Industrivej 3-9 DK 9460 Brovst KEF-MOTOR A/S. Fax Instruction Manual PSD 200 Industrial Grinders

Size: px
Start display at page:

Download "Industrivej 3-9 DK 9460 Brovst KEF-MOTOR A/S. Fax Instruction Manual PSD 200 Industrial Grinders"

Transcription

1 KEF-MOTOR A/S Industrivej 3-9 DK 9460 Brovst Tlf Fax Instruction Manual PSD 200 Industrial Grinders

2 EU declaration of conformity KEF-MOTOR A/S Industrivej 3-9 DK-9460 Brovst Denmark Tel.: Fax: hereby declares that KEF Double Ended Grinder PSD 200, are manufactured in accordance with the provisions of the COUNCIL DIRECTIVE of 17. May 2006 (2006/42/EC) The Machinery Directive (order no. 561 of 25 June 1994 with subsequent amendments) 2006/42/EC: 2004/108/EC: 2006/95/EC: Directive on machinery-safety Directive on Electromagnetic Compatibility Low Voltage Equipment Safety directive Also on accordance with: The council directive of 19 February 1973 (73/23/EEC) The Low Voltage Directive with later amendments (order no. 797 of 30 August 1994) The council directive of 3 May 1989 (89/336/EEC) The EMC Directive with later amendments (order no. 796 of 5 December 1991 with subsequent amendments) 2

3 Table of contents 1 TRANSPORT & HANDLING TRANSPORT HANDLING PLACING 4 2 DIRECTIONS FOR USE OPERATION SAFETY RULES FOR STATIONARY POWER TOOLS MAINTENANCE 7 3 BELTARM CHANGING OF GRINDING BELT USE OF BELTARM 8 4 VFCB-COMPLETE EXHAUST UNIT ASSEMBLING AND MOUNTING OF VFCB COMPLETE EXHAUST UNIT MAINTENANCE OF VFCB-EXHAUST UNIT 9 5 SPARE PARTS LIST DRAWING OF PSD 200 BASIC MODEL SPARE PARTS LIST FOR PSD 200 BASIC MODEL SPLIT DRAWING OF PSD 200 COVER SPARE PARTS LIST FOR PSD 200 COVER SPLIT DRAWING OF PSD 200 BELT ARM SPARE PARTS LIST FOR PSD 200 BELTARM SPLIT DRAWING OF VFCB-EXHAUST SYSTEM FOR PSD SPARE PARTS LIST FOR VFCB-EXHAUST UNIT FOR PSD TECHNICAL DATA TECHNICAL SPECIFICATIONS WIRING DIAGRAM DISASWICH W/EMERGENCSTOP GUARANTEE 18 3

4 1 Transport & Handling 1.1 Transport PSD 200 Industrial belt grinder and others are delivered on a pallet packed in protective wrapping. 1.2 Handling The machines can easily be transported on the pallet on which they are delivered. If the machine is delivered on a pedestal you must insure that the pedestal is secured to the pallet. 1.3 Placing Mounting of the machine must take place on a firm level ground. It must be fastened to the ground by means of the four fittings which are used to fasten the machine to the pallet. It is provided with no-volt release protection switch and connected for the wanted voltage. The electrical connection must be performed by an authorized electrician, and it is important to control that the motor (and the exhaust unit) have the correct direction or rotation (please see the arrow on the motor). Before use you must control that the outer cover is solidly mounted on the inner cover. The outer cover must stay mounted during use and should only be dismounted during change of grinding wheel. The grinding wheel must be able to rotate freely without being loose. The tool rest must be adjusted to a distance of approximately 2 mm from the grinding wheel. The eye shield must be clean and adjusted into the right position and the spark arrester must also be adjusted to a distance of approximately 5 mm from the grinding wheel and slightly fastened. The first time you start the belt grinder please let it run at max speed without using it for 5 minutes. Make sure to stay in a safe distance during the machine start-up. 4

5 2 Directions for use 2.1 Operation After adjustment and connection the machine is ready for use. The grinding kan take place by the contact wheel or on the surface grinding table by opening the cover. When you start grinding please start by letting the material touch the grinding wheel lightly and thereby avoid pressuring the grinding wheel to prolonge the lifetime of it. The lifetime of a grinding belt is also prolonged if you start with a light pressure. Please make sure not to overload the motor. Let it run at max speed before start grinding. Grind at max speed and if possible have the material tightened in clamps as it is safer than holding the material in your hands. Avoid grinding on the side of the grinding wheel unless you are using a cup wheel. Do not stop the grinding wheel by pushing any material against it but let it stop by itself. It is very important to keep the working area well lighted. 2.2 Safety rules for stationary power tools. Follow them to achieve best results and full benefit from your new machine The very good craftsman respects the tools with which he works. He knows they represent years of constantly improved design. He also knows that they are dangerous if misused. This is the theme of a new safe-use program for stationary power tools. The safety rules are based on approved practices in industrial and home shops. 2. Keep guard in place and in working order. 3. Ground all tools. If tool is equipped with three-prong plug, it should be plugged into a three-hole electrical receptacle. If an adapter is used to accomodate a two-prong receptacle, the adapter wire must be attached to a known ground. Never remove the third prong. 1. Know your power tool. Read the owner s manual carefully. Learn its applications and limitations, as well as the specific potential hazards peculiar to this tool. 4. Remove adjusting keys and wrenches. Form habit of checking to see that keys and adjusting wrenches is removed before turning it on. 5. Keep work area clean. Cluttered areas and benches invite accidents. 7. Keep children away. All visitors should be kept in a safe distance from work area. 8. Make workshop kidproof with padlocks, master switches, or by removing starter keys. 6. Avoid dangerous environment. Don t use power tools in damp or wet locations or expose them to rain. Keep your work area well lighted. 5

6 9. Don t force tool. It will do the job better and be safer at the rate for which it was designed. 10. Use right tool. Don t force tool or attachment to do a job it was not designed for. 11. Wear proper apparel. Wear no loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair. 12. Always use safety glasses. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses. They are NOT safety glasses. 14. Don t overreach. Keep proper footing and balance at all times. 15. Maintain tools with care. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 13. Secure works. Use clamps or vise to hold works, when pratical. It s safer than using your hands and it frees both hands to operate tool. 16. Disconnect tools before servicing and when changing accessories such as grinding wheels, polishing mops, grinding belts, blades, bits, cutters, etc. 17. Reduce the risk of unintentional starting. Make sure switch is in off position before plugging in. 18. Use recommended accessories. Consult owner s manual for recommended accessories. Use of improper accessories may cause risk of injury to persons. 6

7 2.3 Maintenance Keep the machine in a dry place so the grinding wheels or belts will not risk getting any damp or rain. The grinding wheel will often get uneven because of use and therefore we recommend that you level the grinding wheel off frequently. When the grinding wheel is worn more than 25% we recommend that you change to a new wheel. An uneven grinding wheel causes vibrations which with time will damage the bearings in the machine. Damaged tool rests, eye shields and covers must be replaced to avoid personal damage. When to change the grinding wheel please dismount the outer cover (B). The reverse nut (C) and the outer flange is to be unscrewed, now the outer flange and the grinding wheel can be dismounted. The new grinding wheel is not allowed to exceed the measures shown on the sign on the machine. It is also very important that the hole dimension is correct. The grinding wheels are provided with labels placed around the holes on both sides of the grinding wheel. If these labels are missing or damaged they must be replaced by new ones of the same dimension. The new grinding wheel is to be mounted between the two flanges (D) and the reverse nut (C) screwed on and fastened. The reverse nut (C) is to be fastened so tightly that it can hold the grinding wheel tight but on the other hand it is not to be tightened too much as it can cause unwanted stress in the grinding wheel. Fig.: 2.1 7

8 3 Beltarm 3.1 Changing of grinding belt When the grinding belt is worn out it must be replaced which is done the following way: The top plate on the cover is opened and the handle is pulled down. This way the pressure on the grinding belt will be lowered, so that it can be dismounted and a new grinding belt can be mounted in reverse order. Please control that the arrows on the back of the grinding belt run in the same direction as they point. When the new grinding belt is mounted it is necessary to adjust by the handle for parallel running. The belt is loosened so that the telescopearm and top wheel can be turned with until the grinding belt runs straightly on the contactwheel. After this the handle is fastened. It is only allowed to do this adjustment by pulling the grinding belt with the hands and NOT with power on the machine. 3.2 Use of beltarm Grinding at the beltarm can be done either at the contact wheel or on the grinding surface. You can also dismount the grinding surface for direct unsupported grinding on the grinding belt. Let the material touch the grinding belt softly and avoid uneven grinding as it can damage the grinding belt and overload the motor. 8

9 4 VFCB-complete exhaust unit 4.1 Assembling and mounting of VFCB complete exhaust unit The following description of assembling and mounting of VFCB-exhaust unit is valid both if it is a VFCB-220 or if it is a VFCB-121. The mounting order is exactly the same for both models. The guard (A) (see fig.: 4.1) is first mounted on the back of the machine and there after as shown on the VFCB-motor. Dismount the blindstopper at the back of the machine and mount the connector (B). Dismount the switch on the machine without dismounting the wires. Lead the wire (C) through the connector (B) and mount the protection hose (D) on the connector (B). Mount the wires from the VFCB-exhaust unit on the switch (see wiring diagram). Mount the switch again. Dismount the blind guards on the cover or the beltarm and instead mount the guard (E) with exhaust connecting piece, also remember to mount the cork washer (F). Finally adjust the suction hoses (G) and mount the clip washers (H). VFCB-exhaust unit must before use be mounted with suction hoses on the suction connecting piece (I), which then must be connected with central exhaust unit. If the central exhaust unit has no cyclone, the exhaustion from the VFCB-exhaust unit must be connected to a cyclone, which then again is connected to the central exhaustion. If there is no central exhaustion, dust bags (J) can be mounted on the exhaust connecting unit (I). In case the VFCB-exhaust unit is mounted on the PSD 200 double grinder, the casted pipe bendings (K) can be used to mount the VFCB-exhaust unit on the grinding machine by what the guard (A) and the suction hoses (G) with accessories can be left out. Fig.: Maintenance of VFCB-exhaust unit Nothing on a VFCB-exhaust unit requires maintenance except that it is necessary to make sure that the suction hoses are intact and the suction channels are clear. 9

10 5 Spare parts list 5.1 Drawing of PSD 200 basic model Fig.: Spare parts list for PSD 200 basic model Pos.nr. Type Ident. Nr. 1 Distance pipe 30x20x Screw M6x20 CH Z Bearing end shield V O-ring 50x45x3 mm Wave spring 50x44x Bearing Z/C Cable 4x0.75mm² sort Cable lead-in PG Blind stop PG Stator housing Split pin ø4x Rotor cpl Bearing end shield H DISA switch 230 V DISA switch 440 V Skrew M4x Switch for DISA switch Earth cable

11 5.3 Split drawing of PSD 200 cover Fig.: Spare parts list for PSD 200 cover Pos.nr. Type Left Right 1 Eye shield Nut M Spring wave ring 5mm Screw M5x Cover PSD 200 inner Spring wave ring 5mm Screw M5x Wing nut M Spring Disc 6mm Tool rest Screw M6x Flange inner Grinding wheel 200x32xø Flange outer Nut M Screw M4x Cover PSD 200 outer

12 5.5 Split drawing of PSD 200 belt arm Fig.: Spare parts list for PSD 200 beltarm Pos. Nr. Type 1 Star handle Spring holder Tension spring Belt roller Belt arm Graphite pad Grinding belt 50x External grinding guard Screw M5x Wing nut spring Auto disc 5mm Tool rest Steel set bolt M6x Spring disc 5mm Machine screw M5x Distance piece Contact wheel Flange Nut M

13 5.7 Split drawing of VFCB-exhaust system for PSD 200 Fig.:

14 5.8 Spare parts list for VFCB-exhaust unit for PSD 200 Pos.nr. Type VFCB-220 VFCB Fan housing L. outer Screw M5x16 CH Z Washer DIM 5 Z Disc Ø5.5x26,5x Fan wheel VFCB alu Screw M6x16 Z Washer DIM 6 Z Fan housing L. inner V-Ring 16A Spring 5x5x Screw M8x16 Z Auto disc 5/16 Z Clamp for VFCB holder Fan housing R. inner Fan housing R. outer Power engine Thread piece PG Protection hose 18x13 400mm Dust bag Screw M4x16 w/round head Cork washer 120x Connecting piece exhaust Screw M5x10 CH Z Washer DIM 5 Z Tightening belt 68/ Suction hose Pedestal for PSD Table PSD 200* Water cup Disc ø13x24x Screw M12x40 Z Table for PSD 200 with beltarm or deburrer has nr.:

15 6 Technical data 6.1 Technical specifications Model PSD 200 PSD 200 w/beltarm Grinding belt - 50x1600 Motor effect in Watt Rpm Contact wheel - 200x50xø20 Grinding wheel 200x32xø20 - IP class Class F F Amp 1,9/3,3 1,9/3,3 Cos 0,81 0,81 Weight 38 The noise level for these machines varies from 76 db(a) (PSD 200/POD 5) to 88 db(a) (BO 50/5) according to the measuring directions in the Department for Work Safety and Health notice nr. 561 on devices of technical aids. Eye and ear protection must be worn during use of the above machines. 15

16 6.2 Wiring diagram PSD 200, BO 50/5 and POD 5 industrial grinding machines can be wired 3 x 400 V, 50/60 Hz or 3 x 230 V 50/60 Hz. Please see wiring diagrams below. Max. Voltage Min. Voltage Fig.:

17 6.3 Disaswich w/emergencstop 17

18 6.4 Guarantee If within 5 year of purchase this machine supplied by KEF A/S becomes defective due to faulty materials or workmanship we guarantee to repair or replace the machine or defective part or parts free of charge provided that: 1. The product is returned complete to one of our Service Branches or Official Service Agents. 2. The product has not been misused or carelessly handled and in particular has not been used in a manner contrary to the operating instructions. 3. Repairs have not been made or attempted by other than our own Service Staff or the staff of our Official Service Agents. 4. Documentary proof of purchase date is produced when the goods are handed in or sent for repair. 5. Wear parts are not covered by the warranty KEF A/S offers you five years guarantee on the electrical motor if the motor becomes defective or even burns-out within the first 5 years from date of invoice. 18

PSD 5 BO 50/5 POD 5 - PODA

PSD 5 BO 50/5 POD 5 - PODA KEF-MOTOR A/S Industrivej 3-9 DK 9460 Brovst Tel. +45 9823 6266 Fax. +45 9823 6144 25.04.12 Instruction Manual PSD 5 BO 50/5 POD 5 - PODA 5 Industrial Grinders Introduction You can connect your dual grinder

More information

7165 Dust Collector Owner s Manual

7165 Dust Collector Owner s Manual 7165 Dust Collector Owner s Manual Oliver Machinery M-7165 12/2016 Seattle, WA Copyright 2003-2017 info@olivermachinery.net www.olivermachinery.net CONTENTS IMPORTANT SAFETY RULES----------------------------------------------------------------

More information

3HP MOBILE CYCLONE DUST COLLECTOR MANUAL FILTER CLEANING MANUAL

3HP MOBILE CYCLONE DUST COLLECTOR MANUAL FILTER CLEANING MANUAL 3HP MOBILE CYCLONE DUST COLLECTOR MANUAL FILTER CLEANING MANUAL LAGUNA TOOLS 2072 Alton Parkway Irvine, California 92606 Ph: 800.234.1976 www.lagunatools.com 2018, Laguna Tools, Inc. LAGUNA and the LAGUNA

More information

5HP CYCLONE DUST COLLECTOR MANUAL

5HP CYCLONE DUST COLLECTOR MANUAL 5HP CYCLONE DUST COLLECTOR MANUAL LAGUNA TOOLS 2072 Alton Parkway Irvine, California 92606 Ph: 800.234.1976 www.lagunatools.com 2018, Laguna Tools, Inc. LAGUNA and the LAGUNA Logo are the registered trademarks

More information

2HP MOBILE CYCLONE DUST COLLECTOR MANUAL

2HP MOBILE CYCLONE DUST COLLECTOR MANUAL HP MOBILE CYCLONE DUST COLLECTOR MANUAL MANUAL FILTER CLEANING LAGUNA TOOLS 07 Alton Parkway Irvine, California 9606 Ph: 800.3.976 www.lagunatools.com 08, Laguna Tools, Inc. LAGUNA and the LAGUNA Logo

More information

hp Dust Collector With Vacuum Attachment

hp Dust Collector With Vacuum Attachment Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

IMPORTANT SAFETY RULES

IMPORTANT SAFETY RULES 1 IMPORTANT SAFETY RULES Wood working can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product.

More information

Operating Manual RS6 Pro

Operating Manual RS6 Pro Operating Manual RS6 Pro 510 HODGE, ST-LAURENT, QC H4N 2A4 TOLL FREE: 1-877-262-5801 ~ TEL.: 514-382-1140 ~ FAX: 514-382-8249 ~ www.dupliskate.com SET-UP REMOVE THE RS6 FROM THE SHIPPING SKIDS. REMOVE

More information

Thank You & Congratulations On Your Purchase of: ARBE Model # SS-206 Table Top Dust Collector

Thank You & Congratulations On Your Purchase of: ARBE Model # SS-206 Table Top Dust Collector Thank You & Congratulations On Your Purchase of: ARBE Model # SS-206 Table Top Dust Collector "The Most Powerful Dust Collector In Its Class... Guaranteed!" IMPORTANT INSTRUCTIONS DO NOT DISCARD I Thank

More information

Code UB-3300VECK Cyclone Extractor

Code UB-3300VECK Cyclone Extractor Code 210643 UB-3300VECK Cyclone Extractor AT&M: 16/01/2017 CONTENTS IMPORTANT SAFETY RULES-------------------------------------------------------------- 2 IMPORTANT SAFETY RULES FOR DUST COLLECTORS---------------------------

More information

Please read the instructions before operating the machine. Vänligen läs instruktionsboken innan maskinen används.

Please read the instructions before operating the machine. Vänligen läs instruktionsboken innan maskinen används. Safety Instruction Tormek Water Cooled Grinders run at a slow speed in water and are designed for maximum safety. However as with all machines there are some basic rules that must be followed to reduce

More information

Bench Grinder. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference.

Bench Grinder. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

OPERATING INSTRUCTIONS DUST EXTRACTOR FM300S

OPERATING INSTRUCTIONS DUST EXTRACTOR FM300S OPERATING INSTRUCTIONS DUST EXTRACTOR FM300S 0909 CONTENTS TECHNICAL DATA.1 UNPACKING AND CHECKING CONTENTS.2 ASSEMBLY..2 SAFETY RULES.5 WIRING DIAGRAM...6 PARTS DIAGRAM......8 PARTS LIST. 9 TECHNICAL

More information

D O U B L E A U G E R M O R TA R M I X E R OWNER S MANUAL

D O U B L E A U G E R M O R TA R M I X E R OWNER S MANUAL D O U B L E A U G E R M O R TA R M I X E R OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions

More information

Vacuum Presses Series

Vacuum Presses Series Vacuum Presses Series SVP1718 SVP SVP1718FL Operator manual Manufactured by: 1 Introduction The Vacuum Presses are compact, robust and sturdy machine designed for fast, complete vacuum forming work. It

More information

OWNER S OPERATING MANUAL DC-1200P DUST COLLECTOR

OWNER S OPERATING MANUAL DC-1200P DUST COLLECTOR OWNER S OPERATING MANUAL DC-1200P DUST COLLECTOR 1101 CONTENTS TECHNICAL DATA.1 UNPACKING AND CHECKING CONTENTS.2 ASSEMBLY..3 SAFETY RULES.9 WIRING DIAGRAM...10 PARTS DIAGRAM FOR DC-1200P.....11 PARTS

More information

BG6UL. 6 Inch Bench Grinder Assembly & Operating Instructions

BG6UL. 6 Inch Bench Grinder Assembly & Operating Instructions BG6UL 6 Inch Bench Grinder Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important information

More information

7140 Dust Collector Owner s Manual

7140 Dust Collector Owner s Manual 7140 Dust Collector Owner s Manual Oliver Machinery M-7140 09/2011 Seattle, WA Copyright 2003 info@olivermachinery.net www.olivermachinery.net CONTENTS ADDITIONAL SAFETY RULES FOR DUST COLLECTOR... 3 SAFETY

More information

Landis Fume Buster 3, 4 & 5 Foot

Landis Fume Buster 3, 4 & 5 Foot Landis Fume Buster 3, 4 & 5 Foot Operator Manual Manufactured by V 05/2018 INTRODUCTION The Landis Fume Buster is a durable machine designed to remove toxic airborn chemicals and odors from your work environment.

More information

DIE GRINDER INSTRUCTIONS IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL.

DIE GRINDER INSTRUCTIONS IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. DIE GRINDER STOCK No.57842 110V 57843 230V PART No.DG528 INSTRUCTIONS IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. GENERAL INFORMATION This manual

More information

1 supply. Belt Sander INSTRUCTION MANUAL. y::;:,' mm (3") MODEL 9900B. Specifications. DOUBLE INS ULATlO N. Continuous. Belt speed 1.

1 supply. Belt Sander INSTRUCTION MANUAL. y::;:,' mm (3) MODEL 9900B. Specifications. DOUBLE INS ULATlO N. Continuous. Belt speed 1. Belt Sander 76 mm (3") MODEL 9900B INSTRUCTION MANUAL DOUBLE INS ULATlO N Specifications Belt size Belt speed rating I Continuous (Input) y::;:,' supply Power cord 76 mm x 533 mm (3") x (2") 360m /min.

More information

ATD /8 Electric Drill

ATD /8 Electric Drill ATD-10538 3/8 Electric Drill Tool specifications: Rated Voltage: (V) 120 Rated Frequency: (Hz) 60 Rated current: (A) 3.3 No-load Speed: (RPM) 0-2700 Speed Selection: Yes Right/Left Rotation: Yes Chuck

More information

BG8SS. 8 Inch Slow Speed Bench Grinder with LED Lights Assembly & Operating Instructions

BG8SS. 8 Inch Slow Speed Bench Grinder with LED Lights Assembly & Operating Instructions BG8SS 8 Inch Slow Speed Bench Grinder with LED Lights Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This

More information

TCUT10UL 2.5 HP 10 Tile Saw Assembly & Operating Instructions

TCUT10UL 2.5 HP 10 Tile Saw Assembly & Operating Instructions TCUT10UL 2.5 HP 10 Tile Saw Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation and maintenance.

More information

XC-18. NOTE: *Machine shown without Lift-Up Safety Guard. This guard is included with machine. Machine should not be operated without this guard.

XC-18. NOTE: *Machine shown without Lift-Up Safety Guard. This guard is included with machine. Machine should not be operated without this guard. XC-18 NOTE: *Machine shown without Lift-Up Safety Guard. This guard is included with machine. Machine should not be operated without this guard. EXTREMA MACHINERY COMPANY, INC. PO BOX 1450, ALBANY, LOUISIANA

More information

Electric Lawn Rake GVM-600

Electric Lawn Rake GVM-600 Subject to change Electric Lawn Rake GVM-600 USER S MANUAL www.servotool.nl 0701-09 Art. no. VMM6001 Exploded view 2 1 4 3 4 9 5 7 8 6 Fig.1 Fig.2a 02 Gardenline Gardenline 19 Spare parts list No. Description

More information

Manual. Belt Sander BSL 115/E. ProxxonTools.com

Manual. Belt Sander BSL 115/E. ProxxonTools.com ProxxonTools.com Belt Sander BSL 115/E Manual 3080767 Conforms to ANSI/UL 60745-1 ANSI/UL 60745-2-4 Certified to CAN/CSA-C22.2 No. 60745-1-04 CAN/CSA-C22.2 No. 60745-2-4-04 Fig. 1 Fig. 2 Fig. 3 Fig. 4

More information

CYCLONETM ROTARY TUMBLER INSTRUCTION GUIDE

CYCLONETM ROTARY TUMBLER INSTRUCTION GUIDE Lyman CYCLONETM ROTARY TUMBLER INSTRUCTION GUIDE Visit our complete Lyman website at www.lymanproducts.com WARNING: This appliance is not intended for use by persons (including children) with reduced physical,

More information

SPECIFICATIONS FEATURES

SPECIFICATIONS FEATURES FEATURES Excellent for collecting the large chips which will drop into the garbage can before reaching the impeller. The filter bag filters out the remaining sawdust down to 5 microns. With the cyclone

More information

English Manual for Jewelry Casting and Investing The professional choice

English Manual for Jewelry Casting and Investing The professional choice English Manual for Jewelry Casting and Investing The professional choice QUICK START GUIDE: For thorough instructions, please review attached instructions. However, below, you will find a simplified start-up

More information

3-1/2 GALLON PARTS WASHER OPERATING INSTRUCTION AND PARTS MANUAL. Model # 4KTV9

3-1/2 GALLON PARTS WASHER OPERATING INSTRUCTION AND PARTS MANUAL. Model # 4KTV9 3-1/2 GALLON PARTS WASHER OPERATING INSTRUCTION AND PARTS MANUAL Model # 4KTV9 QUALITY GUARANTEE: Should a Westward product fail to perform satisfactorily due to defect or poor workmanship within one

More information

PS /2 Inch Angle Grinder Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.

PS /2 Inch Angle Grinder Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. PS07214 4 1/2 Inch Angle Grinder Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.

More information

DUST EXTRACTOR INSTRUCTION MANUAL. 550W (3/4 HP) INDUCTION MOTOR 1850W AUTOMATIC POWER OUTLET 65L COLLECTION BAG ø100mm X 2.

DUST EXTRACTOR INSTRUCTION MANUAL. 550W (3/4 HP) INDUCTION MOTOR 1850W AUTOMATIC POWER OUTLET 65L COLLECTION BAG ø100mm X 2. KNOW YOUR PRODUCT DUST EXTRACTOR 550W (3/4 HP) INDUCTION MOTOR 1850W AUTOMATIC POWER OUTLET 65L COLLECTION BAG ø100mm X 2.5M SUCTION HOSE INSTRUCTION MANUAL WARNING: Read all safety warnings and all instructions.

More information

CEMENT MIXER MODEL NO: CCM134L OPERATION & MAINTENANCE INSTRUCTIONS PART NO: GC0514

CEMENT MIXER MODEL NO: CCM134L OPERATION & MAINTENANCE INSTRUCTIONS PART NO: GC0514 CEMENT MIXER MODEL NO: CCM134L PART NO: 3400862 OPERATION & MAINTENANCE INSTRUCTIONS GC0514 INTRODUCTION Thank you for purchasing this CLARKE Cement Mixer. Before attempting to use this product, please

More information

FM300BC Dust Extractor

FM300BC Dust Extractor Code 501264 FM300BC Dust Extractor Axminster Tool Centre, Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PH axminster.co.uk CONTENTS TECHNICAL DATA.1 UNPACKING AND CHECKING CONTENTS.2 ASSEMBLY..3 SAFETY

More information

Thank You & Congratulations On Your Purchase of: ARBE Model # MD-205 Table Top Dust Collector

Thank You & Congratulations On Your Purchase of: ARBE Model # MD-205 Table Top Dust Collector Thank You & Congratulations On Your Purchase of: ARBE Model # MD-205 Table Top Dust Collector " The Most Powerful Dust Collector n ts Class... Guaranteed!" A R BC. t...,,,'.~ilme"fg.,nc. -, 54 AileD Blvd'.

More information

BENCH GRINDER WITH LIGHT AND WHEEL DRESSER MODEL NO: CBG8370L

BENCH GRINDER WITH LIGHT AND WHEEL DRESSER MODEL NO: CBG8370L BENCH GRINDER WITH LIGHT AND WHEEL DRESSER MODEL NO: CBG8370L PART NO: 6500532 OPERATION & MAINTENANCE INSTRUCTIONS LS0514 INTRODUCTION Thank you for purchasing this CLARKE Bench Grinder with light and

More information

150MM ELECTRIC EARTH BORER

150MM ELECTRIC EARTH BORER 150MM ELECTRIC EARTH BORER MODEL NO: CEA150 PART NO: 3400997 OPERATING & MAINTENANCE INSTRUCTIONS GC0915 INTRODUCTION Thank you for purchasing this CLARKE Electric Earth Borer designed for boring holes

More information

20-GALLON MOBILE PARTS WASHER OWNER S MANUAL

20-GALLON MOBILE PARTS WASHER OWNER S MANUAL 20-GALLON MOBILE PARTS WASHER OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in

More information

Cable Drum Machine. Operation Manual 110ES SERIES. Cleans 1 1/4" to 3" lines up to 25'

Cable Drum Machine. Operation Manual 110ES SERIES. Cleans 1 1/4 to 3 lines up to 25' Cable Drum Machine Operation Manual 110ES SERIES Cleans 1 1/4" to 3" lines up to 25' Used For: Sinks, Showers &Tub Drains WARNING - Read All Instructions, When Using Electric Tools, Basic Safety Precautions

More information

Ferm Bench Grinder FSMC-200/150. Art.nr Screwfix Art.nr Ferm BV P.O. Box AC Genemuiden NL

Ferm Bench Grinder FSMC-200/150. Art.nr Screwfix Art.nr Ferm BV P.O. Box AC Genemuiden NL UK Subject to change USER S MANUAL Document Ref: FSMC-200/150/14544/PMR35/issue 1/May 02 Copyright These instructions are the sole property of Ferm-Omega Tools and may not be reproduced Ferm Bench Grinder

More information

50 Litre Dust Collector

50 Litre Dust Collector Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

ASSEMBLY AND OPERATING INSTRUCTIONS 1HP DUST EXTRACTOR. FOX Model F50-841

ASSEMBLY AND OPERATING INSTRUCTIONS 1HP DUST EXTRACTOR. FOX Model F50-841 ASSEMBLY AND OPERATING INSTRUCTIONS 1HP DUST EXTRACTOR FOX Model F50-841 1 1hp Dust Extractor FOX MODEL F50-841 TABLE OF CONTENTS Safety instructions Page 3 Specific safety instructions for dust collectors.page

More information

User s Manual and Operating Instructions

User s Manual and Operating Instructions User s Manual and Operating Instructions Model Numbers: PT-18W-DDF-A, PT-20F-DDF-A, PT-20S-DDF, PT-24O-DDF, PT-24-DDF, PT-24-DDF-F, PT-30-DDF, PT-30P-DDF-A, PT-30P-DDF-AF READ AND SAVE THESE INSTRUCTIONS

More information

User s Manual and Operating Instructions

User s Manual and Operating Instructions User s Manual and Operating Instructions Model Numbers: CL-30P-DDF, CL-20F-DDF, CL-24O-DDF, CL-30-DDF READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Read and understand all of the directions in this manual

More information

BENCH GRINDER WITH LIGHT AND WHEEL DRESSER MODEL NO: CBG6250L

BENCH GRINDER WITH LIGHT AND WHEEL DRESSER MODEL NO: CBG6250L BENCH GRINDER WITH LIGHT AND WHEEL DRESSER MODEL NO: CBG6250L PART NO: 6500524 OPERATION & MAINTENANCE INSTRUCTIONS LS0514 INTRODUCTION Thank you for purchasing this CLARKE Bench Grinder with light and

More information

VARIABLE SPEED JIG SAW MODEL No. CJS350. MODEL No. CROS1 Part No OPERATING & MAINTENANCE INSTRUCTIONS

VARIABLE SPEED JIG SAW MODEL No. CJS350. MODEL No. CROS1 Part No OPERATING & MAINTENANCE INSTRUCTIONS VARIABLE SPEED JIG SAW MODEL No. CJS350 ROTARY ORBITAL Part No. 6460200 SANDER MODEL No. CROS1 Part No. 6462010 OPERATING & MAINTENANCE INSTRUCTIONS 0606 Thank you for purchasing this CLARKE Variable Speed

More information

English BT3600

English BT3600 www.blackanddecker.com 3 English BT3600 FIG. 1 FIG. 2 150mm BENCH GRINDER BT3600 GENERAL SAFETY RULES WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric

More information

ASSEMBLY AND OPERATING INSTRUCTIONS 3HP DUST EXTRACTOR. FOX Model F50-843

ASSEMBLY AND OPERATING INSTRUCTIONS 3HP DUST EXTRACTOR. FOX Model F50-843 ASSEMBLY AND OPERATING INSTRUCTIONS 3HP DUST EXTRACTOR FOX Model F50-843 1 3hp Dust Extractor FOX MODEL F50-843 TABLE OF CONTENTS Safety instructions Page 3 Specific safety instructions for dust collectors.page

More information

ASSEMBLY AND OPERATING INSTRUCTIONS PADDLE MIXER. FOX Model F V / 110V

ASSEMBLY AND OPERATING INSTRUCTIONS PADDLE MIXER. FOX Model F V / 110V ASSEMBLY AND OPERATING INSTRUCTIONS PADDLE MIXER FOX Model F7860 240V / 110V 1 Paddle Mixer FOX MODEL F7860 240V / 110V TABLE OF CONTENTS Safety instructions Page 3 Specifications Page 5 Environmental

More information

5.0 cu ft Electric Concrete Mixer

5.0 cu ft Electric Concrete Mixer Save This Manual for Future Reference 5.0 cu ft Electric Concrete Mixer Operator s Manual MODEL NUMBER YM0146 SERIAL NUMBER PURCHASE DATE Both model number and serial number may be found on the main label

More information

VARIABLE SPEED GRINDER OWNER S MANUAL R MANUAL VERSION SERIAL #

VARIABLE SPEED GRINDER OWNER S MANUAL R MANUAL VERSION SERIAL # R3.5 VARIABLE SPEED GRINDER SERIAL # MANUAL VERSION CONFORMS TO UL STD 763, NSF/ANSI STD 8 CERTIFIED TO CSA STD C22.2 #95 CONFORMS TO CE, IEC TESTED 2. Introduction WARNING: To limit risk of personal injury

More information

PORTABLE HAND POWER THREADER 1/2-2

PORTABLE HAND POWER THREADER 1/2-2 PORTABLE HAND POWER THREADER 1/2-2 Read this Operator s Manual carefully before using this tool. Failure to understand and follow the contents of this manual may result in electrical shock, fire and/or

More information

Mini-Rooter Operating Instructions

Mini-Rooter Operating Instructions Mini-Rooter Operating Instructions For 1-1/4 through 4 lines (30mm 100mm) Your Mini-Rooter is designed to give you years of trouble-free, profitable service. However, no machine is better than its operator.

More information

3.5-GALLON PARTS WASHER OWNER S MANUAL

3.5-GALLON PARTS WASHER OWNER S MANUAL 3.5-GALLON PARTS WASHER OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious

More information

Product Code: Cordless Patio Weed Sweeper INSTRUCTION MANUAL. Please retain for reference.

Product Code: Cordless Patio Weed Sweeper INSTRUCTION MANUAL. Please retain for reference. Product Code: 2036884 Cordless Patio Weed Sweeper INSTRUCTION MANUAL Please retain for reference. 1 Table of Contents: Safety Instructions 2 Product Description 3 Safety Symbols 3 Warnings 4-5 Parts breakdown

More information

INSTRUCTION MANUAL MODEL: 690E

INSTRUCTION MANUAL MODEL: 690E 1 INSTRUCTION MANUAL ALEKO Drywall Sander MODEL: 690E READ THROUGH CAREFULLY AND UNDERSTAND THESE INSTRUCTIONS BEFORE USE Visit our web site for more great products, parts and accessories: 2 3 4 5 6 Caution!

More information

PORTABLE HAND POWER THREADER 1/2-2

PORTABLE HAND POWER THREADER 1/2-2 PORTABLE HAND POWER THREADER 1/2-2 Read this Operator s Manual carefully before using this tool. Failure to understand and follow the contents of this manual may result in electrical shock, fire and/or

More information

DUST EXTRACTOR MODEL No: CDE1000

DUST EXTRACTOR MODEL No: CDE1000 DUST EXTRACTOR MODEL No: CDE000 Part No:64765 OPERATING & MAINTENANCE INSTRUCTIONS GC054 INTRODUCTION Thank you for purchasing this CLARKE Dust Extractor which is intended to keep work areas free from

More information

1/3 SHEET ORBITAL SANDER MODEL No. COS200

1/3 SHEET ORBITAL SANDER MODEL No. COS200 1/3 SHEET ORBITAL SANDER MODEL No. COS200 OPERATING & MAINTENANCE INSTRUCTIONS 1107 SPECIFICATIONS Elec. Supply... 230V 50Hz 1 ph Power Rating... 150 Watts Fuse Rating... 5 Amps No Load Speed... 10,000

More information

Leaf mulcher Trituradora de hojas Déchiqueteuse à feuilles. Pag 07 Pag 14 Pag 22 WG430. helpline NumBEr worX (9679)

Leaf mulcher Trituradora de hojas Déchiqueteuse à feuilles. Pag 07 Pag 14 Pag 22 WG430. helpline NumBEr worX (9679) Trituradora de hojas Déchiqueteuse à feuilles F ES Pag 07 Pag 14 Pag 22 helpline NumBEr 1-866-354-worX (9679) WG430 8 1 2 7 3 4 5 6 6 A B C a E1 E2 b F G H I J K1 K2 L1 L2 L3 L4 M1 f e d c d b M2 N a 6

More information

for Ultima-Tig and for Ultima-Tig-Cut

for Ultima-Tig and for Ultima-Tig-Cut User manual for Ultima-Tig and for Ultima-Tig-Cut Inelco Grinders A/S, Industrivej 3, DK-9690 Fjerritslev, Denmark 1/7 EU statement of compliance Manufacturer: INELCO GRINDERS A/S Industrivej 3 9690 Fjerritslev

More information

1HP Dust Collector. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference.

1HP Dust Collector. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

GRIND PRO DUAL OR DISC SANDER. Operator Manual

GRIND PRO DUAL OR DISC SANDER. Operator Manual GRIND PRO DUAL OR DISC SANDER Operator Manual 2 GRIND PRO DUAL OR DISC ORTHO-SANDER INTRODUCTION The Grind Pro Dual or Disc Sander is a compact, durable machine designed for fast, complete finishing work.

More information

GENERAL POWER TOOL SAFETY WARNINGS

GENERAL POWER TOOL SAFETY WARNINGS GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save

More information

GENERAL INFORMATION. INSTRUCTIONS FOR 160L 230V Cement Mixer

GENERAL INFORMATION. INSTRUCTIONS FOR 160L 230V Cement Mixer INSTRUCTIONS FOR 160L 230V Cement Mixer Stock No.17776 Part No.CM170 IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS PRODUCT. GENERAL INFORMATION These

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Power Mixer UT2204 DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Power Mixer UT2204 DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Power Mixer UT04 0078 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model UT04 No load speed (min - )

More information

Wet & Dry Bench Grinder

Wet & Dry Bench Grinder Wet & Dry Bench Grinder 200/150mm Instruction Manual 3 Year Replacement Warranty OZWDBG250WA! warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions

More information

User s Manual and Operating Instructions

User s Manual and Operating Instructions User s Manual and Operating Instructions Model Numbers: CL-36-BDF-A, CL-42-BDF-A, CL-48-BDF-A READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Read and understand all of the directions in this manual before

More information

Easy Rooter. Operating Instructions

Easy Rooter. Operating Instructions Easy Rooter Operating Instructions For 3" through 10" lines (75mm 250mm) Your Easy Rooter is designed to give you years of trouble-free, profitable service. However, no machine is better than its operator.

More information

SAFETY AND OPERATING MANUAL

SAFETY AND OPERATING MANUAL SAFETY AND OPERATING MANUAL Original instructions GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in

More information

Leaf Blower Vac 9242 Instructions for Use

Leaf Blower Vac 9242 Instructions for Use OPERATING CONTROLS 1. Wheel 2. Blower/Suction tube 3. Blower/Vacuum body 4. Auxiliary handle 5. Hole for belt hook 6. Shoulder belt 7. Switch trigger 8. Vacuum/Blower selector lever 9. Collection Bag CONTENTS

More information

VACUUM EXTRACTOR MODEL NO: CWVE1 OPERATING & MAINTENANCE INSTRUCTIONS PART NO: GC0916

VACUUM EXTRACTOR MODEL NO: CWVE1 OPERATING & MAINTENANCE INSTRUCTIONS PART NO: GC0916 VACUUM EXTRACTOR MODEL NO: CWVE1 PART NO: 6471168 OPERATING & MAINTENANCE INSTRUCTIONS GC0916 INTRODUCTION Thank you for purchasing this CLARKE Workshop Vacuum Extractor. Before attempting to use this

More information

English CNA-CNB. Centrifugal fans Installation and maintenance

English CNA-CNB. Centrifugal fans Installation and maintenance 916505-0 English CNA-CNB Centrifugal fans Installation and maintenance 916505-0 GB Centrifugal fans types CNA, CNB, CNA-M and CNB-M installation and maintenance 1. Application 2. Handling 2.1 Marking 2.2

More information

High-Velocity Floor Fan

High-Velocity Floor Fan High-Velocity Floor Fan Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions

More information

2000W HOT AIR GUN INSTRUCTIONS IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL.

2000W HOT AIR GUN INSTRUCTIONS IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. 2000W HOT AIR GUN STOCK No.64261 PART No.HG2000 INSTRUCTIONS IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. IMPORTANT: The heating wire element of

More information

20In. Oscillating Wall-Mount Fan. Owner s Manual

20In. Oscillating Wall-Mount Fan. Owner s Manual 20In. Oscillating Wall-Mount Fan Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety

More information

Instruction Manual. Model No. MT-988. Electric Snow Thrower

Instruction Manual. Model No. MT-988. Electric Snow Thrower Instruction Manual Model No. MT-988 Electric Snow Thrower IMPORTANT: Read and understand this manual before assembling or operating this Electric Snow Thrower. Improper use of Snow Thrower can cause severe

More information

Instructions for Use. Electric Pole Hedge Trimmer Input Power Tooth gap of cutter blade 16mm

Instructions for Use. Electric Pole Hedge Trimmer Input Power Tooth gap of cutter blade 16mm Voltage/Frequency 230V-240V a.c./ 50Hz Input Power 450W Tooth gap of cutter blade 16mm Strokes 1,600/min Noise emission value LWA 100 db(a) Hand / arm vibration a vhw < 2.5 m /s2 Total Length 1.9m-2.5m

More information

AZN ATEX INSTALLATION AND MAINTENANCE

AZN ATEX INSTALLATION AND MAINTENANCE ZerAx AZN ATEX INSTALLATION AND MAINTENANCE 924714-0 English 924714-0 GB ZerAx axial flow fans type AZN ATEX Installation and maintenance 1. Application 2. Handling 2.1 Marking 2.2 Weight 2.3 Temperature

More information

JASOPELS ROTATING FLESHING MACHINE 1-BEAM

JASOPELS ROTATING FLESHING MACHINE 1-BEAM USER MANUAL JASOPELS ROTATING FLESHING MACHINE 1-BEAM ITEM NO. 32200067 Our quality Your choice 2 www.jasopels.com TABLE OF CONTENTS About this document... 3 Declaration of Conformity... 6 Safety... 6

More information

SHOPSMITH DC-330L DUST COLLECTOR OWNER S MANUAL. For more information: For Question or Support: (937)

SHOPSMITH DC-330L DUST COLLECTOR OWNER S MANUAL. For more information:  For Question or Support: (937) SHOPSMITH OWNER S MANUAL For more information: www.shopsmith.com For Question or Support: (937) 890-5197 SHOPSMITH DC-330L DUST COLLECTOR 845620 TABLE OF CONTENTS 1. Safety... 2 2. Unpacking and Checking

More information

MN908 No. 282C Replaces 282B LB7013

MN908 No. 282C Replaces 282B LB7013 No. 282C Replaces 282B LB7013 Instruction Manual For Baldor Dust Control Units Models DC7, DC7 3, DC8, DC8 3, DC10, DC10 3, DC12, DC12 3 and DC14 3. For use on Grinders mounted to GA16 and GA20 pedestals

More information

Panel Fan Series Operators Manual (Galvanized and Polymer)

Panel Fan Series Operators Manual (Galvanized and Polymer) Panel Fan Series Operators Manual (Galvanized and Polymer) Galvanized Panel Fan with Three Wing Blade IMPORTANT: READ AND SAVE THESE INSTRUCTIONS Read all instructions carefully before attempting to assemble,

More information

DUST COLLECTOR KC-3105KWRC SEE PAGE 16 MODEL: KC-3105C INSTRUCTION MANUAL 1999 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.

DUST COLLECTOR KC-3105KWRC SEE PAGE 16 MODEL: KC-3105C INSTRUCTION MANUAL 1999 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. KC-3105KWRC SEE PAGE 16 DUST COLLECTOR MODEL: KC-3105C INSTRUCTION MANUAL COPYRIGHT C 1999 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. IMPORTANT INFORMATION THANK YOU FOR PURCHASING THIS KING CANADA

More information

SAFETY AND OPERATING MANUAL. 450W/46cm HEDGE TRIMMER JM450PHT

SAFETY AND OPERATING MANUAL. 450W/46cm HEDGE TRIMMER JM450PHT SAFETY AND OPERATING MANUAL 450W/46cm HEDGE TRIMMER JM450PHT GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may

More information

SAFETY AND OPERATING MANUAL

SAFETY AND OPERATING MANUAL SAFETY AND OPERATING MANUAL Random orbit sander WX655 2 3 1 9 4 5 8 6 7 A1 A2 10B 10A B C1 C2 D 11 E F E F G H1 H2 H3 H4 H4 GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all

More information

3 in 1 Garden Vacuum 9255 Instructions for Use

3 in 1 Garden Vacuum 9255 Instructions for Use Leaf Blower-Vac/Patio Cleaner Technical Specifications Model GY 8113 Rated voltage 230V Rated frequency 50Hz Rated power consumption 3000W Mains fuse(delayed action) 13A Speed 15000 rpm Max. blower air

More information

Roanoke 48 in Ceiling Fan Owner s Manual. Roanoke Ventilador de Techo de 1,22 m Manual del Propietario

Roanoke 48 in Ceiling Fan Owner s Manual. Roanoke Ventilador de Techo de 1,22 m Manual del Propietario 160 854 Roanoke 48 in Ceiling Fan Owner s Manual Roanoke Ventilador de Techo de 1,22 m Manual del Propietario 48 Roanoke Ceiling Fan by Hampton Bay Thank you for purchasing our ceiling fan. This product

More information

Grinding mill MISTRAL 50L (art. 650P)

Grinding mill MISTRAL 50L (art. 650P) Grinding mill MISTRAL 50L (art. 650P) USE AND MAINTENANCE MANUAL RIVER SYSTEMS SRL Via Marco Polo, 33-35011 Campodarsego (Padova) Italy Tel. +39-049-9202464 - Fax: +39-049-9216057 - e-mail: info@riversystems.it

More information

PWASH Gallon Parts Washer Assembly & Operating Instructions

PWASH Gallon Parts Washer Assembly & Operating Instructions PWASH20 20 Gallon Parts Washer Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Demolition Hammer HM0810TA DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Demolition Hammer HM0810TA DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Demolition Hammer HM080TA 00079 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model HM080TA Blows per

More information

TILE SAW RODIA 207RS OPERATING MANUAL

TILE SAW RODIA 207RS OPERATING MANUAL TILE SAW RODIA 207RS OPERATING MANUAL CAUTION Carefully read and understand all Safety and Operating Procedures prior to using the Rodia 207RS. Keep this Manual in a safe place for future reference. Contact

More information

Blower UB1100 UB1101 INSTRUCTION MANUAL

Blower UB1100 UB1101 INSTRUCTION MANUAL ENGLISH (Original instructions) INSTRUCTION MANUAL Blower UB00 UB0 004752 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

More information

ENGLISH (Original instructions) INSTRUCTION MANUAL. Belt Sander DOUBLE INSULATION. IMPORTANT: Read Before Using.

ENGLISH (Original instructions) INSTRUCTION MANUAL. Belt Sander DOUBLE INSULATION. IMPORTANT: Read Before Using. ENGLISH (Original instructions) INSTRUCTION MANUAL Belt Sander 990 99 00336 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model 990 99 Belt size 76 mm x

More information

Panel Fan Series Operators Manual (Galvanized and Polymer)

Panel Fan Series Operators Manual (Galvanized and Polymer) Panel Fan Series Operators Manual (Galvanized and Polymer) 52" Belt Drive, Galvanized Panel Fan with Three Wing Blade IMPORTANT: READ AND SAVE THESE INSTRUCTIONS Read all instructions carefully before

More information

Service Documentation Market Release 7/84. Braun Kitchen machine KM 32 B 4209 with lamp

Service Documentation Market Release 7/84. Braun Kitchen machine KM 32 B 4209 with lamp Market Release 7/84 Braun Kitchen machine KM 32 B 4209 with lamp 4209 Exploded Drawing BAG Rev: 7/84 4209 4209-2 Service Information BAG Rev: 12/88 4209 Pos. No. Part Description Part Number 1 Male drive

More information

DUST/CHIP EXTRACTOR OPERATING & MAINTENANCE. MODEL No. CDE7B INSTRUCTIONS. Part Part No

DUST/CHIP EXTRACTOR OPERATING & MAINTENANCE. MODEL No. CDE7B INSTRUCTIONS. Part Part No DUST/CHIP EXTRACTOR Part 6460200 MODEL No. CDE7B Part No. 6470305 OPERATING & MAINTENANCE INSTRUCTIONS 0305 -1- -14- -13- IMPORTANT Before commencing please check contents and advise immediately of any

More information

3-1/2 Gallon Parts Washer

3-1/2 Gallon Parts Washer 3-1/2 Gallon Parts Washer Model 38347 Assembly and Operating Instructions 3491 Mission Oaks Blvd., Camarillo, CA 93011 Copyright 1998 by Harbor Freight Tools. All rights reserved. No portion of this manual

More information

Technical Data. Name: ERIKA Automat fully automatic machine to divide and to round dough pieces of the same size

Technical Data. Name: ERIKA Automat fully automatic machine to divide and to round dough pieces of the same size AUTOMAT MANUAL 1 Technical Data Name: ERIKA Automat fully automatic machine to divide and to round dough pieces of the same size Type Divisions Dough Portions (in ounces) Plate Nos. 3 30 1.0 3.5 #35 4/40A

More information