Manuel Guide Lighting Fixtures

Transcription

1 Manuel Guide Lighting Fixtures Models: DL-T2424, DL-T3639, DL-T4854 Please read these manuals in their entirety before using these products.

2 Safety Instructions Important Safety Note: To guard against injury, basic precautions should be observed, including the following: A) READ AND FOLLOW ALL SAFETY INSTRUCTIONS. B) DANGER To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment. For each of the following situations, do not attempt repairs by yourself; return the appliance to an authorized service facility for service or discard the appliance: 1) If the appliance falls into the water, DON T reach for it! First unplug it and then retrieve it. If electrical components of the appliance get wet, unplug the appliance immediately. (Non-immersible equipment only) 2) If the appliance shows any sign of abnormal water leakage, immediately unplug it from the power source. (Immersible equipment only) 3) Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet. 4) Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or has been dropped or damaged in any manner. 5) To avoid the possibility of the appliance plug or receptacle getting wet, position aquarium stand and tank to one side of a wall-mounted receptacle to prevent water from dripping onto the receptacle or plug. A drip loop," shown in the figure below, should be arranged by the user for each cord connecting an aquarium appliance to a receptacle. The drip loop" is that part of the cord below the level of the receptacle, or the connector if an extension cord is used, to prevent water traveling along the cord and coming in contact with the receptacle. If the plug or receptacle does get wet, DON T unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then, unplug and examine for presence of water in the receptacle. C) Close supervision is necessary when any appliance is used by or near children. D) To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs, and the like. E) Always unplug an appliance from an outlet when not in use, before putting on or taking off parts, and before cleaning. Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect. F) Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition. G) Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing. H) Make sure an appliance mounted on a tank is securely installed before operating it. I) Read and observe all the important notices on the appliance. J) If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled. K) For added safety, the appliance must be plugged into a receptacle controlled by a GFCI (ground fault interrupter) circuit breaker. Device must be properly connected to a grounded three-prong receptacle. L) This appliance is intended FOR HOUSEHOLD USE ONLY. M) This Light Fixture is required to be used over a covered aquarium. A glass top or protective barrier is required to minimize the fixture's exposure to water. N) SAVE THESE INSTRUCTIONS

3 Fixture Diagram

4 OPERATING LIGHT FIXTURE PRE-OPERATION SETUP 1. Make sure fixture is securely positioned on a covered aquarium. 2. Make sure that all high output T5 bulb pins are fully seated into the T5 end clips. 3. Make sure that all switches are in the off position before plugging in grounded plug(s) in to a power source. START-UP OPERATION 1. Plug grounded plug(s) into a grounded outlet or a power source and turn switch(es) to the on position. a. NOTE It may take up to 5-10 minutes for the T5 bulbs to reach maximum light intensity. 2. Verify that all lamps are lit and functioning properly. 3. Make sure that the cooling fan is on and blowing air into the fixture. a. NOTE fan is powered by the outermost lamps. Be sure to install the lamps used the most in the outer most positions in the light fixture. INSTALLATION & USE 1. Remove Protective Splash Guard Film a. Finnex Aquarium Lightings are shipped with a protective film covering to protect the splash guard from scratches and debris. To remove: i. Place fixture upside down on a smooth clean surface to prevent scratches on the fixture s top finish. ii. Remove screws from the bottom cover (17) from one end of the fixture. iii. Remove the bottom cover from fixture. iv. Remove protective splash guard from fixture. v. On both sides of the splash guard, there is a protective film that must be removed. Film color will vary; transparent, white, blue, etc. vi. Peel away protective film from one end of the splash guard to the other from both sides.

5 2. Remove Reflector Film a. Finnex Aquarium Lightings are shipped with a protective film covering to protect the reflector from scratches and debris. To remove: i. Peel away protective film from one end of reflector to the other ii. Peel slowly to avoid scratches and indentations in the reflector 3. Installing Bulbs (See steps 1-2 below) i. Place fixture upside down on a smooth clean surface to prevent scratches on the fixture s top finish. ii. Remove the screws from the bottom cover from one end of the fixture. iii. Remove the bottom cover from fixture. iv. Remove protective splash guard from fixture. v. Remove protective film from individual reflector vi. Place clip (14) within concave side of reflector (15) and screw down, securing with nut on opposing side. Install clip on other end of reflector. vii. Securely insert T5 bulb into T5 Lamp holder (19) and rotate bulb until locked into place. viii. Clamp reflector on bulb by conjoining secured T5 bulb with the reflectors clip. Rotate reflector to desired angle. Repeat for all T5 bulbs and reflectors. 4. Installing Fixture Legs (See steps 3-4 below) i. Place fixture upside down on a smooth clean surface to prevent scratches on the fixture s top finish. ii. Remove the screws from the bottom cover from one end of the fixture. iii. Remove the bottom cover from fixture. iv. Insert leg stand into leg slot as shown in step 3 v. Lock leg into desired location by tightening leg screw vi. To base leg stand to aquarium, unattach clip at base of leg and reattach at base of leg to form an upside down U shape. This will hold at the inner and outermost lip of aquarium.

6