F60235N/NE-F60265N/NE-F60285N/NE NO-FROST UPRIGHT DEEP FREEZER SERVICE MANUAL

Transcription

1 F60235N/NE-F60265N/NE-F60285N/NE NO-FROST UPRIGHT DEEP FREEZER SERVICE MANUAL SERVICE MANUAL NO 1 January 11

2 1. Content 2. SAFETY PRECAUTIONS TECHNICAL SPECIFICATIONS PRODUCT INSTALLATION PRODUCT USE: PRODUCT USE: GENERAL OPERATION PRINCIPLE COMPONENTS LIST SERVICE FUNCTION TEST FAILURE CODES ELECTRIC CIRCUIT / CONNECTION / E-CARD DIAGRAMS EXPLODED DRAWINGS January 11

3 2. SAFETY PRECAUTIONS F60235N/NE-F60265N/NE-F60285N/NE NO-FROST UPRIGHT DEEP FREEZER This product is designed for domestic use. It should not be used outdoors. It is not appropriate to use it outdoor even if the place is covered with a roof. General safety Vapor and vaporized cleaning materials should never be used in cleaning and defrosting processes of refrigerator. In such cases, the vapor may get in contact with the electrical parts and cause short circuit or electric shock. Never use the parts on refrigerator such as the door and drawer as a means of support or step. You may cause the product to tip over or parts of it get damaged. Do not use electrical devices inside the refrigerator. Do not damage the cooling circuit, where the refrigerant is circulating, with drilling or cutting tools. The refrigerant that might blow out when the gas channels of the evaporator, pipe extensions or surface coatings are punctured may cause skin irritations and eye injuries. Do not cover or block the ventilation holes on refrigerator with any material. In case of any failure or during a maintenance or repair work, disconnect refrigerator s mains supply by either turning off the relevant fuse or unplugging the appliance. Do not pull by the cable when pulling off the plug. Do not use mechanical devices or other means to accelerate the defrosting process, others than those recommended by the manufacturer. Exposing the product to rain, snow, sun and wind is dangerous with respect to electrical safety. Never plug the refrigerator into the wall outlet during installation. Otherwise, risk of death or serious injury may arise. Intended use of the product is to preserve foods; it should never be used for other purposes. Rating plate containing product's technical specifications is in the inner left part of the product. Connecting the product to electric energy saving systems is risky as it may cause damage on the product. If the product is equipped with blue light, the light should not be looked into by optical appliances. In products with mechanical control (thermostat), wait for 5 min. to re-plug the product if it is unplugged. Power cable and plug should not be damaged when moving the refrigerator. To avoid risk of fire, the cable should not be kinked or put under heavy things. Do not touch the plug with wet hands when plugging the product. The product should not be plugged if the receptacle is loose. Water should not be sprayed directly on inner or outer parts of the product to avoid safety risks. Flammable pressurized sprays should not be sprayed near the product to avoid risk of fire or explosion. Containers with liquid inside should not be placed on top of the product. Spilling water on an electrical component may cause electric shocks or risk of fire. Products that need a precise temperature control (vaccines, heat-sensitive medicine, scientific materials, etc.) should not be kept in the refrigerator. 3 January 11

4 Refrigerator should be disconnected if it is not going to be used for a long time. Any problem in the cable insulation may cause fire. Dirt and dusts on tip of the electric plug must be cleaned; otherwise, they may cause risk of fire. The product may move when level adjustment feet of the product do not stand on the floor well. If the product has a door handle, the product must not be pulled by the handle, because the handle may be forced out. Care should be paid as there is risk of squeezing hands or feet between the movable parts inside the product. When you need to operate the refrigerator next to another refrigerator, leave at least 8 cm distance between two refrigerators. If you leave a shorter distance, condensation may arise on the side walls of the refrigerator. Water mains pressure must not be below 1 bar. Water mains pressure must not be above 8 bars. Use only potable water. HCA Warning If the product is equipped with a cooling system that contains R600a: This gas is flammable. Therefore, pay attention to not damaging the cooling system and piping during usage and transportation. In the event of damage, keep the product away from potential fire sources that can cause the product catch a fire and ventilate the room in which the unit is placed. Ignore the warning if the product is equipped with a cooling system that contains R134a. You can see the gas used in production of the product on the rating plate that is located on the left inner part of it. Never dispose the product in fire. Things to be done for energy saving Do not leave the doors of the refrigerator open for a long time. Do not put hot food or drinks in the refrigerator. Do not overload the refrigerator so that the air circulation inside of it is not prevented. Do not install the refrigerator under direct sunlight or near heat emitting appliances such as ovens, dishwashers or radiators. Please recommend that food items must be kept in closed containers. In order to load maximum amount of food in refrigerator's freezer compartment, place the food onto the wire shelves instead of the drawer and remove the upper cover. Maximum power consumption with maximum amount of food as described above has been measured and indicated on the energy label. Depending on the shape of the food to be frozen, there is no inconvenience in using the drawers and upper shelf cover. 4 January 11

5 3. TECHNICAL SPECIFICATIONS Please see product's instructions on Manusoft for the latest version of technical specifications. Here, the instructions are for reference only. For F60235NE/F60235N; Ü.T No: UT For F60265NE/F60265N; Ü.T No: UT For F60285NE/F60285N; Ü.T No: UT January 11

6 6 January 11

7 7 January 11

8 8 January 11

9 9 January 11

10 10 January 11

11 11 January 11

12 12 January 11

13 13 January 11

14 14 January 11

15 15 January 11

16 16 January 11

17 17 January 11

18 18 January 11

19 19 January 11

20 4. PRODUCT INSTALLATION F60235N/NE-F60265N/NE-F60285N/NE NO-FROST UPRIGHT DEEP FREEZER 4.1 FIRST INSTALLATION After unpacking, please take the following into consideration for the installation of refrigerator: 1. Is the interior of the refrigerator dry and can the air circulate freely in the rear of it? 2. You can install the 2 plastic wedges as illustrated in the figure. Plastic wedges will provide the required distance between the refrigerator and the wall in order to allow the air circulation. (The illustrated figure is only an example and does not match exactly with your product.) 3. Plug the refrigerator into the wall outlet. 4. You will hear a noise as the compressor starts up. The liquid and gases sealed within the refrigeration system may also give rise to noise, even if the compressor is not running and this is quite normal. 5. Front edges of the refrigerator may feel warm. This is normal. These areas are designed to be warm to avoid condensation. 6. Keep refrigerator away from heat sources, humid places and direct sunlight. 7. There must be appropriate air ventilation around the refrigerator in order to achieve an efficient operation. If the refrigerator is to be placed in a recess in the wall, there must be at least 5 cm distance with the ceiling and at least 5 cm with the wall. If the floor is covered with a carpet, the product must be elevated 2.5 cm from the floor. 8. Place the refrigerator on an even floor surface to prevent jolts. 20 January 11

21 Adjusting the feet: If the refrigerator is not level, you can level it by turning the front feet as illustrated in the figure below. The corner where the foot exists is lowered when you turn it in the direction of black arrow and raised when you turn it in the opposite direction. Temperature Setting: For the models for which a position is assigned, it is recommended to operate on position 3 in the first installation and on position -20 for the models in display. 21 January 11

22 4.2 SERVICE: REMOVING EVAPORATOR COVER: When servicing evaporator, fan, de-frost heater or drain heater; evaporator cover should be removed as shown below: General View 22 January 11

23 Remove the plugs by means of a suitable screwdriver. Remove upper screws 23 January 11

24 Pull out the upper cover Remove the screws of lower cover 24 January 11

25 Pull out the lower cover To service the sockets, remove the socket cover 25 January 11

26 Sliding it down, release from the tabs. Socket connections 26 January 11

27 To service control card, remove card box cover 27 January 11

28 Compressor area RIGHT WRONG Make sure that drain flap is installed on drain hole 28 January 11

29 SERVICING DRAIN HEATER: There is a foil type heater positioned in PU at drain area at the bottom of cabin. When this heater requires service, foil type service drain heater will be installed by using the service socket in socket box. You can check if this heater in PU works properly by means of Ohm meter as shown below: If drain heater does not work, service heater should be affixed as shown below: Heater tongue should be inserted in drain hole. 29 January 11

30 In socket box, drain service socket is positioned as shown. 30 January 11

31 IMPORTANT: When re-assembling the product, plated wire shelf must always be installed on the uppermost shelf where fan is located, in order to ensure proper air circulation. It must not be interchanged with other wire shelves. 31 January 11

32 5. PRODUCT USE: F60235N/NE-F60265N/NE-F60285N/NE NO-FROST UPRIGHT DEEP FREEZER User manual must be read before use and indicated warnings and caution items should be observed. These products feature no-frost system and de-frost is automatically performed. Please see user manual for other details. 32 January 11

33 6 GENERAL OPERATION PRINCIPLE The product is an NF upright deep freezer. Refrigeration is achieved by means of passing the air, which is absorbed by the fan on the uppermost part, through the evaporator located behind the cabin. Air temperature sensor on the upper right corner controls the temperature. Air guiding plates on the uppermost shelf serve for proper air circulation and their position is critical. The product performs de-frost periodically in a certain algorithm. Defrosted water accumulates in evaporating container above the compressor. If quick freeze function is activated, the product compressor achieves maximum refrigeration by operating at 100% capacity for the determined period (>24h). If the product's door is not opened for a long time, the product steps into energy saving mode without compromising performance. 33 January 11

34 7. COMPONENTS LIST IMPORTANT!!: For the latest list of servicing materials, please check manusoft; this list is for reference only. F60235N/NE-F60265N/NE-F60285N/NE NO-FROST UPRIGHT DEEP FREEZER 34 January 11

35 F60265NE / F60235NE SERVICE LIST NO STOCK DEFINITION UNIT QTY SERVICE REF. NO TERM BUTTON/ELECTRONIC-ARÇP1 ON BODY HAND PLATE(60CM/SIEVE/WITHOUT BUTTON LOWER HINGE ASSY UPPER HINGE ASSY (DIFFUSION) ADJUSTABLE FEET [LONG (PLS+CIV) B-650] DOUBLE INLET DRYER (10 gr) DRAIN FLAP ADJUSTABLE FEET ASSY [SHORT (PLS+CIV) B-650] REAR WEDGE (NATUREL-SNT). KMP S(NS 1114 Y/R600/ _50/JIAXİPERA) TERMINAL COVER JlAXlPERA COMPRESSOR BUFFER COMPRESSOR WASHER (U-INNER PRODUCT) POWER CABLE ASSY _2150 COMBO UNIT(JIAXPERA) NU1114Y/NS1114Y PTC RELAY (QP3-12A)J1AXPERA THERMIC SHIELD (B40-120)NU1114Y/NS1114Y CAPACITOR ASSY (4uF B5/270/6.3) P2 ON BODY PRINTED FRONT COVER GR/B575/WHITE EVA COVER PLUG/B-990/995 FRZ.PIPE INS. SPONGE/B-570/575 COMP.COND. ASSY F60232NE/B-575 PLS.WASHER(1.5 MMARÇ-P1) UPPER HINGE PIN(LINE 2001) SERVICE PIPE EVA.CABI/NU/NS(FIREPROOF MATR.-LARGE VOLUME) PANEL PLUG (ARÇ-P1) ADJUSTABLE FEET PLUG (ARÇ-P1) CABLE HOLDER WHEEL(NATUREL) WHEEL PIN (50MM) 60 CM REAR FOOT (753,763,775,765,785) GROUNDING CABLE ASSY ( _4.8) PU DOOR GR-DIF/B575/WITHOUT POCKET/MAGNET/TKSZ BEKO( SINGLE LETTER LOGO 90 MM ) HARD BIG HINGE HOUSING (NATURAL) DOOR SEAL GR B-570/575/ WHITE/HARD B-290/570/575 DR SEAL(ARCP1) ICEBOX (ARÇ-P1) (TS/NEW) F60235NE/F60265NE/FRZ.WIRE SHELF BYG_ICE BOX TRAY WITH BAG ASSY B760 ARCP1 FLAP HANDLE (RIGHT/ARÇ-P1) SMALL DRAWER BODY/ARÇ P1/DRILLED B764 CARD COVER ASSY F60235NE/F60265NE PLATED FRZ.WIRE SHELF FLAP ASSY WITH BAG.( ) B-555/565/575 DISPLAY CARD ON/OFF WIRE SHELF (B-570/575/THIN) SENSOR HOUSING COVER WIRE FAN PROTECTION B-777 UL PRESS ASSY (FNE BEKO EU) HINGE COVER RIGHT (ARÇ P1/DIF) HINGE COVER LEFT (ARÇ P1) CABLE HOLDER JIAXPERA RIGHT HOLE PLUG (LG/ARÇ-P1) COMPLETE EOH HANDLE ASSY/B /DIF(RAL9006M EVA FAN ASSY B-576/566 ROHS_ HINGE HOUSING-TOE BOARD-ARÇ-P1 STOPPER PLATE(DIFFUSION) REAR SUPPORT (ARÇ-P1) EOH BODY COVER/B-570/575/DlFFUSION ANTI-VACUUM EXTERNAL PART ANTI-VACUUM INTERNAL PART ANTI-VACUUM BALL PART/B_570/2 PRINTED DRAWER COVER ASSY/250mm/DlF SETTING BUTTON/B762/ RAL7037) PRINTED FLAP ASSY (B-570/575 DİF BLUE) PRINTED FLAP ASSY (B-570/575/MIRROR PRINTING DIF SOCKET HOUSING FRONT COVER BITUM-TE 150YT FREEZER UPPER EVAPORATOR COVER FREEZER LOWER EVAPORATOR COVER (B575) ISOLATION PLATE COMP_WOT_NF_EVAP_ASSY_F60265NE DOOR HAND PLATE MENT.COVER/LEFT/ARÇ-P1/DIF. FRZ.PIPE MIS.RUBBER(NOISE DAMPER) PLUG/HEATER_BR/4.76 WOT_NF_EVA_PIPE_F60265NE STEEL WIRE(WOT/1.9x297mm) COATED STEEL PIPE DIA 7.93*0.7MM * 1 M M 4.76 uncoated steel pipe M PRINTED DRAWER COVER ASSY WITH BAG/DIF BLUE DRAWER BODY/250 mm/hips/arcp1/delikl DRAWER BODY/190 mm/hips/arcp1/delikl FLAP HANDLE (LEFT/ARÇ-P1) 35 January 11

36 8. SERVICE FUNCTION TEST 8.1. ARÇELİK NEW APPEARANCE DISPLAY Images (in the lit status) and meanings of all display icons are provided below. -24, -22, -20 and -18 showing the refrigerator's temperature lights up continuously. The set temperature value is indicated by an arrow. ecofuzzy warning economy quick freeze refrigerator off display off 36 January 11

37 Service Test Steps 1. Press SW3 and SW4 buttons concurrently for 3 seconds. A short buzzer sound will be heard and service test mode will be activated. All icons turn on for 0.5 seconds and turn off for 0.5 seconds alternately. 2. Once any button is pressed; a long buzzer sound will be heard; version and revision information can be read on the display. Version and revision are indicated with Qfreeze animated LEDs. Version and revision numbers are indicated alternately for 2 seconds each. Refrigerator off icon lights up when the version number is shown on the display; animated LEDs for Qfreeze light up on the basis of the Number Reading Table in Appendix 1 to indicate the revision number. Display off icon lights up when the version number is shown on the display; animated LEDs for Qfreeze light up on the basis of the Number Reading Table in Appendix 1 to indicate the revision number. VERSION 1 REVISION 14 INDICATION 37 January 11

38 3. Press any button to proceed to the Sensor temperatures indication step. Sensor temperatures are indicated by means of Qfreeze animated icons. Refrigerator has two sensors. Namely; Freezer Eva Sensor and Freezer Air Sensor. Freezer Eva Sensor and Freezer Air Sensor values are alternately indicated on the display for 2 seconds. When displaying the Freezer Air Sensor temperature value: Icon -18 lights up Qfreeze icons light up as in the table in Appendix 1 to display the sensor temperature. If the sensor temperature value is negative, then the top-most arrow lights up; if it is positive then the second top-most arrow lights up. EXAMPLE: Numerical value 22 as per table in Appendix 1 Numerical value 11 as per table in Appendix 1 Negative value Positive value Freezer Air Sensor Temperature Indicated Freezer Air Sensor Temperature Indicated Freezer Air Sensor Temperature = -22 C Freezer Air Sensor Temperature = +11 C 38 January 11

39 Following display images occur during open circuit or short circuit errors. Freezer Air Sensor Open Circuit Freezer Air Sensor Short Circuit 39 January 11

40 When displaying the Freezer Eva Sensor temperature value: Icon -20 lights up Qfreeze icons light up as in the table in Appendix 1 to display the sensor temperature. If the sensor temperature value is negative, then the top-most arrow lights up; if it is positive then the second top-most arrow lights up. Numerical value 17 as per table in Appendix 1 Numerical value 16 as per table in Appendix 1 Negative value Positive value Freezer Eva Sensor Temperature Indicated Freezer Eva Sensor Temperature Indicated Freezer Eva Sensor Temperature = -17 C Freezer Eva Sensor Temperature = 16 C 40 January 11

41 Following display images occur during open circuit or short circuit errors. F60235N/NE-F60265N/NE-F60285N/NE NO-FROST UPRIGHT DEEP FREEZER Freezer Eva Sensor Open Circuit Freezer Eva Sensor Short Circuit 41 January 11

42 4. After the Temperature Indication step, relevant components can be activated or deactivated by pressing SW1, SW2 and SW3 buttons. (If Sensor failure exists; no component is activated within 15 minutes after service test starts.) 4.1 If SW1 button is pressed, warning icon lights up and compressor is activated. If SW1 button is pressed again, compressor is deactivated and warning icon disappears. If the SW1 button is pressed repeatedly, compressor will switch into protection mode and will not be activated. 4.2 If SW2 button is pressed, Ecofuzzy icon lights up and Fan is activated. If SW2 button is pressed again, fan is deactivated and Ecofuzzy icon disappears. 4.3 If SW3 button is pressed, Economy icon lights up and Defrost Heater is activated. If SW3 button is pressed again, Defrost Heater is deactivated and Economy icon disappears. 42 January 11

43 Compressor active Fan active Heater active Notes: Compressor and Fan active Compressor and Heater active Compressor, Fan and Heater active >> When SW3 and SW4 buttons are pressed for 3 seconds or the appliance remains in service test for 30 minutes without any action, it exits the service test mode. >> If the door is opened at any time during the service test, then -24 icon alternately flashes ON and OFF for 0.5 seconds 43 January 11

44 APPENDIX-1 NUMBER READING TABLE Temperatures that are indicated by turning on/off the Qfreeze/QFridge icons can be read from the following table. Dark coloured boxes indicate that the snow icon is turned on and light coloured boxes indicate that it is turned off. 44 January 11

45 8.2. BEKO NEW APPEARANCE DISPLAY Images (in the lit status) and meanings of all display icons are provided below. -24, -22, -20 and -18 showing the refrigerator's temperature lights up continuously. The set temperature value is indicated by an arrow. ecofuzzy warning economy quick freeze refrigerator off display off 45 January 11

46 Service Test Steps If SW1 and SW2 buttons are pressed concurrently for 3 seconds, a short buzzer sound will be heard and service test mode will be activated. All icons turn on for 0.5 seconds and turn off for 0.5 seconds alternately. Once any button is pressed; a long buzzer sound will be heard; version and revision information can be read on the display. Version and revision are indicated with Qfreeze animated LEDs. Version and revision numbers are indicated alternately for 2 seconds each. Refrigerator off icon lights up when the version number is shown on the display; animated LEDs for Qfreeze light up on the basis of the Number Reading Table in Appendix 1 to indicate the revision number. Display off icon lights up when the version number is shown on the display; animated LEDs for Qfreeze light up on the basis of the Number Reading Table in Appendix 1 to indicate the revision number. VERSION 8 REVISION 2 INDICATION 46 January 11

47 3. Press any button to proceed to the Sensor temperatures indication step. Sensor temperatures are indicated by means of Qfreeze animated icons. Refrigerator has two sensors. Namely; Freezer Eva Sensor and Freezer Air Sensor. Freezer Eva Sensor and Freezer Air Sensor values are alternately indicated on the display for 2 seconds. When displaying the Freezer Air Sensor temperature value: Icon -18 lights up Qfreeze icons light up as in the table in Appendix 1 to display the sensor temperature. If the sensor temperature value is negative, then the top-most arrow lights up; if it is positive then the second top-most arrow lights up. EXAMPLE: Numerical value 22 as per table in Appendix 1 Negative value Numerical value 11 as per table in Appendix 1 Positive value Freezer Air Sensor Temperature Indicated Freezer Air Sensor Temperature Indicated Freezer Air Sensor Temperature = -22 C Freezer Air Sensor Temperature = +22 C 47 January 11

48 Following display images occur during open circuit or short circuit errors. Freezer Air Sensor Open Circuit Freezer Air Sensor Short Circuit 48 January 11

49 When displaying the Freezer Eva Sensor temperature value: Icon -20 lights up Qfreeze icons light up as in the table in Appendix 1 to display the sensor temperature. If the sensor temperature value is negative, then the top-most arrow lights up; if it is positive then the second top-most arrow lights up. Numerical value 17 as per table in Appendix 1 Numerical value 16 as per table in Appendix 1 Negative value Positive value Freezer Eva Sensor Temperature Indicated Freezer Eva Sensor Temperature Indicated Freezer Eva Sensor Temperature = -17 C Freezer Eva Sensor Temperature = 16 C 49 January 11

50 Following display images occur during open circuit or short circuit errors. Freezer Eva Sensor Open Circuit Freezer Eva Sensor Short Circuit 50 January 11

51 4. After the Temperature Indication step, relevant components can be activated or deactivated by pressing SW2, SW3 and SW4 buttons. (If Sensor failure exists; no component is activated within 15 minutes after service test starts.) 4.1 If SW3 button is pressed, warning icon lights up and compressor is activated. If SW3 button is pressed again, compressor is deactivated and warning icon disappears. If the SW3 button is pressed repeatedly, compressor will switch into protection mode and will not be activated. 4.2 If SW4 button is pressed, Ecofuzzy icon lights up and Fan is activated. If SW4 button is pressed again, fan is deactivated and Ecofuzzy icon disappears. 4.3 If SW2 button is pressed, Economy icon lights up and Defrost Heater is activated. If SW2 button is pressed again, Defrost Heater is deactivated and Economy icon disappears. 51 January 11

52 Compressor active Fan active Heater active Compressor and Fan active Compressor and Heater active Compressor, Fan and Heater active Notes: >> When SW1 and SW2 buttons are pressed for 3 seconds or the appliance remains in service test for 30 minutes without any action, it exits the service test mode. >> If the door is opened at any time during the service test, then -24 icon alternately flashes ON and OFF for 0.5 seconds each. 52 January 11

53 APPENDIX-1 NUMBER READING TABLE Temperatures that are indicated by turning on/off the Qfreeze/QFridge icons can be read from the following table. Dark coloured boxes indicate that the snow icon is turned on, light coloured boxes indicate that it is turned off. 53 January 11

54 8.3. BEKO ELECTRONIC LED INDICATOR (with BDC card) F60265NE TRAINING DOCUMENT (with BDC-Electronic card) PRODUCTION TEST DOOR CLOSED If any sensor failure exists during production test, the refrigerator won't operate for 15 minutes (compressor and heater) If no error occurs during production test when the door is closed and frz_air sensor temperature is not higher than 10 C, production test goes as shown below. Door Closed COOL OPERATION If no error occurs during production test when the door is closed and frz_air sensor temperature is not higher than 10 C, production test goes as shown below. Time (sec) Door Closed WARM OPERATION If any errors occur during production test when the door is closed, none of the components operates for 15 minutes. Compressor starts to operate 15 minutes later. Time (sec) MALFUNCTION Time (sec) 54 January 11

55 F60265NE TRAINING DOCUMENT (with BDC-Electronic card) PRODUCTION TEST / DOOR OPEN If any sensor failure exists during production test, the refrigerator won't operate for 15 minutes (compressor and heater) If no error occurs during production test when the door is open and frz_air sensor temperature is not higher than 10 C, production test goes as shown below. Door open COOL OPERATION Time (sec) If no error occurs during production test when the door is open and frz_air sensor temperature is not higher than 10 C, production test goes as shown below. Door open WARM OPERATION Time (sec) If any errors occur during production test when the door is open, none of the components operates for 15 minutes. Compressor starts to operate 15 minutes later. MALFUNCTION Time (sec) 55 January 11

56 F60265NE TRAINING DOCUMENT (with BDC-Electronic card) FIRS ENERGIZING STATUS Door closed Door open VERSION REVISION CONTROL Step 1 When the product is energized for the first time, version number appears in seven segment. Step 1 When the product is energized for the first time, version number appears in seven segment. MAGNET CONTROL Step 2 After version detail appears in seven segment, all LEDs light up and seven segment disappears. Step 2 After version detail appears in seven segment, set value in seven segment starts to flash. NORMAL OPERATION Step 3 After all LEDs have lighted up for a certain time, only green light remains Step 3 After all LEDs have lighted up for a certain time, only green light remains and set value appears. 56 January 11

57 PUTTING THE PRODUCT IN SERVICE TEST F60265NE TRAINING DOCUMENT (With BDC-electronic board) SERVICE TEST If the product is not deenergised, the test takes 30 minutes; if it is deenergised during the test, the test is terminated. frz_eva and frz_air sensor temperature values are expected to be close to each other when the product is energised for the first time. Points to check during the service test: 1. Check whether the version number is Check the Frz-eva and Frz-air sensor temperature values (sensor temperature values must be close to each other when the product is energised for the first time.) 3. There are certain indicators that should be on or off in seven segment display and among the LED indicators Check whether there is any event contrary. The way to put the product in service test/door OPEN The way to put the product in service test/door CLOSED n Step 1: Press and hold the button with a snow-flake symbol on it right after the product is energised. You will see the below display when you press the button. Step 1: Press and hold the button with a snowflake symbol on it right after the product is energised. You will see the below display when you press the button. SEVEN SEGMENT DISPLAY AND LED INDICATOR CONTROL Step 2: When you release the button with a snowflake symbol on it, service test starts and following display appears. Step 2: When you release the button with a snowflake symbol on it, service test starts and following display appears. VERSION REVISION CONTROL Step 3: When you press the button with a snowflake symbol on it once again during the service test, version number will appear on the service test display. Step 3: When you press the button with a snowflake symbol on it once again during the service test, version number will appear on the service test display. SENSOR TEMPERATU RES AND LED INDICATOR CONTROL Step 4: When you press the button with a snowflake symbol on it for once while the version number is being displayed during the service test, first the frz_eva sensor (red) will illuminate on the LED indicator and the temperature value of this sensor will appear on the seven segment display; and then, the frz_air sensor (orange) will illuminate on the LED indicator and the temperature value of this sensor will appear on the seven segment display. This cycle continues until the button is pressed. Step 4: When you press the button with a snowflake symbol on it for once while the version number is being displayed during the service test, first the frz_eva sensor (red) will illuminate on the LED indicator and the temperature value of this sensor will appear on the seven segment display; and then, the frz_air sensor (orange) will illuminate on the LED indicator and the temperature value of this sensor will appear on the seven segment display. This cycle continues until the button is pressed. 57 January 11

58 F60265NE TRAINING DOCUMENT (with BDC-Electronic card) SERVICE TEST SERVICE TEST COMPRESSOR DRIVE STEP, SEVEN SEGMENT AND LED INDICATORCON TROL Step 5 During service test, when sensor temperatures appear on the display, pressing snow flake button once starts compressor drive step of service test and compressor operates during this step. In this step, seven segment and LED indicator is as shown below. Step 5 During service test, when sensor temperatures appear on the display, pressing snow flake button once starts compressor drive step of service test and compressor operates during this step. In this step, seven segment and LED indicator are as shown below. SERVICE TEST DEFROST HEATER DRIVE STEP, SEVEN SEGMENT AND LED INDICATORCONT ROL Step 6 During compressor drive step of the service test, pressing snow flake button once starts defrost heater drive step of service test and heater operates during this step. In this step, seven segment and LED indicator are as shown below. Step 6 During compressor drive step of the service test, pressing snow flake button once starts defrost heater drive step of service test and heater operates during this step. In this step, seven segment and LED indicator are as shown below. Step 7 During defrost heater drive step of the service test, when snow flake button is pressed once seven segment and LED indicator are as shown below. Step 7 During defrost heater drive step of the service test, when snow flake button is pressed once seven segment and LED indicator are as shown below. SENSOR TEMPERATURE S AND LED INDICATOR CONTROL 58 January 11

59 8.4. KARDELEN LED INDICATOR - Green Led lights continuously - Yellow Led lights in pot max position. - Red Led lights if there is a sensor error or high temperature alarm. - The following is the normal operation mode. 59 January 11

60 9. FAILURE CODES 9.1. Products with Arçelik New Appearance and Beko New Appearance Display Alarm indicator flashes on and off when High Temperature Alarm occurs. In sensor failures, both alarm indicator and error code flash in accordance with the following codes. Following failures will occur if the connections are open or short circuited. Alarm indicator and the error code will start blinking concurrently. Errors Error Code Freezer Air Sensor Error 24 Defrost Heater Error 20 Freezer Evaporator Sensor Error January 11

61 9.2. Products with Kardelen LED Indicator In error conditions, red light flashes BEKO ELECTRONIC LED INDICATOR (with BDC card) Error messages: Error messages that can appear on the FRZ display are indicated below: - E0 and flashing red light = FRZ sensor - E1 and flashing red light = Defrost sensor - E4 and flashing red light = Heater failure - Continuous red light = High Temperature Alarm If more than one error occur, these errors and FRZ actual value are indicated alternately with 1-second intervals. 61 January 11

62 10. ELECTRIC CIRCUIT / CONNECTION / E-CARD DIAGRAMS Electric Circuit Diagram Products with Arçelik New Appearance and Beko New Appearance Display 62 January 11

63 Products with LED Kardelen 63 January 11

64 BEKO ELECTRONIC LED INDICATOR (with BDC card) 64 January 11

65 10.2 PCB Diagram Alaska Control Card PCB TOP 65 January 11

66 Kardelen Control Card PCB TOP 66 January 11

67 BEKO ELECTRONIC LED INDICATOR (with BDC card) 67 January 11

68 9. EXPLODED DRAWINGS IMPORTANT!!: For the latest exploded drawings, please check manusoft; this list is for reference only. Exploded Drawing No(All Models Common): Body Gr: 902 Accessory: 901 Comp. 890 Door assembly: January 11

69 69 January 11

70 70 January 11

71 71 January 11

72 72 January 11