HWT-P HWAT POWER CONNECTION KIT WITH END SEAL INSTALLATION INSTRUCTIONS
|
|
- Donald Harrison
- 6 years ago
- Views:
Transcription
1 HWT-P HWAT POWER CONNECTION KIT WITH END SEAL INSTALLATION INSTRUCTIONS DESCRIPTION The Raychem HWT-P Power Connection and End Seal Kit is for use with HWAT heating cables. Materials for one power connection and one end seal are included in this kit. These installation instructions should be used in conjunction with the HWAT System Installation and Operation Manual (H). For technical support contact your Pentair Thermal Management representative or call Pentair Thermal Management at TOOLS REQUIRED Screw driver Needle-nose pliers Utility knife Tape measure Pen Diagonal cutters Heat gun or torch Channel lock pliers ADDITIONAL MATERIALS REQUIRED (NOT PROVIDED IN THIS KIT) UL Listed or CSA Certified junction box suitable for the location, with a through hole or threaded hub for /-inch NPT. KIT CONTENTS Item Qty Description A HWAT water heater tag B Gel-filled end seal C Pipe mounting bracket D # pipe strap E Black heat-shrinkable tubes ( in x in) F Green/yellow heat-shrinkable tube ( in x in) G Warning labels H Wire nuts (red) I Wire nut (gray) J Black heat-shrinkable tube ( in x in) K Lock nut L Cable gland M Black washer N Plastic cable tie APPROVALS K Pipe Heating Cable -G HWAT heating cables are UL Listed, CSA Certified, and FM Approved when used with the appropriate agency-approved Raychem components and accessories. The components are intended for use in dry and accessible locations. A B C D E F For HWAT Systems install this tag on the hot water heater or temperature control valve servicing the hot water systems. MAX. ATTENTION 0 F DO NOT heat water above 0 F. Temperatures above 0 F will permanently reduce the power output of the HWAT heating cable used on this hot water system. PN P00000 H0 0/ 0 Pentair Thermal Management LLC G H I J K L M N WARNING: This component is an electrical device that must be installed correctly to ensure proper operation and to prevent shock or fire. Read these important warnings and carefully follow all the installation instructions. To minimize the danger of fire from sustained electrical arcing if the heating cable is damaged or improperly installed, and to comply with the requirements of Pentair Thermal Management, agency certifications, and national electrical codes, groundfault equipment protection must be used. Arcing may not be stopped by conventional circuit breakers. Bus wires will short if they contact each other. Keep bus wires separated. Keep components and heating cable ends dry before and during installation. The black heating cable core is conductive and can short. It must be properly insulated and kept dry. Component approvals and performance are based on the use of Pentair Thermal Management specified parts only. Do not use substitute parts or vinyl electrical tape. Use fire-resistant insulation materials. Do not damage cable jackets or braid. Remove any damaged cables or connections from service. Do not use aluminum feed wires. Leave these instructions with end user for reference and future use. THERMAL BUILDING SOLUTIONS EN-RaychemHWTP-IM-H0 0/ CAUTION: HEALTH HAZARD: Overheating heat-shrinkable tubes will produce fumes that may cause irritation. Use adequate ventilation and avoid charring or burning. Consult MSDS RAY for further information. CHEMTREC -hour emergency telephone: (00) -00 Non-emergency health and safety information: (00) -. /
2 Power Connection Installation HWAT Modified polyolefin outer jacket Tinned-copper braid Polymer-coated aluminum wrap Modified polyolefin inner jacket Self-regulating conductive core Nickel-plated copper bus wires in. (0 cm) Unscrew cable gland (Item L). Discard white washer and use black washer (Item M) instead. Slide nut, washer and grommet over the cable as shown. Bevel on the washer should face into the nut. Black washer / in Lightly score completely around and then down outer jacket. Bend heating cable to break jacket at score then peel off outer jacket. Do not cut metal braid or inner jacket. Carefully slide screwdriver underneath the braid and poke tip of screwdriver up through - bundles of the braid wire. Slowly pull back on screwdriver to unravel braid. Straighten out braid wire Repeat until entire length of braid is unraveled. THERMAL BUILDING SOLUTIONS EN-RaychemHWTP-IM-H0 0/ /
3 Straighten the braid and twist braid into a pigtail. Do not shorten the braid. Do not cut bus wires. / in in Using wire cutters, cut away aluminum wrap. At the end of each heating cable, lightly score completely around and down inner jacket Bend heating cable to break jacket at score, then peel off inner jacket Notch core at the end Twist back and peel bus wires from core Score between bus wires at base jacket Bend core to break free at base jacket / in Do not cut bus wires. Peel core and any remaining material from bus wires Slide heat-shrinkable tubes (Item E) over the bus wires. Starting from the center of the tube, move the heat source continuously from side to side. 0 Slide heat-shrinkable tube (Item J) over the stripped portion of the cable, until tube butts up against the outer jacket. IMPORTANT: If using a torch, be careful not to overheat, char or damage the tube. CAUTION: Health Hazard. Consult material safety data sheet RAY. To prevent the shrink tube from moving, slightly spread the bus wires to hold tube in place while shrinking. THERMAL BUILDING SOLUTIONS EN-RaychemHWTP-IM-H0 0/ /
4 Starting at center of tube, move heat source continuously from side to side. While tube is still hot, pinch with pliers between bus wires to seal; hold for 0 seconds. / in / in / in CAUTION: Health Hazard. Consult included material safety data sheet. CAUTION: To avoid burns allow heated sections to cool before touching. Slip green/yellow tube (item F) over braid and shrink. Note: Ensure junction box is in proper orientation and tighten to pipe mounting bracket (Item C). In some cases, it may be required to install the junction box in the o'clock or o'clock position on the pipe. Lock nut Note: For junction boxes with a through hole, use provided lock nut (Item K). CAUTION: Health Hazard. Consult included material safety data sheet. Slide grommet until end is /" from end of outer jacket Bring cable into junction box Hand tighten nut With channel lock pliers tighten nut, but do not exceed more than one () turn. /" THERMAL BUILDING SOLUTIONS EN-RaychemHWTP-IM-H0 0/ /
5 Use red wire nuts (Item H) to connect the supply with the heating cable bus wires. Red wire nuts (Item H) Apply warning label (Item G) to junction box cover. Gray wire nut (Item I) Ground wire Use gray wire nut (Item I) to connect the ground braid to the supply ground. Attach HWAT water heater tag (Item A) to either the water heater or temperature control valve servicing the hot water systems, using the plastic cable tie (Item N). Hot water out Tempered water out Hot water in Water heater For HWAT Systems install this tag on the hot water heater or temperature control valve servicing the hot water systems. MAX. ATTENTION 0 F DO NOT heat water above 0 F. Temperatures above 0 F will permanently reduce the power output of the HWAT heating cable used on this hot water system. 0 Pentair Thermal Management LLC PN P00000 H0 0/ HWAT water heater tag Mixing valve Cold water in THERMAL BUILDING SOLUTIONS EN-RaychemHWTP-IM-H0 0/ /
6 End Seal Installation for HWAT Heating Cables Score down and around outer jacket inch from the end. Remove the outer jacket. Do not cut or damage inner jacket. Remove exposed braid. " Using wire cutters, cut away aluminum wrap close to braid and outer jacket. Push end seal completely onto heating cable. Wipe off excess gel that may ooze out after you insert the heating cable. Note: The end seal can be installed only once; it cannot be removed from the heating cable. NORTH AMERICA PENTAIR THERMAL MANAGEMENT LLC EUROPE, MIDDLE EAST, AFRICA PENTAIR THERMAL MANAGEMENT BELGIUM NV ASIA PACIFIC PENTAIR THERMAL (SHANGHAI) CO. LTD LATIN AMERICA PENTAIR THERMAL MANAGEMENT LLC Tel: Fax: Tel: Fax: Tel: +... Fax: Tel: +... Fax: +... Tel: Fax: +... Pentair and HWAT are owned by Pentair or its global affiliates. All other trademarks are the property of their respective owners. Pentair reserves the right to change specifications without prior notice. -0 Pentair. P THERMAL BUILDING SOLUTIONS EN-RaychemHWTP-IM-H0 0/ /
FTC-HST WARNING: CAUTION:
FTC-HST XL-Trace, RaySol, and IceStop Splice/Tee Connection Kit Installation Instructions Description The Raychem FTC-HST is used with RaySol system heating cables to make splice connections (on slab bottoms
More informationJB-RTD-STAND RTD PIPE STAND FOR COMBINATION POWER CONNECTION BOX AND ELECTRONIC CONTROLLER INSTALLATION INSTRUCTIONS
JB-RTD-STAND RTD PIPE STAND FOR COMBINATION POWER CONNECTION BOX AND ELECTRONIC CONTROLLER INSTALLATION INSTRUCTIONS JB-RTD-STAND with Raychem heating cable DESCRIPTION The Raychem JB-RTD-STAND is a combination
More information1SC-SSC Splice Connection Kit Installation Instructions
1SC-SSC Splice Connection Kit Installation Instructions Description The 1SC-SSC is a NEMA 4 rated splice connection kit for use with Raychem 1SC30, 40, 50, 60, 70, 80 (-CT) and 1SC/H30, 40, 50, 60, 70,
More informationC A Heating Cable Gland Kit
C75-100-A Heating Cable Gland Kit Installation Instructions Description The C75-100-A is a NEMA 4X rated gland kit used to transition heating cables into a junction box when making connections off of a
More informationJBM-100-LBTV2 Power Connection, Powered Splice, Dual Power Connection, or Splice with Junction Box
JBM-100-LBTV2 Power Connection, Powered Splice, Dual Power Connection, or Splice with Junction Box Installation Instructions Description The JBM-100-LBTV2 is a Type 4X-rated connection kit. It is designed
More informationJBS-100-EC Electronic controller replacement kit for JBS-100-ECP-A and JBS-100-ECW-A Installation Instructions
JBS-100-EC Electronic controller replacement kit for JBS-100-ECP-A and JBS-100-ECW-A Installation Instructions Description The Raychem JBS-100-EC is a replacement kit that can be used to replace the electronic
More informationJBS-100-ECP-A COMBINATION POWER CONNECTION BOX AND DIGITAL ELECTRONIC CONTROLLER INSTALLATION INSTRUCTIONS
JBS-100-ECP-A COMBINATION POWER CONNECTION BOX AND DIGITAL ELECTRONIC CONTROLLER INSTALLATION INSTRUCTIONS JBS-100-ECP-A with Pyrotenax MI heating cable using required MI cable grounding kit JBS-100-ECP-A
More informationFreezGard. Self-regulating crankcase heater. Product Overview
Self-regulating crankcase heater Product Overview When compressors operate in cold areas, refrigerant can migrate into the crankcase oil whenever the compressor is not running. On start-up, this can cause
More informationC Electrical Connection Kit
1548-4010C Electrical Connection Kit For Use With Dekoron 2700 and 2300 Family of Heating Cables Installation Instructions Kit Description The Dekoron 1548-4010C electrical connection and end seal kit
More informationRayClic Connection System
RayClic Connection System RayClic-S Splice Kit RayClic-T Tee and End Seal Kit RayClic-X Cross and End Seal Kit Installation Instructions Description These kits are for use with Raychem IceStop, XL-Trace
More informationHOT WATER TEMPERATURE MAINTENANCE HWAT SYSTEM
HOT WATER TEMPERATURE MAINTENANCE HWAT SYSTEM This step-by-step design guide provides the tools necessary to design a Raychem HWAT Hot Water Temperature Maintenance System. For additional information,
More informationData Sheet. Self regulating heating tapes. RS stock numbers
Data Pack K Issued September 2001 232-3125 Data Sheet Self regulating heating tapes RS stock numbers 379-312 The information contained within this sheet regarding applications and installation of RS WinterGard
More informationHS-TSPLICE - HEATSHRINK TEE / SPLICE. Installation Instructions
- HEATSHRINK TEE / SPLICE This kit is only for use with the following Drexan HeatTracer Self-Regulating heater products: PipeGuard Warm (PGW), MultiTrace (MT) and HotTape (HT). CAUTION: A ground fault
More informationData Sheet. Self regulating process heating tapes RS stock numbers ,
Data Pack K Issued March 1997 232-3333 Data Sheet Self regulating process heating tapes RS stock numbers 379-889, 379-974 The information contained within this sheet regarding applications and installation
More informationHEATING CABLE RATINGS APPROVALS* Drexan Energy Systems, Inc. Kelowna, BC, Canada, V4V 1S5
DREX0019 Division 1 Adapter Kit Single Cable These installation instructions are only for use with the following Drexan HeatTracer heater products: Self-Regulating (PipeGuard Warm (PGW), MultiTrace (MT)
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The SLT-LPS Entry Seal Kit provides a watertight entry into a junction box suitable for this application. This kit includes cable seals for power and end terminations. The SLT-LPS kit is designed
More informationDesign Guide Design Notes Design Examples Technical Data Sheets Expanded Capabilities Specifications Warranty
Introduction HWAT Design Guide This step-by-step design guide provides the tools necessary to design a Raychem HWAT Hot Water Temperature Maintenance System. For additional information, contact your Pentair
More informationH908 WinterGard Plug-in Power Connection Kit with End Seal
R R H908 WinterGard Plug-in Power Connection Kit with End Seal Installation Instructions Description The H908 is a plug-in, ground-fault-protected power connection kit for use with WinterGard H311, H611,
More informationTT3000 and TT5000 Series
TT3000 and TT5000 Series Bulk Sensing Cable Installation Instructions General Notes Do s and Don ts General Information These instructions detail techniques used to install TT3000 or TT5000 bulk sensing
More informationCSI Master Format 2004 Guide Specification for: Flow Maintenance of Aboveground Fuel Oil Lines
CSI Master Format 2004 Guide Specification for: Flow Maintenance of Aboveground Fuel Oil Lines System for flow maintenance of aboveground fuel oil lines with Proportional Ambient Sensing Control (PASC),
More informationLongline Heating. Contents. Introduction
Longline Heating This section provides an overview of the longline heat-tracing technologies available from Pentair Industrial Heat Tracing Solutions. For complete design assistance, contact your Pentair
More informationCSI Master Format 2012 Guide Specification for: Hot Water Temperature Maintenance (HWAT) Systems
CSI Master Format 2012 Guide Specification for: Hot Water Temperature Maintenance (HWAT) Systems System for temperature maintenance of domestic hot water supply systems with energy efficient time based
More informationCSI Master Format 2004 Guide Specification for: Flow Maintenance of Above Ground Greasy Waste Disposal Lines
CSI Master Format 2004 Guide Specification for: Flow Maintenance of Above Ground Greasy Waste Disposal Lines System for flow maintenance of above ground greasy waste disposal lines with line sensing control,
More informationTTSIM-2 TRACETEK SENSOR INTERFACE MODULE WITH LCD AND RELAY INSTALLATION/OPERATION INSTRUCTIONS
TTSIM-2 TRACETEK SENSOR INTERFACE MODULE WITH LCD AND RELAY INSTALLATION/OPERATION INSTRUCTIONS GENERAL INFORMATION Please read these instructions and keep them in a safe place. These instructions must
More informationCOMMERCIAL & RESIDENTIAL SELF-REGULATING HEATING PRODUCTS APPLICATION AND DESIGN GUIDE EUROPE, MIDDLE EAST, AFRICA
WWW.PENTAIRTHERMAL.COM NORTH AMERICA Tel: +1.800.545.6258 Fax: +1.800.527.5703 Tel: +1.650.216.1526 Fax: +1.650.474.7711 thermal.info@pentair.com ASIA PACIFIC Tel: +86.21.2412.1688 Fax: +86.21.5426.2917
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The PLT-L Series End of Circuit Light Kit is for use with all versions of LT, CLT, HLT and NC heater cables. Compatible for use with any vendor s heater cables smaller than 11mm (.44 ) diameter.
More informationFrost Heave Protection System Installation and Operation Manual
Frost Heave Protection System Installation and Operation Manual FHPC Constant Power Density Heating Cable Systems Thermal management solutions EN-RaychemFHPS-IM-INSTALL103 R1 WARNING: Fire and Shock Hazard.
More informationCSI Master Format 2004 Guide Specification for: Freezer Frost Heave Prevention (Mineral Insulated)
CSI Master Format 2004 Guide Specification for: Freezer Frost Heave Prevention (Mineral Insulated) System for preventing frost heave in freezers, cold rooms and ice arenas with temperature control, monitoring,
More informationConsignes d installation
PBS-200-A Single entry power junction box Installation Instructions PBS-200-A Single entry power junction box with cold applied connection technology for use with BARTEC PSB / HSB trace heaters Consignes
More informationTHERMAL BUILDING SOLUTIONS EN-TraceTekTTSIM1A-IM-H /16
TraceTek TTSIM-1A TraceTek Sensor Interface Module with Relay Installation/OPERATION Instructions Approvals and Certifications TYPE NM General Signaling Equipment 76LJ Only AC versions are UL listed and
More informationNELSON HEAT TRACING SYSTEMS ALT-BC STANDARD POWER CONNECTION KIT
DESCRIPTION The ALT-BC Standard Power Connection Kit is constructed of cast aluminum for use with all versions of Nelson Heat Tracing Systems LT, CLT, HLT and NC heater cables. Compatible for use with
More informationDESCRIPTION. 42 mm. 125 mm
RMM2-DI TRACE-HEATING REMOTE MONITORING MODULE FOR DIGITAL INPUTS DESCRIPTION 125 mm 60 mm The Remote Monitoring Module for Digital Inputs (RMM2-DI) provides the capability for the Raychem NGC controller
More informationSensor Interface Module Installation/Operation Instructions
TraceTek TTSIM-1 Sensor Interface Module Installation/Operation Instructions Approvals and Certifications TYPE NM General Signaling Equipment 76LJ Only AC versions are UL listed and VDE Certified. For
More informationNGC-UIT-ORD User interface terminal for Raychem NGC systems Installation Instructions
NGC-UIT-ORD User interface terminal for Raychem NGC systems Installation Instructions Description The NGC-UIT-ORD is a panel mounted display used in conjunction with other approved Raychem control and
More informationDRAIN WATER TEMPERING INSTALL
! WARNING! CAUTION DRAIN WATER TEMPERING KIT - 0601-00-07-86 WARNING! This kit should be installed only by qualified service personnel to reduce the risk of electric shock, serious injury, or fire. A plumbing
More informationSERGE BARIL GTKB GUT TRACE KIT BAG
Description: The GTKB Gut Trace Kit Bag includes the power cord connection with the GFI Plug and end seal. It is for use with FPS-BT & IN-PIPE type heater cables. Kit Contents: 1 Compression Fitting 3
More informationFactory and Field Installed Splices
Product Overview Splices for copper-sheathed cables Factory and field installed fire-rated and non-fire-rated splices are used to join individual lengths of Pyrotenax MI cable in cases where the manufactured
More informationTraceTek Sensing Cable for Aboveground Leak Detection Installation Instructions
TT5000-HUV (for fuel leaks) TT5001-HUV (for solvent leaks) TraceTek Sensing Cable for Aboveground Leak Detection Installation Instructions TT5000-HUV sensing cable is identified by the red tracer in the
More informationHHS-WWH HOPPER HEATING SYSTEM WRAP-WOUND HEATER INSTALLATION INSTRUCTIONS DESCRIPTION. HHS-WWH PRODUCT SPECIfICATIONS
HHS-WWH HOPPER HEATING SYSTEM WRAP-WOUND HEATER INSTALLATION INSTRUCTIONS HHS-WWH PRODUCT SPECIfICATIONS Power density Standard wattages up to 4650 W/m² (3.0 W/in²) Voltage range (nominal) 120 to 600 VAC
More informationFIRE SPRINKLER SYSTEM FREEZE PROTECTION XL-TRACE SYSTEM
FIRE SPRINKLER SYSTEM FREEZE PROTECTION XL-TRACE SYSTEM This step-by-step design guide provides the tools necessary to design a Raychem XL-Trace fire sprinkler freeze protection system. For other applications
More informationQAA 142 Termination instructions Self-regulating trace heaters type ELSR-NA and -HA in Div1 with heater entry kit EL-HAZELECT Kit part No: 09CA051
QAA 142 Termination instructions Self-regulating trace heaters type ELSR-NA and -HA in Div1 with heater entry kit EL-HAZELECT Kit part No: 09CA051 QAA 142 Instruction de terminaison pour des câbles chauffants
More informationROOF ICE MELT (RIM2) SYSTEM
FOR CONCEALED ROOF & GUTTER DE-ICING PRODUCT OVERVIEW The Raychem RIM System is our premier engineered, aesthetically elegant, concealed roof & gutter de-icing solution to prevent ice dams, icicles, and
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The ALT- continuity monitor device is used to monitor bus continuity on a parallel type heater cable. After the heater cable is installed on the pipe, connect the ALT- to the opposite end of
More informationsulfur transport pipelines Safe, Reliable and Cost-Effective Heat Management System
sulfur transport pipelines Safe, Reliable and Cost-Effective Heat Management System INDUSTRIAL HEAT TRACING SOLUTIONS WWW.pentairthermal.com industrial solutions As the world s largest provider of complete
More informationCSI Master Format 2004 Guide Specification for: Snow Melting (Mineral Insulated)
CSI Master Format 2004 Guide Specification for: Snow Melting (Mineral Insulated) Typical system for snow melting of pavers, concrete and asphalt surfaces with temperature and moisture sensing control,
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The Z1-PLT-BC Power Connection Kit is designed for terminating on heater cable to customer supplied power wiring. This kit is designed for use with all wattages of Nelson Heat Tracing Systems
More informationXAGA 550/550-L. Aerial Splice Closure. 1. General Description. 2. Warnings. 3. Cautions
XAGA 550/550-L Aerial Splice Closure I N S T A L L A T I O N I N S T R U C T I O N S 1. General Description 1. This practice provides information regarding the description and use of the XAGA 550/550-L
More informationNELSON HEAT TRACING SYSTEMS INSTALLATION
DESCRIPTION The ALT-BY Tee Splice Connection Kit is constructed of cast aluminum for use with all versions of Nelson Heat Tracing Systems LT, CLT, HLT and NC heater cables. Compatible for use with any
More informationXL-Trace System Application and Design Guide
R XL-Trace System Application and Design Guide Pipe Freeze Protection and Flow Maintenance for Commercial Construction Applications Pipe Freeze Protection and Flow Maintenance 1. Pipe Freeze Protection
More informationHot Water Temperature Maintenance. HWAT System. Product Selection and Design Guide
Hot Water Temperature Maintenance HWAT System Product Selection and Design Guide A Solutions Company Tyco Thermal Controls provides complete heat tracing and specialty wiring solutions for the industrial,
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The PLT-BY Tee Splice Connection Kit is for use with all versions of Nelson Heat Tracing Systems LT, CLT, HLT and NC heater cables. Compatible for use with any vendor s heater cables small
More informationTOUCH 1500 User Interface Terminal for Raychem NGC Systems Installation Instructions
TOUCH 1500 User Interface Terminal for Raychem NGC Systems Installation Instructions Approvals / Certifications Hazardous Locations Class I, Division 2 Groups A, B, C, D Touch 1500-HAZ-CPU and Touch 1500-HAZ-TS
More informationWARNING DESCRIPTION PART NUMBER QTY PLUMBING, DYNATEMP DRAIN QUENCH BRACKET, THERMOSTAT DRAIN QUENCH
! WARNING WARNING: This kit should be installed only by qualified service personnel to reduce the risk of electric shock, serious injury, or fire. A plumbing permit and the services of a licensed plumber
More informationTECK-40 Series 1000V Class Splice for 4/C Armored Teck Power Cables
Product Installation Instructions TECK-0 Series 000V Class Splice for /C Armored Teck Power Cables Raychem Tyco Electronics - Energy 8000 Purfoy Road Fuquay-Varina, NC 756 PII-598 Rev AC The following
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The Z1-PLT-LPM Power Connection Kit is designed for terminating one heater cable to customer supplied power wiring. This kit is designed for use with all wattages of Nelson Heat Tracing Systems
More informationTT3000 and TT5000 Series
TT3000 and TT5000 Series Modular Sensing CableS Installation Instructions General Information These instructions explain the proper procedures for installing and testing TT3000 and TT5000 series modular
More informationDESTU. Direct Entry Sealed Termination Unit. Installation Instructions. Suitable for use in either safe or hazardous areas.
DESTU Direct Entry Sealed Termination Unit Installation Instructions Suitable for use in either safe or hazardous areas R II 2 G EEx e II Heat Trace Limited, Mere s Edge, Chester Road, Helsby, Frodsham,
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationROOF ICE MELT (RIM) SYSTEM
Pipe Freeze Protection and Flow Maintenance ROOF ICE MELT (RIM) SYSTEM FOR CONCEALED ROOF & GUTTER DE-ICING Fire Sprinkler System Freeze Protection PRODUCT OVERVIEW The Raychem RIM System is our premier
More informationTraceTek Sensing Cable for Underground Leak Detection Installation Instructions. Description. Heat shrink tubing segments. Optional Materials
TT5000-HS (for fuel leaks) TT5001-HS (for solvent leaks) TraceTek TraceTek Sensing Cable for Underground Leak Detection Installation Instructions Description These instructions explain the proper procedures
More informationWARNING. Failure to install this kit within the guidelines might adversely affect safety, performance, component life and warranty coverage.
! WARNING WARNING: This kit should be installed only by qualified service personnel to reduce the risk of electric shock, serious injury, or fire. A plumbing permit and the services of a licensed plumber
More informationV Refrigeration Module
5800 230V Refrigeration Module Removal and Replacement Instruction Sheet 60-4702-062 Revision F, January 25, 2016 These instructions cover the 4700 and 5800 230V refrigerator module replacement. Before
More informationNGC-UIT2-ORD-R Remote User Interface Terminal for Raychem NGC Systems Installation Instructions
NG-UIT2-ORD-R Remote User Interface Terminal for Raychem NG Systems Installation Instructions Description The NG-UIT2-ORD-R is a wall-mounted display which allows the User Interface Terminal (UIT) to be
More informationPipe Freeze Protection. Flow Maintenance. Introduction. XL-Trace System
Pipe Freeze Protection and Flow Maintenance 1. Pipe Freeze Protection and Flow Maintenance Introduction XL-Trace System This step-by-step design guide provides the tools necessary to design a Raychem XL-Trace
More informationElectrical cable Water supply tube Fittings for tube Coupler Teflon tape. Hole saw min. 2½" bit
Installation Parts and Tools Parts not Provided Electrical cable Water supply tube Fittings for tube Coupler Teflon tape Air gap Wire nuts for 6-gauge wiring Hose clamp ⅞" UL approved strain relief Electrical
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FCB Pinnacle 4 Flavor Wide Body Units Thermostat Reset Upgrade Kit P/N 629088712 Release Date: January 23, 2006 Publication Number: 629088712INS Revision Date: March 24, 2014
More informationIMPORTANT SAFETY INSTRUCTIONS:
PRODUCT NAME: Hadley 4 Light Pendant ITEM NUMBER: LC813 DIMENSIONS OF ITEM ASSEMBLED: Small: 18 1/2 H x 11 Square Large: 25 H x 16 Square IMPORTANT SAFETY INSTRUCTIONS: -A licensed professional electrician
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The ALT-LPM Power Connection Kit without Enclosure is constructed of cast aluminum for use with all versions of Nelson Heat Tracing Systems LT, HLT & NC heater cables. Compatible for use with
More informationInstallation Procedure for D-200 series Shielded Cable Splice Kits with MiniSeal Crimp Primary Splices
. Page: Page 1 of 7 Installation Procedure for D-200 series Shielded Cable Splice Kits with MiniSeal Crimp Primary Splices 1.0 Scope This standard contains the procedures for making environment resistant
More informationHE280 Assembly. SeeMeCNC Guides. HE280 Assembly. Assembly of the HE280. Written By: JJ Johnson seemecnc.dozuki.
SeeMeCNC Guides HE280 Assembly Assembly of the HE280. Written By: JJ Johnson 2017 seemecnc.dozuki.com/ Page 1 of 51 TOOLS: Phillips Screwdriver, size P1 (1) small flat blade screwdriver (1) 1/4" or 6mm
More informationKE-Series Constant-Wattage Heating Cable
KE-Series Constant-Wattage Heating Cable Installation Instructions Read and understand this material before installing this heater. Failure to understand how to safely install the heater could result in
More informationModular Sensing Cable Installation Instructions
TraceTek TT1000 Modular Sensing Cable Installation Instructions General Information These instructions explain the proper procedures for installing and testing TT1000 modular sensing cables, and provide
More informationInstallation & Service Manual. Models ALF 20, 30, 40, 50, 60, 80
Installation & Service Manual Models ALF 20, 30, 40, 50, 60, 80 IMPORTANT! Read all safety instructions before installing, using, or servicing the heater. Installation & servicing should only be carried
More informationJOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30)
P. 1 of 12 JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30) Item: Qty: Description: 1 2 1 x 1 x 5/8 Tee Fitting 2 2 Plastic Snap-in Hose Grommet 3 4 1-1/2" Hose Clamps
More informationTable of Contents. What to Expect with. Mounting Options. Tools Needed
Table of Contents www.hunterfan.com What to Expect with Your Installation Congratulations on purchasing your new Hunter ceiling fan! It will provide comfort and performance in your home or office for many
More informationBF5000NT BF5000 EF2604 SF2603 DF2603
PARTS & SERVICE MANUAL FOR THE 26 FIREPLACE MODEL NUMBER: BF5000NT BF5000 EF2604 SF2603 DF2603 7400520000R03 TABLE OF CONTENTS Table of Contents OPERATION... 2 EXPLODED DIAGRAM... 4 WIRING DIAGRAM... 5
More informationINSTALLATION INSTRUCTIONS
Page 1 INSTALLATION INSTRUCTIONS DEKORON / UNITHERM ELECTRIC TRACED BUNDLES, HEATED HOSES, HYBRID BUNDLES, AND PROBE SUPPORT BUNDLES FOR CEM APPLICATIONS Form INSTCEM040103 This bulletin provides the Field
More informationFreezer Frost Heave Prevention
Freezer Frost Heave Prevention 1. Pipe Freeze Protection and Flow Maintenance RaySol System Mineral Insulated Heating Cable System This step-by-step design guide provides the tools necessary to design
More informationInstallation Instructions. For the 18 Built-In Dishwasher and Front Color Panels
Installation Instructions For the 18 Built-In Dishwasher and Front Color Panels Printed in USA 154232102 Before You Begin DO NOT INSTALL DISHWASHER UNTIL YOU HAVE READ ALL INSTRUCTIONS. FOR YOUR SAFETY,
More informationXL-Trace System. Installation and Operation manual for pipe freeze protection and flow maintenance
XL-Trace System Installation and Operation manual for pipe freeze protection and flow maintenance Thermal management WWW.PENTAIRTHERMAL.COM Important Safeguards and Warnings WARNING: FIRE AND SHOCK HAZARD.
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The D1CMD Class I Div. 1 Continuity Monitor Device provides the cable termination and explosion proof seal parts needed to make the power end electrical connections associated with Nelson Heat
More informationNGC-40-IO Control and monitoring modules for use with the Raychem NGC-40 system Installation Instructions
NGC-40-IO Control and moniting modules f use with the Raychem NGC-40 system Installation Instructions A DESCRIPTION The NGC-40-IO provides up to four additional RTD inputs. These additional RTD inputs
More informationAir Conditioner. user installation & manual manual. imagine the possibilities
ARFSSSBWK Series ARFSSSCUR AJ JNADCH Series Air Conditioner user installation & manual manual This manual is made with 100% recycled paper. imagine the possibilities Thank you for purchasing this Samsung
More informationCommercial and Residential Self-Regulating Heating Products
Commercial and Residential Self-Regulating Heating Products Application and Design Guide H53585 (800) 545-6258 www.tycothermal.com Table of Contents Introduction 1 Heating Cables Selection Guide 1 Product
More informationHalf Inch Round LED Rope Light
11235 West Bernardo Court, Suite 102 San Diego, CA 92127 888-880-1880 Fax: 707-281-0567 EnvironmentalLights.com Half Inch Round LED Rope Light LED Rope light is a beautiful and versatile way to light any
More informationSMPG3 SNOW MELTING AND DE-ICING POWER DISTRIBUTION AND CONTROL PANEL. For three-phase heating cables PRODUCT OVERVIEW
SNOW MELTING AND DE-ICING POWER DISTRIBUTION AND CONTROL PANEL For three-phase heating cables Mounting brackets Nameplate HTC energized light Power on light Heater cycle timed control Heater (3R only)
More informationSERGE BARIL HEAT TRACING SYSTEMS
DESCRIPTION The HA-P Hazardous Area Seal Kit provides the cable termination and explosion proof seal parts needed to make the power end electrical connections associated with Serge Baril Heat Tracing Systems
More informationIMPORTANT SAFETY INFORMATION
Service Manual Model Number: DF2000 UL Part Number 690889XXXX IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to service this fireplace. For your safety, always comply with
More informationINSTALLATION INSTRUCTIONS UNDERCOUNTER DISHWASHERS
INSTALLATION INSTRUCTIONS UNDERCOUNTER DISHWASHERS VIKING 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 IMPORTANT - PLEASE READ AND FOLLOW Before beginning - please read these instructions
More informationGardian W51. Approvals
Gardian W51 120 V pre-assembled electric heating cables for pipe freeze protection and roof & gutter de-icing Installation Instructions Description Gardian W51 120 V pre-assembled self-regulating heating
More informationSkin-Effect Heat-Tracing System (STS)
Skin-Effect Heat-Tracing System (STS) INDUSTRIAL HEAT TRACING SOLUTIONS WWW.pentairthermal.com Cairn India ENGINEERED SOLUTIONS Pentair Industrial Heat Tracing Solutions offers innovative integrated technologies
More informationTraceTek Sensing Module Installation, Operation and Maintenance Instructions DESCRIPTION SPECIFICATIONS APPROVALS TYPE NM
TTC-1 TraceTek Sensing Module Installation, Operation and Maintenance Instructions DESCRIPTION The nvent RAYCHEM TraceTek TTC-1 sensing module is used with TraceTek sensing cables to detect liquid leaks.
More information52 CEILING FAN READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V.
Irene 52 CEILING FAN READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V. 60Hz TABLE OF CONTENTS Tools and Materials Required... 1 Package Contents... 1 Safety Rules... 2 Mounting Options... 3 Hanging
More informationTable of Contents. What to Expect with. Mounting Options. Tools Needed. Preparation. Wiring. Downrod.
Table of Contents www.casablancafanco.com What to Expect with Your Installation Congratulations on purchasing your new Casablanca ceiling fan! It will provide comfort and performance in your home or office
More informationFor Raychem ACS-30 Controls Systems
ACS-30 Protocol Interface Mapping For Raychem ACS-30 Controls Systems Firmware Version 5.05 THERMAL BUILDING SOLUTIONS EN-RaychemACS30-AR-H58324 03/16 Table of Content Section 1. Introduction... 3 1.1
More informationHeat Tracing Sales Mt. Airy, Maryland Heating Cable. Cut to Length in Field. Description
Self-Regulating Protection D E C B A Self-Regulating, Energy Efficient Designed for Protection Max. Exposure Temp. 185 F (Power Off) Cost Effective for Commercial Construction Protection Applications Protection
More informationManual No: Revision: D. Sump Sensor. Installation Guide
Manual No: 576013-301 Revision: D Sump Sensor Installation Guide Notice Veeder-Root makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranties
More informationALUMA INSTRUCTION MANUAL WARRANTY CERTIFICATE
ALUMA BY INSTRUCTION MANUAL WARRANTY CERTIFICATE Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright laws. The Minka-Aire
More informationTT3000 and TT5000 Series
TT3000 and TT5000 Series Modular Sensing Cables Installation Instructions GENERAL INFORMATION COMPLETE BILL OF MATERIALS Before beginning installation, confirm there is a plan for the leak detection system
More informationI<enmore Elite. instructions dlnstallation. Installation Guide Instrucciones de Instalaci6n. English / Espafiol/Frangais
Installation Guide Instrucciones de Instalaci6n instructions dlnstallation English / Espafiol/Frangais Models/Modelos/Mod_les: 630.1390% 630.1 391_ I
More information