OWNER'S MANUAL IMPORTANT: READ OWNER'S MANUAL CAREFULLY MODEL: TRIPLES PANTHER 20TD

Transcription

1 OWNER'S MANUAL IMPORTANT: READ OWNER'S MANUAL CAREFULLY MODEL: PANTHER 0TD FOR YOUR CONVENIENCE, RECORD THE FOLLOWING IMPORTANT INFORMATION TRIPLES --==--===:=NATIONWIDE SANITARY SOLUTIONS MODEL: SERIAL NUMBER: DATE PURCHASED: PURCHASED FROM: _

2 TABLE OF CONTENTS SAFETY PRECAUTIONS MACHINE COMPONENTS MACHINE SET UP 5 MACHINE INSTALLATION 5-6 MACHINE OPERATION 6-7 TANK DRAINING 7 BATTERY CHARGING 7-8 PREVENTATIVE MAINTENANCE 8-9 MACHINE STORAGE 9 BASIC TROUBLESHOOTING 0 PARTS BREAKDOWNS AND LISTS -7 WIRING DIAGRAM 8

3 SAFETY PRECAUTIONS This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only with recommended accessories. All operators shall read, understand and exercise the following safety precautions: ) DO T OPERATE MACHINE: Unless trained and authorized. Unless you have read and understand the operators manual. In flammable or explosive areas. If not in proper operating condition. In outdoor areas. ) BEFORE OPERATING MACHINE: Make sure all safety devices are in place and operate properly. ) WHEN USING MACHINE: Go slow on inclines and slippery surfaces. Follow all safety guidelines. Be very careful when using the machine in reverse. Report and fix any damage to machine prior to operating it. WHEN SERVICING MACHINE: (con't) Disconnect batteries prior to working on machine. Wear gloves when handling batteries or battery cables. A void any contact with battery acid. A void moving parts. Do not wear loose fitting clothing while servicing machine. faiih I M G : Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep battery compartment open when charging. faiih I M G : Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks. faiih I M G : Flammable materials or reactive metals can cause explosion or fire. Do not pick up. ) BEFORE LEAVING OR SERVICING MACHINE: Stop machine on level ground. Tum machine off. 5) WHEN SERVICING MACHINE: Read operators manual thoroughly prior to operating or servicing this machine. Use manufacturer supplied or approved replacement parts. Secure machine with wheel blocks prior to jacking the machine up. Use approved jack or hoist to safely elevate the machine.

4 MACHINE COMPONENTS Main power ON/OFF switch. Vacuum ON/OFF switch. Battery level meter. Brush ON/OFF switch 5. Brush pressure meter 6. Solution ON/OFF switch 7. Brush pressure UP/DOWN switch 8. Solution control knob 9. Speed control knob 0. Circuit breakers. Recovery tank drain hose. Squeegee adjustment nut & shaft. Squeegee assembly. Scrub head actuator 5. Solution tank level sight tube 6. Console adjustment levers 7. Rear solution fill 8. Reverse switch 9. Squeegee lift lever 0. Control housing. Operating triggers. Solution tank. Rear casters. Transport wheels 5. Scrub head 6. Scrub head skirt 7. Skirt housing latch 8. Protective rollers 9. Front solution fill 0. Recovery tank. Recovery tank lid

5 MACHINE SET UP & INSTALLATION UNCRATING MACHINE Be sure and check packing carton for any damage. Immediately report any damage to carrier. Check contents of package to ensure that the following items are included: Machine, batteries (x), squeegee assembly, battery charger, and pad driver. BATTERY CONNECTIONS The batteries are and charger are shipped separately and will need to be installed and connected as shown in the diagram below. : Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep battery compartment open when charging.. Be sure power switch is in the off position.. Open recovery tank to gain access to battery compartment.. Carefully place the two batteries into the compartment as shown in figure below. Place the battery brace at the rear of the two batteries. DO T DROP BATTERIES INTO COMPARTMENT!. Connect battery cables to posts in numbered order as shown in drawing below. (RED to POSITIVE and BLACK to NEGATIVE). Check battery meter to make sure batteries are fully charged. (see BATTERY CHARGING). Check that squeegee is properly installed.. Check that brush / pad is properly installed. INSTALLING PAD DRIVER OR BRUSH. Ensure that the machine is turned off. Raise the brush head assembly off the floor by pushing on the brush lift button on the control console.. Open the swing away skirts to gain access to the brush head assembly.. If using a pad driver, first attach the appropriate pad to the pad driver surface. 5. Mount the pad driver or brush to the drive motor hub by lining up the three studs with the three holes in the drive motor hub. Once in the holes, rotate the driver toward the spring clip to lock driver into place. MOUNTING THE SQUEEGEE. Pull back on the squeegee lift lever to raise the squeegee bracket up.. Loosen the two knobs on the squeegee and slide the squeegee into the slots at the rear of the squeegee bracket. (the wheels on the squeegee point to the back). Tighten the knobs securely.. Secure the vacuum hose on the pick-up tube of the squeegee. R E D B L A C K B A T T E R Y B R A C E C H A R G E R P L U G 5. Apply a coat or protective spray on the cable connections to prevent battery corrosion. MACHINE SET UP PRE-OPERATION CHECKS. Sweep or dust mop the surface to be cleaned. FILLING THE SOLUTION TANK. The PANTHER 0TD can be filled in two different locations: a. Front fill area for use with a hose or a bucket. b. Rear fill area for use with a hose only.. Determine which fill area you would like to use to fill the machine with water.. Fill solution tank with up to 5 gallons of water. (water temperature should not exceed 0 F) The clear tube in the back left of the

6 machine has gallon markers to help determine the water level in the solution tank : If you are filling the solution tank with a bucket, make sure the bucket is clean. This will prevent debris from clogging the lines or solenoid. : Do not put any flammable materials into solution tank. This can cause an explosion or a fire. Only use recommended cleaning chemicals. Contact your janitorial supply distributor for recommendations on proper chemicals. MACHINE OPERATION : Do not operate machine unless you have read and understand this manual.. Set control housing to a comfortable operating height by squeezing together the two thumb levers directly underneath the housing. (see machine components, item #6). Lower squeegee assembly to the floor by releasing the lift lever from its locked position. (see machine components, item #9). Lower the brush head assembly to the floor by pushing on the brush lift button on the control console. (see machine components, item #7). Turn main power to on position. (see machine components, item #) 5. Turn vacuum motor switch to on position. (see machine components, item #) 6. Turn the brush motor switch to on position. (see machine components, item #) a. Brushes will not spin until the operating triggers are pulled. 7. Turn the solution switch to on position. (see machine components, item #6) a. Solution will not begin to flow until the operating triggers are pulled. 8. To begin scrubbing, pull on one or both of the red operating triggers. (see machine components, item #) When these triggers are pulled, the brush will begin to spin, the solution will begin to flow, and the machine will propel itself. 9. This machine is self-propelled. The speed can be controlled by a dial located on the right side of the control housing. (see machine components, item #9) 0. This machine has reverse. In order to activate reverse, there is a toggle switch located on the left side of the control housing. (see machine components, item #8) The toggle switch must be pulled backwards and the red operating triggers must be pressed to activate reverse motion. : Do not keep the machine in the same position with the pad / brush spinning, or you could cause damage to the floor.. Adjust amount of solution flow by turning the solution control knob. Turn to the right for more solution, or turn left for less solution. (see machine components, item #8) WHILE OPERATING MACHINE. Occasionally look through the clear recovery tank lid to see if there is any foam build-up. If excessive foam is found, add defoamer to the recovery tank. : Foam must not enter the float shut-off screen, or damage can occur to the vacuum motor. Foam will not activate the machines float shut-off device.. Occasionally view the clear tube at the back left of the machine to check the amount of cleaning solution that is left in the machine.. Occasionally check the battery level meter. (see machine components, item #) When meter is in the red, recharge the batteries. : When battery meter is in the red, do not continue to operate the machine. Battery damage may result.. If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe the blades down with a damp cloth. : Do not use your fingers to wipe or remove debris from the blades, as injury may occur. 5. When the solution tank runs empty, turn off the brush switch, solution switch and raise the brush head. Keep the squeegee down and continue to vacuum until all the dirty water is

7 picked up. (see TANK DRAINING section to learn how to drain recovery and solution tanks) : The brush motors are circuit breaker protected to protect them from damage. If a breaker trips, it can t be reset immediately. You must first determine what caused the breaker to trip, and allow the motor to cool down before you can reset the breaker. The breakers are located on the back panel of the control housing. TANK DRAINING. Turn the power off on the machine. With the squeegee and brush head in their up position, transport machine to approved area for draining tank(s). DRAINING THE RECOVERY (DIRTY) TANK : Anytime scrubbing is completed, or when refilling solution tank, the recovery tank should be drained and cleaned. : If the recovery tank is not drained when the solution tank has been refilled, foam or water may enter the float shut-off mechanism and cause damage to the vacuum motor.. Remove the drain hose from the holder, and place the drain hose over the floor drain. Twist off the drain hose plug to begin the draining process. In order to completely empty the recovery tank, hinge open the recovery tank and let it rest on the support stand.. Clean the recovery tank after every use. Use a fresh water hose to rinse out the recovery tank. Be careful not to spray water into the float shut-off mechanism. : If you are storing the machine for any period of time, always leave the clear recovery tank lid off the tank so the tank can dry completely and smell fresh.. Replace the drain hose plug tightly as soon as you are done draining the tank. DRAINING THE SOLUTION (CLEAN) TANK : Anytime scrubbing operation is completed, the solution tank should be drained and cleaned.. Pull down on the clear tube (back left of the machine) to remove it from the hose barb. This will allow the solution to flow freely into a bucket or floor drain.. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines.. With clean water in solution tank, turn machine power on, solution switch on and pull the operating triggers. This will allow the clean water to flush through and clean the solution plumbing.. Once tank is rinsed, flushed and drained, reconnect the clear tube to the hose barb. Be sure the tube is pushed all the way up on the hose barb. BATTERY CHARGING : Use only approved chargers with the following specifications: Automatic shut off circuit Deep cycle charging Output current of 0 0 amps Output voltage of volts : For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition. : Batteries are dangerous! Batteries emit hydrogen gas and an explosion or fire can result. Keep sparks and fire away from batteries at all times. When charging the machine, make sure the battery compartment is left open.. Place charger and machine in a well ventilated area.. Turn machine off.. Open recovery tank up, exposing battery compartment. Check fluid level in each battery cell. Do not charge batteries unless fluid is slightly covering the battery plates. Do not overfill the

8

9

10 BASIC TROUBLESHOOTING PROBLEM CAUSE SOLUTION No power Bad batteries Replace batteries Key not in "ON" position Turn key "ON" Main circuit breaker tripped Contact Distributor Batteries need to be charged Charge batteries (see Battery Charging) Loose battery cable Tighten loose cable(s) Batteries not connected properly Follow battery installation instructions Brush motor does Bad brush switch Contact Distributor not run Brush circuit breaker has tripped Check brush motor for obstructions and reset breaker Bad wiring Contact Distributor Bad brush motor Contact Distributor Carbon brushes worn out Contact Distributor Bad solenoid Contact Distributor Bad vacuum switch Contact Distributor Vacuum motor Bad wiring Contact Distributor does not run Bad vacuum motor Contact Distributor Carbon brushes worn out Contact Distributor Batteries need to be charged Charge batteries (see Battery Charging) Short run time Batteries need maintenance See Battery Maintenance in this manual Bad cell in battery(s) Replace batteries Bad charger Replace charger Bad solution switch Contact Distributor Little or no solution Clogged solution solenoid Contact Distributor flow Clogged solution filter Remove filter and clean Solution line obstructed Remove solution line and clean Increase flow by twisting solution adjustment knob to the Solution flow adjustment knob in need right. Decrease flow by twisting solution adjustment knob of adjustment to the left. Squeegee clogged Clean debris off squeegee with damp towel Poor water pick up Squeegee blades worn Install new squeegee blades Squeegee not mounted correctly Confirm that the squeegee assembly is securely fastened to the machine and not loose fitting. Vacuum hoses have a hole or are loose Check hose connections and make sure they are firm. Replace hose if damaged. Vacuum hose may be clogged Check hose for debris and remove any clog. Drain hose stopper is loose Tighten drain plug. Batteries need to be charged Charge batteries (see Battery Charging) Vacuum motor is loose Tighten vac motor mounting screws. Do not overtighten or damage will occur. Recovery tank lid is loose Confirm the clear recovery tank lid is securely in place. Recovery tank inlet hole is clogged Drain recovery tank and tilt tank on side. Check the inlet hole for debris and remove debris. Recovery tank is full Drain recovery tank. Float shut off is clogged Remove float shut off from inside recovery tank and remove any debris. 0

11

12 DIA PART NUMBER SOLUTION TANK ASSEMBLY DESCRIPTION REQ'D VF805BD GRIP,HANDLE VA77 SCREW, SELF-TAPPING, ST, M X 6 VV66 WASHER,PLAIN, M X M X VV60 SCREW, M8 X VF59 WASHER,LOCK, M5 X M X VF85 PLUG,EXPANSION 7 VF55 WASHER,PLAIN, M8 X M0 X 8 8 VF806 BUSHING 9 VF80 SUPPORT,RECOVERY TANK 0 VF809A BRACKET,VAC TUBE VF80 SPRING VF800 ADAPTER,TUBE VF80A GASKET,TUBE ADAPTER VF8070-0TD LABEL,LEFT 5 VF806 CONNECTOR, 75A 6 VF877 WIRE, #6 X VF8 DECAL 8 VF6 SCREW, M6 X 5 9 VV607 WASHER,LOCK, M6 8 0 GT0 WASHER,PLAIN, M6 X M6 X.5 6 VF878 WIRE, #6 X 750 VF95 SCREW, M6 X 6 VF875 STANDOFF VF8067 BRACKET 5 VF SCREW, M6 X 0 6 VF8078 SCREEN,FILL 7 VF5 SCREW, SELF-TAPPING, ST, M X 6 8 VF5 SCREW, SELF-TAPPING, ST, M X VA8 WASHER,PLAIN, M X M9 X VF808 PLUG,FILL SCREEN VF8079 COVER,FILL SCREEN VF880 SOLUTION TANK VF807-0TD LABEL,RIGHT VF9900 WHEEL, " 5 VF89 BUSHING 6 VF5A WASHER,PLAIN, M8 X M6.5 X 7 VF65 SCREW, M8 X 50 8 BAT95I BATTERY,V,5AMP HOUR 9 VF8 CASTER, " 0 VF80 TRAY,BATTERY VF807A SPACER,BATTERY VF6 SCREW, M0 X 0 8

13 DIA PART NUMBER SOLUTION TANK ASSEMBLY DESCRIPTION REQ'D VF80 CABLE,BATTERY VF87 CAPS,BATTERY,BLACK VF87R CAPS,BATTERY,RED 5 CHRGR8 CHARGER,V,8AMP 6 VF57 WASHER,PLAIN, M0 X M6 X 8 7 VF58 WASHER,LOCK, M0 8 8 VF SCREW, M8 X 6 9 VF5 NUT, M8 50 VF808 PLATE,LOCK 5 VF86 HOSE BARB 5 VF86 CLAMP (6-5) 5 VF8 TUBING 5 VF806A KIT,LABEL,MARKERS 55 VF0 SCREW, M5 X 5 56 VV60 WASHER,LOCK, M5 57 VF5 WASHER,PLAIN, M5 X M X 58 VF80 PLATE,SQGE,LOCK 59 VF5 SCREW, M8 X 5 60 VF86 WASHER,LOCK, M.7 6 VF8 HANDLE,SQGE,LIFT 6 VF8050A BUSHING 6 VF8 SCREW, M8 X 00 6 VA56 WASHER,PLAIN, M0 X M0 X.5

14

15 DIA PART NUMBER RECOVERY TANK ASSEMBLY DESCRIPTION REQ'D VF800 CLEAR COVER,RECOVERY TANK VF808 DECAL WARNING BATTERY VF8009 ELBOW ADAPTOR,FLOAT VV607 WASHER,LOCK, M6 5 VF5 WASHER,PLAIN, M6 X M6 X 7 6 VF SCREW, M6 X 0 7 VF850 FLOAT 8 VF880 RECOVERY TANK 9 VF58 WASHER,TEETH,LOCK, M6 0 VF95 SCREW, M6 X 6 VF808 CABLE VF8509 PLUG,EXPANSION VF850-9 STRAP,DRAINHOSE VF850- SLEEVE,DRAINHOSE 5 VF850A DRAIN HOSE ASSEMBLY 6 VV0 CLAMP, " 7 VF85 DECAL,BATTERY INSTALLATION 8 ZD5000 MOTOR,VAC STAGE,VDC 9 VF50 NUT,LOCK, M6 0 VF8508 STUD(") VF5 NUT,M6 VF850 SEAT VF00 SCREW, M6 X 6 9 GT0 WASHER,PLAIN, M6 X M6 X VF80 HINGE,RECOVERY TANK 6 VF808TR LOGO (0") 7 VA77 SCREW, SELF-TAPPING, ST, M X 6 8 VV66 WASHER,PLAIN, M X M X 9 VF800A RUBBER HINGE 0 VF800B GASKET VF800X KIT,LID

16

17 DIA PART NUMBER REQ'D VF8080 HUB,CAPS VF806 WHEEL, 8" BRUSH LIFT/DRIVE ASSEMBLY DESCRIPTION VF8600 TRANSAXLE, " ZD7000A TRANSAXLE MOTOR, VDC VF80 BRACKET,TRANSAXLE MOUNT 5 VF57 WASHER,PLAIN, M0 X M6 X 6 6 VF58 WASHER,LOCK, M0 6 7 VF66 SCREW, M0 X 5 8 VF6 SCREW, M0 X 0 9 VF50 NUT,LOCK, M6 8 0 VF5 WASHER,PLAIN, M6 X M6 X 8 VF80 SPACER VF806A BUSHING VF58 WASHER,PLAIN, M X M X VF880 BRACKET,LIFT MOTOR 5 VF89 PIN, M0 X 0 6 VF08 PIN,COTTER, M. X 7 VF80 ACTUATOR 8 VF59 WASHER,LOCK, M8 9 VV60 SCREW, M8 X 0 0 VF55 WASHER,PLAIN, M8 X M0 X VF86 BRACKET,CABLE GUIDE VF85 BRACKET,ACTUATOR VF85 PLATE VF7 SCREW, M X 5 5 VF80A PLATE,BASE TRANSAXLE 6 VF50 NUT,LOCK, M

18

19 DIA PART NUMBER BRUSH/PAD DRIVE ASSEMBLY DESCRIPTION REQ'D VF8A BLOCK,GUIDE VA00 WASHER,PLAIN, M5 X M X GT0 NUT,LOCK, M5 VF SCREW, M8 X 6 5 VF59 WASHER,LOCK, M8 5 6 VF5 WASHER,PLAIN, M8 X M6 X 7 VV07B WASHER,PLAIN, M X M9 X 8 VF86A SUPPORT PLATE,SKIRT 9 VF55 WASHER,PLAIN, M8 X M0 X 0 VV60 SCREW,M8X0 VF58 WASHER,PLAIN,MXMX 0 VF8805 BRACKET,SPRING VF7 SCREW,MX5 VF806A BUSHING 6 5 VF87 SPRING 6 VF8 SCREW,MX0 7 VF880 BRACKET,MOTOR MOUNT 8 VF5A SCREW,M6X0 9 VF8 STUD 0 VF8057 PAD DRIVER, 9" VF50 NUT,LOCK, M6 VF88 SPACER VF9900A BIG MOUTH VA8 SCREW,SELF-TAPPING,ST, M X 5 MF-VF00-A SCREW,SELF-TAPPING, /" - " 6 VF SCREW, 5/6" - " 7 VV098 WASHER,LOCK, 5/6" 8 VF8058 WASHER 9 VF80A PLATE, DRIVE, ASSY 0 VF80 PLATE,DRIVE VF8 STOP,DRIVE RELEASE VF8 SPRING VF8 CLAMP,BRUSH PLATE VV60 WASHER,LOCK, M5 5 VF55 SCREW,SELF-TAPPING,ST,M5 X 0 6 VF SCREW, /8" - " 7 VV60 WASHER,LOCK, /8" 8 VF57 WASHER,PLAIN,M0 X M6 X 9 VF50 NUT,LOCK,M 0 ZD507 KEY, 6.5 X 5 ZD5000 BRUSH MOTOR,VDC,.75HP VF0 SCREW, M5 X 5

20

21 DIA PART NUMBER SOLUTION CONTROL ASSEMBLY DESCRIPTION REQ'D VF5 SCREW, M5 X 6 VF806 SHAFT VV650 SCREW, M X 0 VF5 WASHER,PLAIN, M5 5 VV60 WASHER,LOCK, M5 6 VF0 SCREW, M5 X 5 7 VF56 WASHER,PLAIN, M9.8 X M6 X 8 VF8075 NUT, /8" 9 VF8 CABLE,SOLEID 0 VF88 CLAMP, 6mm VF800 HOSE BARB,TEE VF8 TUBING, 50mm VF80 ELBOW VF8 TUBING, 5mm 5 VF80A ELBOW,SOLUTION TANK 6 VF868 FILTER 7 VF8780 TIE 8 VF85 TUBING, 00mm 9 VF86 TUBING, 80mm 0 VF95 SCREW, M6 X 6 VF5 WASHER,PLAIN, M6 X M6 X VF87 TUBING, 65mm VF80- SOLUTION VALVE SOLEID,VDC VV607 WASHER,LOCK, M6 5 VF80 BRACKET,SOLEID 6 VF50 NUT,LOCK, M6 7 VF88 TUBING, 0mm 8 VV0509 SCREW,M5X0 9 VF88 CLAMP 0 VF50 WASHER,WAVE, M VF807 BRACKET,DRAIN HOSE & VALVE VF8069 LABEL,VALVE VF807 BUSHING VF808 KB,VALVE ADJUST

22

23 DIA PART NUMBER BRUSH SKIRT ASSEMBLY DESCRIPTION REQ'D VF8808 BUMPER VF95 SCREW,M6X6 8 VV607 WASHER,LOCK,M6 8 VF5 WASHER,PLAIN,M6 8 5 VF807 BRACKET,SKIRT MOUNT 6 VF808 PIN,SKIRT 7 VF80 WHEEL," 8 VF8055 BUSHING 9 VF5A WASHER,PLAIN,M8XM6.5X 0 VF6 SCREW,M8X0 VA00 WASHER,PLAIN,M5XM5X.5 6 VA7 SCREW,M5X6 6 VF880 GRIP,BUMPER VF8809 CLAMP,BUMPER 5 VF885 BUMPER 6 VF8807R RIGHT SKIRT,ASSEMBLY 7 VV059 SCREW,MX8 8 VF8807 SKIRT,RIGHT 9 VF809 LATCH,HOOD 0 VV09 WASHER,LOCK,M VF8806 SKIRT,LEFT VF8806L LEFT SKIRT,ASSEMBLY VF8 BLOCK,SKIRT

24

25 DIA PART NUMBER DESCRIPTION CONTROL HOUSING REQ'D VF9 SCREW, M X 7 VF WASHER,PLAIN, M0 X M0 X VF SCREW, M0 X 65 VF50 NUT,LOCK, M6 0 5 GT0 WASHER,PLAIN, M6 6 6 VF878 DIODE, 00V VF878-X DIODE WITH ENDS 7 VF876A SOLEID, V 8 VF87 BREAKER,CIRCUIT,5AMP 9 VF89 LABEL,CIRCUIT BREAKER 0 VF80 HOUSING,CONTROL VF87 BUSHING VF805 LABEL,SPEED CONTROL VF078 SCREW,M X 0 6 VA5077 WASHER,PLAIN, M X M0 X 6 5 VF878 LIGHTS,BATTERY CAPACITY 6 VF8 GASKET 7 VF95 SCREW, M6 X 6 8 VF879 SPACER 6 9 VF87A PANEL,SWITCH (") 0 VF88 LABEL,SWITCH VF87 SWITCH,LIGHTED ROCKER VF877 GAUGE,BRUSH PRESSURE VF875 SWITCH,BRUSH LIFT VF00 SCREW, M6 X 6 5 VF870 KB,SPEED CONTROL 6 VF8709 PIN,HANDLE LOCK 7 VF876 SPRING 8 VF870 PIN,HANDLE ADJUSTMENT 9 VF879 POTIENTIOMETER,.7K 0 VF86 PLATE VF879-0HD SPEED CONTROL,BOARD VF88 SERIAL TAG GV09 COVER VF88 LABEL,CIRCUIT BREAKER 5 VF80A PANEL,CONTROL HOUSING 6 VF870 BATTERY CAPACITY CONTROL,BOARD 7 VF8 GASKET 8 VF990 BREAKER,CIRCUIT, AMP 9 VF807BD HANDLE,RIGHT 0 VF87 BOLT,SHOULDER, M8 X 5 X M6 VF87 SPRING VF5A WASHER,PLAING, M8 X M6.5 X VF806BD HANDLE,LEFT VF SCREW, MX5 5 VF5 WASHER,TEETH, M 6 VF0 SWITCH ASSY 7 VF8707 BRACKET,SWITCH (") 8 VV65 NUT,LOCK, M 9 VF87 TUBE,HANDLE,ADJUSTMENT 50 VF85 SWITCH,KEY 5 VF860 LABEL,KEY SWITCH 5 VF87B STRAIN RELIEF,CORD 5 VF87 SWITCH,TOGGLE

26

27 DIA PART NUMBER DESCRIPTION REQ'D VF50 NUT,LOCK, M VF58 WASHER,PLAIN, M X M6 X VF8 MOUNT,PIVOT VF67 SCREW, M X 0 5 VF8 SCREW, M X 0 6 VF806A BUSHING 7 VF8 CABLE,SQGE,LIFT (") 8 VF8 BUSHING 9 VF80A HOSE 0 VF850 HOLDER,"U" HOSE VF8 SPRING VF807 SHAFT VF85 BRACKET,SPRING VF80 KB, M8 5 VF6 SCREW,M8 X 0 6 VF5A WASHER,PLAIN, M8 X M6.5 X 7 VF8055 BUSHING 8 VF80 WHEEL, " 9 VF86 HOUSING,SQUEEGEE VF806 BLADE SQUEEGEE REAR PU 0 VF89 BLADE,SQUEEGEE,REAR NEOPRENE VF88A LATCH,HOOD VF809 HOOK,REAR SQUEEGEE BACKUP ADJUSTMENT VF0 SCREW, M5 X 70 VF808A RIVET, M X 5 5 GT0 NUT,LOCK, M5 6 VF8 BOLT,SHOULDER, 5/6" X.5" 7 VF89 WHEEL, " 8 VF55 WASHER,PLAIN, M8 X M0 X 9 VV00 NUT,LOCK, 5/6" 0 VF80 BACKUP STRIP,SQUEEGEE,REAR VF80A KIT,SQUEEGEE REAR BACKUP STRIP SQUEEGEE ASSEMBLY VF806 BLADE,SQUEEGEE,FRONT,(PU) VF87 BLADE,SQUEEGEE,FRONT,(NEOPRENE) VF88 BACKUP STRIP,SQUEEGEE,FRONT VF8 KB, M6 6 5 VF50 NUT,LOCK, M6 6 VF8 BRACKET,SQGE,MOUNT 7 VF5 NUT, M6 8 VF59 WASHER,PLAIN, M X M X 9 VF8908A SQUEEGEE ASSY

28

29