Air Conditioners. Technical Data FTXS-G

Transcription

1 Air Conditioners Technical Data I n d o o r u n i t s w w w. d a i k i n. e u FTXS-G

2 Air Conditioners Technical Data I n d o o r u n i t s w w w. d a i k i n. e u FTXS-G

3 Indoor Units R-410A FTXS-G TABLE OF CONTENTS FTXS-G 1 Features Specifications Technical Specifications Electrical Specifications Dimensional drawing & centre of gravity Dimensional drawing Centre of gravity Piping diagram Wiring diagram Wiring diagram Sound data Sound pressure spectrum Split Sky Air Indoor Units 1

4 t i y n k r t o 0- i o 1 ld 4 n pt- FI Indoor Units R-410A FTXS-G 1 Features U S A G S X RS ECONO mode decreases power consumption so that other appliances that need large power supply can be used Night set mode saves energy by preventing overcooling or overheating during night time Powerful mode can be selected for rapid cooling or heating Whisper quiet operation: down to 22dBA sound pressure level (Only for FTXS 20,25,35,42,50G) Indoor / outdoor unit silent operation: "Silent" buttons on the remote control lower the operation sound of the indoor and/or outdoor unit by 3dBA Night quiet mode automatically reduces the operation sound of the outdoor unit by 3dBA during nighttime (multi outdoors in cooling mode only) (Only for FTXS 20,25,35,42,50G) 3D air flow combines vertical and horizontal auto-swing to circulate a stream of warm/cool air right to the corners of even large spaces 2 area intelligent eye: air flow is sent to the area in a room where no person is detected Energy saving during stand by mode: reduction of energy from 10W to 2W Weekly timer: allows to program the unit on a weekly basis Comfort mode reassures draught free operation Powerful mode can be selected for rapid cooling or heating Titanium apatite photocatalytic air purification filter absorbs microscopic particles, decomposes odours and even deactivates bacteria and viruses 5 steps optional (integrated titanium apatite) 2 Split Sky Air Indoor Units

5 Indoor Units R-410A FTXS-G 2 Specifications 2-1 Technical Specifications FTXS20G2V1B FTXS25G2V1B FTXS35G2V1B FTXS42G2V1B FTXS50G2V1B Casing Colour White Dimensions Packing Height mm Width mm Depth mm Unit Height mm Width mm Depth mm Weight Unit kg Packed Unit kg Heat Exchanger Dimensions Length mm Nr of Rows Fin Pitch mm Nr of Stages Tube type ø6.35 Hi-XU Fin Type ML fin (Multi louvre) Fan Type Cross flow fan Air Flow Rate High m³/min Medium m³/min Low m³/min Silent Operation m³/min High m³/min Medium m³/min Low m³/min Silent Operation m³/min High cfm Medium cfm Low cfm Silent Operation cfm High cfm Medium cfm Low cfm Silent Operation cfm Fan Motor Model KFD A Number of steps 5 steps, silent and auto Motor Speed (cooling) High rpm 1,150 1,150 1,370 1,310 1,390 Medium rpm ,090 1,170 1,230 Low rpm ,020 1,060 Silent Operation rpm Speed (heating) High rpm 1,200 1,220 1,370 1,410 1,440 Medium rpm 1,030 1,030 1,160 1,230 1,270 Low rpm ,050 1,090 Silent Operation rpm ,000 Fan Motor Output (high) W Sound Power High dba Sound Pressure High dba Medium dba Low dba Silent Operation dba Sound Power High dba Sound Pressure High dba Medium dba Low dba Silent Operation dba Refrigerant Type R-410A Piping connections Liquid (OD) Diameter (OD) mm Gas Diameter (OD) mm Drain Diameter (OD) mm Heat Insulation Both liquid and gas pipes Split Sky Air Indoor Units 3

6 Indoor Units R-410A FTXS-G 2 Specifications 2-1 Technical Specifications FTXS20G2V1B FTXS25G2V1B FTXS35G2V1B FTXS42G2V1B FTXS50G2V1B Air Filter Removable/washable/Mildew proof Air direction control Right, Left, Horizontal, Downward Temperature control Microcomputer control Standard Titanium apatite photocatalytic air purification filter Accessories Quantity Operation manual Quantity Installation manual Quantity Wireless remote control Quantity Batteries Quantity Remote control holder Quantity Indoor unit fixing screws Quantity Mounting plate Quantity Technical Specifications FTXS60GV1B FTXS71GV1B Casing Colour White Dimensions Packing Height mm Width mm 1,145 1,145 Depth mm Unit Height mm Width mm 1,050 1,050 Depth mm Weight Unit kg Packed Unit kg Heat Exchanger Dimensions Length mm Nr of Rows 2 2 Fin Pitch mm Nr of Stages Tube type ø7 Hi-XD Fin Type ML fin (Multi louver) Fan Type Cross flow fan Air Flow Rate High m³/min Medium m³/min Low m³/min Silent Operation m³/min High m³/min Medium m³/min Low m³/min Silent Operation m³/min High cfm Medium cfm Low cfm Silent Operation cfm High cfm Medium cfm Low cfm Silent Operation cfm Fan Motor Model ARW3001DA Number of steps 5 steps, silent and auto 4 Split Sky Air Indoor Units

7 Indoor Units R-410A FTXS-G 2 Specifications 2-1 Technical Specifications FTXS60GV1B FTXS71GV1B Motor Speed (cooling) High rpm 1,330 1,410 Medium rpm 1,170 1,220 Low rpm 1,010 1,040 Silent Operation rpm Speed (heating) High rpm 1,360 1,520 Medium rpm 1,200 1,330 Low rpm 1,040 1,150 Silent Operation rpm 950 1,040 Fan Motor Output (high) W Sound Power High dba Sound Pressure High dba Medium dba Low dba Silent Operation dba Sound Power High dba Sound Pressure High dba Medium dba Low dba Silent Operation dba Air Filter Removable/washable/Mildew proof Air direction control Right, Left, Horizontal, Downward Temperature control Microcomputer control Standard Titanium apatite photocatalytic air purification filter Accessories Quantity 2 Operation manual Quantity 1 Installation manual Quantity 1 Infrared remote control Quantity 1 Batteries Quantity 2 Remote control holder Quantity 1 Indoor unit fixing screws Quantity 2 Mounting plate Quantity Electrical Specifications FTXS20G2V1B FTXS25G2V1B FTXS35G2V1B FTXS42G2V1B FTXS50G2V1B Power Supply Name V1 Phase 1~ Frequency Hz Voltage V Current Nominal running A current (RLA) A Wiring connections For Power Supply Quantity Electrical Specifications FTXS60GV1B FTXS71GV1B Power Supply Name V1 Phase 1~ Frequency Hz 50 Voltage V Current Nominal running A current (RLA) A Wiring connections For Power Supply Quantity 3 for power supply, 4 for interunit wiring (Earth wire included) Split Sky Air Indoor Units 5

8 Indoor Units R-410A FTXS-G 3 Dimensional drawing & centre of gravity 3-1 Dimensional drawing FTXS20-42G The mark ( ) shows piping direction Air flow (Indoor) Rear Left Right Including mounting plate 30 Min Space for performance Front panel fixed screws (inside) 50 Min Space for maintenance Name plate Terminal block with earth terminal REQUIRED SPACE 50 Min Space for maintenance Bottom Flaps Signal transmitter Signal receiver Model name plate Up/down (Automatic), dry Intelligent eye sensor Operation lamp Timer lamp Intelligent eye lamp Indoor unit ON/OFF switch Room temp. thermistor (Inside) BLADE ANGLES Fan Gas pipe Ø9.5 CuT (The length of pipe outside the unit: about 350) Liquid pipe Ø6.4 CuT (The length of pipe outside the unit: about 400) Drain hose (Connecting part I.D. Ø14 O.D. Ø18 The hose length of outside the unit is approx. 465) INFRARED REMOTE CONTROL (ARC452A3) FTXS50G The mark ( ) shows piping direction Right/left (automatic) Air flow (Indoor) Wall hole for embedded piping Ø65 hole STANDARD LOCATIONS OF WALL HOLES Wall hole Ø65 hole 3D058919A Rear Left Right Including mounting plate 30 Min Space for performance Front panel fixed screws (inside) 50 Min Space for maintenance Name plate Terminal block with earth terminal REQUIRED SPACE 50 Min Space for maintenance Bottom Flaps Signal transmitter Signal receiver Model name plate Up/down (Automatic), dry Intelligent eye sensor Operation lamp Timer lamp Intelligent eye lamp Indoor unit ON/OFF switch Room temp. thermistor (Inside) BLADE ANGLES Fan Gas pipe Ø12.7 CuT (The length of pipe outside the unit: about 350) Liquid pipe Ø6.4 CuT (The length of pipe outside the unit: about 400) Drain hose (Connecting part I.D. Ø14 O.D. Ø18 The hose length of outside the unit is approx. 465) INFRARED REMOTE CONTROL (ARC452A3) Right/left (automatic) Wall hole for embedded piping Ø65 hole STANDARD LOCATIONS OF WALL HOLES Wall hole Ø65 hole 3D058920A 6 Split Sky Air Indoor Units

9 Indoor Units R-410A FTXS-G 3 Dimensional drawing & centre of gravity 3-1 Dimensional drawing FTXS60GV The mark shows piping direction Air flow (indoor) (For performance and maintenance) Left Rear Rear Right (Including installation plate) Min. 30 (Space for performance) Model name plate Terminal block with earth terminal (inside) Min. 50 (Space for maintenance) REQUIRED SPACE Min. 50 (Space for maintenance) Bottom Signal transmitter Front grille fixing screws (inside) Flaps Signal receiver Model name plate BLADE ANGLES Intelligent eye sensor Operation lamp Timer lamp Intelligent eye lamp Indoor unit on/off switch Room temp. thermistor (inside) Horizontal blade (automatic) Dry Gas pipe ø12.7 CuT (the length of pipe outside the unit: about 430) Liquid pipe ø6.4 CuT (the length of pipe outside the unit: about 480) Drain hose for VP13 (connecting part I.D. 14.0, O.D. 18.0) (The hose length of outside the unit: about 530) Infrared remote control (ARC452A3) Fan Vertical blade (automatic) Wall hole for embedded piping ø 80 hole STANDARD LOCATIONS OF WALL HOLES Wall hole ø 80 hole 3D FTXS71GV The mark shows piping direction Air flow (indoor) (For performance and maintenance) Left Rear Rear Right (Including installation plate) Min. 30 (Space for performance) Model name plate Terminal block with earth terminal (inside) Min. 50 (Space for maintenance) REQUIRED SPACE Min. 50 (Space for maintenance) Bottom Signal transmitter Front grille fixing screws (inside) Flaps Signal receiver Model name plate BLADE ANGLES Intelligent eye sensor Operation lamp Timer lamp Intelligent eye lamp Indoor unit on/off switch Room temp. thermistor (inside) Horizontal blade (automatic) Dry Gas pipe ø15.9 CuT (the length of pipe outside the unit: about 430) Liquid pipe ø6.4 CuT (the length of pipe outside the unit: about 480) Drain hose for VP13 (connecting part I.D. 14.0, O.D. 18.0) (The hose length of outside the unit: about 530) Infrared remote control (ARC452A3) Fan Vertical blade (automatic) Wall hole for embedded piping ø 80 hole STANDARD LOCATIONS OF WALL HOLES Wall hole ø 80 hole 3D Split Sky Air Indoor Units 7

10 Indoor Units R-410A FTXS-G 3 Dimensional drawing & centre of gravity 3-2 Centre of gravity FTXS20-50G 4D059112B FTXS60-71GV 4D Split Sky Air Indoor Units

11 4 Piping diagram Indoor Units R-410A FTXS-G FTXS20-42G INDOOR UNIT 6.4CuT Heat exchanger Field piping 6.4CuT Cross flow fan Thermistor on heat exch. Field piping 9.5CuT 9.5CuT Fan motor Refrigerant flow 4D058897C FTXS50G INDOOR UNIT 6.4CuT Heat exchanger Field piping 6.4CuT Cross flow fan Thermistor on heat exch. Field piping 12.7CuT 9.5CuT Fan motor Refrigerant flow 4D058898C Split Sky Air Indoor Units 9

12 4 Piping diagram Indoor Units R-410A FTXS-G FTXS60GV Indoor unit (7.9 CuT) Heat exchanger Thermistor on heat exch. Field piping Cross flow fan (6.4 CuT) Field piping (12.7 CuT) Fan motor (12.7 CuT) Refrigerant flow 4D040081V FTXS71GV Indoor unit (7.9 CuT) Heat exchanger Thermistor on heat exch. Field piping Cross flow fan (6.4 CuT) Field piping (15.9 CuT) Fan motor (12.7 CuT) Refrigerant flow 4D040082T 10 Split Sky Air Indoor Units

13 5 Wiring diagram 5-1 Wiring diagram FTXS20-50G Indoor Units R-410A FTXS-G WIRING DIAGRAM FIELD WIRING RECTIFIER OUTDOOR TRANSMISSION CIRCUIT CAUTION Note that operation will restart automatically if the main power supply is turned off and than back on again. INTELLIGENT EYE SENSOR INFRARED REMOTE CONTROL SIGNAL RECEIVER INDOOR FG F1U H1P~H3P M1F M1S~M3S PCB1~PCB4 R1T, R2T S1~S49 S1W X1M : Frame ground : Fuse : Pilot lamp : Fan motor : Swing motor : Printed circuit board : Thermistor : Connector : Operation switch : Terminal switch : Protective earth 3D058246B FTXS60-71GV Field wiring LED1 H1P LED2 H2P LED3 H3P Transmission circuit Outdoor CAUTION Note that operation will restart automatically if the main power supply is turned off and then back on again. Intelligent eye sensor infrared remote control Signal receiver Indoor FG Frame ground R1T,R2T Thermistor F1U Fuse S1~S49 Connector H1P~H3P Pilot lamp SW1 Operation switch M1F Fan motor X1M Terminal strip M1S, M2S Swing motor Protective earth PCB1~PCB4 Printed circuit board 3D Split Sky Air Indoor Units 11

14 6 Sound data Indoor Units R-410A FTXS-G 6-1 Sound pressure spectrum FTXS20G COOLING FTXS20G HEATING 3D D Operation differs with operation and ambient conditions. 4 Operation differs with operation and ambient conditions. FTXS25G COOLING FTXS25G HEATING 3D059556B 3D059556B 4 Operation differs with operation and ambient conditions. 4 Operation differs with operation and ambient conditions. 12 Split Sky Air Indoor Units

15 6 Sound data Indoor Units R-410A FTXS-G 6-1 Sound pressure spectrum FTXS35G COOLING FTXS35G HEATING 3D059557C 3D059557C 4 Operation differs with operation and ambient conditions. 4 Operation differs with operation and ambient conditions. FTXS42G COOLING FTXS42G HEATING 3D059558B 3D059558B 4 Operation differs with operation and ambient conditions. 4 Operation differs with operation and ambient conditions. Split Sky Air Indoor Units 13

16 6 Sound data Indoor Units R-410A FTXS-G 6-1 Sound pressure spectrum FTXS50G COOLING FTXS50G HEATING 3D059559B 3D059559B 4 Operation differs with operation and ambient conditions. 4 Operation differs with operation and ambient conditions. FTXS60GV Octave band sound pressure level db (0 db = μ bar) Octave band sound pressure level db (0 db = μ bar) Octave band center frequency - IEC (Hz) Octave band center frequency - IEC (Hz) Scale 1 Over All (db): (B,G,N is already rectified) 2 Measuring place: measure in anechoic room. 3 Operation differs with operation and ambient conditions. 4 Location of microphone. JISC9612 The operation measuring method is in accordance with JISC Hz V (H) (L) A Scale 1 Over All (db): (B,G,N is already rectified) 2 Measuring place: measure in anechoic room. 3 Operation differs with operation and ambient conditions. 4 Location of microphone. JISC9612 The operation measuring method is in accordance with JISC Hz V H L A D051227D 14 Split Sky Air Indoor Units

17 6 Sound data Indoor Units R-410A FTXS-G 6-1 Sound pressure spectrum FTXS71GV Octave band sound pressure level db (0 db = μ bar) Octave band sound pressure level db (0 db = μ bar) Octave band center frequency - IEC (Hz) Octave band center frequency - IEC (Hz) Scale 1 Over All (db): (B,G,N is already rectified) 2 Measuring place: measure in anechoic room. 3 Operation differs with operation and ambient conditions. 4 Location of microphone. JISC9612 The operation measuring method is in accordance with JISC Hz V (H) (L) A Scale 1 Over All (db): (B,G,N is already rectified) 2 Measuring place: measure in anechoic room. 3 Operation differs with operation and ambient conditions. 4 Location of microphone. JISC9612 The operation measuring method is in accordance with JISC Hz V (H) (L) A D051225D Split Sky Air Indoor Units 15

18 Daikin s unique position as a manufacturer of air conditioning equipment, compressors and refrigerants has led to its close involvement in environmental issues. For several years Daikin has had the intention to become a leader in the provision of products that have limited impact on the environment. This challenge demands the eco design and development of a wide range of products and an energy management system, resulting in energy conservation and a reduction of waste. Daikin Europe N.V. is participating in the EUROVENT Certification Programme. Products are as listed in the EUROVENT Directory of Certified Products. The present publication is drawn up by way of information only and does not constitute an offer binding upon Daikin Europe N.V.. Daikin Europe N.V. has compiled the content of this publication to the best of its knowledge. No express or implied warranty is given for the completeness, accuracy, reliability or fitness for particular purpose of its content and the products and services presented therein. Specifications are subject to change without prior notice. Daikin Europe N.V. explicitly rejects any liability for any direct or indirect damage, in the broadest sense, arising from or related to the use and/or interpretation of this publication. All content is copyrighted by Daikin Europe N.V.. Daikin products are distributed by: Naamloze Vennootschap - Zandvoordestraat 300, B-8400 Oostende - Belgium BE RPR Oostende EEDEN CD 05/10 Copyright Daikin Prepared in Belgium by Lannoo ( a company whose concern for the environment is set in the EMAS and ISO systems. Responsible Editor: Daikin Europe N.V., Zandvoordestraat 300, B-8400 Oostende