2220 SE Ninth Avenue 2113 Delta Waters Road Portland OR Medford OR

Transcription

1 Page: 117

2 Furnaces 97+% Gas Furnace Acclimate Series LXLP9C060B12MP11 * 97.5% MODULATING 60,000 BTU 1200 CFM MULTI-POSITION GAS FURNACE $3, LXLP9C080B12MP11 * 97.5% MODULATING 80,000 BTU 1200 CFM MULTI-POSITION GAS FURNACE $3, LXLP9C080C16MP11 * 97.7% MODULATING 80,000 BTU 1600 CFM MULTI-POSITION GAS FURNACE $3, LXLP9C100C16MP11 * 97.7% MODULATING 100,000 BTU 1600 CFM MULTI-POSITION GAS FURNACE $4, (WITH ECM MOTOR) LXLP9C100C20MP11 * 97.7% MODULATING 100,000 BTU 2000 CFM MULTI-POSITION GAS FURNACE $4, Luxaire LXLP9C 97+% MODULATING GAS-FIRED RESIDENTIAL MULTI-POSITION FURNACES Capacities: MBH INPUT Efficiency: AFUE Warranty Lifetime limited warranty on the heat exchanger. 10-year heat exchanger warranty on c ommercial applications. 10-year limited parts warranty. Luxaire LXLP9C 97+% MODULATING GAS-FIRED RESIDENTIAL MULTI-POSITION FURNACES (ECM Motor) The LXLP9C compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in up-flow or horizontal applications and may be converted for down-flow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category IV listed and may be vented either through side wall or roof applications using approved plastic combustion air and vent piping. Special Benefits Modulating heating operation includes: - Modulating gas valve, inducer and circulating blower - Modulating operation from 100% to 35% input in 100% increments with nearly constant temperature rise. Easily applied in up-flow, horizontal left or right, or down-flow installation with minimal conversion necessary. Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability. Movable duct connector flanges for application flexibility. Easy access to controls to connect power/control wiring. Built-in, high level self diagnostics with fault code display. Low unit amp requirement for easy replacement application. All models are convertible to use propane (LP) gas. Hi-tech tubular aluminized steel primary heat exchanger with stainless steel tube/aluminum fin secondary heat exchanger for outstanding efficiency. Fully supported blower assembly for easy access and removal of blower. Insulated blower compartment for thermal and acoustic performance. 1/4 turn knobs provided for easy independent door removal. ECM variable speed drive for cooling SEER enhancement, improved comfort with optional airflow delay profiles, and continuous fan options for IAQ performance. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Quiet inducer operation, burner, and blower operation. No knockouts to deal with, making installation easier. Compact, easy to install, ideal height 33" tall cabinet. 100% shut off main gas valve for extra safety. Solid removable bottom panel allows easy conversion. Inducer rotates for easy conversion of venting options. Internal condensate trap design (patent pending) provides condensate management options, easy visual operation check and is self priming to prevent nuisance problems. External air filters used for maximum flexibility in meeting customers IAQ needs. Airflow leakage less than 1% of nominal airflow for duct blaster conditions Page: 118

3 Furnaces 97+% Gas Furnace Acclimate Series Cabinet and Duct Dimensions Cabinet Dimensions (Inches) Nominal CFM (m 3 /min) Cabinet Size A B C Approximate Operating Weights LBS Model LXLP9C060B12MP B 17 1/2 16 3/8 13 1/4 122 LXLP9C080B12MP B 17 1/2 16 3/8 14 3/4 126 LXLP9C080C16MP C /8 16 1/2 136 LXLP9C100C16MP C /8 18 1/4 142 LXLP9C100C20MP C /8 18 1/4 145 Ratings & Physical / Electrical Data Input Output Blower Max. Outlet Air Temp Model MBH MBH AFUE F HP AMP Blower Size Max Over- Current Protect Total Unit Amps MIN Wire Size 75 ft one way LXLP9C060B12MP11 60/21 58/ / x LXLP9C080B12MP11 80/28 77/ / x LXLP9C080C16MP11 80/28 78/ / x LXLP9C100C16MP11 100/35 97/ / x LXLP9C100C20MP11 100/35 97/ x Model Air Temp. Rise Max F Air Temp. Rise Min F LXLP9C060B12MP LXLP9C080B12MP LXLP9C080C16MP LXLP9C100C16MP LXLP9C100C20MP Page: 119

4 Furnaces 97+% Gas Furnace Acclimate Series LXLM9M060B12MP11 LXLM9M080C16MP11 LXLM9M100C20MP11 * 97% MODULATING 60,000 BTU 1200 CFM MULTI-POSITION GAS FURNACE (WITH PSC MOTOR) * 97% MODULATING 80,000 BTU 1600 CFM MULTI-POSITION GAS FURNACE (WITH PSC MOTOR) * 97% MODULATING 100,000 BTU 2000 CFM MULTI-POSITION GAS FURNACE (WITH PSC MOTOR) Luxaire LXLM9M 97% MODULATING GAS-FIRED RESIDENTIAL MULTI-POSITION FURNACES Capacities: MBH INPUT Efficiency: 97.0 AFUE Warranty Lifetime limited warranty on the heat exchanger. 10-year heat exchanger warranty on c ommercial applications. 10-year limited parts warranty. Luxaire LXLM9M 97% MODULATING GAS-FIRED RESIDENTIAL MULTI-POSITION FURNACES (PSC Motor) The LXLM9M compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in up-flow or horizontal applications and may be converted for down-flow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category IV listed and may be vented either through side wall or roof applications using approved plastic combustion air and vent piping. Special Benefits Easily applied in up-flow, horizontal left or right, or down-flow Timed on, adjustable off blower capability for maximum comfort. installation with minimal conversion necessary. Compact, easy to install, ideal height 33" tall cabinet. Blower door safety switch. Blower-off delay for cooling SEER improvement. Solid removable bottom panel allows easy conversion. Easy access to controls to connect power/control wiring. Airflow leakage less than 1% of nominal airflow at Duct blaster conditions. Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation. Airflow leakage less than 1% of total airflow at duct-blaster conditions. Low unit amp requirement for easy replacement application. No knockouts to deal with, making installation easier. Single wire twinning or staging feature available. Movable duct connector flanges for application flexibility. All models are convertible to use propane (LP) gas. Quiet inducer operation. Electronic Hot Surface Ignition saves fuel cost with increased Inducer rotates for easy conversion of venting options. dependability and reliability. 100% shut off main gas valve for extra safety. Fully supported blower assembly for easy access and removal of blower. 4 speed, direct drive PSC motor. External air filters used for maximum flexibility in meeting customers IAQ needs. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Protection included from air intake, exhaust vent, or condensate blockage. Internal condensate trap design (patent pending) provides condensate management options, easy visual operation, and is self-priming to prevent nuisance problems. Secondary heat exchanger made of corrosion resistant stainless steel materials. Venting applications - may be installed as a common vent with other gas-fired appliances or use a lined masonry chimney. No Special Vent termination required. Hi-tech tubular aluminized steel primary heat exchanger. 1/4 turn knobs provided for easy door removal. $2, $2, $3, Page: 120

5 Furnaces 97+% Gas Furnace Acclimate Series Cabinet and Duct Dimensions Cabinet Dimensions (Inches) Model Nominal CFM (m 3 /min) Cabinet Size A B C Approximate Operating Weights LBS LXLM9M060B12MP B 17 1/2 16 3/8 13 1/4 122 LXLM9M080C16MP B /8 16 1/2 136 LXLM9M100C20MP C /8 18 1/4 145 Ratings & Physical / Electrical Data Input Output Blower MIN Wire Max. Outlet Air Max Over- Total Size (AWG) Temp Blower Current 75 ft one Model MBH MBH AFUE F HP AMP Size Protect Amps way LXLM9M060B12MP11 60/21 58/ / x LXLM9M080C16MP11 80/28 78/ / x LXLM9M100C20MP11 100/35 97/ x Model Air Temp. Rise Max F Air Temp. Rise Min F LXLM9M060B12MP LXLM9M080C16MP LXLM9M100C20MP Page: 121

6 Furnaces 95% Gas Furnace Climasure Series LXTG9S040A08MP11 * 95% 40,000 BTU 800 CFM MULTI-POSITION GAS FURNACE $1, LXTG9S060A10MP11 * 95% 60,000 BTU 1000 CFM MULTI-POSITION GAS FURNACE $1, LXTG9S060B12MP11 * 95% 60,000 BTU 1200 CFM MULTI-POSITION GAS FURNACE $1, LXTG9S080B12MP11 * 95% 80,000 BTU 1200 CFM MULTI-POSITION GAS FURNACE $1, LXTG9S080C16MP11 * 95% 80,000 BTU 1600 CFM MULTI-POSITION GAS FURNACE $1, LXTG9S080C22MP11 * 95% 80,000 BTU 2200 CFM MULTI-POSITION GAS FURNACE $1, LXTG9S100C16MP11 * 95% 100,000 BTU 1600 CFM MULTI-POSITION GAS FURNACE $2, LXTG9S100C20MP11 * 95% 100,000 BTU 2000 CFM MULTI-POSITION GAS FURNACE $2, LXTG9S120D16MP11 * 95% 120,000 BTU 1600 CFM MULTI-POSITION GAS FURNACE $2, LXTG9S120D20MP11 * 95% 120,000 BTU 2000 CFM MULTI-POSITION GAS FURNACE $2, LXTG9S130D20MP11 * 95% 130,000 BTU 2000 CFM MULTI-POSITION GAS FURNACE $2, Luxaire LXTG9S Climasure 95.5% SINGLE STAGE GAS-FIRED RESIDENTIAL MULTI-POSITION FURNACES Capacities: MBH INPUT Efficiency: 95.5 AFUE Warranty Lifetime limited warranty on the heat exchanger. 10-year heat exchanger warranty on commercial applications. 10-year limited parts warranty. Luxaire LXTG9S Climasure 95.5% SINGLE STAGE GAS-FIRED RESIDENTIAL MULTI-POSITION FURNACES The LXTG9S compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in up-flow or horizontal applications and may be converted for down-flow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category IV listed and may be vented either through side wall or roof applications using approved plastic combustion air and vent piping. Special Benefits Easily applied in up-flow, horizontal left or right, or down-flow Timed on, adjustable off blower capability for maximum installation with minimal conversion necessary. comfort. Compact, easy to install, ideal height 33" tall cabinet. Blower door safety switch. Blower-off delay for cooling SEER improvement. Solid removable bottom panel allows easy conversion. Easy access to controls to connect power/control wiring. Airflow leakage less than 1% of nominal airflow at Duct blaster conditions. Built-in, high level self diagnostics with fault code displays Airflow leakage less than 1% of total airflow at duct-blaster standard on integrated control module for reliable operation. conditions. Low unit amp requirement for easy replacement application. No knockouts to deal with, making installation easier. Single wire twinning or staging feature available. Movable duct connector flanges for application flexibility. All models are convertible to use propane (LP) gas. Quiet inducer operation. Electronic Hot Surface Ignition saves fuel cost with increased Inducer rotates for easy conversion of venting options. dependability and reliability. 100% shut off main gas valve for extra safety. Fully supported blower assembly for easy access and removal of blower. 4 speed, direct drive PSC motor. External air filters used for maximum flexibility in meeting customers IAQ needs. 24V, 40 VA control transformer and blower relay supplied for Protection included from air intake, exhaust vent, or condensate add-on cooling. Internal condensate trap design (patent pending) provides condensate management options, easy visual operation, and is self-priming to prevent nuisance problems. blockage.. Venting applications - may be installed as a common vent with other gas-fired appliances or use a lined masonry chimney. Secondary heat exchanger made of corrosion resistant No Special Vent termination required. stainless steel materials. Hi-tech tubular aluminized steel primary heat exchanger. 1/4 turn knobs provided for easy door removal Page: 122

7 Furnaces 95% Gas Furnace Climasure Series Cabinet and Duct Dimensions Cabinet Dimensions (Inches) Model Nominal CFM (m 3 /min) Cabinet Size A B C Approximate Operating Weights LBS LXTG9S040A08MP A 14 1/2 13 3/8 11 3/4 113 LXTG9S060A10MP A 14 1/2 13 3/8 11 3/4 118 LXTG9S060B12MP B 17 1/2 16 3/8 13 1/4 122 LXTG9S080B12MP B 17 1/2 16 3/8 14 3/4 126 LXTG9S080C16MP C /8 16 1/2 136 LXTG9S080C22MP C /8 16 1/2 139 LXTG9S100C16MP C /8 18 1/4 142 LXTG9S100C20MP C /8 18 1/4 145 LXTG9S120D16MP D 24 1/2 23 3/8 21 3/4 153 LXTG9S120D20MP D 24 1/2 23 3/8 21 3/4 156 LXTG9S130D20MP D 24 1/2 23 3/8 No Hole 160 Ratings & Physical / Electrical Data Input Output Blower MI N Wire Max. Air Temp. Outlet Air Max Over- Total Size (AWG) Model MBH MBH AFUE Rise F Temp F HP AMP Blower Size Current Protect Unit 75 ft one way LXTG9S040A08MP / x LXTG9S060A10MP / x LXTG9S060B12MP / x LXTG9S080B12MP / x LXTG9S080C16MP / x LXTG9S080C22MP x LXTG9S100C16MP / x LXTG9S100C20MP x LXTG9S120D16MP / x LXTG9S120D20MP x LXTG9S130D20MP x Page: 123

8 Furnaces 80% Gas Furnaces Climasure Series LXTG8S040A08MP11 * 80% 40,000 BTU 800 CFM MULTI-POSITION GAS FURNACE $ LXTG8S060A12MP11 * 80% 60,000 BTU 1200 CFM MULTI-POSITION GAS FURNACE $1, LXTG8S080B12MP11 * 80% 80,000 BTU 1200 CFM MULTI-POSITION GAS FURNACE $1, LXTG8S080C16MP11 * 80% 80,000 BTU 1600 CFM MULTI-POSITION GAS FURNACE $1, LXTG8S100C20MP11 * 80% 100,000 BTU 2000 CFM MULTI-POSITION GAS FURNACE $1, Luxaire LXTG8S Climasure GAS-FIRED RESIDENTIAL SINGLE STAGE MULTI-POSITION FURNACES Capacities: MBH INPUT Efficiency: 80 AFUE Warranty 20-year limited warranty on the heat exchanger. 10-year heat exchanger warranty on commercial applications. 10-year limited parts warranty. Luxaire LXTG8S Climasure GAS-FIRED RESIDENTIAL SINGLE STAGE MULTI-POSITION FURNACES The LXTG8S compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in up-flow or horizontal applications and may be converted for down-flow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code. Special Benefits Easily applied in up-flow, horizontal left or right, or down-flow installation with minimal conversion necessary. Timed on, adjustable off blower capability for maximum comfort. Compact, easy to install, ideal height 33" tall cabinet. Blower door safety switch. Blower-off delay for cooling SEER improvement. Solid removable bottom panel allows easy conversion. Easy access to controls to connect power/control wiring. Low NOx models have been designed to meet specific code requirements. Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation. Airflow leakage less than 1% of total airflow at duct-blaster conditions. Low unit amp requirement for easy replacement application. No knockouts to deal with, making installation easier. Single wire twinning or staging feature available. Movable duct connector flanges for application flexibility. All models are convertible to use propane (LP) gas. Quiet inducer operation. Electronic Hot Surface Ignition saves fuel cost with increased Inducer rotates for easy conversion of venting options. dependability and reliability. 100% shut off main gas valve for extra safety. Fully supported blower assembly for easy access and removal of blower. 4 speed, direct drive PSC motor. External air filters used for maximum flexibility in meeting customers IAQ needs. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Venting applications - may be installed as a common vent with other gas-fired appliances or use a lined masonry chimney. Hi-tech tubular aluminized steel primary heat exchanger. 1/4 turn knobs provided for easy door removal Page: 124

9 Furnaces 80% Gas Furnaces Climasure Series Cabinet and Duct Dimensions Cabinet Size Cabinet Dimensions (Inches) Model Nominal CFM (m 3 /min) A B C Approximate Operating Weights LBS LXTG8S040A08MP A 14 1/2 13 3/ LXTG8S060A12MP A 14 1/2 13 3/ LXTG8S080B12MP B 17 1/2 16 3/ LXTG8S080C16MP C / LXTG8S100C20MP C / Ratings and Physical / Electrical Data Ma x. Blower Input Output Air Temp. Outlet Air Rise Temp Model MBH MBH AFUE F F HP AMP Blower Size Max Over- Current Protect Total Unit Amps MIN Wire Size 75 ft one way LXTG8S040A08MP / x LXTG8S060A12MP / x LXTG8S080B12MP / x LXTG8S080C16MP / x LXTG8S100C20MP x Page: 125

10 Furnaces 80% Gas Furnaces Acclimate Series LXLP8C060A12MP11 LXLP8C080B12MP11 LXLP8C080C16MP11 LXLP8C100C20MP11 * 80% MODULATING 60,000 BTU 1200 CFM MULTI-POSITION GAS FURNACE (WITH ECM MOTOR) * 80% MODULATING 80,000 BTU 1200 CFM MULTI-POSITION GAS FURNACE (WITH ECM MOTOR) * 80% MODULATING 80,000 BTU 1600 CFM MULTI-POSITION GAS FURNACE (WITH ECM MOTOR) * 80% MODULATING 100,000 BTU 2000 CFM MULTI-POSITION GAS FURNACE (WITH ECM MOTOR) Luxaire LXLP8C Acclimate 80% MODULATING GAS-FIRED RESIDENTIAL MULTI-POSITION GAS FURNACES Capacities: MBH INPUT Efficiency: 80 AFUE Warranty Lifetime limited warranty on both heat exchangers to the original purchaser; a 20-year limited warranty from original installation date to subsequent purchaser. 10-year warranty on the heat exchanger in commercial applications. 10-year limited parts warranty. Acclimate LXLP8C 80% MODULATING (ECM MOTOR) GAS-FIRED RESIDENTIAL MULTI-POSITION GAS FURNACES The LXLP8C compact units employ induc ed combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in up-flow or horizontal applications and may be converted for down-flow applications. These furnac es are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. Thes e units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code. Special Benefits Modulating heating operation includes: - Modulating gas valve, inducer and circulating blower - Modulating operation from 100% input to 50% input in 1% increments Easily applied in up-flow, horizontal left or right, or down-flow installation with minimal conversion necessary. Compact, easy to install, ideal height 33" tall cabinet. ECM variable speed motor for cooling SEER enhancement, blower delay options for comfort, and continuous fan options for IAQ performance. Easy access to controls to connect power/control wiring. Built-in, high level self diagnostics with fault code display. Low unit amp requirement for easy replacement application. All models are convertible to use propane (LP) gas. Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability. 100% shut off main gas valve for extra safety. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Hi-tech tubular aluminized steel primary heat exchanger. Blower door safety switch. Solid removable bottom panel allows easy conversion. Low NOx models have been designed to meet specific code requirements. Airflow leakage less than 1% of nominal airflow for duct blaster conditions. No knockouts to deal with, making installation easier. Movable duct connector flanges for application flexibility. Quiet inducer, burner and blower operation. Inducer rotates for easy conversion of venting options. Fully supported blower assembly for easy access and removal of blower. External air filters used for maximum flexibility in meeting customers IAQ needs. Venting applications - may be installed as a common vent with other gas-fired appliances. Insulated blower compartment for thermal and acoustic performance. 1/4 turn knobs provided for easy door removal. $2, $2, $2, $3, Page: 126

11 Furnaces 80% Gas Furnaces Acclimate Series Cabinet and Duct Dimensions Nominal Cabinet Cabinet Dimensions (inches) CFM Model (m 3 /min) Size A B C Approx Operating Weight LBS LXLP8C060A12MP A 14 1/2 13 1/ LXLP8C080B12MP B 17 1/2 16 1/ LXLP8C080C16MP C / LXLP8C100C20MP C / Ratings and Physical / Electrical Data Input Max/Min MBH Output Max/Min MBH AFUE Nominal Airflow CFM Total Unit AMPS Air Temp Max Input. F Air Temp Min Input. F LXLP8C060A12MP11 60/30 47/ LXLP8C080B12MP11 80/40 62/ LXLP8C080C16MP11 80/40 62/ LXLP8C100C20MP11 100/50 78/ Max. Outlet Air Temp F Blower HP Blower AMPS Blower Wheel size Max Over Current Protect Min. wire Size 75 ft one way LXLP8C060A12MP / x LXLP8C080B12MP / x LXLP8C080C16MP / x LXLP8C100C20MP x Page: 127

12 Furnaces Air Handlers Climasure - Modular LXMA08BN21 * 2.0 TON 230V MULTI-POSITION MODULAR AIR HANDLER (WITH PSC MOTOR) $ LXMA12BN21 * 3.0 TON 230V MULTI-POSITION MODULAR AIR HANDLER (WITH PSC MOTOR) $ LXMA16CN21 * 4.0 TON 230V MULTI-POSITION MODULAR AIR HANDLER (WITH PSC MOTOR) $ LXMA20DN21 * 5.0 TON 230V MULTI-POSITION MODULAR AIR HANDLER (WITH PSC MOTOR) $ Warranty 10-year limited parts warranty. Luxaire LXMA Climasure MODULAR AIR HANDLERS FOR USE WITH SPLIT-SYSTEM COOLING & HEAT PUMPS Climasure LXMA MODULAR AIR HANDLERS FOR USE WITH SPLIT-SYSTEM COOLING & HEAT PUMPS The LXMA is a modular system that allows the flexibility to handle any application. These versatile coils and blowers may be used for upflow, down-flow, or horizontal left or right applications. They may be combined to function as a cooling only unit or with a heat pump including electric heat for 1 and 3 phase applications. The blower and electric heater could be used as standalone electric furnaces. Special Benefits BLOWERS - Models to match any air flow or voltage requirement. The compact size allows easy installation. Blowers are sized to deliver design air quantity both efficiently and quietly. The direct-drive, multi-speed blower motors provide a selection of air quantities to match any application. All models include a one-minute blower off delay as standard to enhance system efficiency ratings. The durable, pre-painted steel protects the unit against rust and corrosion. All models have 1 inch foil face fiber glass insulation, providing a thermal insulation value of R COILS - Staggered rows of rifled copper tubes are mechanically expanded into enhanced surface aluminum fins to provide high heat transfer and long-lasting quality. The MC multi-position coils may be used for up-flow, down-flow, and horizontal left or right applications. Coil cabinets are insulated with 3/4" foil face insulation to prevent sweating. ELECTRIC HEATERS - Both single and three phase electric heater models are available to match any requirement. All heaters include nickel-chromium elements with a 5-year limited warranty on 1 Ø heating elements and 1 year limited warranty on 3 Ø heating elements. Sequential operation is provided to control heaters in all models. Circuit breakers are used in 208/230 volt, single-phase heaters of 15 KW and larger. Models equipped with circuit breakers may be altered in the field to use multi-source power supply. Over-temperature limit switches provide protection from airflow loss with fusible link backup protection. NOTE: No heat kits are available for 115 Volt models. ACCESSORIES - A full line of matching accessories available for use with the blower and coils to allow any type application. LIMITATIONS - These units must be wired and installed in accordance with all national and local safety codes Page: 128

13 Furnaces Air Handlers Climasure - Modular NOTE: Power wiring may be brought into the unit through one of the knockouts in either the top or the left side panel. Multiple knockouts are provided to accommodate all of the electric heat and transformer accessories that are available. Use the knockouts that provide the best wire routing for the accessory being used. Model LXMA08BN Dimensions (inches) Wiring Knockouts 1 A B C D E J K Height Width Total Height Power Control 16 1/ /32 LXMA12BN to 57 Depending 16 1/ /32 LXMA16BN on combination /32 LXMA20BN / /32 1 Parenthesis indicate conduit size. 2 May be either , 208/ or /8 (1/2 ), 1 3/8 (1 ), 1 23/32 (1 1/4 ), 1 31/32" (1 1/2") 7/8 (1/2 ) Page: 129

14 Furnaces Air Handlers Climasure - Modular LXMV12BN21 * 3.0 TON 230V MULTI-POSITION MODULAR AIR HANDLER (WITH ECM MOTOR) $1, LXMV16CN21 * 4.0 TON 230V MULTI-POSITION MODULAR AIR HANDLER (WITH ECM MOTOR) $1, LXMV20DN21 * 5.0 TON 230V MULTI-POSITION MODULAR AIR HANDLER (WITH ECM MOTOR) $1, Luxaire LXMV Climasure MODULAR VARIABLE SPEED AIR HANDLERS FOR USE WITH SPLIT-SYSTEM COOLING & HEAT PUMPS Warranty 10-year limited parts warranty. Climasure LXMV MODULAR VARIABLE SPEED AIR HANDLERS FOR USE WITH SPLIT-SYSTEM COOLING & HEAT PUMPS The LXMV is a modular system that allows the flexibility to handle any application. These versatile coils and blowers may be used for upflow, down-flow, or horizontal left or right applications. They may be combined to function as a cooling only unit or with a heat pump including electric heat for 1 and 3 phase applications. The blower and electric heater could be used as standalone electric furnaces. Special Benefits BLOWERS - Models to match any air flow or voltage requirement. The compact size allows easy installation. Blowers are sized to deliver design air quantity both efficiently and quietly. The direct-drive, multi-speed blower motors provide a selection of air quantities to match any application. All models include a one-minute blower off delay as standard to enhance system efficiency ratings. The durable, pre-painted steel protects the unit against rust and corrosion. All models have 1 inch foil face fiber glass insulation, providing a thermal insulation value of R COILS - Staggered rows of rifled copper tubes are mechanically expanded into enhanced surface aluminum fins to provide high heat transfer and long-lasting quality. The MC multi-position coils may be used for up-flow, down-flow, and horizontal left or right applications. Coil cabinets are insulated with 3/4" foil face insulation to prevent sweating. ELECTRIC HEATERS - Both single and three phase electric heater models are available to match any requirement. All heaters include nickel-chromium elements with a 5-year limited warranty on 1 Ø heating elements and 1 year limited warranty on 3 Ø heating elements. Sequential operation is provided to control heaters in all models. Circuit breakers are used in 208/230 volt, single-phase heaters of 15 KW and larger. Models equipped with circuit breakers may be altered in the field to use multi-source power supply. Over-temperature limit switches provide protection from airflow loss with fusible link backup protection. Thermal Expansion Valves - Available with R-22 or R-410A factory installed TXV s. Air Handlers maybe ordered as Flexcoil unit without a factory installed metering device. Flex-coil models allow for field installed R-22 or R-410A TXV s for added flexibility to meet refrigerant system choice. ACCESSORIES - A full line of matching accessories available for use with the blower and coils to allow any type application. LIMITATIONS - These units must be wired and installed in accordance with all national and local safety codes Page: 130

15 Furnaces Air Handlers Climasure - Modular NOTE: Power wiring may be brought into the unit through one of the knockouts in either the top or the left side panel. Multiple knockouts are provided to accommodate all of the electric heat and transformer accessories that are available. Use the knockouts that provide the best wire routing for the accessory being used. Dimensions (inches) Wiring Knockouts 1 Model A B C D E J K Height Width Total Height Power Control LXMV12BN / /32 7/8 (1/2 ), 47 to 57 Depending LXMV16CN /32 1 3/8 (1 ), on combination. 1 23/32 (1 1/4 ), LXMA20DN / /32 7/8 (1/2 ) 1 Parenthesis indicate conduit size Page: 131

16 Furnaces Air Handlers Acclimate - Variable Speed LXAVL48D3XH21 * 4.0 TON MULTI-POSITION VARIABLE-SPEED AIR HANDLER (ADD TXV KIT) $2, LXAVL60D3XH21 * 5.0 TON MULTI-POSITION VARIABLE-SPEED AIR HANDLER (ADD TXV KIT) $2, Luxaire LXAVL ACCLIMATE SINGLE PIECE VARIABLE SPEED AIR HANDLERS FOR USE WITH SPLIT-SYSTEM COOLING & HEAT PUMPS Warranty 10-year limited parts warranty. Acclimate LXAVL SINGLE PIECE VARIABLE SPEED AIR HANDLERS FOR USE WITH SPLIT-SYSTEM COOLING & HEAT PUMPS The LXAVL Acclimate Air Handler line offers the ultimate in comfort, sound and application flexibility. The Acclimate models utilize a whisper quiet variable speed motor that provides humidity control and the lowest operating cost in the industry. The AVL air handler is shipped ready to be installed in all positions, up-flow, down-flow, horizontal left or right, with minor adjustments. The SVL 48 & 60 models are upflow only models designed into a shorter cabinet, for those special applications where reduced height is required. No special kits are required to install this deluxe product in any position. All JCI Unitary Products air handlers and coils use a TXV to provide our customers with the optimum performance and refrigerant control required for 13 + Seer systems. Air handlers can be ordered with either a R-22 or R-410A TXV factory installed. Air handlers are also available with Flex-coils without a factory installed metering device, where for added flexibility, a R- 22 or R-410A TXV can be field installed to meet your refrigerant choice. Special Benefits Thermal Expansion Valve - Provides the ultimate refrigerant control required for today s high efficient product. The UPG bolt on TXV provides easy installation to convert the air handler to the required refrigerant, which is a true bolt-on design that does not require brazing to replace or install. Micro Blue TM Coated Fins - All air handler coils are treated with the Micro Blue TM hydrophilic coating to enhance the removal of condensate during the refrigeration cycle and reduce the possibility of water blow-off. The Micro Blue TM coating also reduces the growth of germ causing microbes for a healthier home environment. Insulated Cabinet - All air handler cabinets are thermally insulated with 1 foil faced insulation (R-4.2) to prevent sweating. For applications in extreme humidity conditions an optional, field installed, external insulating wrap kit is also available. Factory - Sealed to achieve 2% or less leakage rate with or without field installed filter at 1.0 water gauge external static pressure. Durable Finish Inside and Out - Air handler casings are made of pre-painted galvanized steel which provides a better paint to steel bond that resists corrosion and rust creep. All internal coil sheet metal parts are made of G90 galvanized. New 4 HK Heat Kit - Installation friendly, easy service, more robust, unique to new design. ECM Variable Speed Motor - Designed for efficient, quiet operation with added indoor comfort control. With the use of a humidistat, the motor will monitor the humidity in the home and automatically keep the desired humidity level in both winter and summer seasons. The ECM motor utilizes only 24% of the energy used by standard blower motors to reduce your overall heating and cooling costs. GeoTrak Comfort Settings - Installers can set an operating cycle for the ECM motor that works best in a particular climate. Homeowners benefit from an operating cycle that maximizes their indoor comfort level regardless of whether they live in a dry, temperate, or humid climate Page: 132

17 Furnaces Air Handlers Acclimate - Variable Speed Model Refrigerant Connections A B C D E F J K Line Size Height Width Depth Power Control Liquid Vapor AVL48D3XH / / /32 7/8 (1/2 ) 3/8 7/8 7/8 (1/2 ) 24.5 (w/o cladding) 1 3/8 (1 ) AVL60D3XH (with cladding) 22-1/ / /32 7/8 (1/2 ) 3/8 7/8 1 23/32 (1 1/4 ) 1 Actual size (Conduit size). Thermal expansion device indicators: 3X indicates unit is a Flex Coil model with a field installed R-22 or R-410A TXV. Letter indicates TXV size as required, see outdoor unit technical information for proper matches and requirements Page: 133

18 Air Conditioners 15+ SEER Acclimate Series LXAL5B024F1 * 2.0 TON 15 SEER 2 STAGE AIR CONDITIONER R410A $3, LXAL5B036F1 * 3.0 TON 15 SEER 2 STAGE AIR CONDITIONER R410A $4, LXAL5B048F1 * 4.0 TON 15 SEER 2 STAGE AIR CONDITIONER R410A $4, Luxaire LXAL5B ACCLIMATE 15 SEER Split System Air Conditioner using R-410A Capacities: 2-4 Tons Efficiency: 15 SEER Warranty 10-year limited parts warranty. 10-year limited compressor warranty. Premium System Warranty - Limited lifetime compressor when matched with an approved Luxaire Acclimate furnace or UPG air handler and coil. Acclimate LXAL5B Split System Air Conditioner - 15 SEER R-410A 1 Phase The LXAL5B 15 SEER Series unit is the outdoor part of a versatile climate system. It is designed with a matching indoor coil component from Johnson Controls Unitary Products. Available for typical applications this climate system is supported with accessories and documents to serve specific functions. Special Benefits Superior Coil Protection A Stamped coil guard completely protects coil from debris and other large damaging material while a polymer mesh further protects the coil against smaller particles. Isolated Compressor Compartment A molded composite bulkhead isolates the compressor from the rest of the unit reducing sound and vibration. Protected Compressors Each compressor is protected against abnormal pressures by an internal pressure relief valve and factory installed high and low pressure controls. Additional protection against moisture and debris is provided by factory installed liquid line filter driers. Environmentally Friendly Refrigerant Next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion. Durable Finish Automotive quality finish provides the ultimate protection from harmful U.V. rays and rust creep ensuring long-lasting high quality appearance. A powder-paint topcoat is applied over a baked-on primer, using a galvanized, zinc coated steel base material. The result is a finish that has been proven in testing to provide 33% greater durability than conventional powder-coat finishes. Lower Installed Cost Designed to provide enhanced instability by featuring a slide-down control compartment and angled service valves to reduce overall installation time and cost. Low Operating Sound Levels A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper quiet operation by allowing airflow to flow smoothly and efficiently across the fan tips. Filter-Drier A factory installed, solid core liquid line filter-drier, filters harmful debris and moisture from the system. Easy Service Access A full end, full service, access panel with handle makes for easy entry to internal components. Composite Base - Strong and durable composite base pan resists rust and corrosion while it helps reduce vibrations and noise. Silent drive system - Features combination of swept-wing fan, composite base pan, isolated compressor compartment and two-stage compressor to reduce overall sound to a mere whisper. Low RPM fan motor - Helps to reduce airflow noise. Agency Listed - U.L. and C.U.L. listed - approved for outdoor application. The unit is certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/ Page: 134

19 Air Conditioners 15+ SEER Acclimate Series Model LXAL5B024 LXAL5B036 LXAL5B048 F1 F1 F1 Unit Supply Voltage V, 60Hz, 1 Phase Normal Voltage Range to 252 Minimum Circuit Ampacity Max. Overcurrent Device Amps Min. Overcurrent Device Amps Compressor Type Scroll Scroll Scroll Compressor Amps Rated Load Locked Rotor Crankcase Heater No No No Fan Motor Amps Rated Load Fan Diameter Inches Rated HP 1/15 1/4 1/4 Fan Motor Nominal RPM Nominal CFM 2,000 3,450 3,250 Face Area Sq Ft. Coil Rows Deep Fins / Inch Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 Vapor Line Set OD (Field Installed) 3/4 3/4 7/8 Unit Charge (Lbs. - Oz.) Charge Per Foot Oz Operating Weight Lbs Rated in accordance with ARI Standard 110, utilization range A. 2 Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection. 3 Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection. 4 The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value. All dimensions are in inches. They are subject to change without notice. Certified dimensions will be provided upon request. Refrigerant Connection Service Dimensions (Inches) Valve Size Model A B C Liquid Vapor LXAL5B024F1 33 1/ /8" 3/4" LXAL5B036F1 33 1/ /8" 3/4" LXAL5B048F1 33 1/ /8" 7/8" * Expander fitting required for 1-1/8 line set Page: 135

20 Air Conditioners 13+ SEER Climasure Series LXTCGD18S41S1H * 1.5 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $1, LXTCGD24S41S1H * 2.0 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $1, LXTCGD30S41S1H * 2.5 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $1, LXTCGD36S41S1H * 3.0 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $2, LXTCGD42S41S1H * 3.5 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $2, LXTCGD48S41S1H * 4.0 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $2, LXTCGD60S41S1 * 5.0 TON 13 SEER AIR CONDITIONER R410A (HARDSTART KIT NOT REQUIRED) $2, Luxaire LXTCGD Climasure Air Conditioner using R-410A Capacities: 1.5 Thru 5.0 Tons Efficiency: 13 SEER Warranty 10-year limited parts warranty. 10-year limited compressor warranty. Climasure LXTCGD Split System Air Conditioner - 13 SEER R-410A 1 Phase The LXTCGD 13 SEER Series condensing unit is the outdoor part of a versatile system of air conditioning. It is designed to be custom matched with one of UPG s complete line of evaporator sections, with each serving a specific function. Matching Air Handlers are available for up-flow, down-flow, or horizontal applications to provide a complete system. Electric Heaters are available, if required. Add-on coils are available for use with up-flow, downflow, or horizontal furnaces and air handlers. Special Benefits QUALITY CONDENSER COILS - The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for increased efficiency and corrosion protection. PROTECTED COMPRESSOR - The compressor is internally protected against high pressure, temperature, and externally by a factory installed high pressure switch. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor. DURABLE FINISH - The cabinet is made of pre-painted steel. The pre-treated galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted-textured finish insure less fading when exposed to sunlight. LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof. TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications. LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. LOW MAINTENANCE - Long life permanently lubricated motor-bearings need no annual servicing. EASY SERVICE ACCESS - Fully exposed refrigerant connections, and a single panel covering the electrical controls make for easy servicing of the unit. SECURED SERVICE VALVES - Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging. U.L. and C.U.L. listed - approved for outdoor application. Agency Listed - U.L. and C.U.L. listed - approved for outdoor application. The unit is certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/ Page: 136

21 Air Conditioners 13+ SEER Climasure Series Model LXTCGD18 LXTCGD24 LXTCGD30 LXTCGD36 LXTCGD42 LXTCGD48 LXTCGD60 S41S1H S41S1H S41S1H S41S1H S41S1H S41S1H S41S1 Unit Supply Voltage V, 60Hz, 1 Phase Normal Voltage Range to 252 Minimum Circuit Ampacity Max. Overcurrent Device Amps Min. Overcurrent Device Amps Compressor Type Rotary Recip Recip Recip Recip Recip Scroll Compressor Amps Rated Load Locked Rotor Crankcase Heater No No No No No No No Fan Motor Amps Rated Load Fan Diameter Inches Rated HP 1/12 1/8 1/4 1/4 1/4 1/4 1/4 Fan Motor Nominal RPM Nominal CFM Face Area Sq. Ft Coil Rows Deep Fins / Inch Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line Set OD (Field Installed) 5/8 3/4 3/4 3/4 7/8 7/8 7/8 Unit Charge (Lbs. - Oz.) Charge Per Foot, Oz Operating Weight Lbs Models with H on the end of the model number have a factory installed start kits. 1 Rated in accordance with ARI Standard 110, utilization range A. 2. Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection. 3. Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection. 4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value Page: 137

22 Air Conditioners 13+ SEER LX Series - High Efficiency LXLCJD18S41S1H * 1.5 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $1, LXLCJD24S41S1H * 2.0 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $2, LXLCJD30S41S1H * 2.5 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $2, LXLCJD36S41S1H * 3.0 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $2, LXLCJD42S41S1H * 3.5 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $2, LXLCJD48S41S1H * 4.0 TON 13 SEER AIR CONDITIONER R410A W/HARDSTART KIT $3, LXLCJD60S41S1 * 5.0 TON 13 SEER AIR CONDITIONER R410A (HARDSTART KIT NOT REQUIRED) $3, Luxaire LXLCJD LX Series Air Conditioner using R-410A Capacities: 1.5 Thru 5.0 Tons Efficiency: 13 SEER Warranty 10-year limited parts warranty. 10-year limited compressor warranty. LX Series LXLCJD Split System Air Conditioner - 13 SEER R-410A 1 Phase The LXLCJD 13 SEER Series condensing unit is the outdoor part of a versatile system of air conditioning. It is designed to be custom matched with one of UPG s complete line of evaporator sections, with each serving a specific function. Matching Air Handlers are available for up-flow, down-flow, or horizontal applications to provide a complete system. Electric Heaters are available, if required. Add-on coils are available for use with up-flow, downflow, or horizontal furnaces and air handlers. Special Benefits QUALITY CONDENSER COILS - The coil is constructed of aluminum microchannel tubing and enhanced aluminum fins for increased efficiency and corrosion protection. PROTECTED COMPRESSOR - The compressor is internally protected against high pressure, temperature, and externally by a factory installed high pressure switch. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor. DURABLE FINISH - The cabinet is made of pre-painted steel. The pre-treated galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted-textured finish insure less fading when exposed to sunlight. LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof. TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications. LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. LOW MAINTENANCE - Long life permanently lubricated motor-bearings need no annual servicing. EASY SERVICE ACCESS - Fully exposed refrigerant connections, and a single panel covering the electrical controls make for easy servicing of the unit. SECURED SERVICE VALVES - Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging. U.L. and C.U.L. listed - approved for outdoor application. Agency List ed - U.L. and C.U.L. listed - approved for outdoor application. The unit is certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/ Page: 138

23 Air Conditioners 13+ SEER LX Series - High Efficiency Model LXLCJD18 LXLCJD24 LXLCJD30 LXLCJD36 LXLCJD42 LXLCJD48 LXLCJD60 S41S1H S41S1H S41S1H S41S1H S41S1H S41S1H S41S1 Unit Supply Voltage V, 60Hz, 1 Phase Normal Voltage Range to 252 Minimum Circuit Ampacity Max. Overcurrent Device Amps Min. Overcurrent Device Amps Compressor Type Rotary Recip Recip Recip Recip Recip Scroll Compressor Amps Rated Load Locked Rotor Crankcase Heater No No No No No No No Fan Motor Amps Rated Load Fan Diameter Inches Rated HP 1/12 1/8 1/4 1/4 1/4 1/4 1/4 Fan Motor Nominal RPM Nominal CFM Face Area Sq. Ft Coil Rows Deep Fins / Inch Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line Set OD (Field Installed) 5/8 3/4 3/4 3/4 7/8 7/8 7/8 Unit Charge (Lbs. - Oz.) Charge Per Foot Oz Operating Weight Lbs Models with H on the end of the model number have a factory installed start kits. 1 Rated in accordance with ARI Standard 110, utilization range A. 2 Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection. 3 Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection. 4 The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value Page: 139

24 Air Conditioners 13+ SEER Acclimate Series LXAL3B024F1 * 2.0 TON 13 SEER AIR CONDITIONER R410A $2, LXAL3B030F1 * 2.5 TON 13 SEER AIR CONDITIONER R410A $2, LXAL3B036F1 * 3.0 TON 13 SEER AIR CONDITIONER R410A $2, LXAL3B042F1 * 3.5 TON 13 SEER AIR CONDITIONER R410A $3, LXAL3B048F1 * 4.0 TON 13 SEER AIR CONDITIONER R410A $3, Luxaire LXAL3B ACCLIMATE Air Conditioner using R-410A Capacities: 1.5 Thru 5.0 Tons Efficiency: 13 SEER Warranty 10-year limited parts warranty. 10-year limited compressor warranty. Acclimate LXAL3B Split System Air Conditioner - 13 SEER R-410A 1 Phase The LXAL3B 13 SEER Series unit is the outdoor part of a versatile climate system. It is designed with a matching indoor coil component from Johnson Controls Unitary Products. Available for typical applications this climate system is supported with accessories and documents to serve specific functions. Special Benefits Superior Coil Protection A Stamped coil guard completely protects coil from debris and other large damaging material while a polymer mesh further protects the coil against smaller particles. Isolated Compressor Compartment A molded composite bulkhead isolates the compressor from the rest of the unit reducing sound and vibration. Protected Compressors Each compressor is protected against abnormal pressures by an internal pressure relief valve and factory installed high and low pressure controls. Additional protection against moisture and debris is provided by factory installed liquid line filter driers. Environmentally Friendly Refrigerant Next generation refrigerant R-410A delivers environmentally friendly performance with zero ozone depletion. Durable Finish Automotive quality finish provides the ultimate protection from harmful U.V. rays and rust creep ensuring long-lasting high quality appearance. A powder-paint topcoat is applied over a baked-on primer, using a galvanized, zinc coated steel base material. The result is a finish that has been proven in testing to provide 33% greater durability than conventional powder-coat finishes. Lower Installed Cost Designed to provide enhanced instability by featuring a slide-down control compartment and angled service valves to reduce overall installation time and cost. Low Operating Sound Levels A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper quiet operation by allowing airflow to flow smoothly and efficiently across the fan tips. Filter-Drier A factory installed, solid core liquid line filter-drier, filters harmful debris and moisture from the system. Easy Service Access A full end, full service, access panel with handle makes for easy entry to internal components. Composite Base - Strong and durable composite base pan resists rust and corrosion while it helps reduce vibrations and noise. Silent drive system - Features combination of swept-wing fan, composite base pan, isolated compressor compartment and two-stage compressor to reduce overall sound to a mere whisper. Low RPM fan motor - Helps to reduce airflow noise. Agency Listed - U.L. and C.U.L. listed - approved for outdoor application. The unit is certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/ Page: 140

25 Air Conditioners 13+ SEER Acclimate Series Model LXAL3B018 LXAL3B024 LXAL3B030 LXAL3B036 LXAL3B042 LXAL3B048 LXAL3B060 F1 F1 F1 F1 F1 F1 F1 Unit Supply Voltage V, 60Hz, 1 Phase Normal Voltage Range to 252 Minimum Circuit Ampacity Max. Overcurrent Device Amps Min. Overcurrent Device Amps Compressor Type Scroll Scroll Scroll Scroll Scroll Scroll Scroll Compressor Amps Rated Load Locked Rotor Crankcase Heater No No No No No No No Fan Motor Amps Rated Load Fan Diameter Inches Rated HP 1/15 1/15 1/15 1/4 1/4 1/4 1/4 Fan Motor Nominal RPM Nominal CFM ,250 2,300 3,200 3,250 3,500 3,500 Face Area Sq. Ft Coil Rows Deep Fins / Inch Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line Set OD (Field Installed) 3/4 3/4 3/4 3/4 7/8 7/8 7/8 Unit Charge (Lbs. - Oz.) Charge Per Foot Oz Operating Weight Lbs Rated in accordance with ARI Standard 110, utilization range A. 2 Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection. 3 Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection. 4 The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value Page: 141

26 Heat Pumps 18+ SEER Acclimate Series LXHL8B036F1 * 3.0 TON 18 SEER 2 STAGE HEAT PUMP R410A $6, LXHL8B048F1 * 4.0 TON 18 SEER 2 STAGE HEAT PUMP R410A $7, Luxaire LXHL8B Acclimate 18 SEER Split System Heat Pump using R-410A Capacities: Mbh, 3 4 Tons Efficiency: 18 SEER Warranty 10-year limited parts warranty. 10-year limited compressor warranty. Acclimate LXHL8B 18 SEER Split System Heat Pump The LXHL8B Series unit is the outdoor part of a versatile heat pump system. It is designed to be custom matched with one of our complete line of evaporator sections, each designed to serve a specific function. Matching air handlers are available for up-flow, down-flow and horizontal left or right applications to provide a complete system. Electric heaters are available if required. Add-on coils are available for use with up-flow, down-flow or horizontal furnaces. Field installed accessories are available as needed. Special Benefits Superior Coil Protection - A PVC coated steel coil guard completely protects coil from debris and other large damaging material while a polymer mesh further protects the coil against smaller particles. Isolated Compressor Compartment - A molded composite bulkhead isolates the compressor from the rest of the unit reducing sound and vibration. Protected Compressors - Each compressor is protected against high and low pressure as well as excessive temperature. This is accomplished by the simultaneous operation of high pressure relief valve and temperature sensors which protect the compressor if undesirable conditions occur. A factory installed liquid line filter drier further protects the compressor. Environmentally Friendly Refrigerant - Next generation refrigerant R-410a delivers environmentally friendly performance with zero ozone depletion. Durable Finish - Automotive quality finish provides the ultimate protection from harmful U.V. rays as well as rust creep ensuring long-lasting high quality appearance. A powder-paint topcoat is applied over a baked-on primer, using a galvanized, zinc coated steel base material. The result is a finish that has been proved in testing to provide 33% greater durability than conventional powder-coat finishes. Lower Installed Cost - Designed to provide enhanced install-ability by featuring a slide-down control compartment allowing easy access to control components along with angled service valves to reduce overall installation time and cost. Low Operating Sound Levels - A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper quiet operation by allowing airflow to flow smoothly and efficiently across the fan tips. Filter-Drier - A factory installed, solid core liquid line filter-drier filters harmful debris and moisture from the system. Easy Service Access - A full end, full service, access panel with handle makes for easy entry to internal components. Long Lasting Operation - Strong and durable composite base pan provides added strength while resisting rust and corrosion as well as reducing sound and vibration. Silent Drive System - Features combination of swept-wing fan, composite base pan, isolated compressor compartment and twostage compressor to reduce overall sound to a mere whisper. Complete System Control - These heat pumps utilize the unique microprocessor defrost control system to provide optimal comfort as well as monitor the overall system for reliable operation. In the event improper operating conditions occur (high temperature and/or high pressure), the system will automatically shut the system down to extend the life of the heat pump. The defrost control features an internal memory to aid the technician in troubleshooting, reducing service time and cost Page: 142

27 Heat Pumps 18+ SEER Acclimate Series Mo del LXHL8B036 LXHL8B048 F1 F1 Unit Supply Voltage V, 60Hz, 1 Phase Normal Voltage Range to 252 Minimum Circuit Ampacity Max. Overcurrent Device Amps Min. Overcurrent Device Amps Multi-stage Compressor Yes Yes Compressor Type Scroll Scroll Compressor Amps Rated Load Locked Rotor Crankcase Heater No No Fan Motor Amps Rated Load Fan Diameter Inches Rated HP 1/3 1/3 Fan Motor Nominal RPM Nominal CFM 2,666 3,376 Face Area Sq. Ft Coil Rows Deep 2 2 Fins / Inch Liquid Line Set OD (Field Installed) 3/8 3/8 Vapor Line Set OD (Field Installed) 3/4 7/8 Unit Charge (Lbs. - Oz.) Charge Per Foot Oz Operating Weight Lbs Rated in accordance with ARI Standard 110, utilization range A. 2 Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection. 3 Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection. 4 The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value. Refrigerant Connection Service Dimensions (Inches) Valve Size Model A B C Liquid Vapor LXHL8B036F1 39 1/ /8" 3/4" LXHL8B048F1 39 1/ /8" 7/8" Page: 143

28 Heat Pumps 15+ SEER Acclimate Series LXHL5B024F1 * 2.0 TON 15 SEER 2 STAGE HEAT PUMP R410A $4, LXHL5B036F1 * 3.0 TON 15 SEER 2 STAGE HEAT PUMP R410A $4, LXHL5B048F1 * 4.0 TON 15 SEER 2 STAGE HEAT PUMP R410A $5, Luxaire LXHL5B Acclimate 15 SEER Split System Heat Pump using R-410A Capacities: Mbh, 2 4 Tons Efficiency: 15 SEER Warranty 10-year limited parts warranty. 10-year limited compressor warranty. Premium System Warranty - Limited lifetime compressor when matched with an approved Luxaire Acclimate furnace or UPG air handler and coil. Acclimate LXHL5B 15 SEER Split System Heat Pump using R-410A The LXHL5B 15 SEER Series unit is the outdoor part of a versatile climate system. It is designed with a matching indoor coil component from Johnson Controls Unitary Products. Available for typical applications this climate system is supported with accessories and documents to serve specific functions. Special Benefits Superior Coil Protection - A PVC coated steel coil guard completely protects coil from debris and other large damaging material while a polymer mesh further protects the coil against smaller particles. Isolated Compressor Compartment - A molded composite bulkhead isolates the compressor from the rest of the unit reducing sound and vibration. Protected Compressors - Each compressor is protected against high and low pressure as well as excessive temperature. This is accomplished by the simultaneous operation of high pressure relief valve and temperature sensors which protect the compressor if undesirable conditions occur. A factory installed liquid line filter drier further protects the compressor. Environmentally Friendly Refrigerant - Next generation refrigerant R-410a delivers environmentally friendly performance with zero ozone depletion. Durable Finish - Automotive quality finish provides the ultimate protection from harmful U.V. rays as well as rust creep ensuring long-lasting high quality appearance. A powder-paint topcoat is applied over a baked-on primer, using a galvanized, zinc coated steel base material. The result is a finish that has been proved in testing to provide 33% greater durability than conventional powder-coat finishes. Lower Installed Cost - Designed to provide enhanced install-ability by featuring a slide-down control compartment allowing easy access to control components along with angled service valves to reduce overall installation time and cost. Low Operating Sound Levels - A fan design boasting technology adapted from aeronautic and defense engineering provides for whisper quiet operation by allowing airflow to flow smoothly and efficiently across the fan tips. Filter-Drier - A factory installed, solid core liquid line filter-drier filters harmful debris and moisture from the system. Easy Service Access - A full end, full service, access panel with handle makes for easy entry to internal components. Long Lasting Operation - Strong and durable composite base pan provides added strength while resisting rust and corrosion as well as reducing sound and vibration. Silent Drive System - Features combination of swept-wing fan, composite base pan, isolated compressor compartment and twostage compressor to reduce overall sound to a mere whisper. Complete System Control - These heat pumps utilize the unique microprocessor defrost control system to provide optimal comfort as well as monitor the overall system for reliable operation. In the event improper operating conditions occur (high temperature and/or high pressure), the system will automatically shut the system down to extend the life of the heat pump. The defrost control features an internal memory to aid the technician in troubleshooting, reducing service time and cost. Agency Listed - U.L. and C.U.L. listed - approved for outdoor application. The unit is certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/ Page: 144

29 Heat Pumps 15+ SEER Acclimate Series Model LXHL5B024 LXHL5B036 LXHL5B048 F1 F1 F1 Unit Supply Voltage V, 60Hz, 1 Phase Normal Voltage Range to 252 Minimum Circuit Ampacity Max. Overcurrent Device Amps Min. Overcurrent Device Amps Multi-stage Compressor Yes Yes Yes Compressor Type Scroll Scroll Scroll Compressor Amps Rated Load Locked Rotor Crankcase Heater No No No Fan Motor Amps Rated Load Fan Diameter Inches Rated HP 1/4 1/4 1/4 Fan Motor Nominal RPM Nominal CFM Face Area Sq Ft. Coil Rows Deep Fins / Inch Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 Vapor Line Set OD (Field Installed) 3/4 3/4 7/8 Unit Charge (Lbs. - Oz.) Charge Per Foot Oz Operating Weight Lbs Rated in accordance with ARI Standard 110, utilization range A. 2 Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection. 3 Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection. 4 The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value. Dimensions are in inches. Subject to change without notice. Certified dimensions provided upon request. Refrigerant Connection Service Dimensions (Inches) Valve Size Model A B C Liquid Vapor LXHL5B024F1 33 1/ /8" 3/4" LXHL5B036F1 33 1/ /8" 3/4" LXHL5B048F1 33 1/ /8" 7/8" Page: 145

30 Heat Pumps 13+ SEER LX Series - High Efficiency LXLHJD18S41S1 * 1.5 TON 13 SEER HEAT PUMP R410A $2, LXLHJD24S41S1 * 2.0 TON 13 SEER HEAT PUMP R410A $2, LXLHJD30S41S1 * 2.5 TON 13 SEER HEAT PUMP R410A $2, LXLHJD36S41S1 * 3.0 TON 13 SEER HEAT PUMP R410A $3, LXLHJD42S41S1 * 3.5 TON 13 SEER HEAT PUMP R410A $3, LXLHJD48S41S1 * 4.0 TON 13 SEER HEAT PUMP R410A $3, LXLHJD60S41S1 * 5.0 TON 13 SEER HEAT PUMP R410A $4, Luxaire LXLHJD LX High Efficiency 13 SEER Split System Heat Pump w/r-410a Capacities: Mbh, 1.5 Thru 5.0 Tons Efficiency: 13 SEER Warranty 10-year limited parts warranty. 10-year limited compressor warranty. LX Series High Efficiency 13 SEER Split System Heat Pump w/r-410a The LXLHJD LX Series High Efficiency heat pump condensing unit is the outdoor part of a versatile system of heating and air conditioning. It is designed to be custom matched with one of our indoor evaporator sections, each designed to serve a specific function for either furnace and/or air handler applications. All units are factory charged to assure optimum performance and easy installation. All models are hybrid heat compatible. Special Benefits QUALITY CONDENSER COILS - The coil is constructed of copper tubing and enhanced aluminum fins for increased efficiency and corrosion protection. PROTECTED COMPRESSOR - The compressor is internally protected against high pressure, temperature, and externally by a factory installed high pressure switch. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sens or which protects the compress or if undesirable operating conditions occ ur. A liquid line filter-drier further protects the compressor. DURABLE FINISH - The c abinet is made of pre-painted steel. The pre-treated galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted-textured finish insure less fading when exposed to sunlight. LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof. TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applic ations. LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. LOW MAINTENANCE - Long life permanently lubricated motor-bearings need no annual servicing. EASY SERVICE ACCESS - Fully exposed refrigerant connections, and a single panel covering the electrical controls make for easy servicing of the unit. SECURED SERVICE VALVES - Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging. U.L. and C.U.L. listed - approved for outdoor application. Agency Listed - U.L. and C.U.L. listed - approved for outdoor application. The unit is certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/ Page: 146

31 Heat Pumps 13+ SEER LX Series - High Efficiency Model LXLHJD18 LXLHJD24 LXLHJD30 LXLHJD36 LXLHJD42 LXLHJD48 LXLHJD60 S41S1 S41S1 S41S1 S41S1 S41S1 S41S1 S41S1 Unit Supply Voltage V, 60Hz, 1 Phase Normal Voltage Range to 252 Minimum Circuit Ampacity Max. Overcurrent Device Amps Min. Overcurrent Device Amps Compressor Type Recip Recip Recip Recip Scroll Scroll Scroll Compressor Amps Rated Load Locked Rotor Crankcase Heater Yes Yes Yes Yes No No No Fan Motor Amps Rated Load Fan Diameter Inches Rated HP 1/10 1/8 1/8 1/4 1/4 1/4 1/4 Fan Motor Nominal RPM Nominal CFM Face Area Sq. Ft Coil Rows Deep Fins / Inch Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line Set OD (Field Installed) 3/4 3/4 3/4 3/4 7/8 7/8 7/8 Unit Charge (Lbs. - Oz.) Charge Per Foot Oz Operating Weight Lbs Rated in accordance with ARI Standard 110, utilization range A. 2 Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection. 3 Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection. 4 The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value Page: 147

32 Heat Pumps 13+ SEER Climasure Series LXTHGD24S41S1 * 2.0 TON 13 SEER HEAT PUMP R410A $2, LXTHGD30S41S1 * 2.5 TON 13 SEER HEAT PUMP R410A $2, LXTHGD36S41S1 * 3.0 TON 13 SEER HEAT PUMP R410A $2, LXTHGD42S41S1 * 3.5 TON 13 SEER HEAT PUMP R410A $3, LXTHGD48S41S1 * 4.0 TON 13 SEER HEAT PUMP R410A $3, LXTHGD60S41S1 * 5.0 TON 13 SEER HEAT PUMP R410A $4, Luxaire LXTHGD Climasure 13 SEER Split System Heat Pump using R-410A Capacities: 2.0 Thru 5.0 Nominal Tons Efficiency: 13 SEER Warranty 10-year limited parts warranty. 10-year limited compressor warranty. Climasure LXTHGD 13 SEER Split System Heat Pump The LXTHGD Climasure heat pump condensing unit is the outdoor part of a versatile system of heating and air conditioning. It is designed to be custom matched with one of our indoor evaporator sections, each designed to serve a specific function for either furnace and/or air handler applications. All units are factory charged to assure optimum performance and easy installation. All models are hybrid heat compatible. Special Benefits QUALITY CONDENSER COILS - The coil is constructed of copper tubing and enhanc ed aluminum fins for increased efficiency and corrosion protection. PROTECTED COMPRESSOR - The compressor is internally protected against high pressure, temperature, and externally by a factory installed high pressure switch. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor. DURABLE FINISH - The c abinet is made of pre-painted steel. The pre-treated galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted-textured finish insure less fading when exposed to sunlight. LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof. TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications. LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. LOW MAINTENANCE - Long life permanently lubricated motor-bearings need no annual servicing. EASY SERVICE ACCESS - Fully exposed refrigerant connections, and a single panel covering the electrical controls make for easy servicing of the unit. SECURED SERVICE VALVES - Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging. U.L. and C.U.L. listed - approved for outdoor application. Agency Listed - U.L. and C.U.L. listed - approved for outdoor application. The unit is certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/ Page: 148

33 Heat Pumps 13+ SEER Climasure Series Model LXTHGD24 LXTHGD30 LXTHGD36 LXTHGD42 LXTHGD48 LXTHGD60 S41S1 S41S1 S41S1 S41S1 S41S1 S41S1 Unit Supply Voltage Normal Voltage Range 1 Minimum Circuit Ampacity Max. Overcurrent Device Amps Min. Overcurrent Device Amps Compressor Type Recip Recip Recip Scroll Scroll Scroll Compressor Amps Rated Load Locked Rotor Crankcase Heater Yes Yes Yes No No No Fan Motor Amps Rated Load Fan Diameter Inches Rated HP 1/8 1/8 1/4 1/4 1/4 1/4 Fan Motor Nominal RPM Nominal CFM Face Area Sq. Ft Coil Rows Deep Fins / Inch Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line Set OD (Field Installed) 3/4 3/4 3/4 7/8 7/8 7/8 Unit Charge (Lbs. - Oz.) Charge Per Foot Oz Operating Weight Lbs Rated in accordance with ARI Standard 110, utilization range A. 2 Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection. 3 Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection. 4 The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value. Dimensions (Inches) Model A 1 B C LXTHGD24S41S LXTHGD30S41S LXTHGD36S41S LXTHGD42S41S LXTHGD48S41S LXTHGD60S41S Including Fan Guard Refrigerant Connection Service Valve Size 3/8" 3/4" 7/8" Page: 149

34 Cased Coils Upflow/Downflow Flex Coil LXFC18B3XN1 * 1.5 TON 17.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC24A3XN1 * 2.0 TON 14.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC24B3XN1 * 2.0 TON 17.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC30B3XN1 * 2.5 TON 17.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC32A3XN1 * 2.5 TON 14.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC35B3XN1 * 2.5 TON 17.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC35B3XN2 * 3.0 TON 17.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC35C3XN1 * 2.5 TON 21.0 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC36A3XN1 * 3.0 TON 14.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC36B3XN1 * 3.0 TON 17.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC36C3XN1 * 3.0 TON 21.0 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC37A3XN1 * 3.0 TON 14.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC42B3XN1 * 3.5 TON 17.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC42C3XN1 * 3.5 TON 21.0 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC43B3XN1 * 3.5 TON 17.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC43C3XN1 * 3.5 TON 21.0 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC48C3XN1 * 4.0 TON 21.0 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC48D3XN1 * 4.0 TON 24.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC60C3XN1 * 5.0 TON 21.0 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC60D3XN1 * 5.0 TON 24.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ LXFC62D3XN1 * 5.0 TON 24.5 UPFLOW/DOWNFLOW FLEX COIL (ADD TXV KIT) $ Dimensions FC Coils Refrigerant Line Size 1 Factory Model A B C D Liquid Vapor Installed TXV FC18B3XN / /8 3/4 None FC24A3XN / /8 3/4 None FC24B3XN / /8 3/4 None FC30B3XN / /8 3/4 None FC32A3XN / /8 3/4 None FC35B3XN / /8 3/4 None FC35B3XN / /8 3/4 None FC35C3XN /8 20 3/8 7/8 None FC36A3XN / /8 7/8 None FC36B3XN / /8 7/8 None FC36C3XN /8 20 3/8 3/4 None FC37A3XN / /8 3/4 None FC42B3XN / /8 7/8 None FC42C3XN /8 20 3/8 7/8 None FC43B3XN / /8 7/8 None FC43C3XN /8 20 3/8 7/8 None FC48C3XN /8 20 3/8 7/8 None Special Benefits: Thermal Expansion Valve Pr ovides flexibility to convert any coil to R22 or R410A refrigerant. A true bolt-on TXV, valve assembly and equalizer tube are bolt-on, no brazing required. TXV and sensing bulb are mounted inside the FC48D3XN1 FC60C3XN1 FC60D3XN1 FC62D3XN /8 19 7/8 23 3/8 23 3/ /8 3/8 3/8 3/8 7/8 7/8 7/8 7/8 None None None None cased coil cabinet. (Must be field supplied for all Flex-coils ) Insulated Cabinet All evaporator coil cabinets are thermally insulated with foil faced insulation to prevent sweating. Internally Clean All evaporator coils are factory leak-tested, dehydrated, sealed and shipped with a holiday charge. The suction and liquid lines are sealed with rubber plugs, no cutting of connection stubs to attach line set. Durable Finish Inside and Out: Coil casings are made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resist corrosion and rust creep. All internal metal parts are made of G90 pre-painted steel i.e. triangular plated, top plates, horizontal supports etc. Optimum Heat Transfer: Using the latest in heat transfer technology, staggered rows of copper tubes are mechanically expanded into aluminum fins to provide optimum air to surface contact for ample moisture removal as well as high performance ratings Page: 150

35 Cased Coils Multi-Position Flex Coil LXMC18A3XH1 * 1.5 TON 14.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC24A3XH1 * 2.0 TON 14.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC24B3XH1 * 2.0 TON 17.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC30A3XH1 * 2.5 TON 14.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC32A3XH1 * 2.5 TON 14.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC35B3XH1 * 2.5 TON 17.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC36A3XH1 * 3.0 TON 14.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC36B3XH1 * 3.0 TON 17.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC36C3XH1 * 3.0 TON 21.0 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC37A3XH1 * 3.0 TON 14.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC42B3XH1 * 3.5 TON 17.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC42C3XH1 * 3.5 TON 21.0 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC43B3XH1 * 3.5 TON 17.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC48C3XH1 * 4.0 TON 21.0 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC48D3XH1 * 4.0 TON 24.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC60D3XH1 * 5.0 TON 24.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $ LXMC62D3XH1 * 5.0 TON 24.5 MULTI-POSITION FLEX COIL (ADD TXV KIT) $1, Refrigerant Factory Dimensions MC Coils Line Size 1 Liquid Installed A B C D Model Vapor TXV MC18A3XH /8 3/4 None MC24A3XH /8 3/4 None MC24B3XH /8 3/4 None MC30A3XH /8 3/4 None MC32A3XH /8 3/4 None MC35B3XH /8 3/4 None MC36A3XH /8 7/8 None MC36B3XH /8 7/8 None MC36C3XH /8 7/8 None MC37A3XH /8 3/4 None MC42B3XH /8 7/8 None MC42C3XH /8 7/8 None MC43B3XH /8 7/8 None MC48C3XH /8 20 3/8 7/8 None MC48D3XH /8 7/8 None MC60D3XH /8 7/8 None MC62D3XH /8 7/8 None Special Benefits: Thermal Expansion Valve Provides flexibility to convert any coil to R22 or R410A refrigerant. A true bolt-on TXV, valve assembly and equalizer tube are bolt-on, no brazing required. TXV and sensing bulb are mounted inside the cased coil cabinet. (Must be field supplied for all Flex-coils ) Insulated Cabinet All evaporator coil cabinets are thermally insulated with foil faced insulation to prevent sw eating. Internally Clean All evaporator coils are facto ry leak-tested, dehydrated, sealed and shipped with a holiday charge. The suction and liquid lines are sealed with rubber plugs, no cutting of connection stubs to attach line set. Durable Finish Inside and Out: Coil casings are made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resist corrosion and rust creep. All internal metal parts are made of G90 pre-painted steel i.e. triangular plated, top plates, horizontal supports etc. Optimum Heat Transfer: Using the latest in heat transfer technology, staggered rows of copper tubes are mechanically expanded into aluminum fins to provide optimum air to surface contact for ample moisture removal as well as high performance ratings Page: 151

36 Accessories Air Handlers Strip Heat S1-4HK * 5KW STRIP HEAT WITH BREAKER 208/230V 1-PH $ S1-4HK * 8KW STRIP HEAT WITH BREAKER 208/230V 1-PH $ S1-4HK * 10KW STRIP HEAT WITH BREAKER 208/230V 1-PH $ S1-4HK * 15KW STRIP HEAT WITH BREAKER 208/230V 1-PH $ S1-4HK * 20KW STRIP HEAT WITH BREAKER 208/230V 1-PH $ S1-4HK * 25KW STRIP HEAT WITH BREAKER 208/230V 1-PH $ S1-4HK165N1506 * 15KW STRIP HEAT WITH BREAKER 208/230V 1-PH (NARROW FOR MA/MV12B $ AIR HANDLER) Thermal Expansion Valves S1-1TVM4A1 * R-410A BOLT ON TXV KIT FOR LUXAIRE FLEX-COILS $63.42 S1-1TVM4E1 * R-410A BOLT ON TXV KIT FOR LUXAIRE FLEX-COILS $63.90 S1-1TVM4F1 * R-410A BOLT ON TXV KIT FOR LUXAIRE FLEX-COILS $ S1-1TVM4G1 * R-410A BOLT ON TXV KIT FOR LUXAIRE FLEX-COILS $ S1-1TVM4H1 * R-410A BOLT-ON TXV KIT FOR LUXAIRE FLEX-COILS $ S1-1TVM4J1 * R-410A BOLT ON TXV KIT FOR LUXAIRE FLEX-COILS $ S1-1TVM4K1 * R-410A BOLT ON TXV KIT FOR LUXAIRE FLEX-COILS $ S1-1TVM4M1 * R-410A BOLT ON TXV KIT FOR LUXAIRE FLEX-COILS $63.90 R-410A TXV SELECTOR TXV AIR CONDITIONERS HEAT PUMPS AL8B AL5B AL3B LCJF LCJD TCGD HL8B HL5B HL3B LHJD THGD S1-1TVM4A1 24, S1-1TVM4E S1-1TVM4F , , 24 18, 24 24, S1-1TVM4G1 24, 30, 36 30, 36, 42 36, 42 36, , 30 24, 30 S1-1TVM4H , 42 36, 42 36, 42 S1-1TVM4J , 60 48, S1-1TVM4K , 48, S1-1TVM4M Whip Kits S1-6126NM * 1/2"x6 NON-METAL WHIP, 10 GUAGE $25.88 S1-6346NM * 3/4"x6 NON-METAL WHIP, 8 GUAGE $ Page: 152

37 Accessories Line Sets Equipment Pads Condensate Pumps LS /8 x 3/4 x 35 LINE SET $ LS /8 x 3/4 x 50 LINE SET $ LS /8 x 5/8 x 35 LINE SET $ LS /8 x 5/8 x 50 LINE SET $ LS /8 x 7/8 x 35 LINE SET $ LS /8 x 7/8 x 50 LINE SET $ LS /8 x 1 1/8 x 50 LINE SET $ CORKTAPE 1/8"x2"x30 CORK INSULATION TAPE FOR WRAPPING HOT & COLD PIPES $20.96 THUMGUM SEALING COMPOUND - 1LB BAG $6.12 CP "x30"x3" ULTRA LITE PAD $63.40 CP "x36"x3" ULTRA LITE PAD $93.64 CP "x48"x3" ULTRA LITE PAD $ VP44 4"x4"x7/8" CORK-CORE VIBRATION PADS $6.64 PUMPUP CONDENSING UNIT PUMP-UP $8.62 SKU Descrpition U/M List BCP 115V CONDENSATE PUMP $99.20 BCPLP * 115V LOW PROFILE CONDENSATE PUMP W/CHECK VALVE AND SAFETY $ SWITCH - 20 LIFT BVH 3/8" x 100 VINYL CONDENSATE TUBING $35.70 HM38 * NYLON HOSE MENDER 3/8" BARB X 3/8" BARB (5 PER PACK) pk $5.00 Drain Pans CDP x60 CONDENSATE DRAIN PAN $83.96 Fuses FUSE15 15 AMP DUAL CARTRIDGE FUSE $3.80 FUSE20 20 AMP DUAL CARTRIDGE FUSE $3.80 FUSE25 25 AMP DUAL CARTRIDGE FUSE $3.80 FUSE30 30 AMP DUAL CARTRIDGE FUSE $7.00 FUSE35 35 AMP DUAL CARTRIDGE FUSE $7.00 FUSE40 40 AMP DUAL CARTRIDGE FUSE $7.00 FUSE45 45 AMP DUAL CARTRIDGE FUSE $7.00 FUSE50 50 AMP DUAL CARTRIDGE FUSE $7.00 FUSE60 60 AMP DUAL CARTRIDGE FUSE $ Page: 153

38 Accessories Disconnects S1-ACD30 * 30A FUSIBLE DISCONNECT $27.60 S1-ACD60 * 60A FUSIBLE DISCONNECT $30.20 Base Cans BCFURNA18 * 24GA BASE CAN FOR A CABINET GAS FURNACE 15"X26"X18"H-W/1" LINER END CAP, FURNACE RAIL BCFURNA36 * 24GA BASE CAN FOR A CABINET GAS FURNACE 15"X26"X36"H-W/1" LINER END CAP, FURNACE RAIL BCFURNB18 * 24GA BASE CAN FOR B CABINET GAS FURNACE 18"X26"X18"H-W/1" LINER END CAP, FURNACE RAIL BCFURNB36 * 24GA BASE CAN FOR B CABINET GAS FURNACE 18"X26"X36"H-W/1" LINER END CAP, FURNACE RAIL BCFURNC18 * 24GA BASE CAN FOR C CABINET GAS FURNACE 21.5"X26"X18"H - W/1" LINER END CAP, FURNACE RAIL BCFURNC36 * 24GA BASE CAN FOR C CABINET GAS FURNACE 21.5"X26"X36"H-W/1" LINER END CAP, FURNACE RAIL BCFURND18 * 24GA BASE CAN FOR D CABINET GAS FURNACE 25"X26"X18"H - W/1" LINER END CAP, FURNACE RAIL BCFURND36 * 24GA BASE CAN FOR D CABINET GAS FURNACE 25"X26"X36"H-W/1" LINER END CAP, FURNACE RAIL BCMBB24 * 26GA BASE CAN FOR B CABINET MODULATING BLOWER 18"X21"X24"H-W/1" LINER END CAP, FURNACE RAIL BCMBC24 * 26GA BASE CAN FOR C CABINET MODULATING BLOWER 21.5"X21"X24"H - W/1" LINER END CAP, FURNACE RAIL BCMBD24 * 26GA BASE CAN FOR D CABINET MODULATING BLOWER 25"X21"X24"H - W/1" LINER END CAP, FURNACE RAIL $ $ $ $ $ $ $ $ $ $ $ Page: 154

39 Accessories Top Cans Mini-Splits Air Conditioners Single Zone TCFURNA18 * 26GA BASE CAN FOR A CABINET GAS FURNACE 13-7/8"X20-1/2"X18"H-W/1" LINER, END CAP TCFURNA36 * 26GA BASE CAN FOR A CABINET GAS FURNACE 13-7/8"X20-1/2"X36"H - W/1" LINER, END CAP TCFURNB18 * 26GA BASE CAN FOR B CABINET GAS FURNACE 16-7/8"X20-1/2"X18"H - W/1" LINER, END CAP TCFURNB36 * 26GA BASE CAN FOR B CABINET GAS FURNACE 16-7/8"X20-1/2"X36"H - W/1" LINER, END CAP TCFURNC18 * 26GA BASE CAN FOR C CABINET GAS FURNACE 20-3/8"X20-1/2"X18"H - W/1" LINER, END CAP TCFURNC36 * 26GA BASE CAN FOR C CABINET GAS FURNACE 20-3/8"X20-1/2"X36"H - W/1" LINER, END CAP TCFURND18 * 26GA BASE CAN FOR D CABINET GAS FURNACE 23-7/8"X20-1/2"X18"H - W/1" LINER, END CAP TCFURND36 * 26GA BASE CAN FOR D CABINET GAS FURNACE 23-7/8"X20-1/2"X36"H - W/1" LINER, END CAP TCMBB24 * 26GA TOP CAN FOR B CABINET MODULATING BLOWER 15"X11"X24"H-W/1" LINER END CAP TCMBC24 * 26GA TOP CAN FOR C CABINET MODULATING BLOWER 18-3/4"X11"X24"H - W/1" LINER, END CAP TCMBD24 * 26GA TOP CAN FOR D CABINET MODULATING BLOWER 22"X11"X24"H - W/1" LINER, END CAP LGLSN122CE LGLSU122CE LGLSN182CE LGLSU182CE LGLSN242CE LGLSU242CE * 12K BTU MINI-SPLIT INDOOR UNIT 36V DC - HIGH WALL DUCT-FREE - SINGLE ZONE COOLING * 12K BTU MINI-SPLIT OUTDOOR UNIT 115/60/1 DUCT-FREE - SINGLE ZONE COOLING 13SEER - R410A * 18K BTU MINI-SPLIT INDOOR UNIT 36V DC - HIGH WALL DUCT-FREE - SINGLE ZONE COOLING * 18K BTU MINI-SPLIT OUTDOOR UNIT 115/60/1 DUCT-FREE - SINGLE ZONE COOLING 13SEER - R410A * 24K BTU MINI-SPLIT INDOOR UNIT 36V DC - HIGH WALL DUCT-FREE - SINGLE ZONE COOLING * 24K BTU MINI-SPLIT OUTDOOR UNIT 115/60/1 DUCT-FREE - SINGLE ZONE COOLING 13SEER - R410A $73.40 $ $88.60 $ $ $ $ $ $60.90 $73.08 $89.30 $ $1, $1, $2, $1, $2, Page: 155

40 Mini-Splits Heat Pumps Art Cool LGLAN091HNP * 9K BTU ART COOL PICTURE MINI-SPLIT INDOOR UNIT 36V DC - SINGLE ZONE HEAT PUMP - 13SEER - LGLAU091HNP * 9K BTU ART COOL PICTURE OUTDOOR UNIT 115/60/1 - SINGLE ZONE HEAT PUMP - 13 SEER - R410A LGLAN125HV * 12K BTU ART COOL MIRROR INVERTER SERIES INDOOR UNIT - SINGLE ZONE HEAT PUMP SEER LGLAU125HV * 12K BTU ART COOL MIRROR INVERTER SERIES OUTDOOR UNIT 208/230/60/1 - SINGLE ZONE HEAT LGLAN185HV * 18K BTU ART COOL MIRROR INVERTER SERIES INDOOR UNIT - SINGLE ZONE HEAT PUMP SEER LGLAU185HV * 18K BTU ART COOL MIRROR INVERTER SERIES OUTDOOR UNIT 208/230/60/1 - SINGLE ZONE HEAT LGLAN245HV * 24K BTU ART COOL MIRROR INVERTER SERIES INDOOR UNIT - SINGLE ZONE HEAT PUMP SEER LGLAU245HV * 24K BTU ART COOL MIRROR INVERTER SERIES OUTDOOR UNIT 208/230/60/1 - SINGLE ZONE HEAT $1, $1, $1, $1, $1, $2, $1, $2, Single Zone LGLSU122HE * 12K BTU MINI-SPLIT OUTDOOR UNIT 115/60/1 - SINGLE ZONE HEAT PUMP - 13 SEER - R410A LGLSN122HE * 12K BTU MINI-SPLIT INDOOR UNIT 36V DC - HIGH WALL DUCT-FREE - SINGLE ZONE HEAT PUMP - $1, $1, Line Sets LS143825FN LS143835FN LS143850FN LS141225FN LS141235FN LS141250FN LS145835FN LS145850FN LS385825FN LS385835FN LS385850FN * 1/4 X 3/8 X 25 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI SPLITS) * 1/4 X 3/8 X 35 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI SPLITS) * 1/4 X 3/8 X 50 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI SPLITS) * 1/4 X 1/2 X 25 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI-SPLITS) 1/4 X 1/2 X 35 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI-SPLITS) 1/4 X 1/2 X 50 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI-SPLITS) 1/4 X 5/8 X 35 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI-SPLITS) 1/4 X 5/8 X 50 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI-SPLITS) * 3/8 X 5/8 X 25 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI-SPLITS) 3/8 X 5/8 X 35 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI-SPLITS) 3/8 X 5/8 X 50 LINE SET W/FLARE NUTS & 3/8 INSULATION ON BOTH LINES (FOR MINI-SPLITS) $ $ $ $ $ $ $ $ $ $ $ Page: 156

41 Mini-Splits Thermostats LGDFSWLWTOA * WIRELESS WALL-MOUNT THERMOSTAT (FOR 2006 LG 13 SEER AND LATER UNITS ONLY!) $ Condensate Pumps LEC * LITTLE GIANT 115V CONDENSATE PUMP FOR MINI-SPLITS - 3PC DESIGN - 3 SUCTION TUBE (3/16" ID) LEC * LITTLE GIANT 115V CONDENSATE PUMP FOR MINI-SPLITS - 2PC DESIGN - 3 SUCTION TUBE (5/32" ID) LEC * LITTLE GIANT 230V CONDENSATE PUMP FOR MINI-SPLITS - 2PC DESIGN - 3 SUCTION TUBE (5/32" ID) LEC250 - Three-piece design (control unit, detection reservoir and pump) allows flexible installation for mini-split air conditioning units. Includes: Safety Switch, 3 Suction Tubing. 3/16 inside diameter. LEC400 Compact two-piece design allows flexible installation for most mini-split air conditioning units up to 25,000 BTU/hr. Includes: Suction Tubing 3 x 5/32 ID, Drain Tubing 3 x ½ ID, Tubing Adapter 5/32 x ¼, Safety Switch. $ $ $ Accessories SKU Descrpition U/M List LGADAP * MINI SPLITS OUTDOOR CHARGING ADAPTER - 1/4" S.A.E. M X 5/16" $32.40 FEMALE QUICK (RITCHIE YELLOW JACKET P/N 19173) SC378 * 3"X78" SPEEDI CHANNEL $44.80 SC390FB * 3" SPEEDI CHANNEL 90 DEGREE FLAT BEND $18.60 SC390INSIDE * 3" SPEEDI CHANNEL 90 DEGREE INSIDE ELBOW $16.62 SC390LFB * 3" SPEEDI CHANNEL 90 DEGREE LONG RADIUS FLAT BEND $23.40 SC390OUTSIDE * 3" SPEEDI CHANNEL 90 DEGREE OUTSIDE ELBOW $16.60 SC3FWE * 3" SPEEDI CHANNEL FLAT WALL ESCUTCHEON $8.70 SC3UC * 3" SPEEDI CHANNEL UNION COUPLING $6.90 SC3WE * 3" SPEEDI CHANNEL WALL ESCUTCHEON $9.76 SC3WPC * 3" SPEEDI CHANNEL WALL PENETRATION COVER $20.40 SC478 * 4" X 78" SPEEDI CHANNEL $63.90 SC4FWE * 4" SPEEDI CHANNEL FLAT WALL ESCUTCHEON $10.26 SC4TJ * 4" SPEEDI CHANNEL T-JOINT $72.00 SC4WE * 4" SPEEDI CHANNEL 4" WALL ESCUTCHEON $11.46 SC4WPC * 4" SPEEDI CHANNEL WALL PENETRATION COVER $34.80 SC34RC * 3" X 4" SPEEDI CHANNEL REDUCER COUPLING $12.50 MSDL34100 * 3/4" ID X 100 MINI SPLIT DRAIN LINE $ MSDA20 * 20mm MINI SPLIT DRAIN LINE ADAPTOR $8.74 SCCLIP * SPEEDI CLIP ea $ Page: 157