM TRAPS SERIES 40/40D AND C250/260
SERIES 40/40D AND C250/260 Designed for a variety of high pressure and high capacity applications found in utility, industrial and marine service FEATURES Designed to fail open. Designed for superheat
More informationInverted Bucket Float & Thermostatic Radiator Traps STEAM CONTROL PRODUCTS STEAM TRAPS
Inverted Float & Radiator Traps STEAM CONTROL PRODUCTS STEAM TRAPS ABOUT US In 1916, the company, then known as the Sterling Engineering Company, began designing and manufacturing valves, traps, strainers
More informationHEAT GENERATION 1.01 RELATED CORNELL DESIGN AND CONSTRUCTION STANDARDS. B. Section HVAC Basic Materials and Methods
230520 HEAT GENERATION Cornell s Design and Construction Standards provide mandatory design constraints and acceptable or required products for all construction at Cornell University. These standards are
More informationSPECIFICATIONS MODEL E859C MINI DEHYDRATOR
SPECIFICATIONS MODEL E859C MINI DEHYDRATOR 1 DEHYDRATION TECHNOLOGY This proposal describes the equipment which shall be supplied by ENERVAC for a system for processing (dehydrating, de-aerating, purifying
More informationWHY THE REMOVAL OF NONCONDENSABLE GASES AND AIR IS CRITICAL IN A STEAM SYSTEM
BEST PRACTICE NO. 30 WHY THE REMOVAL OF NONCONDENSABLE GASES AND AIR IS CRITICAL IN A STEAM SYSTEM Air and noncondensable gases are one of the major problems in a steam system that can cause production
More informationTechnical Data TYPE T14 & T14D TEMPERATURE PILOT SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY SD 4511A T14 PILOT
Technical Data SD 4511A SPENCE ENGINEERING COMPANY, INC. 150 COLDENHAM ROAD, WALDEN, NY 12586-2035 TYPE T14 & T14D TEMPERATURE PILOT PRINTED IN U.S.A. SD 4511A/9811 5 13 /16 D 4 7 /8 1 13 /16 T14 PILOT
More informationWater Piping and Pumps
Technical Development Program DISTRIBUTION SYSTEMS Water Piping and Pumps PRESENTED BY: Michael Ho carriertdp@gmail.com 424-262-2144 Menu Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section
More informationA hydronic system controls comfort by delivering heated or cooled fluid to the conditioned space through pipes.
Introduction to Hydronics A hydronic system controls comfort by delivering heated or cooled fluid to the conditioned space through pipes. Hydronic heating systems use hot water or steam to deliver the
More informationFLO-RITE-TEMP INSTANTANEOUS WATER HEATER INSTALLATION AND ADJUSTMENT INSTRUCTIONS FOR SINGLE AND DOUBLE WALL UNITS
FLO-RITE-TEMP INSTANTANEOUS WATER HEATER INSTALLATION AND ADJUSTMENT INSTRUCTIONS FOR SINGLE AND DOUBLE WALL UNITS Bulletin No. AY-780-L This bulletin should be used by experienced personnel as a guide
More informationClearFire Economizer Model ECF Integral or External. Addendum to manuals CFH and CFV
ClearFire Economizer Model ECF Integral or External Addendum to manuals 750-295 CFH and 750-269 CFV CB-8466 08/2011 1-GENERAL The Model ECF economizer is a stainless steel coil tube arrangement using
More informationInverted Bucket Steam Traps
INSTALLATION AND MAINTENANCE INSTRUCTIONS IM-2-00-US December 201 Inverted Bucket Steam Traps Safety Information Safe operation of these products can only be guaranteed if they are properly installed,
More informationSECTION STEAM CONDENSATE PUMPS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 23 22 23 STEAM CONDENSATE PUMPS SPEC WRITER NOTES: 1. Delete between // ---- // if not applicable to project. Also delete any other item or paragraph not applicable
More informationBOILER HOUSE PRODUCTS GMS
GMS BOILER HOUSE PRODUCTS Contents Page 2 Introduction 3 Condensate Pumpsets 6 Blowdown Vessels 8 Boiler Feed Tanks Page 10 Chemical Dosing Pots 11 Vent Heads 11 De-Aerator Heads Introduction to Boiler
More informationBASIL 6000 TUNNEL CAGE WASHER
BASIL 6000 TUNNEL CAGE WASHER APPLICATION For thorough, efficient cleaning of cages, debris pans, bottles, feeder bowls, and miscellaneous items used in the care of laboratory animals. DESCRIPTION The
More informationSECTION PLUMBING EQUIPMENT
PART 1 GENERAL 1.01 SECTION INCLUDES A. Water heaters. B. Packaged water heating systems. C. Domestic water heat exchangers. D. Water storage tanks. E. Water softeners. F. Reverse osmosis equipment. G.
More informationInstant hot water Feed-Forward system unlimited supply accurate to +/- 4 F
Count on Graham for proven reliability. Graham is one of the world s foremost designers and manufacturers of vacuum and heat transfer equipment with over a half-century of proven experience. Our in-house
More informationCondensate Boiler Feed Water Make-Up
1144 Utica Ave, Brooklyn, NY 1103 July 0 New Catalogue Release Bulletin 9C.01 Low Inlet Condensate Receiver (7 from floor) Close Grained Cast Iron Simplex and Duplex Design To 0,000 SQ-Ft EDR Pump Capacity
More informationSemi-Instantaneous Indirect Fired Water Heater
MODEL BWX Semi-Instantaneous Indirect Fired Water Heater Use Boiler Water Or HTHW To Heat Domestic Water Features Reliable Only high grade materials used in construction to ensure long operating life Hydrastone
More informationEconomical and simplified solutions that offer quality and optimum steam trap service.
Economical and simplified solutions that offer quality and optimum steam trap service. It All Comes Down To Protection Regardless of the temperature and pressure characteristics of steam line drips or
More informationCentrifugal Blowdown Separators and Tanks
Centrifugal Blowdown Separators and Tanks Function: Madden Blowdown separators are designed to immediately dispose of hot, high pressure boiler blowdown. When the hot, high pressure bottom blowdown from
More informationYARWAY NON-REPAIRABLE DRIP AND TRACER STEAM TRAPS SERIES PB, 29, 129Y AND 29S
SERIES PB, 29, 129Y AND 29S Economical and simplified solutions that offer quality and optimum steam trap service FEATURES 29S 29 Thermostatic traps Pressure assisted fail-open design Freeze proof Easy
More information