USER S MANUAL EUROPEAN SCRUB-PRO GOLF BALL CLEANSER

Size: px

Start display at page:

Download "USER S MANUAL EUROPEAN SCRUB-PRO GOLF BALL CLEANSER"

Melanie Heath
5 years ago
Views:

1 USER S MANUAL EUROPEAN SCRUB-PRO GOLF BALL CLEANSER Magnum Scrub-Pro Golf Ball Cleanser is made with a durable polyethylene body and a tubular steel powder coated frame. Features include scattered trim bristles for better cleaning of dimples, an oversized drain for quick and easy cleaning, and adjustable feet for leveling on various surfaces. The brush is reversible for longer life, and is easily removed. Ball cleaning capacity is,000 balls per hour. The tank holds 0 liters. The machine measures 9 cm wide x 0 cm high x cm deep, and weighs kg. Standard Golf Company 0 Nordic Drive Cedar Falls, IA 0 USA m o d e l nu m b e r 000 Phone: Fax:

0 Nordic Drive Cedar Falls, IA 0 USA www.standardgolf.com Phone: + 9-- Fax: + 9--9. Inspect the machine after removing from the shipping crate. Do not operate the machine if there is any damage.

DO NOT ATTEMPT TO USE MACHINE WITH A NON- GROUNDED POWER SOURCE.. Add 0 ml ( US ounces) of Standard Sparkleen golf ball cleaner to empty tank.

2 0 Nordic Drive Cedar Falls, IA 0 USA Phone: Fax: Inspect the machine after removing from the shipping crate. Do not operate the machine if there is any damage.. Attach basket to lid as shown.. Place machine on a hard, level surface. DO NOT OPERATE MACHINE IN STANDING WATER OR IN THE RAIN.. Plug machine into a 0V grounded receptacle. DO NOT ATTEMPT TO USE MACHINE WITH A NON- GROUNDED POWER SOURCE.. Add 0 ml ( US ounces) of Standard Sparkleen golf ball cleaner to empty tank. Fill the tank with approximately 0 liters of warm to hot water (approximately cm from the top). DO NOT USE LAUNDRY DETERGENTS, HOUSEHOLD CLEANERS, CHEMICAL SOLVENTS, OR ACIDS.. To operate machine: A. Close the tub lid, and fasten the rubber latches. B. Turn the switch to the ON position. C. Place a few balls in the basket to check for proper operation before filling the basket with balls.. If the machine jams, it will automatically shut off. To remove blockage: A. Turn the switch to OFF position, and unplug from power source. B. Open drum, and remove balls or jammed object. C. Wait approximately minutes, then reconnect machine to power source. IF THE JAM CANNOT BE CLEARED BY THE ABOVE PROCEDURE, CONSULT THE MAINTENANCE MANUAL FOR PROCEDURES FOR REMOVAL OF DRUM.

3 MAINTENANCE AND PARTS MANUAL FOR THE EUROPEAN SCRUB-PRO GOLF BALL CLEANSER REVISED JUNE 00 m o d e l nu m b e r 000

4 MAGNUM SCRUB-PRO WARRANTY Standard Golf Company warrants its products to free from defects in materials and workmanship within a period of one year from the date of purchase. Standard Golf s sole responsibility under this warranty shall be to repair, replace, or refund to its Distributor the price of the defective product or component. All such repairs, refunds and replacements are subject to such rules, terms and conditions and Standard Golf may promulgate from time to time. INITIAL INSPECTION Inspect the machine immediately after removing the outer portion of the shipping crate. If it is found detached or moved from the pallet, there is possibility of damage. Inspect the machine. If any damage is discovered, immediately notify the shipping carrier and take the appropriate action. BASKET INSTALLATION The MAGNUM SCRUB-PRO has been shipped from the manufacturer with the basket unassembled. Refer to BASKET & EXIT CHUTE ASSEMBLY (page ) for mounting directions. INSTALLATION AND HOOK-UP a) The MAGNUM SCRUB-PRO may be used outdoors; however it is recommended to place the machine on a hard surface and not have it set directly on the open ground. b) It is not necessary that the machine be perfectly level. The tub is designed to drain in the center of the tank, permitting efficient water drainage from off-level position. c) A drain extension can be attached to the ball valve. A standing drain pipe or fixture can be connected directly. d) Plug machine into a standard 0V, gounded wall receptacle or UL approved extension. Be careful to keep electrical power source clear of water. Warning: The SCRUB-PRO is designed with a grounded safety plug. DO NOT ATTEMPT TO DEFEAT ITS PURPOSE. Use of a plug adaptor or non-ground power source can result in shock or injury. INITIAL MACHINE START-UP ) Soap and Water Fill a. Put 0 ml of SPARKLEEN LIQUID DETERGENT into the empty tank. b. Fill the tank approximately cm from the top with warm to hot water. WARNING: Do not use laundry detergents, liquid cleaners, chemical solvents, or acids. Page

5 ) Test Cycle a. Make sure the tub is closed and the rubber latches are fastened. WARNING: Never operate machine with lid open or the rubber latches unfastened. b. With the tank properly filled, place an empty basket on the floor in front of the exit chute. c. Turn the machine ON using the ON/OFF switch (see diagram #). d. Place a few balls in the hopper. Observe and make sure the balls roll and enter smoothly through the ball entry trough (the leveling feet may need to be adjusted to help the ball enter the trough). The balls should exit the machine from the ball exit chute. The machine is equipped with an overload protector. In case of blockage, the machine will automatically shut OFF to prevent serious damage. Removing the drum may be necessary. To reset, turn ON/OFF switch to OFF position and disconnect from the power source, clear machine of blockage, wait five minutes, reconnect the power source and then turn ON again. e. Turn the machine OFF using the ON/OFF switch (see diagram #). Diagram # Page Diagram #

MAINTENANCE PROCEDURES a. Always turn the machine off and disconnect from power source before doing any maintenance. b. Always use the proper soap and water solution c.

6 MAINTENANCE PROCEDURES a. Always turn the machine off and disconnect from power source before doing any maintenance. b. Always use the proper soap and water solution c. Always turn the machine on before feeding hopper d. Monitor the flow of balls in the hopper for sticks, rocks, chunks of mud, golf tees, broken balls or any other debris, and remove as discovered. Foreign matter hinders the machine s cleaning ability. e. The SCRUB-PRO is designed to pass small debris through the drain slot on the bottom of the lower drum. Large objects must be removed by hand. f. Regularly remove the drum from washer to inspect from broken or cut balls, large debris, or other obstructions that may be lodged in the lower drum guides or drainage slot. The pillow block bearings are designed for ease in drum removal. To remove drum:. Rotate the drum until the coupler set is vertically aligned.. Remove the () / (M0) hex head bolts from each pillow block.. Pull the drum straight up and out of the lower tank. g. Exceptionally dirty or muddy balls should be cycled through the machine twice. h. Drain water after each use or when exceptionally dirty. i. Do not leave water in the tank. Standing water will accelerate deterioration of rubber cleaning surfaces. j. Hose down the inside of the machine after each use to clear the machine of dirt and debris. k. The SCRUB-PRO has been designed with () grease zerks located on the drum pillow blocks (see diagram below for locations). Page

0 Nordic Drive Cedar Falls, Iowa 0 USA Phone: + 9-- Fax: + 9--9 SCRUB-PRO BASKET & EXIT CHUTE ASSEMBLY 9 0 Key Number / Item Description / Quantity / Part Number Page 9 0 Basket #0- x.

7 0 Nordic Drive Cedar Falls, Iowa 0 USA Phone: Fax: SCRUB-PRO BASKET & EXIT CHUTE ASSEMBLY 9 0 Key Number / Item Description / Quantity / Part Number Page 9 0 Basket #0- x.0 Pan Head Phillips (M-0. x mm) Exit Chute /-0 x.00 Pan Head Phillips (M-.0 x mm).0 Lockwasher (M) Rubber Grommet.0 Flatwasher (M) #- x. Flat Head Machine Screw (M-0. x mm) Kick Stand Backing #- Acorn Nut (M-0.) Black Delrin Strap Hinge Kick Stand

0 Nordic Drive Cedar Falls, Iowa 0 USA Phone: + 9-- Fax: + 9--9 SCRUB-PRO DRUM & PILLOW BLOCK ASSEMBLY Key Number / Item Description / Quantity / Part Number Coiled

8 0 Nordic Drive Cedar Falls, Iowa 0 USA Phone: Fax: SCRUB-PRO DRUM & PILLOW BLOCK ASSEMBLY Key Number / Item Description / Quantity / Part Number Coiled Brush Coupler Set. SQ. x. Key Stock Pillow Block Drum Weldment. Lockwasher (M0) /- x. Hex Head Bolt (M0-.0 x 0 mm) #0- x. Hex Socket Setscrew FP (M-0. x 0 mm) Page

0 Nordic Drive Cedar Falls, Iowa 0 USA Phone: + 9-- Fax: + 9--9 SCRUB-PRO / EUROPEAN MAIN FRAME & MOTOR ASSEMBLY 9 0 0 9 Key Number / Item Description / Quantity / Part Number Page 9 0 9 0 /-0 x.

9 0 Nordic Drive Cedar Falls, Iowa 0 USA Phone: Fax: SCRUB-PRO / EUROPEAN MAIN FRAME & MOTOR ASSEMBLY Key Number / Item Description / Quantity / Part Number Page /-0 x. Hex Washer Head Cutting Screw.0 Lockwasher Main Frame. SQ. x. Key Stock Coupler Set #0- x. Hex Socket Setscrew FP 0v Motor & Power Cord /-0 x. Hex Head Bolt Motor Hood Weldment Electrical Switch & Box.0 Flatwasher /-0 Threaded Rod /-0 Acorn Nut Plastic Head Thumb Screw /- Hex Nut Leveling Feet End Cap Drain Holder Wheel Set Screw Shaft Collar L Bracket

0 Nordic Drive Cedar Falls, Iowa 0 USA Phone: + 9-- Fax: + 9--9 SCRUB-PRO TUB ASSEMBLY 9 0 Key Number / Item Description / Quantity / Part Number Page 9 0 Rubber Liner (. x 9.0) #0 x.

10 0 Nordic Drive Cedar Falls, Iowa 0 USA Phone: Fax: SCRUB-PRO TUB ASSEMBLY 9 0 Key Number / Item Description / Quantity / Part Number Page 9 0 Rubber Liner (. x 9.0) #0 x. Flat Head Phillips Sheet Metal Screw (M-0. x mm) Rubber Liner (. x.) Drum & Brush Assembly Rubber Liner (. x 0.) Liner/Guide Set (Plastic Guide) Tub (Top & Bottom) # x. Flat head Phillips Sheet Metal Screw (M-0. x 0 mm) Rubber Latch. Dia. Set Screw Shaft Collar Pivot Rod #0 x.0 Flat head Phillips Machine Screw (M-0. x mm) PVC Drain Assembly

11 0 Nordic Drive Cedar Falls, Iowa 0 USA Phone: Fax: SCRUB-PRO ELECTRICAL DIAGRAM Page

INSTALLATION and OPERATION BALL WASHER MODEL NO: BW-022

INSTALLATION and OPERATION BALL WASHER MODEL NO: BW-022 Easy Picker Golf Products, Inc. 415 Leonard Blvd. N., Lehigh Acres, FL 33971 PH: 239-368-6600 FAX: 239-369-1579 Service: 800-982-4653 SALES: 800-641-4653 www.easypicker.com salesdept@easypicker.com INSTALLATION