Upompe Primeflo XP7 chemical self-priming centrifugal pumps

Transcription

1 Upompe Primeflo XP7 chemical self-priming centrifugal pumps 1

2 Design Introduction: These Upompe Primeflo XP7 self-priming pump are heavy-duty design for rugged application and constructed to handle corrosive, abrasive and other aggressive fluids, as well as those liquids which must remain free of metallic contamination. Upompe Primeflo XP7 pumps are available in a wide selection of thermoplastics and in ANSI/DIN, self-priming, close-coupled and integral pump/shaft motor designs. This heavy-duty, Primeflo XP7 self-priming, centrifugal pump handles flows up to 85m 3 /hr, making it ideal for acid transfer, sump and tank evacuation, and emergency overload pumping. It is often specified for in-line pump service where headroom prevents the use of vertical pumps, and other applications where self-priming from depths to 15 feet (4.6 m) may be required. As with all Upompe Primeflo XP7 pumps, have no metal components are in contact with the fluid being handled. Even the large diameter steel shaft is isolated from the fluid by a thick sectioned thermoplastic/ptfe sleeve. No metallic contamination is possible. Features: 1. Installed in corrosive, pure and contaminated media in the chemical, pharmaceutical, petrochemical, metal processing, waste water and disposal plants. 2. Impeller, shaft & casing are PTFE/PFA/Teflon liner, No metal contact. 3. Impellers are made with thermoplastic/ptfe material, injection molded with an embedded dynamically balanced metal shaft. 4. Insert with radial vanes. It shall be of semi-open vane design with keyway for mounting on shaft to assure positive drive. 5. Impeller type available from closed to semi opened. 6. Impellers are design with back vanes to offset axial thrust 7. Build with standard in grease lubrications. Optional in oil bath system 8. Dimension to EN /ISO Upompe Primeflo pumps are design with heavy duties bearing pedestal which allow for reduced shaft deflection and long bearing life, especially for low flow rate, high head and high density. 10. Upompe Primeflo XP7 Teflon liner pumps are design with internal and external mechanical seal. Type mechanical seal choose from Crane, AES, John crane, ChemZip and Chesterton. 11. Direct coupled and compact-mono block is available 12. Flange standard can be drilled to ANSI B16.5, JIS & BS. 13. Flow rate up to 85 m3/hr. 14. Pressure up to 50m 15. Back Pull Out Design 16. Operating temperature range from -10 C to + 90 C. Optional for temperature up to 135 C are available 17. Please contact local agent for suction lift for temperature more than 40 degree C. 2

3 Applications: Chemical transfer Corrosive liquids handling Self-priming Plating Plant Waste water transfer Con acid handling Small Solid handling Chemical Plant 1. PTFE mold Impeller with embedded metallic shaft 2. Teflon Bellow Seal with Sic Versa Sic seal face 3. Site installation for pumping HCL 37% 4. Shop alignment check before delivery 5. Waste plant installation for HNO3 transfer 6. Con Acid Transfer Plant 7. Mixed chemical waste transfer 3

4 Pump Model Figure Number Series Model Body material Impeller material Shaft material Seal type Seal material Impeller type Flange std Special code HTS- 1 Sic Vs Sic -3 Closed - L Thread - 0 Primeflo XP 7 XXXX PTFE lining -F PTFE lining -F SS Tungs Vs Tungs - 4 Semi open - E JIS - 1 SS Mechanical seal - M Sic Vs Tungs- 5 Open - P ANSI -2 Flouroplastic -X Flouroplastic -X PTFE lined -4 Non seal - 6 Special - Z GB - 3 Special - 7 DIN - 4 X General pumps performance table Model Suction size, mm Discharge Flow, m3/hr Head, m Power, kw Revolutions, rpm NPSH, m Suction lift, m * Above data is performance is based on clear liquids at 20 degree C. * Upompe reserved all right to change it specifications from time to time without prior notice * Standard model are for liquid maximum temperature are up 80 degree C. Optional PFA lining for temperature up to 135 degree C, upon request 4

5 Installations Dimensions, Direct coupled type Model L f W H h1 Inlet, mm n-d Outlet, mm n-t ' ' ' ' Note: Above Dimensions are with factory cast type of base plate, for local C-Channel pump based, please refer to local agents. Design, Dimensions & specifications subjected to change without prior notice. Please contact local agent for more details or sales@upompe.com 5