Residential Application

Transcription

1 Residential Application

2 Technical Data Sheet Matrix Polyacryl Network Appearance Small light yellow/beige balls Surface Ceramic Template Surface Moisture Content 24 to 28% Density 1,18 to 1,22 Weight 650g/L Media Particle Size 550 to 750 µm Small Media Particles < 0,300 mm: maximum 3,0% Large Media Particles > 1,180 mm: maximum 5,0% Change in Volume Maximum 60% Capacity 1 Liter CWG Media for 3.0 gal/min water flow. Daily use Lifetime Media can be used 12 hours a day, no need for regeneration or back flushing when the direction water flow goes upwards. 5 years depending on the amount of chlorine in the water Operating Temperatures 41 F to 140 F PH Range 6.0 to 9.0 2

3 Considerations Temperature Range. 41û F to 149ûF PH Range 6.0 to 9.0 Chlorine... No greater than 3ppm Iron... No greater than.4ppm Hydrogen Peroxide(H2O2). No greater than.5ppm Manganese. No greater than 0.05 ppm Oil. Hydrogen Sulfide (H2S).. Polyphosphates Grains of Hardness. Must be removed prior to use with Must be removed prior to use with Must be removed prior to use with 100 grains (Any application over 25 grains call for technical support and specifications) General Life Span of Media... 5 years 3

4 Basic installation Notes system must be the last form of water treatment equipment installed with the exception of an RO unit or POU filter (Check Consideration Data sheet for more specific detail) Recommended to use a carbon pre-filter for municipal applications (carbon pre-filters reduces the negative effects of high chlorine on the media and lowest levels of iron.4ppm. ***Note: you must change out your carbon filter to keep proper flow rates ) Recommended that you soak the media for minutes before start up. This assures that the media is saturated with water and will not accumulate at the top the housing when filled with water. Do not apply phosphates or any other anti-scalents either before or after the system systems are only partly filled with media; systems must have an adequate freeboard Systems must use an upper slotted basket Systems must use a Spider Flexible Hub or Lateral or Enpress Vortech tank to ensure proper fluidization. (For larger tanks, use a hub and lateral with a garnet underbed operates in the UPFLOW mode ONLY!!!! The tank connections are normally opposite from the standard down flow configuration Recommended to use a flow restrictor that is sized to the proper tank and water flow (***Note: you want enough water flow for the proper sized system but you do not want too much water flow ) For additional information contact technical support or visit our website 4

5 Tank Size Required Media Hardness 25 GPG or Less (Liters) Residential Units Required Media Hardness GPG (Liters) Required Media Hardness GPG (Liters) Residential Specifications Max Flow Rate (GPM) 8X X X X X NOTES: Spider Flexible Hub and Lateral Distributor or Enpress Vortech tank must be used to ensure maximized fluidization Make sure to refer to the Considerations and Installation notes before install To convert parts per million to grains per gallon, divide by 17.1 For specifications not listed, contact our technical support team at or at inquiry@cwgusa.com Basic Municipal Residential System Diagram *The above diagram is only an example 5

6 Explain why the Filtersorb SP conditioner is not a traditional softener. Softener The classical water-softening unit operates on the basis of ion exchange; exchanging calcium and magnesium ions in water with an equivalent amount of sodium (Salt). When a water softener is used, the result is not only soft water, but also increased sodium content in the water supply. Additionally, these softening units require water for backwashing and common Brine water salt water for regeneration. For example, in order to regenerate 100 liters of softening resin, up to 25 kg of salt per regeneration cycle is required. This means an added costly expense of salt is incurred for each and every regeneration cycle. The water media acts as a catalyst by accelerating the transformation of the calcium and magnesium minerals into harmless Nano particles. When the inlet water goes into the water conditioner tank, the up flow pulls the water through the fluidized media which then acts as a catalyst and pulls the hardness minerals of calcium and magnesium out of the solution and then transforms these minerals into inactive Nano crystal particles. Because the hardness minerals have been transformed into Nano particles, these Nanoscopic particles make their way through plumbing systems without attaching on to pipes, fixtures, valves, or heating elements. is also a maintenance free system that does not require cost for salt, costs for water or for regeneration material. Visit our web site for more information on Nano Technology: Residential Q &A Can you explain the chemistry behind the media? CWG has embraced the cutting edge science of nanotechnology and through extensive research and development has developed the catalytic filtration media used to prevent and remove calcium scale. The overall filtration process of the is broken down into three phases. Phase One In the first phase, the calcium and magnesium is removed from the water. The catalytic surface of the Filtersorb media pulls the calcium and magnesium ions from the water and coverts these ions into harmless nano crystal particles. These nano crystals are so small that they are approximately one billionth of a meter; 100,000 times smaller than a single strand of hair. Phase Two In the second phase of the filtration process, the existing scale in the piping and hardware is removed. The nano crystal particles are neutral and are unable to attach to any surfaces, but due to their large surface area and nano structure, bind to the calcium ions in the scale, gradually breaking the grid structure of the calcium deposits. Over time, the calcium scale deposits within the pipes and equipment are completely removed. Phase Three In the third phase and final phase filtration process, a 3 to 5 micron protective corrosion later is formed. This layer forms because of the reaction of the nano surface of the crystals and the metallic surface of the pipes. This is comparable to the green layer of verdigris on a copper roof. As soon as the protective layer is formed it can no longer grow bigger, but it creates complete protection. 6

7 Will I feel and different when I shower? After the existing scale is completely dissolved, many customers have said that they feel a silk like feeling and their hair much cleaner than before the SP3 treatments. Bar soap is not recommended, but liquid body soap is preferred. Will I see any change in the laundry? After the existing scale is completely dissolved, your laundry will come out cleaner, feel softer, and last longer. What should I expect after installing a SP3 conditioner from my dishwasher? Dishwashers use water from the hot water side of plumbing and the water is extremely hot water and also extremely hot in the drying cycles when cleaning and drying the dishes. You may find unusual initial spotting because of the de-scaling taking place. You also may have existing excessive scale build inside the sidewalls and washing arms of the dishwasher. The best way to eliminate the excising scale in the dishwasher is to put a cup of white vinegar in the upper basket during the washing cycle for the first few weeks. You can also use citric acid instead of the white vinegar. This will help dissolve the existing scale in the washer arms and inside surface of the dishwasher. You may need to do this until all of the old scale in the plumbing is dissolved. Are there specific soaps that you should use? Also, when you have water going through the SP3 conditioner other than being used in the dishwasher cleaning cycle you can have the calcium crystals break down back into solution if you are using harsh dishwashing detergents that have low ph, high chlorine, and phosphates. Harsh detergents can breakdown the crystals and than can cause spotting on the dishes. Residential Q &A It will be important to reduce or soap usage as much as 50% and be sure to use Eco friendly dishwashing detergents. You may have to try several all natural dishwashing detergents to find the one that works best for your dishwasher Seventh Generation dishwashing powder which you can find at Target and Lemi-Shine which is available at Wall Mart are an examples of environmental detergents that works well with our media in the dishwasher. What should I expect after installing a SP3 conditioner in my shower and are there preparations required? Also in the bathrooms, over a few weeks you will see the existing scale slowly dissolve in the shower heads increasing water flow. Remember the calcium being treated is a nano size (one hundred thousandths of a human hair) and will be flowing easier down the sides of the walls and glass doors in the shower. We recommend that you first clean the shower from existing scale with a cleaning product that dissolves old scale that has built up before installation of the SP3 Conditioner system. One suggestion to use a product called CLR or products like this one. We then recommend that you coat the walls in the shower head with Rainx, a commercial product used for Automobile windshields. The Rainx allows the majority of the nano particles to be easily washed to drain. The few nano particles that are left can be easily wiped down because they no longer can adhere to the sides of the shower. Note: Rainx can also be used on all fittings to include the chrome. You can find Rainx at Wal-Mart or automobile stores. 7

8 Before & After Pictures Washing Chamber of a Large Air Conditioning System About six weeks after the installation of the Systems the calcium deposits were completely removed DVGW Testing Before and After Pictures The DVGW testing was conducted during a 3 week period; one test was without and the other test was conducted with. As you can see from the pictures worked optimally. 8