INSTALLATION INSTRUCTIONS ELECTRIC HEAT PACKAGES EHWA02-AXD EHWA02-AXH EHWA03-AXH EHWA03-AXK EHWA05-AXH EHWA05-AXK

Transcription

1 INSTALLATION INSTRUCTIONS ELECTRIC HEAT PACKAGES Models: EHWA02-AXD EHWA02-AXH EHWA03-AXH EHWA03-AXK EHWA05-AXH EHWA05-AXK For 2 thru 5 Ton WA Series Wall Mounted Air Conditioners BARD MANUFACTURING COMPANY Bryan, Ohio Since Moving ahead, just as planned. Manual: Supersedes: File: Volume III, Tab 18 Date: Copyright 2002

2 CONTENTS General Information Description of Equipment... 1 Nomenclature... 1 Important... 1 Shipping Damage... 1 Unpacking Electric Heat Package... 1 Wiring Main Power... 2 Installation Installation of Heater Package... 3 Tables Table 1 Electrical Data... 1 Table 2 Terminal and Screw Mounting... 6 Figures Figure 1 Electrical Connections... 2 Figure 2 Installation of Heater Package... 4 WA24, WA30, WA36 Models Figure 2A Installation of Heater Package... 5 WA423, WA484, WA602 Models Figure 3 Rod Support and Screw Mounting... 6 Figure 4A - 4D Terminal Identification... 7 Figure 5 Wiring Directions... 8 WA24, WA30, WA36 Models Figure 5A Wiring Directions... 9 WA423, WA484, WA602 Models Figure 6 Marking Serial Plate... 10

3 GENERAL INFORMATION DESCRIPTION OF EQUIPMENT The EHWA series electric heater packages are field installable heater packages suitable for use with Bard wall mount hi boy air conditioners and heat pumps. The packages consist of the electric heat strip, the heater control base which includes the heat contactors, and circuit breaker of pull disconnects, installation instructions and wiring diagrams. See Table 1 for nominal electrical data and BTU output. Before installation, check unit serial plate to insure the heater package model that you intend to install is listed as a heater package that is suitable for use with the Bard wall mount hi boy unit. See Figure 6. NOMENCLATURE ELECTRIC HEATER PACKAGE WALL MOUNT A = AIR CONDITIONER SUITABLE FOR USE IN /2 and 2 TON MODELS /2 and 3 TON MODELS /2, 4 and 5 TON MODELS EHW A 03 - A 05 NOMINAL KW 5 KW ELECTRICAL VERSION A - 240/208V - 1Ph IMPORTANT The equipment covered in this manual is to be installed by trained, experienced service and installation technicians. SHIPPING DAMAGE Upon receipt of equipment, the carton should be checked for external signs of shipping damage. If damage is found, the receiving party must contact the last carrier immediately, preferably in writing, requesting inspection by the carrier s agent. UNPACKING ELECTRIC HEAT PACKAGE Remove the heat package from the shipping carton. The heat package must consist of the following: 1. Basic heater. 2. Electric heat control base and wiring. 3. Installation instructions. 4. Wiring diagram (2), one to be applied to unit. 5. Adhesive label to remark serial plate to indicate new model number. This is attached to the front of these instructions. Heater Package Model Volts TABLE 1 ELECTRICAL DATA Phase Nominal KW Nominal BTU EHWA02-AXD 240/ / ,065 / 12,800 EHWA02-AXH 240/ / ,130 / 25,600 EHWA03-AXH 240/ / ,130 / 25,600 EHWA03-AXK 240/ / ,200 / 38,400 EHWA05-AXH 240/ / ,130 / 25,600 EHWA05-AXK 240/ / ,200 / 38,400 Page 1

4 WIRING MAIN POWER 1. On all installations, size unit power supply wiring for the minimum circuit ampacity requirement for the unit and heater package combination listed on the unit serial plate. For existing installations, addition or upgrading of a heater package may require that larger supply wires be run to the unit. Resize all power supply wires for the minimum circuit ampacity rating listed on the unit serial plate that is applicable for your combination of unit and heater package. WARNING 2. All heater packages covered by this manual are factory wired for a single supply circuit. The following heater packages are field convertible to a dual supply circuit if required or desired. EHWA05-AXK EHWA03-AXK 3. To convert the above heater packages to dual circuit configuration before installation, loosen 4 screws holding jumper bar in place. Remove jumper bar. Circuit A + B are now identified on the heater package. See Figure 1. Wire should be sized to the minimum circuit ampacity as specified on the serial plates of units that accept these heater packages for circuits A + B. Install properly sized power supply leads for the unit/heater combination minimum circuit ampacity as listed on the unit serial plate. Hazard of fire. Failure to install properly sized conductors could result in fire. FIGURE 1 ELECTRICAL CONNECTIONS MIS-365 Page 2

5 INSTALLATION INSTALLATION OF HEATER PACKAGE 1. Disconnect all power to unit before installation. WARNING Disconnect all power to unit before installing heater package. Hazard of electrical shock. Failure to disconnect power could result in injury or death. 2. Before installation, check unit serial plate to insure that the heater package model that you intend to install is listed as a heater package suitable for use with the unit. Under no circumstances shall a heater package be installed in a unit if the model number of the heater package does not appear on the unit serial plate. WARNING Install only heater packages listed on unit serial plate. Hazard of fire or electrical shock. Failure to install listed heater package could result in fire, injury or death. 3. Remove electric heater access panel and control panel cover, both inner and outer. See Figure 2 or 2A. 4. All heaters are installed with the thermal cutoffs positioned to the top of the unit. Install heat strip(s) through heater access opening. Position heat strip support rod in heater support hole 1, 2, or 3 as indicated in Table 1 and Figure 3. Secure in place with 2 sheet metal screws in mounting holes as indicated in Table 1 and Figure 3. On heater packages with 2 heat strips 10KW heater first in position closest to the outlet air frame. See Figures 4C. 5. Install heater control base into top of control panel as shown in Figure 5. Secure with 4 sheet metal screws provided. 6. Plug male 6 pin connector into mating connector mounted in control panel. See Figure Connect red compressor supply lead to L1 of terminal block. Connect black compressor supply lead to L2 of terminal block. If 3 phase, connect yellow supply lead to L3 of terminal block. See Figure 5 or 5A and wiring diagram. 8. Route wires from heater control base up through raceway or grommet in top right corner of control panel to the heaters. See Figure 5 or 5A. 9. Wire heater package per wiring diagram supplied with this heater package. All wires are stamped with wire numbers that correspond with terminal numbers on the wiring diagram and stamped numbers on the heat strip. Limit switch wires are terminated with insulated quick connect terminals. See Figure Attach adhesive wiring diagram directly above unit wiring diagram on inner control panel cover. 11. Recheck all wiring. Break out appropriate circuit breaker tabs on inner control panel cover to allow trip lever to protrude. Replace control panel and heater access panels 12. Resupply power to the unit and check for proper operation. 13. Remark serial plate with self-adhesive label attached to the front of this manual. See Figure 6. Page 3

6 FIGURE 2 INSTALLATION OF HEATER PACKAGE WA24, WA30 AND WA36 MODELS MIS-361 Page 4

7 FIGURE 2A INSTALLATION OF HEATER PACKAGE WA423, WA484 AND WA602 MODELS MIS-419 Page 5

8 TABLE 2 REFER TO FIGURES 3 AND 4 Heater Package Model Number 1 EHWA02-AX D 2 EHWA02-AX H 3 EHWA05-AX H 4 EHWA05-AX K 5 EHWA03-AX H 6 EHWA03-AX K Figure 4 Heater Terminal Identification Drawing Figure 3 Rod Support and Screw Mounting Position 4A 1 4B 1 4B C B D FIGURE 3 ROD SUPPORT AND SCREW MOUNTING POSITIONS MIS-358 Page 6

9 FIGURES 4A - 4D HEATER TERMINAL IDENTIFICATION DRAWINGS FIGURE 4A FIGURE 4C FIGURE 4B FIGURE 4D MIS-1738 Page 7

10 FIGURE 5 WIRING DIRECTIONS WA24, WA30 AND WA36 MODELS MIS-1741 Page 8

11 FIGURE 5A WIRING DIRECTIONS WA423, WA484 AND WA602 MODELS MIS-1742 Page 9

12 FIGURE 6 MARKING SERIAL PLATE LABEL MIS-1739 Page 10