about Smeg sinks 4 complementary designs 6 undermount sinks 8 topmount sinks 12

Transcription

1 SINKS

2 VR78 2

3 about Smeg sinks 4 complementary designs 6 undermount sinks 8 topmount sinks 12 3

4 About Smeg sinks At Smeg we understand that kitchen appliances need to be aesthetically beautiful and functional in equal measure. The humble kitchen sink has gone from a functional space in which to wash dishes, to a food preparation area, a drying area, a place to remove food scraps (perhaps via a food waste disposer) and, ultimately, to the focal point of a designer kitchen. Smeg s range of sinks vary from a simple, yet beautifully made, single bowl with drainer sink, through to the flagship of the range a very sophisticated, double-bowl sink with elegant glass sliding chopping boards. A selection of sinks has been designed to specifically complement the iconic Smeg kitchen appliance ranges; for example, the LV range of sinks is shaped to perfectly correspond to the PGA range of cooktops, and the LD range will enhance the Marc Newsondesigned range of ovens and cooktops. The design combination of Smeg Linear products with Smeg LQ sinks is superb. Kitchen sinks are in most cases made of stainless steel, which is defined as a steel alloy with a minimum of % chromium content by mass. Stainless steel does not stain, corrode or rust as easily as ordinary steel. Stainless steel is austenitic metallic but non magnetic. Smeg sinks are made from high-quality AISI304 (iron free) brushed stainless steel with a satin finish, 1mm thick is used for Smeg LD, LV, LQV, LQR, LR, VQ and VST ranges. The standard ranges are made with mm thick stainless steel. The majority of Smeg sinks are made of lightly-brushed satin stainless steel to achieve the same finish as Smeg cooktops, ovens, rangehoods and refrigeration. There are three methods of mounting sinks topmount, flushmount and undermount. Topmounting is the standard method of installation, ie the sink is placed into a cutout and has a low profile. For granite, marble, quartz resin and pure resin etc, flushmounting is often the preferred method as it achieves a completely flat surface. The hole must be perfectly cut to accommodate the exact dimensions of the sink with a small rebate to accommodate the flush fitment of the visible trim. Undermounting is when the sink s trim is perfectly concealed below the bench. It is important when installing undermount sinks that the manufacturer s instructions are followed carefully, using silicon and the brackets provided. The sink should not be glued in place. For both flush and undermounting, the sink should always be at hand for the qualified and skilled fabricator/stonemason to install. 4

5 CLEANING The premium-quality stainless which Smeg uses for its kitchen sinks is extremely durable. Over the course of its life, it will show signs of wear which may change its appearance but does not alter its integrity. Discolouration and marks which may appear on stainless steel are usually caused by water-borne deposits on its surface. Such stains often have a rainbow effect and can be avoided by removing any wet objects (cloths etc) from the sink; it is helpful to dry the sink thoroughly after use. Perforated rubber or plastic mats in the sink will cut down on scratching and marking by pans and tableware. Wash with a solution of dishwashing liquid detergent and water; or a solution of baking soda and water. Rinse and polish dry with paper towel or soft cloth. Never use scouring powders or steel wool as they will scratch stainless steel. You can brighten the sink by polishing with a cloth dipped in vinegar, or in ammonia, or dampen sink and a sponge, sprinkle a little baking soda on sponge and rub sink gently; rinse, then polish dry with a paper towel. Smeg sinks, over time, actually improve with age. The day-to-day touching of plates, pots, utensils etc all add and improve the texture and appearance within its satinfinished surface. 25 YEAR 25 GUARANTEE 5

6 Complementary linear classic 6

7 marc newson 7

8 UNDERMOUNT VSTQ20 undermount sink 16 litres capacity VSTQ40N undermount sink 32 litres capacity VSTQ72N undermount sink 58 litres capacity Accessories TLQ40 timber chopping board TTQ40 polymer chopping board VSH40Q single-bowl stainless steel drainer VSH20Q half-bowl stainless steel drainer 8

9 The VSTQ range was among the first hand-made bowls with 0 corners. The success of this range is due to a rigorous design which is in line with modern trends of simplicity and elegance in the kitchen NB: these are hand-made sinks; variations, though minimal, from indicated measurements might occur. Always have the sink(s) at hand when the qualified fabricator/stonemason is cutting out the benchtop. This will help ensure a perfect fit. 9

10 UNDERMOUNT BST30 undermount sink 21.6 litres capacity BST34 undermount sink 24.5 litres capacity BST45 undermount sink 32.4 litres capacity Accessories DB30 drainer basket DB34 drainer basket DB45 drainer basket TS30 chopping board TS34 chopping board 10 TS45 chopping board

11 NB: these are hand-made sinks; variations, though minimal, from indicated measurements might occur. Always have the sink(s) at hand when the qualified fabricator/stonemason is cutting out the benchtop. This will help ensure a perfect fit. UM4530 undermount sink main: 32.4 litres capacity auxiliary: 21.6 litres capacity overflow plumbing kit supplied UM3434 undermount sink 24.3 litres capacity each bowl overflow plumbing kit supplied 180 UM4545 undermount sink 32.4 litres capacity each bowl overflow plumbing kit supplied 11

12 TOPMOUNT LE861A topmount sink 24.5 litres capacity no taphole punched on request, L or R drainer area LE862A topmount sink 24.5 litres capacity each bowl no taphole punched on request Accessories DB34 drainer basket 12 TS34 chopping board

13 LE116A topmount sink 24.5 litres capacity each bowl no taphole punched on request, L or R drainer area LE102A topmount sink main: 24.5 litres capacity auxiliary: 10 litres capacity no taphole punched on request, L or R drainer area TVN black glass chopping board 13 TVSG silver glass chopping board

14 TOPMOUNT LD861S topmount sink, left-hand drainer LD861D topmount sink, right-hand drainer 27.2 litres capacity pre-punched taphole, L or R drainer area LD862 topmount sink 27.2 litres capacity each bowl pre-punched taphole LD116S topmount sink, left-hand drainer LD116D topmount sink, right-hand drainer 27.2 litres capacity each bowl pre-punched taphole, L or R drainer area modern design 15mm radius corners 20cm deep bowls low profile easy to clean overflow and plumbing kit supplied high-quality 1mm thick brushed stainless steel Accessories TVN black glass chopping board TVSG silver glass chopping board VSH40Q single-bowl stainless steel drainer VSH20Q half-bowl stainless steel drainer 14

15 LD861D/S LD862 LD116D/S TVN/TVSG 15

16 TOPMOUNT Accessories LV951S-3 topmount sink, left-hand drainer LV951D-3 topmount sink, right-hand drainer 36 litres capacity pre-punched taphole, L or R drainer area DB34 drainer basket DB45 drainer basket LV116S-3 topmount sink, left-hand drainer LV116D-3 topmount sink, right-hand drainer 24.5 litres capacity each bowl pre-punched taphole, L or R drainer area TS34 chopping board LV95-3 topmount sink 24.5 litres capacity each bowl pre-punched taphole TS45 chopping board 16

17 LV951D/S-3 LV116D/S-3 LV

18 TOPMOUNT The LQV range features hand-made, 1mm-thick stainless steel bowls with glass/stainless steel sliding work surface. The design complements perfectly the Smeg Linear range of appliances. The designer pop-up plug and waste includes a stainless steel cover. Also included is a sliding 150mm-wide stainless steel colander. LQVS litres capacity each bowl three pre-punched holes for tap fitment two remote-control designer plug & waste reversible stainless steel/silver glass sliding sink covers LQVN litres capacity each bowl three pre-punched holes for tap fitment and two remote-control designer plug & waste reversible stainless steel/black glass sliding sink covers Accessories (suit LQVS862-1, LQVN862-1) 1.0 TLQ40 timber chopping board TTQ40 polymer chopping board 18

19 FEATURE designer pop-up plug and waste with stainless steel cover VR78S 67 litres capacity two pre-punched holes in rear platform for tap and single remote control plug and waste Beautiful and practical, the VQ78R is hand-built of 1mm thick stainless steel, with silver glass chopping boards and sliding stainless steel colander. 19

20 TOPMOUNT The VQ range of sinks was amongst the first hand-made bowls with 0 corners. The success of this range is due to a rigorous design which is in line with the modern trends of simplicity and elegance in the kitchen. LQR862-2 topmount sink 30 litres capacity each bowl two pre-punched holes for tap and remote control for designer waste & plug, either bowl (supplied) LQR116-2 topmount sink 30 litres capacity each bowl two pre-punched holes for tap and remote control for outer bowl designer plug and waste (supplied) reversible for L or R drainer area Accessories LQR100-2 topmount sink main: 29.6 litres auxiliary: 14.7 litres two pre-punched holes for tap and remote control for outer bowl designer waste & plug (supplied) reversible for L or R drainer area TLQ40 timber chopping board TTQ40 polymer chopping board 20 VSH40Q single-bowl stainless steel drainer VSH20Q half-bowl stainless steel drainer

21 NB: each LQR sink is prepunched with two holes in either end of the stainless steel bridge between the two sink bowls. Depending on your drainer side, one hole will be fitted with the remote control square knob to raise or lower strainer plug in the bowl; the other hole will be for the tap. 21

22 TOPMOUNT VQ20 topmount sink 16.8 litres capacity VQ40N topmount sink 33.5 litres capacity VQ40NR topmount sink 33.6 litres capacity Accessories TLQ40 timber chopping board TTQ40 polymer chopping board 22 VSH40Q single-bowl stainless steel drainer VSH20Q half-bowl stainless steel drainer

23 VQ20N VQ40N VQ40NR 10 23

24 TOPMOUNT OR FLUSHMOUNT LR102 sink main: 30 litres auxiliary: 6 litres two pre-punched holes for tap and remote control for outer bowl designer plug and waste (supplied) reversible for L or R drainer area LR861 sink 30 litres capacity two pre-punched holes for tap and remote control for outer bowl designer plug and waste (supplied) reversible for L or R drainer area

25 With the elegant and minimal design of a squareline sink, 10mm radius corners have been introduced to the LR/VR range of sinks for ease of cleaning VR80 sink 64.8 litres capacity two pre-punched holes for tap and remote control for designer plug and waste (supplied) Accessories TLQ40 timber chopping board TTQ40 polymer chopping board 25 VSH40Q single-bowl stainless steel drainer VSH20Q half-bowl stainless steel drainer

26 26

27 Smeg Australia Pty Ltd Sydney Head Office Smeg Service Smeg Spare Parts Smeg Melbourne Australia-wide distributors: Newcastle Wagga Wagga ACT Queensland Tasmania South Australia Western Australia Smeg Australia Pty Ltd is constantly seeking ways to improve the specifications, design and production of its products. Alterations take place continually. Whilst every effort is made to produce up-to-date literature, this brochure should not be regarded as an infallible guide to the current specifications, nor does it constitute an offer for the sale of any particular product. Product cutouts indicated in our literature are indicative only. Actual product only should be used to define cutout sizes. Distributors, agents and retailers are not agents of Smeg Australia and have no authority to bind Smeg Australia by any express or implied undertaking or representation. WARNING: technical specifications and product sizes can be varied by the manufacturer without notice. Cutouts for appliances should only be by physical product measurements. The above information is indicative only. 27

28 28