ASPEC Positive Pressure Manifold. User's Guide

Size: px
Start display at page:

Download "ASPEC Positive Pressure Manifold. User's Guide"

Transcription

1 ASPEC Positive Pressure Manifold User's Guide

2 This Page Is Intentionally Left Blank

3 Gilson, Inc. All rights reserved. All product and/or company names are trademarks of their respective holders. Use of the trademark(s) in this document does not imply any affiliation with or endorsements by the trademark holder(s).

4 CONTENTS CONTENTS Safety 6 Symbols, Signs, and Notices 6 Chemical Hazards 7 Flammable Solvents 7 Replacement Parts 7 Signs of Damage 7 Site Requirements 7 Storage and Movement 7 Sécurité 8 Symboles et Notes 8 Risques Chimiques 9 Solvants Inflammables 9 Pièces de Remplacement 9 Signes de Détérioration 9 Exigences du Site 9 Stockage et Déplacement 9 Introduction 10 Description 10 Technical Specifications 19 Setup 20 Set up or Replace the Manifold 20 Connect the Gas Supply 21 4 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

5 Operation 22 Setup for Flow to Waste 22 Setup for Flow to Collection 23 Seat the Manifold 24 Unseat the Manifold 24 Control the Flow 25 General Flow Guidelines 27 Basic SPE Technique 28 Maintenance 31 Clean the ASPEC PPM 31 Install or Replace the O-Ring 31 Replace the Manifold Gasket 31 Maintenance Parts 31 Troubleshooting Table 32 Repair and Return Policies 36 Before Calling Us 36 Warranty Repair 36 Non-Warranty Repair 36 Return Procedure 37 Unit End-of-Life 37 Replacement Parts and Accessories 38 Configuration Kits 39 ASPEC Positive Pressure Unit 39 CONTENTS ASPEC Positive Pressure Manifold User's Guide 5

6 Safety Safety Read this section before installing and operating the instrument. Only trained technical personnel in a laboratory environment may use the instrument for non-medical, liquid handling purposes. For safe and correct use of the instrument, operating and service personnel must follow all instructions contained in this guide when installing, cleaning, and maintaining the instrument. All safety precautions must be observed during all phases of operation, service, and repair of the instrument. Failure to comply with these precautions or with warnings described in the user s guide violates safety standards of design, manufacture, and intended use of the instrument. Gilson assumes no liability for customers failing to comply with these requirements. Refer to the rear panel label on the instrument for the current standards to which the instrument has been found compliant. Read all documentation and safety information for accessories, peripherals, and other instruments that may be used with this instrument before operating the system. Symbols, Signs, and Notices Safety Notices The following safety notices may appear in this document: WARNING Indicates a potentially hazardous situation which, if not avoided, may result in personal injury. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. NOTICE Indicates a potentially hazardous situation which, if not avoided, may result in equipment damage. 6 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

7 Hazard Symbols The following hazard symbol may appear on the instrument or in this document: Symbol Explanation Explication Erläuterung Chemical Hazards Caution Attention Vorsicht Any chemicals used for analysis should be handled according to good laboratory practice (GLP). They should also be stored, used, and disposed of in accordance with the manufacturer s specifications, as well as local and national regulations. Potentially hazardous chemicals can be used with the instrument. Use care when handling chemicals and wear appropriate personal protective equipment (PPE), such as safety glasses, gloves, etc. The responsible individual must ensure that personnel are not exposed to hazardous levels of toxic substances as outlined in the material safety data sheets (MSDSs), or any documentation provided by local governing bodies such as The Health Protection Agency (United Kingdom) or The Occupational Safety and Health Administration (United States). Flammable Solvents Secure all flammable solvents. The temperature of liquids inside the system must be 25 C (77 F) below the lowest flame temperature of any solvents used. Replacement Parts Be sure to use only replacement parts mentioned in this user s guide. Refer to Replacement Parts and Accessories on page 38. Signs of Damage Do not attempt to use the instrument if there are visible signs of damage. Site Requirements Do not operate the instrument if site conditions are not within specifications. Refer to Technical Specifications on page 19 for more details. Storage and Movement Empty the drain well before moving the instrument. Safety ASPEC Positive Pressure Manifold User's Guide 7

8 Sécurité Sécurité Veuillez lire attentivement ce paragraphe avant toute installation ou utilisation de l instrument. Cet instrument est exclusivement destiné à être utilisé dans un environnement de laboratoire, par un personnel qualifié, à des fins de manipulations de liquides nonmédicales. Pour une utilisation correcte et en toute sécurité de l instrument, il est nécessaire que le personnel qui utilise et réalise la maintenance de l instrument, suive les instructions contenues dans ce guide lors de l installation, du nettoyage et de la maintenance de l instrument. Toutes les consignes de sécurité doivent être respectées durant toutes les phases de fonctionnement, d entretien ou de réparation de l instrument. Le non-respect de ces précautions ou des avertissements spécifiques mentionnés dans ce guide compromet les normes de sécurité de conception, de fabrication et d utilisation prévue de l instrument. Gilson décline toute responsabilité en cas d incapacité du client à se conformer à ces exigences. Merci de vous reporter aux indications mentionnées sur le panneau arrière de l instrument pour connaître les normes auxquelles l instrument a été déclaré conforme. Veuillez lire toute la documentation et les informations relatives à la sécurité pour les accessoires, périphériques, et autres instruments pouvant être utilisés avec cet instrument avant de faire fonctionner le système. Symboles et Notes Notes de Sécurité Les notes de sécurité suivantes peuvent apparaître dans ce document: AVERTISSEMENT Une situation potentiellement dangereuse qui, si elle n est pas évitée, peut entraîner des dommages corporels. ATTENTION Une situation potentiellement dangereuse qui, si elle n est pas évitée, peut entraîner des blessures mineures ou légères. AVIS Une situation potentiellement dangereuse qui, si elle n est pas évitée, peut entraîner des dommages matériels. 8 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

9 Symbole de Dangers Le symbole de dangers suivants peuvent apparaître sur l instrument ou dans ce document: Symbol Explanation Explication Erläuterung Risques Chimiques Caution Attention Vorsicht Tous les produits chimiques utilisés pour l analyse doivent être manipulés conformément aux bonnes pratiques de laboratoire (BPL). Ils doivent être stockés, utilisés et éliminés conformément aux recommandations du fabricant ainsi qu aux réglementations locales et nationales. Manipuler les produits chimiques avec précaution et porter un équipement de protection individuelle adapté (EPI) comme des lunettes de sécurité, des gants, etc. Le responsable doit veiller à ce que le personnel ne soit pas exposé à des niveaux dangereux de substances toxiques comme indiqué dans les fiches de données de sécurité (fds), ou toute documentation fournie par les instances locales telles que l agence de protection de la santé (Royaume-Uni) ou l administration de la sécurité et de la Santé (Etats-Unis). Solvants Inflammables Prendre garde aux solvants inflammables. La température des solvants à l intérieur du système doit impérativement être inférieure de 25 C à la température de flamme la plus basse des solvants utilisés. Pièces de Remplacement Utiliser exclusivement les pièces détachées mentionnées dans ce guide utilisateur. Faire référence aux Replacement Parts and Accessories on page 38. Signes de Détérioration Ne pas utiliser le système en cas de signes de détérioration visibles. Exigences du Site Ne pas faire fonctionner l instrument si le site présente des conditions non conformes aux spécifications. Faire référence aux Technical Specifications on page 19. Stockage et Déplacement Vider le conteneur d evacuation des solvants usages avant de deplacer l appareil. Sécurité ASPEC Positive Pressure Manifold User's Guide 9

10 Introduction Introduction Description The ASPEC Positive Pressure Manifold provides uniform and consistent flow rate control for the cleanup of low or high viscosity samples, improves solid-phase extraction (SPE) reproducibility and recovery. The ASPEC PPM incorporates easily into laboratory workflows and provides a fast and simple way to prepare several samples for later analysis by chromatography. The ASPEC manifold offers a cost-effective approach to automation for environmental, clinical, forensic, and food or beverage testing laboratories. It is also an ideal choice for SPE cleanup prior to LCMS for bioanalyses. Safety Shield Protects users from solvents. Drain Well Refer to page 12 for a detailed description. SPE Racks 15-, 24-, and 96-positions available. SPE Collection Racks 15-, 24-, and 96-positions available. Manifold Locking Lever Forms the seal between the manifold and SPE cartridge when locked. Refer to page 14. Process Control Dial Switch between SPE and Dry controls to adjust gas flow. Refer to page 12 for more information. Pressure Gauge Monitors the operating pressure of the system, which should not exceed 15 psi. SPE Control Dial Switch between Low Flow and High Flow when the process control dial is set to SPE. Refer to page 12 for a detailed description. Figure 1 Standard Components of the ASPEC Positive Pressure Manifold (Left View) 10 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

11 Manifold Retaining Clip Holds the manifold in place. Refer to page 20. Locator Plate Refer to page 14 for a detailed description. Thumbscrews Manifold Available in three configurations: 15- or 24-cartridge holders and 96-well plate holders. Manifold Positioning Lever Raises and lowers the manifold over the SPE cartridge holder. The manifold locking level must be unlocked to move this lever. Refer to page 14. Introduction Low Flow Adjustment Knob Used to fine tune flow when Low Flow is selected on the SPE control dial. Refer to page 13. Flow Adjustment Locks Used to lock in flow adjustments made with the low and high flow regulator knobs. Refer to page 13. High Flow Adjustment Knob Used to fine tune flow when High Flow is selected on the SPE control dial. Refer to page 13. Figure 2 Standard Components of the ASPEC Positive Pressure Manifold without Shield ASPEC Positive Pressure Manifold User's Guide 11

12 Introduction Control Dials Process Control Dial Used to select SPE (activates the SPE control dial to control high or low flow) or Dry (maximum flow). SPE Control Dial Used to select Low Flow, High Flow, or Off (to stop flow) when the process control dial is set to SPE. Drain Well Used primarily to flow the preparation solvents and matrix to waste. Ensure that the waste outlet tubing flows to a large waste container. Waste Outlet Tubing Rear Barbed Fitting Figure 3 Process Control Dial Figure 4 SPE Control Dial Figure 5 Collection and Drain Well with Waste Outlet Tubing Front Ejection Plate Used to quickly eject all the SPE cartridges from the cartridge rack. Slide the ejector plate through the standoffs on the SPE cartridge rack, and then push the plate up to eject the SPE cartridges. SPE Cartridges Standoffs Ejector Plate Figure 6 Ejecting SPE Cartridges 12 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

13 Flow Adjustment Knobs Used to fine tune flow when Low Flow or High Flow is selected on the SPE control dial. Turn the adjustment knobs clockwise to open the valve and begin flow or to increase flow. Turn the adjustment knobs counterclockwise to decrease flow or to close the valve and stop flow. NOTE The loss of tension in the adjustment knobs indicates that the valve is fully closed. Flow Adjustment Locks Used to lock in flow adjustments made with the low and high flow adjustment knobs. Turn the flow adjustment locks clockwise to lock the low or high flow adjustment knobs. Turn the flow adjustment locks counterclockwise to unlock the low or high flow adjustment knobs. Introduction Flow Adjustment Locks High Flow Adjustment Knob Low Flow Adjustment Knob Figure 7 Low and High Flow Adjustment Knobs and Locks ASPEC Positive Pressure Manifold User's Guide 13

14 Introduction Locator Plate The front position of the locator plate is used as the active position, whereas the rear position accommodates the drain well when not in use. Manifold Locking Lever Forms the seal between the manifold and SPE cartridge holder when locked. Push the lever back to unlock (Red Lock Symbol, unlocked), and pull the lever forward to lock (Green Lock Symbol, locked). Manifold Positioning Lever Raises and lowers the manifold over the SPE cartridge holder. The manifold locking lever must be unlocked to move this lever. Push the lever back to lower the manifold (toward the Down position), and pull the lever forward to raise the manifold (toward the Up position). Rear (Unlocked) Front (Locked) Front Position Rear Position Figure 8 Locator Plate on the ASPEC PPM Front (Up) Rear (Down) Figure 10 Manifold Positioning Lever Figure 9 Manifold Locking Lever 14 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

15 Pressure Gauge Monitors the operating pressure of the system, which should not exceed 15 psi. Figure 11 Pressure Gauge SPE Cartridge Plugs (Optional) Used to fill empty positions in the SPE cartridge racks (15- and 24-position). Introduction Plugs Rear Rows Empty Position SPE Cartridges (Front Row) Figure 12 Plugs on 24-Position Rack ASPEC Positive Pressure Manifold User's Guide 15

16 Introduction Unpacking The ASPEC Positive Pressure Manifold is delivered as a base unit (along with the safety shield) with one or more configuration kits for: 96 well SPE microplates (PN ), 15-position SPE cartridge racks (6 ml, PN ), and 24-position SPE cartridge racks (1 ml, PN or 3 ml, PN ). To safely remove the ASPEC PPM and accessories: 1. Open the top of the shipping container. 2. Remove the packing slip and bag containing the documentation, which will include: a printed user s guide, USB drive with video, items included checklist, and a quality control checklist. 3. Read the user s guide. 4. Remove the box containing the standard equipment and accessory kit, and then set it aside. 5. Check that all items specific to the configuration ordered and listed in Standard Equipment on page 17 are present. 6. Remove the safety shield nested in the foam, and then set it aside. 7. Grab the base of the ASPEC PPM firmly with two hands on opposing sides, and gently lift the ASPEC PPM out of the shipping box, and then set it on a laboratory bench that meets the site requirements on page 19. NOTE The ASPEC PPM ships and is nested within four molded foam pieces: two on the front and two on the back. Do not grip the ASPEC PPM by the manifold carrier or by the levers. 8. Hold the base of the ASPEC PPM, and then gently slide the molded foam pieces away from the base. 16 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

17 Standard Equipment The following items are considered standard equipment and are provided with the ASPEC PPM. For part numbers, refer to Replacement Parts and Accessories on page 38. All Configurations Drain well (qty. 1) Gas supply tubing, 1/4" (OD), (qty. 1) Locator plate, dual position (qty. 1) O-ring manifold seal (qty. 1) Safety shield (qty. 1) Waste outlet tubing, Tygon 0.25" (OD), 3 ft. (qty. 1) Documentation ASPEC Positive Pressure Manifold User s Guide (qty. 1) USB drive with video of a sample protocol (qty. 1) Configuration Kit: 96-Position SPE Manifold Kit (PN ) Gasket with adhesive-backed seal, 96-position (qty. 2) Manifold, SPE, 96-position (qty. 1) O-ring manifold seal (qty. 1) SPE plate adapter (qty. 1) 15-Position SPE Manifold Kit (6 ml, PN ) Cartridge rack, SPE, 15-positions, 6 ml (qty. 1) Ejection plate for SPE cartridges (qty. 1) Gasket with adhesive-backed seal, 15-positions (qty. 2) Manifold, SPE, 15-positions (qty. 1) O-ring manifold seal (qty. 1) Tube rack for SPE collection, 6 ml (qty. 1) Introduction ASPEC Positive Pressure Manifold User's Guide 17

18 Introduction 24-Position SPE Manifold Kit (1 ml, PN ) Cartridge ejection plate (qty. 1) Cartridge rack, SPE, 24-positions, 1 ml (qty. 1) Gasket with adhesive-backed seal, 24-positions (qty. 2) Manifold, SPE, 24-positions (qty. 1) O-ring manifold seal (qty. 1) Tube rack, SPE collection, 1 3 ml, 12 x 75 mm (qty. 1) 24-Position SPE Manifold Kit (3 ml, PN ) Cartridge ejection plate (qty. 1) Cartridge rack, SPE, 24-positions, 3 ml (qty. 1) Gasket with adhesive-backed seal, 24-positions (qty. 2) Manifold, SPE, 24-positions (qty. 1) O-ring manifold seal (qty. 1) Tube rack, SPE collection, 1 3 ml, 12 x 75 mm (qty. 1) Recommended Accessories All Configurations Gas pressure regulator, 15 psi, external (qty. 1) 96-Position Microplate for SPE collection, 96-position, 1 ml (qty. 10) Microplate for SPE collection, 96-position, 2 ml (qty. 10) 15-Position Plugs to fill empty SPE cartridge spaces, 6 ml (qty. 15) Tubes, glass, collection, 10 ml, 15 x 85 mm (qty. 250) 24-Position Plugs to fill empty SPE cartridge spaces, 1 ml (qty. 24) Plugs to fill empty SPE cartridge spaces, 3 ml (qty. 24) Tubes, glass, collection, 5 ml, 12 x 17 mm (qty. 250) 18 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

19 Technical Specifications Specification Dimensions (W x D x H) Liquid contact materials Site requirements Weight Description 33 x 48.3 x 44.2 cm (13 x 19 x 17.4 in.) Description Gasket Locator plate Specification Environment Inert gas supply kg (32 lbs.) Material Neoprene Ertalyte Definition Indoor use only. If using volatile solvents, use a vent hood. Maximum pressure of 15 psi. Use 1/4" (OD) tubing. Introduction ASPEC Positive Pressure Manifold User's Guide 19

20 Setup Setup Set up or Replace the Manifold 1. Pull the manifold positioning lever forward (toward the Up position) until the manifold is fully raised. 2. Remove the manifold shield covering the manifold carrier, and then set it aside. 3. Turn (but do not remove) the thumbscrews counterclockwise to free the manifold retaining clip. Set the manifold retaining clip aside. 4. If necessary, remove the pre-installed manifold. NOTE Ensure that the O-ring does not fall out while removing the manifold. 5. Slide the new manifold into the manifold carrier with the orange O-ring on the back of the manifold facing the rear. 6. Reinstall the manifold retaining clip. 7. Turn the thumbscrews clockwise until finger tight. 8. Replace the manifold shield, and ensure that the standoff screws are seated properly on the manifold carrier. Manifold Shield Thumbscrews Manifold Carrier Manifold Manifold Retaining Clip Figure 13 Exploded View of Shield and Manifold Carrier 20 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

21 Connect the Gas Supply 1. Locate the gas tubing supplied in the accessory kit. Connect the tubing from the rear quick connect port on the manifold to the quick connect port on the upper right side on the rear of the ASPEC PPM. Setup Plunger Insert Gas Tubing Figure 14 Gas Supply Connection (Rear View) Figure 15 Quick Connect Port with Tubing 2. Insert the gas wall supply tubing (1/4" OD, not provided) into the Gas Inlet quick connect port on the back of the instrument. NOTE The orange plunger insert will automatically engage the tubing. Pull back the tubing to check for proper engagement. Depress the orange plunger insert to release the tubing. NOTICE Ensure that the process control dial is set to Dry and the SPE control dial is set to Off before connecting the gas supply. Do not exceed 15 psi inlet pressure. 3. Use an external regulator to slowly increase pressure to the system up to 15 psi. 4. Switch the process control dial to SPE. ASPEC Positive Pressure Manifold User's Guide 21

22 Operation Operation Ensure that the following conditions are met before operating the ASPEC PPM: The SPE control dial is set to Off. The process control dial is set to SPE. The low and high flow adjustment knobs are closed. Refer to Flow Adjustment Knobs on page 13. The gas supply connection and regulator are properly installed. Refer to Connect the Gas Supply on page 21. Setup for Flow to Waste 1. Slide the locator plate to the front of the locator bed. 2. Place the drain well on the front position of the locator plate. 3. Connect the waste outlet tubing to the barbed fitting on the back of the collection and drain well. 4. Set the appropriate SPE cartridge rack with cartridges on the drain well. Waste Outlet Tubing SPE Cartridge Rack (24-Position) Collection and Drain Well Barbed Fitting Locator Plate (Rear) Figure 16 Flow to Waste Setup NOTE If your experiment does not require the full use of the 15- or 24-position rack, use plugs to fill the empty spaces. Refer to SPE Cartridge Plugs (Optional) on page USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

23 Setup for Flow to Collection 96-Position 1. Slide the locator plate to the front of the locator bed. 2. Move the drain well to the rear position of the locator plate. 3. Place the 96-position well plate on the front position of the locator plate. 4. Set the plate spacer on the 96-position well plate. 5. Set the appropriate SPE plate on the plate spacer. 15- or 24-Position 1. Slide the locator plate to the front of the locator bed. 2. Move the drain well to the rear position of the locator plate. 3. Place the 15- or 24 position tube rack with tubes on the front position of the locator plate. Locator Plate SPE Cartridge Rack (96-Position) Plate Spacer Collection and Drain Well Rear Figure 17 Flow to Collection Setup (96-Position) SPE Cartridge Rack (24-Position) Collection Tubes and Tube Rack 96-Position Well Plate Figure 18 Flow to Collection Setup (24-Position) (15-Position SPE Rack Not Shown) Front Operation 4. Set the appropriate 15- or 24-position SPE cartridge rack on the tube rack assembly. NOTE If your experiment does not require the full use of the 15- or 24-position rack, use plugs to fill the empty spaces. Refer to SPE Cartridge Plugs (Optional) on page 15. ASPEC Positive Pressure Manifold User's Guide 23

24 Operation Seat the Manifold 1. Push the manifold locking lever back to the fully unlocked position (Red Lock Symbol, unlocked). 2. Pull the manifold positioning lever forward to the fully raised position (toward the Up position). 3. Slide the locator plate back so that the SPE cartridges are directly below the manifold. NOTICE If you encounter interference with the safety shield, remove, and then replace the shield after positioning the locator plate. 4. Slowly push the manifold positioning lever back to lower the manifold (toward the Down position) until the manifold makes contact with the tops of the SPE cartridges. Rear Figure 19 Manifold Locking Lever Front Front 5. Pull the manifold locking lever forward to the fully locked position (Green Lock Symbol, locked) to create a seal between the manifold and the SPE cartridges. Rear Figure 20 Manifold Positioning Lever NOTICE Do not use the manifold positioning lever to tighten the seal. If the plate does not seat properly, unlock the manifold with the manifold locking lever, and then raise the manifold slightly with the manifold positioning lever. Repeat steps 1 through 5. Unseat the Manifold 1. Push the manifold locking lever back to the fully unlocked position (Red Lock Symbol, unlocked). 2. Pull the manifold positioning lever forward to the fully raised position (toward the Up position). 3. Slide the locator plate forward to the front of the locator bed. 24 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

25 Control the Flow The ASPEC PPM features three different gas pressure controls (low flow, high flow, and dry) with fine tune adjustments available for low and high flow. The following provides a basic overview of control options. For step-bystep instructions, refer to page 28. Process Control Dial Low Flow Adjustment Knob Flow Adjustment Locks SPE Control Dial High Flow Adjustment Knob Operation Figure 21 Flow Controls Overview Flow Adjustment 1. Turn the adjustment knobs clockwise to open the valve and increase flow. 2. Turn the adjustment knobs counterclockwise to reduce flow and close the valve. The loss of tension in the adjustment knobs indicates that the valve is fully closed. High Flow Recommended for SPE cartridge wetting during conditioning and for washing. To turn on high flow: 1. Switch the process control dial to SPE. 2. Switch the SPE control dial to High Flow. 3. Turn the high flow adjustment knob clockwise until the flow reaches 4 to 5 drops per second. 4. To turn off high flow, switch the SPE control dial to Off. ASPEC Positive Pressure Manifold User's Guide 25

26 Operation Low Flow Recommended for conditioning (after initial SPE cartridge wetting with high flow), sample loading, and elution. To turn on low flow: 1. Switch the process control dial to SPE. 2. Switch the SPE control dial to Low Flow. 3. Turn the low flow adjustment knob clockwise until the flow reaches 1 to 2 drops per second. 4. To turn off low flow, switch the SPE control dial to Off. Dry Recommended for drying the SPE cartridges with maximum flow. To turn on the dry setting: 1. Ensure the SPE control dial is switched to Off. 2. Switch the process control dial to Dry. 3. To turn off the dry setting, switch the process control dial to SPE. NOTICE Turn off the manifold between process steps. Shut off the external gas supply when the manifold is not in use. Disconnect the manifold from the gas supply when storing the machine. 26 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

27 General Flow Guidelines The following table provides general process and flow guidelines. Table 1 SPE Process and Control Guidelines for SPE Steps SPE Steps NOTE Process Control Setting SPE Control Setting For all low and high flow recommendations, refer to the SPE Format Flow Guidelines table below. Condition SPE High Flow, and then switch to Low Flow Load SPE Low Flow, based on viscosity Wash SPE High Flow, based on viscosity Dry Dry Off Elute SPE Low Flow, based on viscosity Operation Table 2 SPE Format Flow Guidelines SPE Format High Flow (drops per second) 6 ml 3 to 5 1 Low Flow (drops per second) 3 ml 1 1 drop per 2 to 3 seconds 1 ml microplate 0.5 to 1 1 drop per 3 to 4 seconds ASPEC Positive Pressure Manifold User's Guide 27

28 Basic SPE Technique Operation 1. Ensure that the necessary conditions for operation are met. Refer to page Follow the instructions to Setup for Flow to Waste on page 22. Initial Condition Step 3. Pipette the appropriate volume of conditioning solvent into each available SPE cartridge. 4. Seat the manifold. Refer to Seat the Manifold on page Switch the SPE control dial to High Flow. 6. Turn the high flow adjustment knob clockwise until the desired flow rate is achieved. 7. When the solvent levels decrease to 2 mm above the fastest eluting cartridge of any one of the SPE cartridge/s, quickly switch the SPE control dial to Low Flow. Top Frit SPE Sorbent Bottom Frit Figure 22 SPE Cartridge Diagram 8. Turn the low flow adjustment knob clockwise until the flow slowly restarts. 9. When the solvent levels lower to the top frits of all of the SPE cartridges, quickly switch the SPE control dial to Off. Allow the solvent to return to atmospheric pressure. NOTE In some cases, positive pressure can remain in the SPE cartridges, even after the SPE control dial has been set to Off. Unseat the manifold to stop unwanted flow. Refer to page USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

29 Additional Condition Steps 10. Unseat the manifold. Refer to page Repeat steps 3 through 9 for the appropriate number of conditioning steps. NOTE Sample Load Steps If using an identical solvent for subsequent conditioning steps, use the flow adjustment locks to ensure the same pressure values are used. 12. Pipette the appropriate volume of sample into each available SPE cartridge. 13. Seat the manifold. Refer to page Switch the SPE control dial to Low Flow. 15. Turn the low flow adjustment knob clockwise until the desired flow rate is achieved. 16. When the sample stops dripping from the SPE cartridges, turn the SPE control dial to Off. 17. Unseat the manifold. Refer to page 24. Wash Steps 18. Pipette the appropriate volume of washing solvent into each available SPE cartridge. 19. Seat the manifold. Refer to page Switch the SPE control dial to High Flow. 21. Turn the high flow adjustment knob clockwise until the desired flow rate is achieved. 22. When the washing solvent stops dripping from the SPE cartridges, turn the SPE control dial to Off. 23. Unseat the manifold. Refer to page Repeat steps 18 through 23 for the appropriate number of washing steps. Operation ASPEC Positive Pressure Manifold User's Guide 29

30 Operation Dry Steps 25. Switch the process control dial to Dry. 26. When the solvent stops dripping from the SPE cartridges, wait an additional 10 seconds, and then switch the process control dial to SPE. 27. Unseat the manifold. Refer to page 24. Elution Steps 28. Follow the instructions to Setup for Flow to Collection on page Pipette the appropriate volume of eluent into each available SPE cartridge. 30. Switch the SPE control dial to Low Flow. 31. Turn the low flow adjustment knob clockwise until the desired flow rate is achieved. 32. When the eluate stops dripping from the SPE cartridges, turn the SPE control dial to Off. 33. Repeat steps 28 through 32 for the appropriate number of elution steps. 34. If needed, add additional dry steps. Final Steps 35. Eject the SPE cartridges. Refer to Ejection Plate on page Follow all necessary maintenance procedures after operation is complete. Refer to Maintenance on page USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

31 Maintenance Clean the ASPEC PPM The instrument should be cleaned occasionally, using a dry, clean cloth. If necessary, use a cloth dipped in soapy water. If liquid is accidentally spilled on the instrument, wipe it up immediately. Install or Replace the O-Ring 1. Remove the manifold from the manifold carrier. 2. Gently remove the O-ring from the rear of the manifold with your fingers. If necessary, free the O-ring with a flathead screwdriver. 3. Insert a new O-ring into the circular depression in the rear of the manifold. Replace the Manifold Gasket 1. Remove the manifold from the manifold carrier. 2. Set the manifold down with the gasket facing up. 3. Peel the gasket away, starting from the corner. Discard the gasket. 4. Clean off any excess adhesive from the manifold using methanol. 5. Locate the replacement gasket. 6. Peel away the adhesive backing on the new gasket, starting from the corner. Discard the backing material. 7. Align the new gasket with the four corners of the manifold before attaching the gasket with the adhesive side facing down. Maintenance Parts Description Part Number Gasket, 96-position for SPE manifold (qty. 10) Gasket, 24-position for SPE manifold (qty. 10) Gasket, 15-position for SPE manifold (qty. 10) O-ring for manifold seal (qty. 5) Maintenance ASPEC Positive Pressure Manifold User's Guide 31

32 Troubleshooting Table Symptoms Possible Causes SPE Steps Solutions No inlet pressure. Check that the gas pressure source is set to 15 psi. Troubleshooting Table Lack of flow Liquid flows unevenly O-ring damaged or missing. Replace the O-ring. Refer to page 31. All Damaged process control dial. Channeling inside the sorbent of the SPE cartridge/s. Clogged SPE cartridge/s. Condition Condition Load Replace the front panel. Contact your local Gilson representative. Refer to page 36. Specific Causes Drying of the cartridge/s. Insufficient condition volume. Excessive flow rate. Replace the SPE cartridge/s. Specific Solutions Repeat the condition step. Increase the condition volume. Reduce the flow rate. Reconsider the sample preparation workflow; e.g., sample filtration, centrifugation, etc. Troubleshooting Table Heterogeneous viscosity inside the SPE cartridge/s, caused by the use of different liquids in successive SPE steps. Condition Wash and Elute Reduce the residual level of liquid above the frit to 1 to 2 mm before conditioning with another type of liquid. Before using a new solvent, ensure that all effluent has been expelled from the SPE cartridges. Leak in the manifold gasket. All Replace the manifold gasket. Refer to page 31. Liquid continues to flow, even after the SPE control dial has been set to Off. The process control dial is set to Dry. Residual positive pressure remains in the SPE cartridge/s. All Switch the process control dial to SPE. Switch the SPE control dial to Low Flow before stopping. Unseat the manifold. Refer to page USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD ASPEC Positive Pressure Manifold User's Guide 33

33 Symptoms Possible Causes SPE Steps Solutions Previous samples overflowed. Load Replace the manifold gasket. Refer to page 31. Troubleshooting Table Contamination Lower recoveries than usual for an optimized SPE protocol. Unclean collection tubes. Elution solvent splashed. SPE cartridge packing material dried. Not enough time for extraction to be completed. Residual trace of the washing solvent inside the packing material of the SPE cartridge/s prior to the elution step. Elution Condition Load Elution Wash Replace the collection vessels. Reduce the elution flow rate. When the liquid level on the fastest eluting SPE cartridge reaches 2 mm above the top frit (High Flow), switch to the SPE control dial to Low Flow, and then slowly turn the low flow adjustment knob clockwise until flow restarts and the liquid level equilibrates for all cartridges. Decrease the flow rate to better extract analytes from the sample matrices. Decrease the flow rate to better extract analytes from the solid phase. Switch the process control dial to Dry after the last washing step for several minutes. Troubleshooting Table Fewer interferents removed than usual for an optimized SPE protocol. Residual trace of the washing solvent inside the packing material of the SPE cartridge/s prior to the elution step. Not enough time to remove interferents. Wash Turn the process control dial to Dry after the last wash step. Thoroughly dry the SPE cartridges for several minutes. Decrease flow rate. A new batch of SPE cartridges. Elution Replace the SPE cartridges with a new batch. 34 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD ASPEC Positive Pressure Manifold User's Guide 35

34 Repair and Return Policies Repair and Return Policies Refer to the following information and then contact your local Gilson representative. Specific contact information can be found at Before Calling Us Your local Gilson representative will be able to serve you more efficiently if you have the following information: Serial number and model number of the instrument, located on the rear of the base. List of concise symptoms List of operating procedures and conditions you were using when the problem arose Warranty Repair Units covered under warranty will be repaired and returned to you at no charge. If you have any questions about applicability, contact your local Gilson representative. Non-Warranty Repair For out-of-warranty repairs, contact your local Gilson representative who will discuss service options with you and can assist in making arrangements to return the equipment, if necessary. 36 USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

35 Return Procedure Contact your local Gilson representative to obtain authorization before returning any Gilson equipment. To return a piece of equipment: Carefully pack the unit to prevent damage in transit. Check with your local Gilson representative regarding proper method of shipment. No responsibility is assumed by Gilson or your local Gilson representative for damage caused by improperly packaged instruments. Indicate the authorization on the carton and on the packing slip. Always insure for the replacement value of the unit. Include a description of symptoms, your name, address, phone number, and purchase order to cover repair costs, return and shipping charges, if your institution requires it. Unit End-of-Life When a unit reaches the end of its useful life, refer to for directions and information on the end-of-life policy. This is in accordance with the European Union Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). Repair and Return Policies ASPEC Positive Pressure Manifold User's Guide 37

36 Replacement Parts and Accessories Replacement Parts and Accessories Description Part Number 1 ml plugs for 24-position racks (qty. 24) ml plugs for 24-position racks (qty. 24) ml plugs for 15-position racks (qty. 15) well collection plate, 1 ml (qty. 10) well collection plate, 2 ml (qty. 10) well plate adapter (qty. 1) Collection and drain well (qty. 1) Ejection plate for SPE cartridges (qty. 1) External gas regulator, 15 psi (qty. 1) Gasket, manifold, 96-positions (qty. 10) Gasket, manifold, 24-positions (qty. 10) Gasket, manifold, 15-positions (qty. 10) Manifold, 96-positions (qty. 1) Manifold, 24-positions (qty. 1) Manifold, 15-positions (qty. 1) O-rings, manifold seals (qty. 5) SPE cartridge rack, 1 ml (qty. 1) SPE cartridge rack, 3 ml (qty. 1) SPE cartridge rack, 6 ml (qty. 1) Safety shield (qty. 1) Tubes, 12 x 75 mm, 5 ml, glass (qty. 250) Tubes, 15 x 85 mm, 10 ml, glass (qty. 250) USER S GUIDE ASPEC POSITIVE PRESSURE MANIFOLD

37 Configuration Kits Description Part Number 96-position position, 1 ml position, 3 ml position, 6 ml ASPEC Positive Pressure Unit Description Part Number ASPEC positive pressure unit Configuration Kits ASPEC Positive Pressure Manifold User's Guide 39

38 LT

200i User s information manual

200i User s information manual M2i-UM-1 WARNING: If the information in this manual is not followed exactly, a fire or explosion may result, causing property damage, personal injury or loss of life. Cast iron condensing boiler 200i User

More information

Installation Instructions

Installation Instructions Design Guide with Installation Instructions Wine Reserve ZDWT240 and Beverage Center ZDBT240 monogram.com Safety Information BEFORE YOU BEGIN: Read these instructions completely and carefully. IMPORTANT

More information

SOLA SM II Light Engine Instruction Manual

SOLA SM II Light Engine Instruction Manual SOLA SM II Light Engine Instruction Manual Lumencor, Inc. Document Number 52-10036 www.lumencor.com Emissions Certifications This equipment has been tested and found to comply with the limits of EMC directive

More information

Installation Instructions If you have questions, call or visit our website at:

Installation Instructions If you have questions, call or visit our website at: Installation Instructions If you have questions, call 800.626.2000 or visit our website at: www.monogram.com Wine Reserve ZDWT240 and Beverage Center ZDBT240 Design Guide With Installation Instructions

More information

Vulcan Fire Module WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM

Vulcan Fire Module WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM www.inspiredfirefx.com Vulcan Fire Module (VFM) Owner s Manual Installation and Operation Vulcan Fire Module Certified by Lab Test Certification Meets: ANSI Z21.97-2014 CSA 2.41-2014 CSA C22.2 No. 3-M1998

More information

Stopper Station Series SS-2008 Push Button Pneumatic Timer Button

Stopper Station Series SS-2008 Push Button Pneumatic Timer Button Stopper Station Series SS-2008 Push Button Pneumatic Timer Button ADA for operation Pneumatic Timer Models SS-2008 Red SS-2108 Green SS-2208 Yellow SS-2308 White SS-2408 Blue ALL MODELS COME WITH A COLOR

More information

An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WARNING

An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WARNING www.inspiredfirefx.com Commercial Grade All Weather Electronic Ignition System (Lateral Offset) Owner s Manual Installation and Operation Certified by Lab Test Certification Meets: ANSI Z21.97-2014 CSA

More information

HEARTH PRODUCTS KITS AND ACCESSORIES. KIT CONTENTS (See Figure 1) TOOLS NEEDED

HEARTH PRODUCTS KITS AND ACCESSORIES. KIT CONTENTS (See Figure 1) TOOLS NEEDED HEARTH PRODUCTS KITS AND ACCESSORIES P/N 900191-00 Rev. NC, 01/2014 Gas Conversion KIT, NG to lp INSTALLATION INSTRUCTIONS FOR CONVERTING FROM NATURAL GAS (NG) TO PROPANE gas (LP). for use with Madison

More information

Installation Instructions

Installation Instructions Installation Instructions 42" Island Vent Hood ZV1050 monogram.com 1 Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully. Save these instructions for local inspector s

More information

Stopper Station Series Push Button Models SS2xx2, SS2xx5, SS2xx9

Stopper Station Series Push Button Models SS2xx2, SS2xx5, SS2xx9 Installation and Service Instructions Stopper Station Series Push Button Models SS2xx2, SS2xx5, SS2xx9 ADA Compliant NOTE For LTUL Models, Form C contacts on timer, Rated 30 VDC 3A, the enclosed timer

More information

GARAGE DOOR OPENER KIT

GARAGE DOOR OPENER KIT GARAGE DOOR OPENER KIT P/N 2883417 APPLICATION All 2018 and newer Slingshot models with Garage Door Opener By Homelink Kit PN 2881814 BEFORE YOU BEGIN Read these instructions and check to be sure all parts

More information

AB Parts. ControlNet Coax Tap. Installation Instructions. (Cat. Nos TPR, -TPS, -TPYR, -TPYS) What s in This Document

AB Parts. ControlNet Coax Tap. Installation Instructions. (Cat. Nos TPR, -TPS, -TPYR, -TPYS) What s in This Document Installation Instructions ControlNet Coax Tap (Cat. Nos. 1786-TPR, -TPS, -TPYR, -TPYS) What s in This Document Use this document as a guide when installing a ControlNet coax tap. To: See Page: verify package

More information

Lumination TM Volumetric Retrofit Kit

Lumination TM Volumetric Retrofit Kit GE Lighting Installation Guide Lumination TM Volumetric Retrofit Kit BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING AVERTISSEMENT RISK OF FIRE OR ELECTRIC SHOCK Luminaire wiring

More information

WARNING WARNING WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM

WARNING WARNING WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM theoutdoorplus.com Owner s Manual Electronic Ignition Commercial Grade System Installation and Operation Improper installation, adjustment, alteration, service or maintenance can cause injury or property

More information

INSTALLATION INSTRUCTION In-Ground

INSTALLATION INSTRUCTION In-Ground SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified electrician in accordance

More information

WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM

WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM Outdoorfiredesigns.com Automated Tiki Torch (AWEIS) Owner s Manual Installation and Operation Certified by Lab Test Certification Meets: ANSI Z21.97-2014 CSA 2.41-2014 CSA C22.2 No. 3-M1998 (R2014) Improper

More information

INSTALLATION INSTRUCTION In-Ground Color Changing

INSTALLATION INSTRUCTION In-Ground Color Changing SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified electrician in accordance

More information

Installation Instructions If you have questions, call or visit our website at:

Installation Instructions If you have questions, call or visit our website at: Installation Instructions If you have questions, call 800.626.2000 or visit our website at: www.monogram.com Outdoor/Indoor Refrigerator ZDOD240 Design Guide With Installation Instructions Safety Information

More information

WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM

WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM www.firebydesign.com Wharf DC Branch Twist Fire Feature Owner s Manual Installation and Operation Certified by Underwriters Laboratories Meets: ANSI Z21.97-2014 CSA 2.41-2014 CSA C22.2 No. 3-M1998 (R2014)

More information

ChemScan mini Analyzer for Low Ammonia Monitoring Installation, Operation and Maintenance Manual

ChemScan mini Analyzer for Low Ammonia Monitoring Installation, Operation and Maintenance Manual ChemScan mini Analyzer for Low Ammonia Monitoring Installation, Operation and Maintenance Manual asaanalytics.com ChemScan mini Low Ammonia Analyzer O&M Manual - Rev 223K TABLE OF CONTENTS ANALYZER DESCRIPTION

More information

Installation Instructions

Installation Instructions Design Guide with Installation Instructions Double-Drawer Built-In Refrigerator ZIDI240 ZIDS240 monogram.com Safety Information BEFORE YOU BEGIN: Read these instructions completely and carefully. IMPORTANT

More information

Installation Instructions

Installation Instructions Installation Instructions (Cat. No. 1794-OB16) 3 7 1 English 2 6 4 5 Module Installation This module mounts on a 1794 terminal base unit. 1. Rotate keyswitch (1) on terminal base unit (2) clockwise to

More information

UNI 321. User s Guide

UNI 321. User s Guide UNI 321 User s Guide Ver 1.1 Dec. 2018 Contents Read Before Operating... 2 General Information... 3 User Interface... 3 Display... 3 Normal Operation... 3 Normal Mode Operation... 4 Turning the Unit On...

More information

Aquatron 4, 8, /95 Form Number Instructions For Use. Advance Models , , , ,

Aquatron 4, 8, /95 Form Number Instructions For Use. Advance Models , , , , Aquatron 4, 8, 11 Instructions For Use Advance Models 56250191, 56250192, 56250193, 56250205, 56250207 10/95 Form Number 56041318 TABLE OF CONTENTS Page Introduction...2 Parts and Service...2 Nameplate...2

More information

Operation & Care Instructions Save For Future Reference ABOUT THE MACHINE

Operation & Care Instructions Save For Future Reference ABOUT THE MACHINE Operation & Care Instructions Save For Future Reference Model Euro 930 Hepa vac Dry Canister HEPA Vacuum Cleaner This product is a high performance dry canister vacuum for commercial/industrial use. All

More information

Instruction Manual Round Top Hotplate-Stirrers. Advanced Unit

Instruction Manual Round Top Hotplate-Stirrers. Advanced Unit Instruction Manual Round Top Hotplate-Stirrers Advanced Unit TABLE OF CONTENTS Package Contents............... 1 Warranty............... 1 Installation............... 2 Maintenance & Servicing...............

More information

Instruction Manual CG-1999-V-10 CG-1999-V-10E Heating Magnetic Stirrer

Instruction Manual CG-1999-V-10 CG-1999-V-10E Heating Magnetic Stirrer www.cglifesciences.com Phone: 1-800-843-1794 by VELP Scientifica Instruction Manual CG-1999-V-10 CG-1999-V-10E Heating Magnetic Stirrer General Information Before using the unit, please read the following

More information

Instruction Manual Advanced Mini Block Heaters Advanced Mini Block Heater with Heated Lid

Instruction Manual Advanced Mini Block Heaters Advanced Mini Block Heater with Heated Lid Instruction Manual Advanced Mini Block Heaters Advanced Mini Block Heater with Heated Lid Table of Contents Package Contents.............. 1 Warranty.............. 1 Installation.............. 2 Maintenance

More information

520 Series. TankMixer water heater tank mixing valve NA Function

520 Series.   TankMixer water heater tank mixing valve NA Function NA10482.01 www.caleffi.com TankMixer water heater tank mixing valve Copyright 2018 Caleffi 520 Series Function The Caleffi TankMixer 520_AX series kit combines a three-way thermostatic mixing valve with

More information

520 Series. AngleMix Thermostatic mixing valve NA Function

520 Series.   AngleMix Thermostatic mixing valve NA Function NA10618 www.caleffi.com AngleMix Thermostatic mixing valve Copyright 2018 Caleffi Function 520 Series The Caleffi AngleMix 520 series thermostatic mixing valve is used in systems producing domestic hot

More information

Narrow Depth Reach-in Refrigerator And Freezer Refrigerator model: 178A19RHC, 178A23RHC, 178A49RHC Freezer model: 178A19FHC, 178A23FHC, 178A49FHC

Narrow Depth Reach-in Refrigerator And Freezer Refrigerator model: 178A19RHC, 178A23RHC, 178A49RHC Freezer model: 178A19FHC, 178A23FHC, 178A49FHC Commercial Refrigerator And Freezer User s Manual Narrow Depth Reach-in Refrigerator And Freezer Refrigerator model: 178A19RHC, 178A23RHC, 178A49RHC Freezer model: 178A19FHC, 178A23FHC, 178A49FHC 10/2016

More information

WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM

WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM www.firebydesign.com All Weather Electronic Ignition Commercial Grade System Owner s Manual Installation and Operation (LINEAR FEATURES) Improper installation, adjustment, alteration, service or maintenance

More information

SEL-3422 Motor Relay HMI Quick-Start Guide

SEL-3422 Motor Relay HMI Quick-Start Guide SEL-3422 Motor Relay HMI Quick-Start Guide Overview The SEL-3422 Motor Relay HMI indicates the SEL-849 operation status through the ten LEDs on its front panel. Eight of these LEDs are programmable. The

More information

WARNING Do not store or use gasoline or other flammable vapors and liquids in vicinity of this or any other appliance. WARNING

WARNING Do not store or use gasoline or other flammable vapors and liquids in vicinity of this or any other appliance. WARNING www.theoutdoorplus.com (909) 460-5579 All Weather Electronic Ignition System (12 Volt AC) Owner s Manual Installation and Operation Certified by Lab Test Certification Meets: ANSI Z21.97-2014 CSA 2.41-2014

More information

Installation Instructions If you have questions, call or visit our website at:

Installation Instructions If you have questions, call or visit our website at: Installation Instructions If you have questions, call 800.626.2000 or visit our website at: www.monogram.com Wine Chiller ZDWC240NBS and Beverage Center ZDBC240NBS Design Guide With Installation Instructions

More information

WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM

WARNING. For Use with NATURAL or LP GAS Only NO SOLID FUELS TO BE USED WITH THIS SYSTEM www.firebydesign.com All Weather Electronic Ignition Commercial Grade System Owner s Manual Installation and Operation (ROUND/SQUARE FEATURES) Improper installation, adjustment, alteration, service or

More information

User Manual. Ice Cream Dipping Cabinet User s Manual 360ADC4HC, 360ADC4CHC, 360ADC4FHC

User Manual. Ice Cream Dipping Cabinet User s Manual 360ADC4HC, 360ADC4CHC, 360ADC4FHC Ice Cream Dipping Cabinet User s Manual 360ADC4HC, 360ADC4CHC, 360ADC4FHC 360ADC8HC, 360ADC8CHC, 360ADC8FHC 03/2018 Please read the manual thoroughly prior to equipment set-up, operation and maintenance.

More information

PUREFIRE GAS BOILERS USER S INFORMATION MANUAL PB HEAT, LLC 131 S. CHURCH ST BALLY, PA WARNING MISE EN GARDE TO BE COMPLETED BY THE INSTALLER

PUREFIRE GAS BOILERS USER S INFORMATION MANUAL PB HEAT, LLC 131 S. CHURCH ST BALLY, PA WARNING MISE EN GARDE TO BE COMPLETED BY THE INSTALLER USER S INFORMATION MANUAL PUREFIRE GAS BOILERS TO THE INSTALLER:This manual is the property of the owner and must be affixed near the boiler for future reference. TO THE OWNER: This boiler should be inspected

More information

1495D. Installation and Operation Manual, 230 Voltage 2/16/2017

1495D. Installation and Operation Manual, 230 Voltage 2/16/2017 1495D Installation and Operation Manual, 230 Voltage 2/16/2017 VWR Vacuum Oven 230 Voltage (1495D) Installation and Operation Manual Part Number (Manual): 4861421 Revision: February 16, 2017 Ü CAN/CSA-C22.2

More information

SOLA SM and SOLA SM 365 Light Engine Instruction Manual

SOLA SM and SOLA SM 365 Light Engine Instruction Manual SOLA SM and SOLA SM 365 Light Engine Instruction Manual Lumencor, Inc. Document Number 57-10003 www.lumencor.com Regulatory Models Lumencor utilizes regulatory model names for all certified and CE marked

More information

USER S INFORMATION MANUAL PB HEAT, LLC 131 S. CHURCH ST BALLY, PA WARNING MISE EN GARDE TO BE COMPLETED BY THE INSTALLER.

USER S INFORMATION MANUAL PB HEAT, LLC 131 S. CHURCH ST BALLY, PA WARNING MISE EN GARDE TO BE COMPLETED BY THE INSTALLER. USER S INFORMATION MANUAL SERIES PBC COMBINATION GAS BOILERS TO THE INSTALLER:This manual is the property of the owner and must be affixed near the boiler for future reference. TO THE OWNER: This boiler

More information

Alpine CONDENSING HIGH EFFICIENCY GAS-FIRED HOT WATER BOILER

Alpine CONDENSING HIGH EFFICIENCY GAS-FIRED HOT WATER BOILER USER'S INFORMATION MANUAL Alpine CONDENSING HIGH EFFICIENCY GAS-FIRED HOT WATER BOILER If the information in this manual is not followed exactly, a fire or explosion may result causing property damage,

More information

PEDESTAL INSTALLATION INSTRUCTIONS INSTRUCTIONS D INSTALLATION DU PIÉDESTAL

PEDESTAL INSTALLATION INSTRUCTIONS INSTRUCTIONS D INSTALLATION DU PIÉDESTAL PEDESTAL INSTALLATION INSTRUCTIONS INSTRUCTIONS D INSTALLATION DU PIÉDESTAL Table of Contents PEDESTAL SAFETY... 1 INSTALLATION REQUIREMENTS... 2 Tools and Parts... 2 Location Requirements... 2 Before

More information

SERIES PSCII GAS BOILERS

SERIES PSCII GAS BOILERS USER S INFORMATION MANUAL SERIES PSCII GAS BOILERS TO THE INSTALLER:This manual is the property of the owner and must be affixed near the boiler for future reference. TO THE OWNER: This boiler should be

More information

Instruction Manual. Hotplate-Stirrers

Instruction Manual. Hotplate-Stirrers Instruction Manual Advanced Round Top Hotplate-Stirrers Table of Contents Package Contents............ 1 Warranty............ 1 Installation............ 2 Maintenance & Servicing............ 2 Intended

More information

GBX GAS BOILERS USER S INFORMATION MANUAL

GBX GAS BOILERS USER S INFORMATION MANUAL S-GBXUM-2 00-GBXUM GBX GAS BOILERS USER S INFORMATION MANUAL WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury

More information

IMPORTANT: Read carefully before installation and retain for future reference. NOTE: Installation must be conducted by licensed electrician.

IMPORTANT: Read carefully before installation and retain for future reference. NOTE: Installation must be conducted by licensed electrician. INSTALLATION AND MAINTENANCE MANUAL StarPower Link LED Luminaire (Damp Location) Document No: 0077 Rev B Apr. 2015 IMPORTANT: Read carefully before installation and retain for future reference. NOTE: Installation

More information

Service Procedures for the Model SL31-31 Dryer

Service Procedures for the Model SL31-31 Dryer Service Procedures for the Model SL31-31 Dryer Hot Surface Ignitor Gas American Dryer Corporation 88 Currant Road Fall River MA 02720-4781 USA Telephone: (508) 678-9000 / Fax: (508) 678-9447 e-mail: techsupport@amdry.com

More information

Code 542 Peltier Rack User's Guide

Code 542 Peltier Rack User's Guide Code 542 Peltier Rack User's Guide LT2544/ 1999 Gilson, Inc. All rights reserved June 1999 Table of Contents page Introduction...1-1 Unpacking...1-2 Customer Service...1-3 Technical Specifications...1-4

More information

Spectra FIA Light Engine Instruction Manual

Spectra FIA Light Engine Instruction Manual Spectra FIA Light Engine Instruction Manual Lumencor, Inc. Document Number 57-10008 www.lumencor.com Emissions Certifications This equipment has been tested and found to comply with the limits of EMC directive

More information

Siemens Automation Products Siemens AG All rights reserved A5E AB, 08/2017 1

Siemens Automation Products Siemens AG All rights reserved A5E AB, 08/2017 1 SIMATIC IPC277E Product Information General notes ATEX/IECEx - Additional Instructions for use in Gas Explosive Atmospheres (only valid for specific MLFBs - marked with IECEx/ATEX symbol on the nameplate

More information

Tetra MAX. LED Lighting System. BEFORE YOU BEGIN Read these instructions completely and carefully. Installation Guide

Tetra MAX. LED Lighting System. BEFORE YOU BEGIN Read these instructions completely and carefully. Installation Guide Tetra MAX LED Lighting System Installation Guide Volt GEMXRD-W, GEMXHRD-W, GEMXGL-W, GEMXBL-W, GEMXYG-W BEFORE YOU BEGIN Read these instructions completely and carefully. RISK OF ELECTRIC SHOCK Turn power

More information

An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WARNING

An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WARNING www.firebydesign.com All Weather Electronic Ignition System (AWEIS) Owner s Manual Installation and Operation Certified by Lab Test Certification Meets: ANSI Z21.97-2014 CSA 2.41-2014 CSA C22.2 No. 3-M1998

More information

USER'S INFORMATION MANUAL SERIES 2 GAS - FIRED

USER'S INFORMATION MANUAL SERIES 2 GAS - FIRED USER'S INFORMATION MANUAL SERIES 2 GAS - FIRED BOILER WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss

More information

APEX CONDENSING HIGH EFFICIENCY GAS-FIRED HOT WATER BOILER

APEX CONDENSING HIGH EFFICIENCY GAS-FIRED HOT WATER BOILER USER'S INFORMATION MANUAL APEX CONDENSING HIGH EFFICIENCY GAS-FIRED HOT WATER BOILER If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal

More information

Lumination TM Controls Accessory LPL Series Controller Box

Lumination TM Controls Accessory LPL Series Controller Box Installation Guide Lumination TM Controls Accessory LPL Series Controller Box BEFORE YOU BEGIN Read these instructions completely and carefully. RISK OF FIRE OR ELECTRIC SHOCK Turn power off before inspection,

More information

Instruction Manual Standard Dry Block Heaters Advanced Dry Block Heaters U L

Instruction Manual Standard Dry Block Heaters Advanced Dry Block Heaters U L Instruction Manual Standard Dry Block Heaters Advanced Dry Block Heaters 1 U L Table of Contents Package Contents.............. 1 Warranty.............. 1 Installation.............. 2 Maintenance & Servicing..............

More information

INTRODUCTION. Industry Canada: Canadian ID: 6982A-YRHCPZW0 (Z-Wave); 6982A-YRHCPZB0 (Zigbee)

INTRODUCTION. Industry Canada: Canadian ID: 6982A-YRHCPZW0 (Z-Wave); 6982A-YRHCPZB0 (Zigbee) Industry Canada: Canadian ID: 6982A-YRHCPZW0 (Z-Wave); 6982A-YRHCPZB0 (Zigbee) This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation

More information

Air Conditioner

Air Conditioner RECORD THIS UNIT INFORMATION FOR FUTURE REFERENCE: Model Number Serial Number Date Purchased USA SERVICE OFFICE Dometic, LLC 2320 Industrial Parkway Elkhart, IN 46516 574-294-2511 Roof Top Unit Description

More information

Intelligent Home Solutions Quick Start Guide. Monitor your home from anywhere with your smartphone

Intelligent Home Solutions Quick Start Guide. Monitor your home from anywhere with your smartphone Model: isb01 Intelligent Home Solutions Quick Start Guide Wi-Fi MOTION SENSOR Monitor your home from anywhere with your smartphone WHAT YOU LL NEED WiFi network transmitting at 2.4GHz; WPA2 security type

More information

Tank, Heater, and Control Operation Manual REV. E DATE: 04May2015

Tank, Heater, and Control Operation Manual REV. E DATE: 04May2015 Tank, Heater, and Control Operation Manual 25-710-804 REV. E DATE: 04May2015 Hanson Research Corporation 9810 Variel Avenue Chatsworth, CA 91311 USA (800) 821-8165 (818) 882-7266 FAX (818) 882-9470 www.hansonresearch.com

More information

Installation Instruction Danfoss RX-C Roof and Gutter De-Icing System

Installation Instruction Danfoss RX-C Roof and Gutter De-Icing System Danfoss RX-C Roof and Gutter De-Icing System Table of contents 1 Overview 3 2 Safety 3 3 Certifications / Approvals 4 4 Technical data 4 5 Personnel requirements 4 6 System design 5 7 Power connection

More information

Performance Thermal Binder

Performance Thermal Binder Performance Thermal Binder TM Helios 60 E F S Please read these instructions before use. Lire ces instructions avant utilisation. Lea estas instrucciones antes de usar la máquina. INDEX LAMINATOR CONTROLS

More information

QUICK START GUIDE. Lono, LLC 686 East 110 South, Suite 102 American Fork, UT 84003

QUICK START GUIDE. Lono, LLC 686 East 110 South, Suite 102 American Fork, UT 84003 QUICK START GUIDE Lono, LLC 686 East 110 South, Suite 102 American Fork, UT 84003 Welcome. This guide will help you install your Lono controller. For additional information, check out our installation

More information

Reacti-Therm I and III Heating Modules

Reacti-Therm I and III Heating Modules INSTRUCTIONS Reacti-Therm I and III Heating Modules TS-18822 TS-18824 Number TS-18822 TS-18824 Description Reacti-Therm I Heating Module (single block) Reacti-Therm III Heating Module (triple block) 2101.1

More information

Supplemental Installation & Operation Manual. THE COLDWELL Stainless Steel Cold Trap

Supplemental Installation & Operation Manual. THE COLDWELL Stainless Steel Cold Trap Supplemental Installation & Operation Manual THE COLDWELL Stainless Steel Cold Trap For use with Labconco CentriVap cold traps KF25 Connections INTRODUCTION Locations and Applications Range This cold trap

More information

AGA TOTAL CONTROL. Model No. - TC3

AGA TOTAL CONTROL. Model No. - TC3 AGA TOTAL CONTROL Model No. - TC3 Installation Guide REMEMBER: when replacing a part on this appliance, use only replacement parts that you can be assured conform to the safety and performance specification

More information

OWNER S MANUAL INSTALLATION OPERATION MAINTENANCE CONVECTION OVEN MODEL # RDCO-32

OWNER S MANUAL INSTALLATION OPERATION MAINTENANCE CONVECTION OVEN MODEL # RDCO-32 OWNER S MANUAL INSTALLATION OPERATION MAINTENANCE CONVECTION OVEN MODEL # RDCO-32 All Rankin-Delux, Inc. equipment is manufactured for use with the type of gas specified on the rating plate and for installation

More information

Instruction manual

Instruction manual 9410 9450 Safety Printer and interface overview Starting / shutting down the printer Sending a job for printing Modifying a job Consulting the history Replacing the consumables Head cleaning Troubleshooting

More information

Wi-Fi DOOR/WINDOW SENSOR

Wi-Fi DOOR/WINDOW SENSOR Model: isb04 Intelligent Home Solutions Quick Start Guide Wi-Fi DOOR/WINDOW SENSOR Monitor your home from anywhere with your smartphone WHAT YOU LL NEED WiFi network transmitting at 2.4GHz; WPA2 security

More information

USER'S INFORMATION MANUAL SERIES 2 GAS - FIRED

USER'S INFORMATION MANUAL SERIES 2 GAS - FIRED USER'S INFORMATION MANUAL SERIES 2 GAS - FIRED BOILER : If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

More information

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE ZR Series Commercial Specification Troffers with Emergency Driver Includes: ZR14, ZR22 and ZR24 IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed

More information

Smoke Control Listed LCM-OAVS VAV with HW Reheat, Two Venturi Air Valves (One Exhaust, One Supply) including BTU Compensation

Smoke Control Listed LCM-OAVS VAV with HW Reheat, Two Venturi Air Valves (One Exhaust, One Supply) including BTU Compensation Smoke Control Listed LCM-OAVS VAV with HW Reheat, Two Venturi Air Valves (One Exhaust, One Supply) including BTU Compensation Generic Controller I/O Layout. See Wiring Diagram for application specific

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual Document 474741 Model XCR and XIR Ceiling Exhaust and Inline Fans Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS with Design Guide Double-Drawer Built-In Refrigerator Monogram.com Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT Save these instructions

More information

Instruction Manual. Undercounter Refrigerator Models HR24B. hoshizakiamerica.com

Instruction Manual. Undercounter Refrigerator Models HR24B. hoshizakiamerica.com Instruction Manual Undercounter Refrigerator Models HR24B hoshizakiamerica.com Issued: 5-11-2018 WARNING Only qualified service technicians should install and service the appliance. To obtain the name

More information

User s Manual for FT SERIES THE

User s Manual for FT SERIES THE User s Manual Document 1343D User s Manual for THE FT SERIES Wall-Mounted, Modulating Gas, Condensing, Heating Only, Boiler Model FTHW 80,000 BTU/hr 100,000 BTU/hr 120,000 BTU/hr 140,000 BTU/hr 199,000

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual Document 474680 Model SP and CSP Ceiling Exhaust and Inline Fans Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting

More information

Illuminated Stopper Station Push Button

Illuminated Stopper Station Push Button Illuminated Stopper Station Push Button Model SS2xx6 Rely on STI Dimensions 4.880 in [123.95 mm] 3.218 in [81.74 mm] 1.625 in [41.28 mm].875 in [22.23 mm] Switch Rating 2 momentary independent Form C contacts,

More information

WATER BATHS. MODELS: SWBC22 and SWBC22-2 MICROPROCESSOR CONTROLLED INSTALLATION AND OPERATION MANUAL 12/

WATER BATHS. MODELS: SWBC22 and SWBC22-2 MICROPROCESSOR CONTROLLED INSTALLATION AND OPERATION MANUAL 12/ WATER BATHS MODELS: SWBC22 and SWBC22-2 Previously designated as WPC65 & WPC65-2 MICROPROCESSOR CONTROLLED INSTALLATION AND OPERATION MANUAL 12/2013 4861565 These units are TUV CUE listed as water baths

More information

DELTA HEAT SIDE BURNER

DELTA HEAT SIDE BURNER DELTA HEAT SIDE BURNER USE & CARE MANUAL MODEL: DHSB1D-C DHSB2-C P/N: 18778J 01/19 IMPORTANT SAFETY INFORMATION WARNING! Read this manual carefully and completely before using your grill to ensure proper

More information

OPERATOR. Shadow 17, 20 Models , , , M A N U A L A N D P A R T S L I S T

OPERATOR. Shadow 17, 20 Models , , , M A N U A L A N D P A R T S L I S T OPERATOR M A N U A L A N D P A R T S L I S T Shadow 17, 20 Models 56201101, 56201102, 56201355 56201250, 56201586 3/96 reivsed 10/03 Form Number 56041342 TECHNICAL SPECIFICATIONS Model Shadow 17 Shadow

More information

FES - Series Portable Electric Heaters

FES - Series Portable Electric Heaters FOSTORIA INDUSTRIES 114 Roscoe Fitz Road Gray, TN 37615 Phone: 800-495-4525 Fax: 419-435-0842 www.fostoriaindustries.com Division of TPI Corporation YES - Series Suspended Electric Heaters FES - Series

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual Document 474680 Model SP Model CSP Ceiling Exhaust and Inline Fans Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting

More information

Installation Instructions If you have questions, call or visit our website at:

Installation Instructions If you have questions, call or visit our website at: Installation Instructions If you have questions, call 800.626.2000 or visit our website at: www.monogram.com Fresh-Food Refrigerator ZIFI240 ZIFS240 Bar Refrigerator with Icemaker ZIBI240 ZIBS240 Design

More information

Wireless Outdoor Air Reset Adaptor PN:

Wireless Outdoor Air Reset Adaptor PN: Wireless Outdoor Air Reset Adaptor PN: 105767-01 Instruction Sheet APPLICATION The Wireless Outdoor Air Reset Adaptor, when connected to the Concert Boiler Control enables efficiency control functionality

More information

Draft - develop and review

Draft - develop and review MST Personnel Proximity Detection System Overview v. #.# Draft - develop and review System Overview 2.0 - Proximity Detection System.docx 1 January 2014 Page 1 of 18 The MST Proximity Solution The MST

More information

Installation Instructions If you have questions, call 800-GE-CARES or visit our website at:

Installation Instructions If you have questions, call 800-GE-CARES or visit our website at: Installation Instructions If you have questions, call 800-GE-CARES or visit our website at: www.monogram.com 30" Convection Built-In Ovens Models: ZET1038 ZET1058 Monogram. We bring good things to life.

More information

Refrigerant Recovery Machine. Model No Operating Manual

Refrigerant Recovery Machine. Model No Operating Manual Refrigerant Recovery Machine Model No. 25700 Operating Manual Safety Precautions WARNING : TO PREVENT PERSONAL INJURY AND / OR EQUIPMENT DAMAGE, CAUTION - Risk of injury. This equipment should only be

More information

QAA 142 Termination instructions Self-regulating trace heaters type ELSR-NA and -HA in Div1 with heater entry kit EL-HAZELECT Kit part No: 09CA051

QAA 142 Termination instructions Self-regulating trace heaters type ELSR-NA and -HA in Div1 with heater entry kit EL-HAZELECT Kit part No: 09CA051 QAA 142 Termination instructions Self-regulating trace heaters type ELSR-NA and -HA in Div1 with heater entry kit EL-HAZELECT Kit part No: 09CA051 QAA 142 Instruction de terminaison pour des câbles chauffants

More information

Occupancy Sensor OCS 100W Setup Guide

Occupancy Sensor OCS 100W Setup Guide Sensor OCS 100W Setup Guide The OCS 100W is a wall-mounted occupancy sensor that incorporates ultrasonic (US) and passive infrared (PIR) into a dualtechnology sensor. The US sensor emits ultrasonic sound

More information

All wiring must conform to the N.E.C./C.E.C. and existing local code requirements.

All wiring must conform to the N.E.C./C.E.C. and existing local code requirements. CP & RCP Series Radiant Ceiling Panel Heaters INSTLLTION INSTRUCTIONS GENERL INFORMTION: Wiring: Check voltage on nameplate of heater to make sure it conforms with supply voltage. 277 volt heaters operated

More information

Instruction Manual. Counter Showcase Models HNC-120BA-L/R-SL HNC-150BA-L/R-SL HNC-180BA-L/R-SL HNC-210BA-L/R-SL. hoshizakiamerica.

Instruction Manual. Counter Showcase Models HNC-120BA-L/R-SL HNC-150BA-L/R-SL HNC-180BA-L/R-SL HNC-210BA-L/R-SL. hoshizakiamerica. Instruction Manual Counter Showcase Models HNC-120BA-L/R-SL HNC-150BA-L/R-SL HNC-180BA-L/R-SL HNC-210BA-L/R-SL hoshizakiamerica.com Issued: 5-1-2017 WARNING Only qualifi ed service technicians should install

More information

Installation Instructions

Installation Instructions Installation Instructions If you have questions, call 800.626.2000 or visit our website at: www.monogram.com Automatic Icemaker ZDI15 ZDIS15 Design Guide with Installation Instructions Installation Instructions

More information

Operating Instruction Manual

Operating Instruction Manual COMMERCIAL COUNTERTOP PIZZA OVEN Operating Instruction Manual EPO-1 Model Voltage Power Amperage Dimensions Width Depth Height EPO-1 120V ~ 60Hz 1500W 12.5A 20.86" 14.76" 9.25" BEFORE OPERATING ANY EQUIPMENT,

More information

WATER BATHS MODELS: WPC95 & WPC95-2 INSTALLATION AND OPERATION MANUAL /12 MICROPROCESSOR CONTROLLED

WATER BATHS MODELS: WPC95 & WPC95-2 INSTALLATION AND OPERATION MANUAL /12 MICROPROCESSOR CONTROLLED WATER BATHS MODELS: WPC95 & WPC95-2 MICROPROCESSOR CONTROLLED INSTALLATION AND OPERATION MANUAL 4861564 08/12 These units are TUV CUE listed as general purpose air incubators for professional, industrial

More information

Operating Instruction Manual

Operating Instruction Manual COMMERCIAL ELECTRIC CONVECTION OVEN Operating Instruction Manual ECO-500 ECO-250 Model Voltage Power Amperage Dimensions Width Depth Height ECO-250 1440W 12A 18.75" 19-7/8" 15" 120V ~ 60Hz ECO-500 1600W

More information

OPERATING INSTRUCTIONS. EchoThermJ ANALOG MULTI-POSITION STIRRERS AND STIRRING HOT PLATES. Document Number HS15-01 Revised May 20, 2011

OPERATING INSTRUCTIONS. EchoThermJ ANALOG MULTI-POSITION STIRRERS AND STIRRING HOT PLATES. Document Number HS15-01 Revised May 20, 2011 OPERATING INSTRUCTIONS EchoThermJ ANALOG MULTI-POSITION STIRRERS AND STIRRING HOT PLATES Document Number HS15-01 Revised May 20, 2011 Torrey Pines Scientific, Inc. 2713 Loker Ave. West Carlsbad, CA 92010

More information

installation manual DM3862 RM2554 DM2663 RM2551 Refrigerator for LP-gas & electric operation DM2852 ! AVERTISSEMENT ! WARNING FOR YOUR SAFETY

installation manual DM3862 RM2554 DM2663 RM2551 Refrigerator for LP-gas & electric operation DM2852 ! AVERTISSEMENT ! WARNING FOR YOUR SAFETY RM25 RM254 RM245 RM2454 RM255 RM2554 DM2652 DM2662 DM266 DM2852 DM2862 DM862 NDM062 NDR292 installation manual Refrigerator for LP-gas & electric operation FOR YOUR SAFETY If you smell gas:. Open windows.

More information

USER'S INFORMATION MANUAL ES2 GAS - FIRED

USER'S INFORMATION MANUAL ES2 GAS - FIRED USER'S INFORMATION MANUAL ES2 GAS - FIRED BOILER WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

More information